| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When MSI-X is not enabled, we mask all the interrupts in the interrupt
handler and re-enable them when the interrupt thread runs. If
STATUS_INT_ENABLED is not set, we won't re-enable in the thread.
In order to get the ALIVE interrupt, we allow the ALIVE interrupt
itself, and RX as well in order to receive the ALIVE notification (which
is received as an RX from the firmware.
The problem is that STATUS_INT_ENABLED is clear until the op_mode calls
trans_fw_alive which means that until trans_fw_alive is called, any
notification from the firmware will not be received.
This became a problem when we inserted the pnvm_load exactly between the
ALIVE and trans_fw_alive.
Fix that by calling trans_fw_alive before loading the PNVM. This will
allow to get the notification from the firmware about PNVM load being
complete and continue the flow normally.
This didn't happen on MSI-X because we don't disable the interrupts in
the ISR when MSI-X is available.
The error in the log looks like this:
iwlwifi 0000:00:03.0: Timeout waiting for PNVM load!
iwlwifi 0000:00:03.0: Failed to start RT ucode: -110
iwlwifi 0000:00:03.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
Fixes: 70d3ca86b025 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.0f2cf207aae1.I025d8f724b44f52eadf6c19069352eb9275613a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The allocation of the scatter gather data structure should be done
based on the number of memory chunks that need to be mapped, and it
is not dependent on the overall payload length. Fix it.
In addition, as the skb_to_sgvec() function returns an 'int' do not
assign it to an 'unsigned int' as otherwise the error check would be
useless.
Fixes: 7f5e3038f029 ("wifi: iwlwifi: map entire SKB when sending AMSDUs")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.8c0e23a3d583.I3cb4d6768c9d28ce3da6cd0a6c65466176cfc1ee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is possible to use nl80211 to request to the driver to do allow the
required bus configuration to wake-up the host.
This patch implements the required API for nl80211.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-6-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the device is connected with SDIO bus, it can wake up the host using
either the SDIO controller (that requires MMC_PM_WAKE_SDIO_IRQ
capability) or the out-of-bound IRQ. This patch allows both.
Obviously, the SDIO controller must be able to keep the SDIO device
powered on.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-5-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the host is asleep, the device has wake up the host using the
usual SPI IRQ.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-4-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
WF200 is able to keep the connection with the AP alive while the host is
asleep. So, let's expose this capability to the user.
For now, we don't provide any way to control the device filtering
features. The user has to allow wake-up on any received packets and on
disconnections.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-3-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Just declare fields in the same order in bus_spi.c and bus_sdio.c
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-2-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My previous patch caused a slight code size increase when DEBUG_FS is disabled,
as Stanislaw Gruszka pointed out.
Fix this with an added IS_ENABLED() check.
Fixes: cf6b9ba172dd ("wifi: iwlegacy: don't warn for unused variables with DEBUG_FS=n")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250304144210.997531-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
====================
ath.git patches for v6.15
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
====================
Link: https://lore.kernel.org/linux-wireless/d01b1976-ebe8-48cd-8f49-32bfa00bed7e@oss.qualcomm.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e45a ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e77 ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interrupt status (ISR) bits of RX desc unavailable (RDU) for 8922AE
are B_BE_RDU_CH1_INT_V1 and B_BE_RDU_CH0_INT_V1. With wrong bits, if it
happens, driver can't recognize the situation and prompt a message.
Fix the definition accordingly.
Fixes: aa70f76120ee ("wifi: rtw89: pci: generalize interrupt status bits of interrupt handlers")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250227131907.9864-1-pkshih@realtek.com
|
|
Once update driver blacklist of firmware, users' firmware might be in
the list, and then driver stops working. Since breaking users is not
expected, report a significant message instead of stopping.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250227131228.8457-5-pkshih@realtek.com
|
|
rtw89_build_txpwr_trk_tbl_from_elm()
The format should be "%08x". Fix the mistakes.
Fixes: d60e73e5dd70 ("wifi: rtw89: fw: load TX power track tables from fw_element")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250227131228.8457-4-pkshih@realtek.com
|
|
Add new fields band and port ID to make chips operating on the band and
port ID other than 0, so that multiple vif(s) can be working at the
same time.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250227131228.8457-3-pkshih@realtek.com
|
|
The role_maintain H2C command is to align operating mode of WiFi role,
such as STA or AP modes, between driver and firmware.
Use a struct to fill fields of this H2C command.
Don't change logic at all.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250227131228.8457-2-pkshih@realtek.com
|
|
iwlwifi is the driver of all Intel wifi devices since 2008.
Since then, the hardware has changed a lot, but the firmware
API has changed even more. The need to keep one driver that
supports all those different APIs led us to introduce a new
architecture circa 2012 which allowed us to keep the same
interface to the hardware (DMAs, Tx queues, etc...) with a
new layer to implement the mid-layer between mac80211 and
the firmware. The first component is called the 'transport'
and the latter is called 'operation_mode' a.k.a op_mode.
In 2013 we took advantage of the new architecture to
introduce iwlmvm which allowed us to implement the, then,
new firmware API. This op_mode supports 7260 and up, those
devices supports support at least VHT.
Since then, wifi evolved and so did the firmware. It became
much bigger and took a lot of functionality from the driver.
It became increasingly hard to keep the same op_mode for the
newest devices and we experienced frequent regressions on
older devices. In order to avoid those regressions and keep
the code maintainable, we decided it was about time to start
a new op_mode.
iwlmld is a new op_mode that supports BE200 or newer if the
firmware being used is 97.ucode or newer. If the user has
an older devices or BE200 with .96.ucode, iwlmvm will be
loaded. Of course, this op_mode selection is seamless.
All the features supported in iwlmvm are supported in
iwlmld besides a few seldom used use cases: injection and
Hotspot 2.0. Those are under work.
A few points about the implementation:
* iwlmld doesn't have any mutexes, it relies on the
wiphy_lock
* iwlmld is more "resource oriented": stations, links and
interfaces are allocated and freed only after all the
relevant flows are completed.
* Firmware notifications' sizes are validated in a more
structured way.
We would love to see this new op_mode merged in 6.15. The
firmware for this new driver (.97.ucode) is not yet publicly
available but it'll be sent very soon.
People eager to get an early version of this firmware can
contact Emmanuel at:
emmanuel.grumbach@intel.com
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Co-developed-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Co-developed-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/linux-wireless/20250216094321.537988-1-miriam.rachel.korenblit@intel.com/
[fix Kconfig, fix api/phy.h includes, SPDX tag and coding
style issues, duplicated includes per 0-day robot]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
First 6.15 material:
* cfg80211/mac80211
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
* rtw88
- preparation for RTL8814AU support
* rtw89
- use wiphy_lock/wiphy_work
- preparations for MLO
- BT-Coex improvements
- regulatory support in firmware files
* iwlwifi
- preparations for the new iwlmld sub-driver
* tag 'wireless-next-2025-03-04-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (128 commits)
wifi: iwlwifi: remove mld/roc.c
wifi: mac80211: refactor populating mesh related fields in sinfo
wifi: cfg80211: reorg sinfo structure elements for mesh
wifi: iwlwifi: Fix spelling mistake "Increate" -> "Increase"
wifi: iwlwifi: add Debug Host Command APIs
wifi: iwlwifi: add IWL_MAX_NUM_IGTKS macro
wifi: iwlwifi: add OMI bandwidth reduction APIs
wifi: iwlwifi: remove mvm prefix from iwl_mvm_d3_end_notif
wifi: iwlwifi: remember if the UATS table was read successfully
wifi: iwlwifi: export iwl_get_lari_config_bitmap
wifi: iwlwifi: add support for external 32 KHz clock
wifi: iwlwifi: mld: add a debug level for EHT prints
wifi: iwlwifi: mld: add a debug level for PTP prints
wifi: iwlwifi: remove mvm prefix from iwl_mvm_esr_mode_notif
wifi: iwlwifi: use 0xff instead of 0xffffffff for invalid
wifi: iwlwifi: location api cleanup
wifi: cfg80211: expose update timestamp to drivers
wifi: mac80211: add ieee80211_iter_chan_contexts_mtx
wifi: mac80211: fix integer overflow in hwmp_route_info_get()
wifi: mac80211: Fix possible integer promotion issue
...
====================
Link: https://patch.msgid.link/20250304125605.127914-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
bugfixes for 6.14:
* regressions from this cycle:
- mac80211: fix sparse warning for monitor
- nl80211: disable multi-link reconfiguration (needs fixing)
* older issues:
- cfg80211: reject badly combined cooked monitor,
fix regulatory hint validity checks
- mac80211: handle TXQ flush w/o driver per-sta flush,
fix debugfs for monitor, fix element inheritance
- iwlwifi: fix rfkill, dead firmware handling, rate API
version, free A-MSDU handling, avoid large
allocations, fix string format
- brcmfmac: fix power handling on some boards
* tag 'wireless-2025-03-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: nl80211: disable multi-link reconfiguration
wifi: cfg80211: regulatory: improve invalid hints checking
wifi: brcmfmac: keep power during suspend if board requires it
wifi: mac80211: Fix sparse warning for monitor_sdata
wifi: mac80211: fix vendor-specific inheritance
wifi: mac80211: fix MLE non-inheritance parsing
wifi: iwlwifi: Fix A-MSDU TSO preparation
wifi: iwlwifi: Free pages allocated when failing to build A-MSDU
wifi: iwlwifi: limit printed string from FW file
wifi: iwlwifi: mvm: use the right version of the rate API
wifi: iwlwifi: mvm: don't try to talk to a dead firmware
wifi: iwlwifi: mvm: don't dump the firmware state upon RFKILL while suspend
wifi: iwlwifi: mvm: clean up ROC on failure
wifi: iwlwifi: fw: avoid using an uninitialized variable
wifi: iwlwifi: fw: allocate chained SG tables for dump
wifi: mac80211: remove debugfs dir for virtual monitor
wifi: mac80211: Cleanup sta TXQs on flush
wifi: nl80211: reject cooked mode if it is set along with other flags
====================
Link: https://patch.msgid.link/20250304124435.126272-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This file should never have been part of the commit, remove it.
Fixes: af3be9088404 ("wifi: iwlwifi: support ROC version 6")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In certain cases, hardware might provide packets with a
length greater than the maximum native Wi-Fi header length.
This can lead to accessing and modifying fields in the header
within the ath12k_dp_rx_h_undecap_nwifi function for
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type and
potentially resulting in invalid data access and memory corruption.
Add a sanity check before processing the SKB to prevent invalid
data access in the undecap native Wi-Fi function for the
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20250211090302.4105141-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently Tx completion for few exception packets are received from
firmware and the tx status updated to mac80211. The tx status values of
HAL_WBM_REL_HTT_TX_COMP_STATUS_DROP and HAL_WBM_REL_HTT_TX_COMP_STATUS_TTL
are considered as tx failure and reported as tx failure to mac80211.
But these failure status is due to internal firmware tx drop and these
packets were not tried to transmit in the air.
In case of mesh this invalid tx status report might trigger mpath broken
issue due to increase in mpath fail average.
So do not report these tx status as tx failure instead free the skb
by calling ieee80211_free_txskb(), and that will be accounted as dropped
frame.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241122173432.2064858-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support for calibration-like properties without 'ath11k' prefix,
while still keeping everything backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250225-b-wifi-qcom-calibration-variant-v1-5-3b2aa3f89c53@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support for calibration-like properties without 'ath10k' prefix,
while still keeping everything backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250225-b-wifi-qcom-calibration-variant-v1-4-3b2aa3f89c53@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Function ath12k_mac_setup_bcn_tmpl_ema() retrieves 'bss_conf'
only to get BSSID index which is an overhead because the
caller ath12k_mac_setup_bcn_tmpl() has already stored this
locally. Pass the index as an input instead.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-6-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add new input parameter to ath12k_mac_setup_bcn_tmpl_ema() for
'tx_arvif' as the caller ath12k_mac_setup_bcn_tmpl() already
stores it locally. Avoid duplicate retrieval.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-5-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Create a new function ath12k_mac_get_tx_arvif() to retrieve 'arvif'
for the transmitted interface of the MBSSID set. This clean up will
help modifying the same code path for MLO changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-4-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Function ath11k_mac_setup_bcn_tmpl() retrieves tx_arvif only for
a sanity check and then calls ath11k_mac_setup_bcn_tmpl_mbssid()
or ath11k_mac_setup_bcn_tmpl_ema() both of which again retrieve
the same pointer. Instead store the pointer and pass it to the
latter two functions. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Create a new function ath11k_mac_get_tx_arvif() to retrieve 'arvif'
for the transmitted interface of the MBSSID set. This will help
modifying the same code path to reflect mac80211 data structure
changes to support MLO. This also fixes an issue in
ath11k_mac_update_vif_chan() where tx_arvif is not reset to NULL
inside for loop during each iteration. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
There is a spelling mistake in a IWL_DEBUG_RATE message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20250227221917.658401-1-colin.i.king@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
irq_set_affinity_and_hint()
irq_set_affinity_hint() API is deprecated now, so let's use the recommended
equivalent irq_set_affinity_and_hint().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250225053447.16824-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
error path
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath12k_pci_msi_alloc(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ.
This may end up with a warning from the IRQ core that is expecting the
affinity hint to be cleared before freeing the IRQ:
kernel/irq/manage.c:
/* make sure affinity_hint is cleaned up */
if (WARN_ON_ONCE(desc->affinity_hint))
desc->affinity_hint = NULL;
So to fix this issue, clear the IRQ affinity hint before calling
ath12k_pci_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Fixes: a3012f206d07 ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
error path
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath11k_pci_alloc_msi(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ. This results in the
below warning:
WARNING: CPU: 7 PID: 349 at kernel/irq/manage.c:1929 free_irq+0x278/0x29c
Call trace:
free_irq+0x278/0x29c
ath11k_pcic_free_irq+0x70/0x10c [ath11k]
ath11k_pci_probe+0x800/0x820 [ath11k_pci]
local_pci_probe+0x40/0xbc
The warning is due to not clearing the affinity hint before freeing the
IRQs.
So to fix this issue, clear the IRQ affinity hint before calling
ath11k_pcic_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 39564b475ac5 ("wifi: ath11k: fix boot failure with one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
during scanning
For some packets, we could not get channel information from PPDU status.
And this causes wrong frequencies being reported. Parse the channel
information from IE if provided by AP to fix this.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250220064357.17962-1-pkshih@realtek.com
|
|
For 8852BTE, 8852CE, and 8922AE, TKIP encryption and decryption
will be handled by hardware. All other chips will retain their
existing software-based encryption and decryption.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250220062344.15836-1-pkshih@realtek.com
|
|
Currently, sometimes, the station is unable to identify the configured
AP SSID in its scan results when the AP is not broadcasting its name
publicly and has a hidden SSID.
Currently, channel dwell time for an ath12k station is 30 ms. Sometimes,
station can send broadcast probe request to AP close to the end of dwell
time. In some of these cases, before AP sends a response to the received
probe request, the dwell time on the station side would come to an end.
So, the station will move to scan next channel and will not be able to
acknowledge the unicast probe response.
Resolve this issue by increasing station's channel dwell time to 70 ms,
so that the it remains on the same channel for a longer period. This
would increase the station's chance of receiving probe response from the
AP. The station will then send a response acknowledgment back to the AP,
thus leading to successful scan and BSS discovery.
With an increased dwell time, scan would take longer than it takes now.
But, this fix is an improvement for hidden SSID scan issue.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207060005.153835-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the defintition of those APIs, those will be used in a later patch.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.d842253ee55d.I2e8d65f22d5acde70ed6be16f913160a93d06852@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This macro represents the number of IGTKS the FW can support.
Will be used in a later patch.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.a8e3c7461f13.If63cbc73eaf328b2c1d7c8e57627eb93c35b0c70@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This adds the API definitions needed for OMI bandwidth reduction.
Will be used in a later patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.4d34e8f5a3df.Idd6185cdb8d8a133f92032db9278c1510961cbdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is not op mode specific.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.c99748f63511.I5c8dcc46e992e76c82fdf7dbee65957cbdca1b43@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow to read the table once, and not any time the command is
sent. The actual use of this will be in a later patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.61801b78a2cb.I710a766888f370a75b47116fec29d41c106b13ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will now be called from another opmode we are writing.
iwl_fill_lari_config will only be used for the older ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.9bb7fbc592a6.I8850691eac7c8471257f3031e8c05905afc72f70@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case the BIOS allows it, instruct the firmware to use the external 32
KHz clock.
The op mode specific implementation (i.e. reading the BIOS table) will
come in a later patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.9aae3f74fee0.I25ae45ef02b9ea387b512f974c1f3e5367a537e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is required for EHT related debug prints.
As there are no more available debug levels, delete IWL_DL_EXTERNAL,
which is not used, and replace it with IWL_DL_EHT.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.9b1e0d87e7e4.Iea6c1329f7b6312a73896f9a9d9bce72bd6548e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is required for PTP related debug prints.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.866f8f66b1d7.I764abcb845d992d058c753ce8fa9d45fed2ff4ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is not specific to mvm.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.c536eeaae129.I848307be6df21913c0ce3eb6baef715cd401db1a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware is now able to understand 0xff and that is more widely
used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.c6719e6dc0a6.Ifd149101fa886730602dbbb02f980be8e554fe84@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove the version suffix from the latest version of the range
request command structs and the range response notification structs.
In addition, don't use MVM in the API file as it is not MVM specific.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250212073923.294b7109e0be.I229ceef5933e825815d84c33855cadd62687ee04@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The reference to il_rate_mcs is inside of an #ifdef, causing a W=1 warning:
drivers/net/wireless/intel/iwlegacy/4965-rs.c:189:38: error: unused variable 'il_rate_mcs' [-Werror,-Wunused-const-variable]
static const struct il_rate_mcs_info il_rate_mcs[RATE_COUNT] = {
Replace the #ifdef with a PTR_IF() for better compile time analysis.
The dead code will still get eliminated, but the warning goes away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250225145359.1126786-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on
suspend and then re-probed on resume.
This conflicts with some embedded boards that require to remain powered.
They will fail on resume with:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
This commit checks for the Device Tree property 'cap-power-off-cards'.
If this property is not set, it means that we do not have the capability
to power off and should therefore remain powered.
Signed-off-by: Matthias Proske <email@matthias-proske.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250212185941.146958-2-email@matthias-proske.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
While processing TPC stats received from firmware, there are chances that
the tpc_stats might not be filled and the data is not available. This can
happen under two scenarios. First, when firmware sends a non-zero event
count before event count 0. When this happens, tpc_stats will be checked
for data before memory allocation and the tpc_stats will be unavailable.
Second, when memory allocation failed when event count received is 0 and
the firmware still sends a non-zero event. When this happens, memory will
not be allocated for tpc_stats though event count is 0, so when non-zero
event count is received, tpc_stats will be empty. There are checks to
validate if tpc_stats variable is filled that are used in two subsequent
places, but these are placed after tpc_stats is dereference without
checking if it is NULL or has valid data.
Fix this by removing the mentioned checks and adding a NULL check after
assigning tpc_stats to check if it is valid.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Closes: https://scan7.scan.coverity.com/#/project-view/52668/11354?selectedIssue=1637145
Fixes: f0c3bb78e42f ("wifi: ath12k: Add Support to Parse TPC Event from Firmware")
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250221041250.769491-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
