summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)AuthorFilesLines
2022-01-20rtlwifi: rtl8192cu: Fix WARNING when calling local_irq_restore() with ↵Larry Finger1-0/+1
interrupts enabled commit 8b144dedb928e4e2f433a328d58f44c3c098d63e upstream. Syzbot reports the following WARNING: [200~raw_local_irq_restore() called with IRQs enabled WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10 Hardware initialization for the rtl8188cu can run for as long as 350 ms, and the routine may be called with interrupts disabled. To avoid locking the machine for this long, the current routine saves the interrupt flags and enables local interrupts. The problem is that it restores the flags at the end without disabling local interrupts first. This patch fixes commit a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long disable of IRQs"). Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Fixes: a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long disable of IRQs") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-16ath11k: Fix buffer overflow when scanning with extraieSven Eckelmann1-3/+3
commit a658c929ded7ea3aee324c8c2a9635a5e5a38e7f upstream. If cfg80211 is providing extraie's for a scanning process then ath11k will copy that over to the firmware. The extraie.len is a 32 bit value in struct element_info and describes the amount of bytes for the vendor information elements. The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This section can have a (payload) length up to 65535 bytes because the WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and could have created a scan request which cannot be parsed correctly by the firmware. But the bigger problem was the allocation of the buffer. It has to align the TLV sections by 4 bytes. But the code was using an u8 to store the newly calculated length of this section (with alignment). And the new calculated length was then used to allocate the skbuff. But the actual code to copy in the data is using the extraie.len and not the calculated "aligned" length. The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled was 264 bytes during tests with a QCA Milan card. But it only allocated 8 bytes (264 bytes % 256) for it. As consequence, the code to memcpy the extraie into the skb was then just overwriting data after skb->end. Things like shinfo were therefore corrupted. This could usually be seen by a crash in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus address). Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Cc: stable@vger.kernel.org Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08iwlwifi: mvm: retry init flow if failedMordechay Goodstein5-8/+47
commit 5283dd677e52af9db6fe6ad11b2f12220d519d0c upstream. In some very rare cases the init flow may fail. In many cases, this is recoverable, so we can retry. Implement a loop to retry two more times after the first attempt failed. This can happen in two different situations, namely during probe and during mac80211 start. For the first case, a simple loop is enough. For the second case, we need to add a flag to prevent mac80211 from trying to restart it as well, leaving full control with the driver. Cc: <stable@vger.kernel.org> Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211110150132.57514296ecab.I52a0411774b700bdc7dedb124d8b59bf99456eb2@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_modeLorenzo Bianconi1-2/+2
commit 6e53d6d26920d5221d3f4d4f5ffdd629ea69aa5c upstream. Fix the following NULL pointer dereference in mt7915_get_phy_mode routine adding an ibss interface to the mt7915 driver. [ 101.137097] wlan0: Trigger new scan to find an IBSS to join [ 102.827039] wlan0: Creating new IBSS network, BSSID 26:a4:50:1a:6e:69 [ 103.064756] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 103.073670] Mem abort info: [ 103.076520] ESR = 0x96000005 [ 103.079614] EC = 0x25: DABT (current EL), IL = 32 bits [ 103.084934] SET = 0, FnV = 0 [ 103.088042] EA = 0, S1PTW = 0 [ 103.091215] Data abort info: [ 103.094104] ISV = 0, ISS = 0x00000005 [ 103.098041] CM = 0, WnR = 0 [ 103.101044] user pgtable: 4k pages, 39-bit VAs, pgdp=00000000460b1000 [ 103.107565] [0000000000000000] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 103.116590] Internal error: Oops: 96000005 [#1] SMP [ 103.189066] CPU: 1 PID: 333 Comm: kworker/u4:3 Not tainted 5.10.75 #0 [ 103.195498] Hardware name: MediaTek MT7622 RFB1 board (DT) [ 103.201124] Workqueue: phy0 ieee80211_iface_work [mac80211] [ 103.206695] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--) [ 103.212705] pc : mt7915_get_phy_mode+0x68/0x120 [mt7915e] [ 103.218103] lr : mt7915_mcu_add_bss_info+0x11c/0x760 [mt7915e] [ 103.223927] sp : ffffffc011cdb9e0 [ 103.227235] x29: ffffffc011cdb9e0 x28: ffffff8006563098 [ 103.232545] x27: ffffff8005f4da22 x26: ffffff800685ac40 [ 103.237855] x25: 0000000000000001 x24: 000000000000011f [ 103.243165] x23: ffffff8005f4e260 x22: ffffff8006567918 [ 103.248475] x21: ffffff8005f4df80 x20: ffffff800685ac58 [ 103.253785] x19: ffffff8006744400 x18: 0000000000000000 [ 103.259094] x17: 0000000000000000 x16: 0000000000000001 [ 103.264403] x15: 000899c3a2d9d2e4 x14: 000899bdc3c3a1c8 [ 103.269713] x13: 0000000000000000 x12: 0000000000000000 [ 103.275024] x11: ffffffc010e30c20 x10: 0000000000000000 [ 103.280333] x9 : 0000000000000050 x8 : ffffff8006567d88 [ 103.285642] x7 : ffffff8006563b5c x6 : ffffff8006563b44 [ 103.290952] x5 : 0000000000000002 x4 : 0000000000000001 [ 103.296262] x3 : 0000000000000001 x2 : 0000000000000001 [ 103.301572] x1 : 0000000000000000 x0 : 0000000000000011 [ 103.306882] Call trace: [ 103.309328] mt7915_get_phy_mode+0x68/0x120 [mt7915e] [ 103.314378] mt7915_bss_info_changed+0x198/0x200 [mt7915e] [ 103.319941] ieee80211_bss_info_change_notify+0x128/0x290 [mac80211] [ 103.326360] __ieee80211_sta_join_ibss+0x308/0x6c4 [mac80211] [ 103.332171] ieee80211_sta_create_ibss+0x8c/0x10c [mac80211] [ 103.337895] ieee80211_ibss_work+0x3dc/0x614 [mac80211] [ 103.343185] ieee80211_iface_work+0x388/0x3f0 [mac80211] [ 103.348495] process_one_work+0x288/0x690 [ 103.352499] worker_thread+0x70/0x464 [ 103.356157] kthread+0x144/0x150 [ 103.359380] ret_from_fork+0x10/0x18 [ 103.362952] Code: 394008c3 52800220 394000e4 7100007f (39400023) Fixes: 37f4ca907c46 ("mt76: mt7915: register per-phy HE capabilities for each interface") Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/ddae419a740f1fb9e48afd432035e9f394f512ee.1637239456.git.lorenzo@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08rt2x00: do not mark device gone on EPROTO errors during startStanislaw Gruszka1-0/+3
commit ed53ae75693096f1c10b4561edd31a07b631bd72 upstream. As reported by Exuvo is possible that we have lot's of EPROTO errors during device start i.e. firmware load. But after that device works correctly. Hence marking device gone by few EPROTO errors done by commit e383c70474db ("rt2x00: check number of EPROTO errors") caused regression - Exuvo device stop working after kernel update. To fix disable the check during device start. Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/ Reported-and-tested-by: Exuvo <exuvo@exuvo.se> Fixes: e383c70474db ("rt2x00: check number of EPROTO errors") Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18ath10k: fix invalid dma_addr_t token assignmentArnd Bergmann1-1/+9
commit 937e79c67740d1d84736730d679f3cb2552f990e upstream. Using a kernel pointer in place of a dma_addr_t token can lead to undefined behavior if that makes it into cache management functions. The compiler caught one such attempt in a cast: drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface': drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast] 5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf; | ^ Looking through how this gets used down the way, I'm fairly sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL devices, and if it was accessed, that would be a bug. Change the assignment to use a known-invalid address token instead, which avoids the warning and makes it easier to catch bugs if it does end up getting used. Fixes: e263bdab9c0e ("ath10k: high latency fixes for beacon buffer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18wcn36xx: Fix discarded frames due to wrong sequence numberLoic Poulain1-2/+7
[ Upstream commit 113f304dbc1627c6ec9d5329d839964095768980 ] The firmware is offering features such as ARP offload, for which firmware crafts its own (QoS)packets without waking up the host. Point is that the sequence numbers generated by the firmware are not in sync with the host mac80211 layer and can cause packets such as firmware ARP reponses to be dropped by the AP (too old SN). To fix this we need to let the firmware manages the sequence numbers by its own (except for QoS null frames). There is a SN counter for each QoS queue and one global/baseline counter for Non-QoS. Fixes: 84aff52e4f57 ("wcn36xx: Use sequence number allocated by mac80211") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18wcn36xx: add proper DMA memory barriers in rx pathBenjamin Li1-1/+11
[ Upstream commit 9bfe38e064af5decba2ffce66a2958ab8b10eaa4 ] This is essentially exactly following the dma_wmb()/dma_rmb() usage instructions in Documentation/memory-barriers.txt. The theoretical races here are: 1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l write, thus performing DMA into the wrong address. 2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl & WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb). Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Benjamin Li <benl@squareup.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18libertas: Fix possible memory leak in probe and disconnectWang Hai1-0/+2
[ Upstream commit 9692151e2fe7a326bafe99836fd1f20a2cc3a049 ] I got memory leak as follows when doing fault injection test: unreferenced object 0xffff88812c7d7400 (size 512): comm "kworker/6:1", pid 176, jiffies 4295003332 (age 822.830s) hex dump (first 32 bytes): 00 68 1e 04 81 88 ff ff 01 00 00 00 00 00 00 00 .h.............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490 [<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470 [<ffffffffa02c9873>] if_usb_probe+0x63/0x446 [usb8xxx] [<ffffffffa022668a>] usb_probe_interface+0x1aa/0x3c0 [usbcore] [<ffffffff82b59630>] really_probe+0x190/0x480 [<ffffffff82b59a19>] __driver_probe_device+0xf9/0x180 [<ffffffff82b59af3>] driver_probe_device+0x53/0x130 [<ffffffff82b5a075>] __device_attach_driver+0x105/0x130 [<ffffffff82b55949>] bus_for_each_drv+0x129/0x190 [<ffffffff82b593c9>] __device_attach+0x1c9/0x270 [<ffffffff82b5a250>] device_initial_probe+0x20/0x30 [<ffffffff82b579c2>] bus_probe_device+0x142/0x160 [<ffffffff82b52e49>] device_add+0x829/0x1300 [<ffffffffa02229b1>] usb_set_configuration+0xb01/0xcc0 [usbcore] [<ffffffffa0235c4e>] usb_generic_driver_probe+0x6e/0x90 [usbcore] [<ffffffffa022641f>] usb_probe_device+0x6f/0x130 [usbcore] cardp is missing being freed in the error handling path of the probe and the path of the disconnect, which will cause memory leak. This patch adds the missing kfree(). Fixes: 876c9d3aeb98 ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-3-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18libertas_tf: Fix possible memory leak in probe and disconnectWang Hai1-0/+2
[ Upstream commit d549107305b4634c81223a853701c06bcf657bc3 ] I got memory leak as follows when doing fault injection test: unreferenced object 0xffff88810a2ddc00 (size 512): comm "kworker/6:1", pid 176, jiffies 4295009893 (age 757.220s) hex dump (first 32 bytes): 00 50 05 18 81 88 ff ff 00 00 00 00 00 00 00 00 .P.............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490 [<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470 [<ffffffffa02a1530>] if_usb_probe+0x60/0x37c [libertas_tf_usb] [<ffffffffa022668a>] usb_probe_interface+0x1aa/0x3c0 [usbcore] [<ffffffff82b59630>] really_probe+0x190/0x480 [<ffffffff82b59a19>] __driver_probe_device+0xf9/0x180 [<ffffffff82b59af3>] driver_probe_device+0x53/0x130 [<ffffffff82b5a075>] __device_attach_driver+0x105/0x130 [<ffffffff82b55949>] bus_for_each_drv+0x129/0x190 [<ffffffff82b593c9>] __device_attach+0x1c9/0x270 [<ffffffff82b5a250>] device_initial_probe+0x20/0x30 [<ffffffff82b579c2>] bus_probe_device+0x142/0x160 [<ffffffff82b52e49>] device_add+0x829/0x1300 [<ffffffffa02229b1>] usb_set_configuration+0xb01/0xcc0 [usbcore] [<ffffffffa0235c4e>] usb_generic_driver_probe+0x6e/0x90 [usbcore] [<ffffffffa022641f>] usb_probe_device+0x6f/0x130 [usbcore] cardp is missing being freed in the error handling path of the probe and the path of the disconnect, which will cause memory leak. This patch adds the missing kfree(). Fixes: c305a19a0d0a ("libertas_tf: usb specific functions") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211020120345.2016045-2-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mwifiex: Send DELBA requests according to specJonas Dreßler1-2/+3
[ Upstream commit cc8a8bc37466f79b24d972555237f3d591150602 ] While looking at on-air packets using Wireshark, I noticed we're never setting the initiator bit when sending DELBA requests to the AP: While we set the bit on our del_ba_param_set bitmask, we forget to actually copy that bitmask over to the command struct, which means we never actually set the initiator bit. Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command struct. Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Acked-by: Pali Rohár <pali@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18rsi: stop thread firstly in rsi_91x_init() error handlingZiyang Xuan1-0/+1
[ Upstream commit 515e7184bdf0a3ebf1757cc77fb046b4fe282189 ] When fail to init coex module, free 'common' and 'adapter' directly, but common->tx_thread which will access 'common' and 'adapter' is running at the same time. That will trigger the UAF bug. ================================================================== BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x] Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777 CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19 Call Trace: dump_stack_lvl+0xe2/0x152 print_address_description.constprop.0+0x21/0x140 ? rsi_tx_scheduler_thread+0x50f/0x520 kasan_report.cold+0x7f/0x11b ? rsi_tx_scheduler_thread+0x50f/0x520 rsi_tx_scheduler_thread+0x50f/0x520 ... Freed by task 111873: kasan_save_stack+0x1b/0x40 kasan_set_track+0x1c/0x30 kasan_set_free_info+0x20/0x30 __kasan_slab_free+0x109/0x140 kfree+0x117/0x4c0 rsi_91x_init+0x741/0x8a0 [rsi_91x] rsi_probe+0x9f/0x1750 [rsi_usb] Stop thread before free 'common' and 'adapter' to fix it. Fixes: 2108df3c4b18 ("rsi: add coex support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt7915: fix muar_idx in mt7915_mcu_alloc_sta_req()Shayne Chen1-1/+1
[ Upstream commit 161cc13912d3c3e8857001988dfba39be842454a ] For broadcast/multicast wcid, the muar_idx should be 0xe. Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt7915: fix sta_rec_wtbl tag lenShayne Chen1-1/+1
[ Upstream commit afa0370f3a3a64af6d368da0bedd72ab2a026cd0 ] Fix tag len error for sta_rec_wtbl, which causes fw parsing error for the tags placed behind it. Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt7915: fix possible infinite loop release semaphoreLorenzo Bianconi1-1/+1
[ Upstream commit e500c9470e26be66eb2bc6de773ae9091149118a ] Fix possible infinite loop in mt7915_load_patch if mt7915_mcu_patch_sem_ctrl always returns an error. Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt76x02: fix endianness warnings in mt76x02_mac.cLorenzo Bianconi1-6/+7
[ Upstream commit c33edef520213feccebc22c9474c685b9fb60611 ] Fix the following sparse warning in mt76x02_mac_write_txwi and mt76x02_mac_tx_rate_val routines: drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19: warning: restricted __le16 degrades to intege warning: cast from restricted __le16 drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28: warning: incorrect type in assignment (different base types) expected restricted __le16 [usertype] rate got unsigned long Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt7615: fix endianness warning in mt7615_mac_write_txwiLorenzo Bianconi1-6/+9
[ Upstream commit d81bfb41e30c42531536c5d2baa4d275a8309715 ] Fix the following sparse warning in mt7615_mac_write_txwi routine: drivers/net/wireless/mediatek/mt76/mt7615/mac.c:758:17: warning: incorrect type in assignment expected restricted __le32 [usertype] got unsigned long Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Fixes: d4bf77bd74930 ("mt76: mt7615: introduce mt7663u support to mt7615_write_txwi") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath10k: fix max antenna gain unitSven Eckelmann2-3/+6
[ Upstream commit 0a491167fe0cf9f26062462de2a8688b96125d48 ] Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB steps). This isn't the case for max_antenna_gain - which is still expected by the firmware as dB. The firmware is converting it from dB to the internal (twicepower) representation when it calculates the limits of a channel. This can be seen in tpc_stats when configuring "12" as max_antenna_gain. Instead of the expected 12 (6 dB), the tpc_stats shows 24 (12 dB). Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057. Fixes: 02256930d9b8 ("ath10k: use proper tx power unit") Signed-off-by: Sven Eckelmann <seckelmann@datto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18b43: fix a lower bounds testDan Carpenter1-1/+1
[ Upstream commit 9b793db5fca44d01f72d3564a168171acf7c4076 ] The problem is that "channel" is an unsigned int, when it's less 5 the value of "channel - 5" is not a negative number as one would expect but is very high positive value instead. This means that "start" becomes a very high positive value. The result of that is that we never enter the "for (i = start; i <= end; i++) {" loop. Instead of storing the result from b43legacy_radio_aci_detect() it just uses zero. Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073621.GE8404@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18b43legacy: fix a lower bounds testDan Carpenter1-1/+1
[ Upstream commit c1c8380b0320ab757e60ed90efc8b1992a943256 ] The problem is that "channel" is an unsigned int, when it's less 5 the value of "channel - 5" is not a negative number as one would expect but is very high positive value instead. This means that "start" becomes a very high positive value. The result of that is that we never enter the "for (i = start; i <= end; i++) {" loop. Instead of storing the result from b43legacy_radio_aci_detect() it just uses zero. Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Büsch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211006073542.GD8404@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath9k: Fix potential interrupt storm on queue resetLinus Lüssing1-1/+3
[ Upstream commit 4925642d541278575ad1948c5924d71ffd57ef14 ] In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt 19.07 we could force a silent restart of a device with no serial output when we were sending a high amount of UDP traffic (iperf3 at 80 MBit/s in both directions from external hosts, saturating the wifi and causing a load of about 4.5 to 6) and were then triggering an ath9k_queue_reset(). Further debugging showed that the restart was caused by the ath79 watchdog. With disabled watchdog we could observe that the device was constantly going into ath_isr() interrupt handler and was returning early after the ATH_OP_HW_RESET flag test, without clearing any interrupts. Even though ath9k_queue_reset() calls ath9k_hw_kill_interrupts(). With JTAG we could observe the following race condition: 1) ath9k_queue_reset() ... -> ath9k_hw_kill_interrupts() -> set_bit(ATH_OP_HW_RESET, &common->op_flags); ... <- returns 2) ath9k_tasklet() ... -> ath9k_hw_resume_interrupts() ... <- returns 3) loops around: ... handle_int() -> ath_isr() ... -> if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) return IRQ_HANDLED; x) ath_reset_internal(): => never reached <= And in ath_isr() we would typically see the following interrupts / interrupt causes: * status: 0x00111030 or 0x00110030 * async_cause: 2 (AR_INTR_MAC_IPQ) * sync_cause: 0 So the ath9k_tasklet() reenables the ath9k interrupts through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED without actually clearing the interrupt. To fix this IRQ storm also clear/disable the interrupts again when we are in reset state. Cc: Sven Eckelmann <sven@narfation.org> Cc: Simon Wunderlich <sw@simonwunderlich.de> Cc: Linus Lüssing <linus.luessing@c0d3.blue> Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset") Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath10k: sdio: Add missing BH locking around napi_schdule()Fabio Estevam1-1/+4
[ Upstream commit 019edd01d174ce4bb2e517dd332922514d176601 ] On a i.MX-based board with a QCA9377 Wifi chip, the following errors are seen after launching the 'hostapd' application: hostapd /etc/wifi.conf Configuration file: /etc/wifi.conf wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! Using interface wlan0 with hwaddr 00:1f:7b:31:04:a0 and ssid "thessid" IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: interface state COUNTRY_UPDATE->ENABLED wlan0: AP-ENABLED NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! ... Fix this problem by adding the BH locking around napi-schedule(), in the same way it was done in commit e63052a5dd3c ("mlx5e: add add missing BH locking around napi_schdule()"). Its commit log provides the following explanation: "It's not correct to call napi_schedule() in pure process context. Because we use __raise_softirq_irqoff() we require callers to be in a context which will eventually lead to softirq handling (hardirq, bh disabled, etc.). With code as is users will see: NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! " Fixes: cfee8793a74d ("ath10k: enable napi on RX path for sdio") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210824144339.2796122-1-festevam@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath10k: Fix missing frame timestamp for beacon/probe-respLoic Poulain1-0/+4
[ Upstream commit e6dfbc3ba90cc2b619229be56b485f085a0a8e1c ] When receiving a beacon or probe response, we should update the boottime_ns field which is the timestamp the frame was received at. (cf mac80211.h) This fixes a scanning issue with Android since it relies on this timestamp to determine when the AP has been seen for the last time (via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter). Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1629811733-7927-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: Fix memory leak in ath11k_qmi_driver_event_workBaochen Qiang1-1/+3
[ Upstream commit 72de799aa9e3e064b35238ef053d2f0a49db055a ] The buffer pointed to by event is not freed in case ATH11K_FLAG_UNREGISTERING bit is set, resulting in memory leak, so fix it. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Baochen Qiang <bqiang@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210913180246.193388-4-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: fix packet drops due to incorrect 6 GHz freq value in rx statusPradeep Kumar Chitrapu2-6/+13
[ Upstream commit 9d6ae1f5cf733c0e8d7f904c501fd015c4b9f0f4 ] Frequency in rx status is being filled incorrectly in the 6 GHz band as channel number received is invalid in this case which is causing packet drops. So fix that. Fixes: 5dcf42f8b79d ("ath11k: Use freq instead of channel number in rx path") Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210722102054.43419-2-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: Avoid race during regd updatesSriram R4-17/+14
[ Upstream commit 1db2b0d0a39102238fcbf9092cefa65a710642e9 ] Whenever ath11k is bootup with a user country already set, cfg80211 notifies this country info to ath11k soon after registration, where the notification is sent to the firmware for fetching the rules of this user country input. Multiple race conditions could be seen in this scenario where a new request is either lost as pointed in [1] or a new regd overwrites the default regd provided by the firmware during bootup. Note that, the default regd is used for intersection purpose and hence it should not be overwritten. The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED flag which is updated after completion of core registration, whereas the reg notification from cfg80211 and wmi events for the corresponding request can happen much before that. Since the ATH11K_FLAG_REGISTERED is currently used to determine if the event containing reg rules belong to default regd or for user request, there is a possibility of the default regd getting overwritten. Since the default reg rules will be received only once per pdev on firmware load, the above flag based check can be replaced with a check to see if default_regd is already set, so that we can now always update the new_regd. Also if the new_regd is set, this will be always used to update the reg rules for the registered phy. [1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/ Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1 Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: fix some sleeping in atomic bugsDan Carpenter1-9/+7
[ Upstream commit aadf7c81a0771b8f1c97dabca6a48bae1b387779 ] The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs() take a "gfp" parameter but they since they take spinlocks, the allocations they do have to be atomic. This causes a bug because ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags. The fix is to use GFP_ATOMIC and remove the unused parameters. Fixes: bd6478559e27 ("ath11k: Add direct buffer ring support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210812070434.GE31863@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18wilc1000: fix possible memory leak in cfg_scan_result()Ajay Singh1-2/+1
[ Upstream commit 3c719fed0f3a5e95b1d164609ecc81c4191ade70 ] When the BSS reference holds a valid reference, it is not freed. The 'if' condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check is used. The issue is solved by removing the unnecessary 'if' check because cfg80211_put_bss() already performs the NULL validation. Fixes: 6cd4fa5ab691 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()") Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18wcn36xx: Fix Antenna Diversity SwitchingBryan O'Donoghue1-1/+3
[ Upstream commit 701668d3bfa03dabc5095fc383d5315544ee5b31 ] We have been tracking a strange bug with Antenna Diversity Switching (ADS) on wcn3680b for a while. ADS is configured like this: A. Via a firmware configuration table baked into the NV area. 1. Defines if ADS is enabled. 2. Defines which GPIOs are connected to which antenna enable pin. 3. Defines which antenna/GPIO is primary and which is secondary. B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N) N is a bitmask of available antenna. Setting N to 3 indicates a bitmask of enabled antenna (1 | 2). Obviously then we can set N to 1 or N to 2 to fix to a particular antenna and disable antenna diversity. C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX) XX is the number of beacons between each antenna RSSI check. Setting this value to 50 means, every 50 received beacons, run the ADS algorithm. D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY) YY is a two's complement integer which specifies the RSSI decibel threshold below which ADS will run. We default to -60db here, meaning a measured RSSI <= -60db will trigger an ADS probe. E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z) Z is a hysteresis value, indicating a delta which the RSSI must exceed for the antenna switch to be valid. For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and AntennaId-2-RSSI == -58db then firmware will not switch antenna. The threshold needs to be -57db or better to satisfy the criteria. F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION. This feature bit is used by the firmware to report if ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to toggle this bit to enable or disable ADS. ADS works like this: A. Every XX beacons the firmware switches to or remains on the primary antenna. B. The firmware then sends a Request-To-Send (RTS) packet to the AP. C. The firmware waits for a Clear-To-Send (CTS) response from the AP. D. The firmware then notes the received RSSI on the CTS packet. E. The firmware then repeats steps A-D on the secondary antenna. F. Subsequently if the RSSI on the measured antenna is better than ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the measured antenna becomes the active antenna. G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at all even if there is a substantially better RSSI on the alternative antenna. What we have been observing is that the RTS packet is being sent but the MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is corrupted only when the link is encrypted, if the AP is open the RTS MAC is correct. Similarly if we configure the firmware to an RTS/CTS sequence for regular data - the transmitted RTS MAC is correctly formatted. Internally the wcn36xx firmware uses the indexes in the SMD commands to populate and extract data from specific entries in an STA lookup table. The AP's MAC appears a number of times in different indexes within this lookup table, so the MAC address extracted for the data-transmit RTS and the MAC address extracted for the ADS/RTS packet are not the same STA table index. Our analysis indicates the relevant firmware STA table index is "bssSelfStaIdx". There is an STA populate function responsible for formatting the MAC address of the bssSelfStaIdx including byte-swapping the MAC address. Its clear then that the required STA populate command did not run for bssSelfStaIdx. So taking a look at the sequence of SMD commands sent to the firmware we see the following downstream when moving from an unencrypted to encrypted BSS setup. - WLAN_HAL_CONFIG_BSS_REQ - WLAN_HAL_CONFIG_STA_REQ - WLAN_HAL_SET_STAKEY_REQ Upstream in wcn36xx we have - WLAN_HAL_CONFIG_BSS_REQ - WLAN_HAL_SET_STAKEY_REQ The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ. No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for populating the STA lookup table in the firmware and once done the MAC sent by the ADS routine is in the correct byte-order. This bug is apparent with ADS but it is also the case that any other firmware routine that depends on the "bssSelfStaIdx" would retrieve malformed data on an encrypted link. Fixes: 3e977c5c523d ("wcn36xx: Define wcn3680 specific firmware parameters") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Tested-by: Benjamin Li <benl@squareup.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18wcn36xx: Correct band/freq reporting on RXLoic Poulain2-1/+25
[ Upstream commit 8a27ca39478270e07baf9c09aa0c99709769ba03 ] For packets originating from hardware scan, the channel and band is included in the buffer descriptor (bd->rf_band & bd->rx_ch). For 2Ghz band the channel value is directly reported in the 4-bit rx_ch field. For 5Ghz band, the rx_ch field contains a mapping index (given the 4-bit limitation). The reserved0 value field is also used to extend 4-bit mapping to 5-bit mapping to support more than 16 5Ghz channels. This change adds correct reporting of the frequency/band, that is used in scan mechanism. And is required for 5Ghz hardware scan support. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18iwlwifi: mvm: disable RX-diversity in powersaveJohannes Berg1-0/+3
[ Upstream commit e5322b9ab5f63536c41301150b7ce64605ce52cc ] Just like we have default SMPS mode as dynamic in powersave, we should not enable RX-diversity in powersave, to reduce power consumption when connected to a non-MIMO AP. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211017113927.fc896bc5cdaa.I1d11da71b8a5cbe921a37058d5f578f1b14a2023@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mwl8k: Fix use-after-free in mwl8k_fw_state_machine()Zheyu Ma1-1/+1
[ Upstream commit 257051a235c17e33782b6e24a4b17f2d7915aaec ] When the driver fails to request the firmware, it calls its error handler. In the error handler, the driver detaches device from driver first before releasing the firmware, which can cause a use-after-free bug. Fix this by releasing firmware first. The following log reveals it: [ 9.007301 ] BUG: KASAN: use-after-free in mwl8k_fw_state_machine+0x320/0xba0 [ 9.010143 ] Workqueue: events request_firmware_work_func [ 9.010830 ] Call Trace: [ 9.010830 ] dump_stack_lvl+0xa8/0xd1 [ 9.010830 ] print_address_description+0x87/0x3b0 [ 9.010830 ] kasan_report+0x172/0x1c0 [ 9.010830 ] ? mutex_unlock+0xd/0x10 [ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] __asan_report_load8_noabort+0x14/0x20 [ 9.010830 ] mwl8k_fw_state_machine+0x320/0xba0 [ 9.010830 ] ? mwl8k_load_firmware+0x5f0/0x5f0 [ 9.010830 ] request_firmware_work_func+0x172/0x250 [ 9.010830 ] ? read_lock_is_recursive+0x20/0x20 [ 9.010830 ] ? process_one_work+0x7a1/0x1100 [ 9.010830 ] ? request_firmware_nowait+0x460/0x460 [ 9.010830 ] ? __this_cpu_preempt_check+0x13/0x20 [ 9.010830 ] process_one_work+0x9bb/0x1100 Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1634356979-6211-1-git-send-email-zheyuma97@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mt76: mt7915: fix an off-by-one bound checkRyder Lee1-1/+1
[ Upstream commit d45dac0732a287fc371a23f257cce04e65627947 ] The bounds check on datalen is off-by-one, so fix it. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath: dfs_pattern_detector: Fix possible null-pointer dereference in ↵Tuo Li1-4/+6
channel_detector_create() [ Upstream commit 4b6012a7830b813799a7faf40daa02a837e0fd5b ] kzalloc() is used to allocate memory for cd->detectors, and if it fails, channel_detector_exit() behind the label fail will be called: channel_detector_exit(dpd, cd); In channel_detector_exit(), cd->detectors is dereferenced through: struct pri_detector *de = cd->detectors[i]; To fix this possible null-pointer dereference, check cd->detectors before the for loop to dereference cd->detectors. Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18brcmfmac: Add DMI nvram filename quirk for Cyberbook T116 tabletHans de Goede1-0/+10
[ Upstream commit 49c3eb3036e6359c5c20fe76c611a2c0e0d4710e ] The Cyberbook T116 tablet contains quite generic names in the sys_vendor and product_name DMI strings, without this patch brcmfmac will try to load: "brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which is way too generic. The nvram file shipped on the factory Android image contains the exact same settings as those used on the AcePC T8 mini PC, so point the new DMI nvram filename quirk to the acepc-t8 nvram file. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18rtw88: fix RX clock gate setting while fifo dumpZong-Zhe Yang2-4/+4
[ Upstream commit c5a8e90730a322f236731fc347dd3afa5db5550e ] When fw fifo dumps, RX clock gating should be disabled to avoid something unexpected. However, the register operation ran into a mistake. So, we fix it. Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210927111830.5354-1-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath10k: high latency fixes for beacon bufferAlagu Sankar1-8/+23
[ Upstream commit e263bdab9c0e8025fb7f41f153709a9cda51f6b6 ] Beacon buffer for high latency devices does not use DMA. other similar buffer allocation methods in the driver have already been modified for high latency path. Fix the beacon buffer allocation left out in the earlier high latency changes. Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> [fabio: adapt it to use ar->bus_param.dev_type ] Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210818232627.2040121-1-festevam@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: Change DMA_FROM_DEVICE to DMA_TO_DEVICE when map reinjected packetsBaochen Qiang1-2/+2
[ Upstream commit 86a03dad0f5ad8182ed5fcf7bf3eec71cd96577c ] For fragmented packets, ath11k reassembles each fragment as a normal packet and then reinjects it into HW ring. In this case, the DMA direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise invalid payload will be reinjected to HW and then delivered to host. What is more, since arbitrary memory could be allocated to the frame, we don't know what kind of data is contained in the buffer reinjected. Thus, as a bad result, private info may be leaked. Note that this issue is only found on Intel platform. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Baochen Qiang <bqiang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: add handler for scan event WMI_SCAN_EVENT_DEQUEUEDWen Gong1-0/+2
[ Upstream commit 441b3b5911f8ead7f2fe2336587b340a33044d58 ] When wlan interface is up, 11d scan is sent to the firmware, and the firmware needs to spend couple of seconds to complete the 11d scan. If immediately a normal scan from user space arrives to ath11k, then the normal scan request is also sent to the firmware, but the scan started event will be reported to ath11k until the 11d scan complete. When timed out for the scan started in ath11k, ath11k stops the normal scan and the firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan. ath11k has no handler for the event and then timed out for the scan completed in ath11k_scan_stop(), and ath11k prints the following error message. [ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out [ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110 [ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110 Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to get rid of the above error message. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: Avoid reg rules update during firmware recoverySriram R1-0/+11
[ Upstream commit 69a0fcf8a9f2273040d03e5ee77c9689c09e9d3a ] During firmware recovery, the default reg rules which are received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite the currently configured user regd. See below snap for example, root@OpenWrt:/# iw reg get | grep country country FR: DFS-ETSI country FR: DFS-ETSI country FR: DFS-ETSI country FR: DFS-ETSI root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f w_crash <snip> [ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered root@OpenWrt:/# iw reg get | grep country country FR: DFS-ETSI country US: DFS-FCC country US: DFS-FCC country US: DFS-FCC In the above, the user configured country 'FR' is overwritten when the rules of default country 'US' are received and updated during recovery. Hence avoid processing of these rules in general during firmware recovery as they have been already applied during driver registration or after last set user country is configured. This scenario applies for both AP and STA devices basically because cfg80211 is not aware of the recovery and only the driver recovers, but changing or resetting of the reg domain during recovery is not needed so as to continue with the configured regdomain currently in use. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mwifiex: Properly initialize private structure on interface type changesJonas Dreßler1-3/+7
[ Upstream commit c606008b70627a2fc485732a53cc22f0f66d0981 ] When creating a new virtual interface in mwifiex_add_virtual_intf(), we update our internal driver states like bss_type, bss_priority, bss_role and bss_mode to reflect the mode the firmware will be set to. When switching virtual interface mode using mwifiex_init_new_priv_params() though, we currently only update bss_mode and bss_role. In order for the interface mode switch to actually work, we also need to update bss_type to its proper value, so do that. This fixes a crash of the firmware (because the driver tries to execute commands that are invalid in AP mode) when switching from station mode to AP mode. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18mwifiex: Run SET_BSS_MODE when changing from P2P to STATION vif-typeJonas Dreßler1-18/+4
[ Upstream commit c2e9666cdffd347460a2b17988db4cfaf2a68fb9 ] We currently handle changing from the P2P to the STATION virtual interface type slightly different than changing from P2P to ADHOC: When changing to STATION, we don't send the SET_BSS_MODE command. We do send that command on all other type-changes though, and it probably makes sense to send the command since after all we just changed our BSS_MODE. Looking at prior changes to this part of the code, it seems that this is simply a leftover from old refactorings. Since sending the SET_BSS_MODE command is the only difference between mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and STATION interface type. This does not fix any particular bug and just "looked right", so there's a small chance it might be a regression. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18ath11k: Align bss_chan_info structure with firmwareSeevalamuthu Mariappan2-1/+3
[ Upstream commit feab5bb8f1d4621025dceae7eef62d5f92de34ac ] pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed at the beginning. This causes invalid values in survey dump. Hence, align the structure with the firmware. Note: The firmware releases follow this order since the feature was implemented. Also, it is not changing across the branches including QCA6390. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by: Ritesh Singh <ritesi@codeaurora.org> Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-11-18rsi: Fix module dev_oper_mode parameter descriptionMarek Vasut3-8/+13
commit 31f97cf9f0c31143a2a6fcc89c4a1286ce20157e upstream. The module parameters are missing dev_oper_mode 12, BT classic alone, add it. Moreover, the parameters encode newlines, which ends up being printed malformed e.g. by modinfo, so fix that too. However, the module parameter string is duplicated in both USB and SDIO modules and the dev_oper_mode mode enumeration in those module parameters is a duplicate of macros used by the driver. Furthermore, the enumeration is confusing. So, deduplicate the module parameter string and use __stringify() to encode the correct mode enumeration values into the module parameter string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with 'BT classic alone' to clarify what those modes really mean. Fixes: 898b255339310 ("rsi: add module parameter operating mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Fuzzey <martin.fuzzey@flowbird.group> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: <stable@vger.kernel.org> # 4.17+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18rsi: fix rate mask set leading to P2P failureMartin Fuzzey4-65/+50
commit b515d097053a71d624e0c5840b42cd4caa653941 upstream. P2P client mode was only working the first time. On subsequent connection attempts the group was successfully created but no data was sent (no transmitted data packets were seen with a sniffer). The reason for this was that the hardware was being configured in fixed rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band. In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow the 11b rates in the 2.4GHz band which updated common->fixedrate_mask. rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum allowed rate, or 0xffff = auto if none was found. However that calculation did not account for the different rate sets allowed in the different bands leading to the error. Fixing set_min_rate() would result in 6Mb/s being used all the time which is not what we want either. The reason the problem did not occur on the first connection is that rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for the *current* band. When it was called that was still 2.4GHz as the switch is done later. So the when set_min_rate() was subsequently called after the switch to 5GHz it still had a mask of zero, leading to defaulting to auto mode. Fix this by differentiating the case of a single rate being requested, in which case the hardware will be used in fixed rate mode with just that rate, and multiple rates being requested, in which case we remain in auto mode but the firmware rate selection algorithm is configured with a restricted set of rates. Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18rsi: fix key enabled check causing unwanted encryption for vap_id > 0Martin Fuzzey3-1/+4
commit 99ac6018821253ec67f466086afb63fc18ea48e2 upstream. My previous patch checked if encryption should be enabled by directly checking info->control.hw_key (like the downstream driver). However that missed that the control and driver_info members of struct ieee80211_tx_info are union fields. Due to this when rsi_core_xmit() updates fields in "tx_params" (driver_info) it can overwrite the control.hw_key, causing the result of the later test to be incorrect. With the current structure layout the first byte of control.hw_key is overlayed with the vap_id so, since we only test if control.hw_key is NULL / non NULL, a non zero vap_id will incorrectly enable encryption. In basic STA and AP modes the vap_id is always zero so it works but in P2P client mode a second VIF is created causing vap_id to be non zero and hence encryption to be enabled before keys have been set. Fix this by extracting the key presence flag to a new field in the driver private tx_params structure and populating it first. Fixes: 314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18rsi: fix occasional initialisation failure with BT coexMartin Fuzzey3-3/+18
commit 9b14ed6e11b72dd4806535449ca6c6962cb2369d upstream. When BT coexistence is enabled (eg oper mode 13, which is the default) the initialisation on startup sometimes silently fails. In a normal initialisation we see usb 1-1.3: Product: Wireless USB Network Module usb 1-1.3: Manufacturer: Redpine Signals, Inc. usb 1-1.3: SerialNumber: 000000000001 rsi_91x: rsi_probe: Initialized os intf ops rsi_91x: rsi_load_9116_firmware: Loading chunk 0 rsi_91x: rsi_load_9116_firmware: Loading chunk 1 rsi_91x: rsi_load_9116_firmware: Loading chunk 2 rsi_91x: Max Stations Allowed = 1 But sometimes the last log is missing and the wlan net device is not created. Running a userspace loop that resets the hardware via a GPIO shows the problem occurring ~5/100 resets. The problem does not occur in oper mode 1 (wifi only). Adding logs shows that the initialisation state machine requests a MAC reset via rsi_send_reset_mac() but the firmware does not reply, leading to the initialisation sequence being incomplete. Fix this by delaying attaching the BT adapter until the wifi initialisation has completed. With this applied I have done > 300 reset loops with no errors. Fixes: 716b840c7641 ("rsi: handle BT traffic in driver") Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18wcn36xx: handle connection loss indicationBenjamin Li1-11/+33
commit d6dbce453b19c64b96f3e927b10230f9a704b504 upstream. Firmware sends delete_sta_context_ind when it detects the AP has gone away in STA mode. Right now the handler for that indication only handles AP mode; fix it to also handle STA mode. Cc: stable@vger.kernel.org Signed-off-by: Benjamin Li <benl@squareup.com> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18mwifiex: Try waking the firmware until we get an interruptJonas Dreßler1-5/+23
commit 8e3e59c31fea5de95ffc52c46f0c562c39f20c59 upstream. It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the 88W8897 card sometimes ignores or misses when we try to wake it up by writing to the firmware status register. This leads to the firmware wakeup timeout expiring and the driver resetting the card because we assume the firmware has hung up or crashed. Turns out that the firmware actually didn't hang up, but simply "missed" our wakeup request and didn't send us an interrupt with an AWAKE event. Trying again to read the firmware status register after a short timeout usually makes the firmware wake up as expected, so add a small retry loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to check whether the card woke up. The number of tries and timeout lengths for this were determined experimentally: The firmware usually takes about 500 us to wake up after we attempt to read the status register. In some cases where the firmware is very busy (for example while doing a bluetooth scan) it might even miss our requests for multiple milliseconds, which is why after 15 tries the waiting time gets increased to 10 ms. The maximum number of tries it took to wake the firmware when testing this was around 20, so a maximum number of 50 tries should give us plenty of safety margin. Here's a reproducer for those firmware wakeup failures I've found: 1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on) 2) Connect to any wifi network (makes firmware go into wifi powersaving mode, not deep sleep) 3) Make sure bluetooth is turned off (to ensure the firmware actually enters powersave mode and doesn't keep the radio active doing bluetooth stuff) 4) To confirm that wifi powersaving is entered ping a device on the LAN, pings should be a few ms higher than without powersaving 5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and suspends the firmware extremely often 6) Wait until things explode, for me it consistently takes <5 minutes BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681 Cc: stable@vger.kernel.org Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-18mwifiex: Read a PCI register after writing the TX ring write pointerJonas Dreßler1-0/+8
commit e5f4eb8223aa740237cd463246a7debcddf4eda1 upstream. On the 88W8897 PCIe+USB card the firmware randomly crashes after setting the TX ring write pointer. The issue is present in the latest firmware version 15.68.19.p21 of the PCIe+USB card. Those firmware crashes can be worked around by reading any PCI register of the card after setting that register, so read the PCI_VENDOR_ID register here. The reason this works is probably because we keep the bus from entering an ASPM state for a bit longer, because that's what causes the cards firmware to crash. This fixes a bug where during RX/TX traffic and with ASPM L1 substates enabled (the specific substates where the issue happens appear to be platform dependent), the firmware crashes and eventually a command timeout appears in the logs. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681 Cc: stable@vger.kernel.org Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-30 09:59:42 +0300