| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver code allows for the disabling of MSI interrupts; however the
module_parm line was missed and the option fails to show with modinfo.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.15+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 33511b157bbcebaef853cc1811992b664a2e5862 ("rtlwifi: add support to
send beacon frame"), the mechanism for sending beacons was established. That
patch works correctly for rtl8192cu, but there is a possibility of getting
the following warnings in the PCI drivers:
WARNING: CPU: 1 PID: 2439 at net/mac80211/driver-ops.h:12
ieee80211_bss_info_change_notify+0x179/0x1d0 [mac80211]()
wlp5s0: Failed check-sdata-in-driver check, flags: 0x0
The warning is followed by a NULL pointer dereference as follows:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000006
IP: [<ffffffffc073998e>] rtl_get_tcb_desc+0x5e/0x760 [rtlwifi]
This problem was reported at http://thread.gmane.org/gmane.linux.kernel.wireless.general/138645,
but no solution was found at that time.
The problem was also reported at https://bugzilla.kernel.org/show_bug.cgi?id=9744
and this solution was developed and tested there.
The USB driver works with a NULL final argument in the adapter_tx() callback;
however, the PCI drivers need a struct rtl_tcb_desc in that position.
Fixes: 33511b157bbc ("rtlwifi: add support to send beacon frame.")
Signed-off-by: Luis Felipe Dominguez Vega <lfdominguez@nauta.cu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On the 2GHz and and on the 5GHZ band only the extpa_gain setting from
the 5GHz band was checked. this patch makes it check the property from
the correct band.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes commit eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
which stopped the driver from functioning.
Firmware data has been allocated using vmalloc(), resulting in memory
that cannot be used for DMA. Hence the firmware was first copied to a
buffer allocated with kmalloc() in the original code. This patch reverts
the commit and only calls "kfree()" to release the buffer after sending
the data. This fixes the memory leak without breaking the driver.
Add a comment to the kmemdup() calls to explain why this is done, and abort
if memory allocation fails.
Tested on a Topic Miami-Florida board which contains the rsi SDIO chip.
Also added the same kfree() call to the USB glue driver. This was not
tested on actual hardware though, as I only have the SDIO version.
Fixes: eae79b4f3e82 ("rsi: fix memory leak in rsi_load_ta_instructions()")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
|
|
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.
There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...
Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The code checks the total number of iterations to differentiate
between regular scan and scheduled scan. However, regular scan has
a total of one iteration, not zero. As a result, regular scan will
have lower priority than it should have, and in case scheduled
scan is already running when regular scan is requested, regular scan
will be delayed until scheduled scan is aborted.
Fix that by checking for total iterations number of one as an
identifier for regular scan.
Fixes: 133c8259f885 ("iwlwifi: mvm: rename generic_scan_cmd functions to dwell")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When the card is not owned by the PCIe bus, we need to
acquire ownership first. This flow is implemented in
iwl_pcie_prepare_card_hw. Because of a hardware bug, we
need to disable link power management before we can
request ownership otherwise the other user of the device
won't get notified that we are requesting the device which
will prevent us from acquire ownership.
Same holds for the down flow where we need to make sure
that any other potential user is notified that the driver
is going down.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
devices (3160).
* revert the new RBD allocation model because it introduced
a bug when running on weak VM setups.
* a new device IDs
|
|
This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This reverts commit 5f17570354f91275b0a37a4da33d29a2ab57d32e.
This patch introduced a high latency in buffer allocation
under extreme load. This latency caused a firmwre crash.
The same scenario works fine with this patch reverted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add preemptive flag to scheduled scan command flags. Without this
flag, all scan requests after scheduled scan was started will be
delayed until scheduled scan stops. As a result, P2P_FIND will be
blocked while scheduled scan is active.
This flag was omitted during refactoring.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add new 3165 devices support.
Add one new 8000 series device support.
Remove support for 0x0000, 0xC030 and 0xD030 sub-system IDs
in the 8000 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The time event is initialized relatively late in interface (mvmvif)
initialization, so it's possible to fail before that happens. As a
consequence, the driver will crash if it ever tries to delete this
time event in case initialization was unsuccessful.
Avoid this by using the time event's vif pointer to indicate validity.
The vif pointer is != NULL whenever the id is != TE_MAX, except for
this special error case where the vif pointer will have the correct
property (as the whole memory is cleared on allocation) whereas the
id is 0, causing a crash in trying to delete the time event from the
list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
For 8000 series, we need to access the device to know what
firmware to load. Before we do so, we need to prepare the
device otherwise we might not be able to access the
hardware.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Because of the missing return, the macVersion value was being
overwritten with an invalid register read
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
iwl_trans_pcie_alloc needs to return a non-zero value
if it fails. Otherwise the iwl_drv_start will think that
the allocation succeeded.
Remove the duplication of err and ret variable and use ret
which is the name we usually use in other places of the
driver.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
While cleanig the access to those hw-dependent registers,
instead of using the product family type, wrong condition was added
mistakenly and enabled 8000 family devices a forbidden access
to HW registers, fix it.
Fixes: 95411d0455cc ("iwlwifi: pcie: Control access to the NIC's PM registers via iwl_cfg")
Signed-off-by: Dreyfuss, Haim <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
|
|
Sometimes when setting an igtk key the station maybe NULL.
In the of case igtk the function will skip to the end, and
try to print sta->addr, if sta is Null - we will access a
Null pointer.
Avoid accessing a Null pointer when setting a igtk key &
the sta == NULL, and print a default MAC address instead.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181
CC: <stable@vger.kernel.org> [3.17+]
Fixes: 34c8b24ff284 ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
During verification of error handling in brcmf_cfg80211_attach() a
null pointer dereference occurred upon calling brcmf_p2p_detach()
from brcmf_detach(). This should only be called when the
brcmf_cfg80211_attach() has succeeded.
Fixes: f7a40873d2fa ("brcmfmac: assure p2pdev is unregistered upon driver unload")
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When freeing the driver ifp pointer it should also be removed from
the driver interface list, which is what brcmf_remove_interface()
does. Otherwise, the ifp pointer will be freed twice triggering
a kernel oops.
Fixes: f37d69a4babc ("brcmfmac: free ifp for non-netdev interface in p2p module")
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds missing break statement at the end of
EVENT_BT_COEX_WLAN_PARA_CHANGE switch section.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Major changes:
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
|
|
On some hardware reading WCID entries table results getting 0xff
numbers, no matter of value written there before. This cause assigning
the same WCID for different stations and makes not possible to connect
to more than one station.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When unloading the driver with a p2pdev interface it resulted in
a warning upon calling wiphy_unregister() and subsequently a crash
in the driver. This patch assures the p2pdev is unregistered calling
unregister_wdev() before doing the wiphy_unregister().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Moving two functions in p2p.c as is so next change will be
easier to review.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Making it more clear by freeing the ifp in same place where the
vif object is freed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The bus interface functions txctl and rxctl may be used while the device
can not be accessed, eg. upon driver .remove() callback. This patch will
immediately return -EIO when this is the case which speeds up the module
unload.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The .get_station() cfg80211 callback is used in several scenarios. In
managed mode it can obtain information about the access-point and its
BSS parameters. In managed mode it can also obtain information about
TDLS peers. In AP mode it can obtain information about connected
clients.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Switch from using semi hard coded interface combinations. This makes
it easier to announce what the firmware actually supports. This fixes
the case where brcmfmac announces p2p but the firmware doesn't
support it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add a feature flag to reflect the firmware's p2p capability.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We expect EEPROM per-rate power table to be filled with
s6 values and warn user if values are invalid. However,
there appear to be devices which don't have this section
of EEPROM initialized. In such case we should ignore
the values and leave the driver power tables set to zero.
Note that vendor driver doesn't care about this case but
mt76x2 skips 0xff per value. We take mt76x2's approach.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: Chunfan Chen <jeffc@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add the support of channel switching functionality, similar
to ath9k support.
Tested with TP-Link TL-WN722N and TL-WN821N.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some time ago the function debugfs_create_devm_seqfile() was
introduced in debugfs. The caller simply needs to provide a
device pointer and read function. The function brcmf_debugfs_add_entry()
is now simply a wrapper only doing the work for CONFIG_BRCMDBG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The watchdog reset as done in brcmf_pcie_buscoreprep() is not
sufficient. It needs to modify PCIe core registers as well
which is properly done by brcmf_pcie_reset_device() after the
chip recognition is done. So the faulty watchdog reset can be
removed as it was causing driver reload to fail and hang the
system requiring a power-cycle. Instead the call to to the
brcmf_pcie_reset_device() function is done twice in the unload.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The information provided by chipinfo is also provided by the
revinfo debugfs entry. Removing it from debugfs.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On device to host data using msgbuf the read pointer gets updated
once all data is processed. Updating this pointer more frequently
allows the firmware to add more data quicker. This will result in
slightly higher and more stable throughput on CPU bounded host
processors.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The variable "fw_version" is used in the _ResetDigitalProcedure1().
but It is not initialized. so I add init codes for "fw_version" and
"fw_subversion".
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
rtl92cu_rx_query_desc set a isampdu twice.
but second code is related to isfirst_ampdu.
so i change it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to
"RTL8192CU".
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
_rtl92c_phy_rf6052_config_parafile
in the _rtl92c_phy_rf6052_config_parafile(), cases
RF90_PATH_A and RF90_PATH_B call the same routine.
so i remove one of these routine. also the return
routine is duplicated. so i remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While working on getting my rtl8821au driver in pretty shape for
inclusion, it is dicosvered that the tm_trigger flag is used only for
the first device using this driver.
This flag handles the thermal power management in the hardware.
To change this add a entry in sttruct rtl_dm, so each device can handle
is separately.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary.
because RTL8192CU chipset is only USB interface.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
is unnecessary. because rtlwifi/rtl8192cu codes aren't shared.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
