| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
mt76 patches for 4.20
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* tx power configuration fix for 76x2
* more progress on mt76x0e support
* support for getting firmware version via ethtool
* fix for rx buffer allocation regression on usb
* fix for handling powersave responses
* fix for mt76x2 beacon transmission
|
|
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
|
|
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.19
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes: d9c52fd17cb48 ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath10k_hw_diag_fast_download() generally has good boundary checking, but
it misses verifying that the next metadata header actually fits in the
remaining buffer space. Add such a check.
Fixes: 39501ea64116 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There were a lot of Magnitude Mismatch while getting FFT samples on my
hardware (Atheros AR9462. I've compared the reported magnitude with
the data in the FFT bin, and the FFT bin was less accurate:
[ 5395.193030] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.194525] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.196012] ath: phy0: FFT HT20 frame: max mag 0x88,max_mag_idx 28,
,magnitude 0x88 max_exp 0, data[28] = 0x88
[ 5395.197509] ath: phy0: FFT HT20 frame: max mag 0x6C,max_mag_idx 28,
,magnitude 0x6C max_exp 0, data[28] = 0x68
[ 5395.199015] ath: phy0: FFT HT20 frame: max mag 0x78,max_mag_idx 28,
,magnitude 0x78 max_exp 0, data[28] = 0x78
[ 5395.200497] ath: phy0: FFT HT20 frame: max mag 0xA1,max_mag_idx 28,
,magnitude 0xA1 max_exp 0, data[28] = 0xA0
[ 5395.202011] ath: phy0: FFT HT20 frame: max mag 0x91,max_mag_idx 28,
,magnitude 0x91 max_exp 0, data[28] = 0x90
[ 5395.203482] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.204999] ath: phy0: FFT HT20 frame: max mag 0x27,max_mag_idx 4,
,magnitude 0x27 max_exp 0, data[4] = 0x20
[ 5395.206461] ath: phy0: FFT HT20 frame: max mag 0x41,max_mag_idx 28,
,magnitude 0x41 max_exp 0, data[28] = 0x40
[ 5395.207977] ath: phy0: FFT HT20 frame: max mag 0x51,max_mag_idx 28,
,magnitude 0x51 max_exp 0, data[28] = 0x50
[ 5395.209454] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.210940] ath: phy0: FFT HT20 frame: max mag 0x40,max_mag_idx 28,
,magnitude 0x40 max_exp 0, data[28] = 0x40
[ 5395.212441] ath: phy0: FFT HT20 frame: max mag 0x59,max_mag_idx 28,
,magnitude 0x59 max_exp 0, data[28] = 0x58
[ 5395.213932] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.215428] ath: phy0: FFT HT20 frame: max mag 0x7D,max_mag_idx 28,
,magnitude 0x7D max_exp 0, data[28] = 0x78
[ 5395.216910] ath: phy0: FFT HT20 frame: max mag 0x8C,max_mag_idx 28,
,magnitude 0x8C max_exp 0, data[28] = 0x88
[ 5395.218413] ath: phy0: FFT HT20 frame: max mag 0x7B,max_mag_idx 28,
,magnitude 0x7B max_exp 0, data[28] = 0x78
[ 5395.219900] ath: phy0: FFT HT20 frame: max mag 0x43,max_mag_idx 28,
,magnitude 0x43 max_exp 0, data[28] = 0x40
It seems like the lower 3 bits on my hardware are always zeroed, but the
magnitude matches otherwise. Therefore, let's not make the magnitude
check so strict so we can get those samples released to userspace.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
FFT max index retrieval was not retrieved correctly for HT20/HT40 FFT
frames. Fixing the retrieval allows us to remove the fixup function as
well. While at it, split the spectral_max_index function into versions
for ht20 and ht40 to simplify the code.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the loop break like this, there are false "FFT report truncated"
messages because the iterator is not advanced as the check expects.
Instead, just return, for a single frame there is nothing left to be
done anyways.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is helpful to see whether spectral samples get discarded.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches for 4.20
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
|
|
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make sure that wifi device is of supported variant by checking it's CHIP ID
before completing a probe sequence.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Waiting for "completion" to be set in FW load thread can not be used
in case PCIe remove is called before FW load work was scheduled.
Just wait for work completion instead to avoid problems.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Extract platform-independent PCIe driver code into a separate file, and
use it from platform-specific modules.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
A few include directives were missing in bus.h resulting in dependency
of include order in other modules. Add missing includes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rename several functions to indicate that they are platform specific.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move platform-independent PCIe data structure to a separate header file
so it can be reused by different devices.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
tx_lock name will later be reused when common pcie code is extracted to
separate files.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In preparation to extract common PCIe driver state, indicate
PEARL-specific structures by their name and move them to pearl-specific
source file.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In preparation to extract common pcie driver state into a separate
structure, rename Pearl-specific state to qtnf_pcie_pearl_state and move
it directly to pearl-specific PCIe source file.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In preparation to extract common qtnfmac PCIe driver sources into a
separate file, move existing Pearl-specific pcie driver sources to pcie/
directory.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Firmware name is only needed at probe stage, no point in keeping it in
driver state structure.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement custom rt2800mmio flush routine and change txstatus
routine to read TX_STA_FIFO also in the tasklet.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use different tx status timeouts for normal operation and when flushing.
This increase timeout to 2s for normal operation as when there are bad
radio conditions and frames are reposted many times device can not provide
the status for quite long. With new timeout we can still get valid status
on such bad conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not check for tx status timeout everytime we perform txstatus tasklet.
Perform check once per half a second.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use usb txdone/txstatus routines (now in rt2800libc) for mmio devices.
Note this also change how we handle INT_SOURCE_CSR_TX_FIFO_STATUS
interrupt. Now it is disabled since IRQ routine till end of the txstatus
tasklet (the same behaviour like others interrupts). Reason to do not
disable this interrupt was not to miss any tx status from 16 entries
FIFO register. Now, since we check for tx status timeout, we can
allow to miss some tx statuses. However this will be improved in further
patch where I also implement read status FIFO register in the tasklet.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In order to reuse usb txdone/txstatus routines for mmio, move them
to common rt2800lib.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_PCI;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_USB;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN;
~ ^~~~~~~~~~~~~~~~
3 warnings generated.
Use the values from the correct enumerated type, wifionly_chip_interface.
BTC_INTF_UNKNOWN = WIFIONLY_INTF_UNKNOWN = 0
BTC_INTF_PCI = WIFIONLY_INTF_PCI = 1
BTC_INTF_USB = WIFIONLY_INTF_USB = 2
Link: https://github.com/ClangBuiltLinux/linux/issues/135
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/wireless/ath/ath5k/debug.c:1031:14: warning: address of
array 'ah->sbands' will always evaluate to 'true'
[-Wpointer-bool-conversion]
BUG_ON(!ah->sbands);
~~~~~^~~~~~
./include/asm-generic/bug.h:61:45: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~
./include/linux/compiler.h:77:42: note: expanded from macro 'unlikely'
# define unlikely(x) __builtin_expect(!!(x), 0)
^
1 warning generated.
Given that this condition is always false because of the logical not,
just remove it.
Link: https://github.com/ClangBuiltLinux/linux/issues/130
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/net/wireless/rsi/rsi_91x_mac80211.c:927:50: warning: address of
array 'key->key' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (vif->type == NL80211_IFTYPE_STATION && key->key &&
~~ ~~~~~^~~
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/136
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: remove
extraneous parentheses around the comparison to silence this warning
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~ ^ ~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: use '=' to
turn this equality comparison into an assignment
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/134
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/pm.c: In function 'wil_suspend_keep_radio_on':
drivers/net/wireless/ath/wil6210/pm.c:193:16: warning:
variable 'start' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
'fops_dump_nfcal' is not used since commit 4447d815fd0f ("ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Let user can reset station airtime status by debugfs, it will
reset all airtime deficit to ATH_AIRTIME_QUANTUM and reset rx/tx
airtime accumulate to 0.
Signed-off-by: Louie Lu <git@louie.lu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
CE buffers are cleaned up prior to napi disable and this is causing
NULL pointer dereference due to "use after free".
Disable napi before resource cleanup to avoid "use after free".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is unbalanced napi_{enable,disable}() behavior as they
are being called from hif_snoc_{power_up/stop).
The fix is to call napi_enable() from ath10k_snoc_hif_start()
so that it matches with napi_disable() being called from
ath10k_snoc_hif_stop().
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the latest firmware design, the beacon interval should be
greater than 100 to bring the multiple vaps.
Set beacon_int_min_gcd to 100, when the wmi service
WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled
in the firmware. If not, beacon_int_min_gcd will be set
to the default value 1.
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015
Tested in QCA9888 with firmware ver 10.4-3.5.1-0005
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
remove duplicated include from ath10k driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Chipsets Tested : QCA988X, QCA9887, QCA9984
FW Tested : 10.2.4-1.0-41, 10.4-3.6.104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
>From commit "ath10k: add per target config of max_num_peers",
the num_peers value in struct ath10k_hw_params is used to override
the value obtained from the WMI op version in the firmware file.
Currently, only high latency devices (USB and SDIO) need to use this
value, since the value obtained from the WMI op version is not
applicable for these devices.
Many devices in ath10k_hw_params_list have the wrong value set.
An example of this is the QCA9880 hw2.0 chipset that had (before this
patch) num_peers set to TARGET_TLV_NUM_PEERS although the firmware
uses WMI version ATH10K_FW_WMI_OP_VERSION_10_2_4.
Using the wrong value for the QCA9880 chip results in a fw crash:
ath10k_pci 0000:01:00.0: firmware crashed! (guid ddf39880-3e64-4edf-b4e4-979d31724503)
ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 0
ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
ath10k_pci 0000:01:00.0: htt-ver 0.0 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
ath10k_pci 0000:01:00.0: firmware register dump:
ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3 0x009B54B7 0x00955B31
ath10k_pci 0000:01:00.0: [04]: 0x009B54B7 0x00060530 0x00000011 0x00400000
ath10k_pci 0000:01:00.0: [08]: 0x000001B8 0x00000007 0x00443138 0x00955A00
ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000 0x009B548E 0x009B54AB
ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000
ath10k_pci 0000:01:00.0: [20]: 0x409B54B7 0x0040AC64 0x00400000 0x00000087
ath10k_pci 0000:01:00.0: [24]: 0x809A3831 0x0040ACC4 0x000001B1 0xC09B54B7
ath10k_pci 0000:01:00.0: [28]: 0x809A2F08 0x0040AD04 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [32]: 0x80988856 0x0040AD24 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [36]: 0x8098AF64 0x0040AD44 0x00410410 0x00000001
ath10k_pci 0000:01:00.0: [40]: 0x809B5DEC 0x0040AD84 0x00410410 0x00410FF4
ath10k_pci 0000:01:00.0: [44]: 0x809B1F20 0x0040ADA4 0x00400000 0x00416C54
ath10k_pci 0000:01:00.0: [48]: 0x809C0295 0x0040ADE4 0x0040AE08 0x00411DC8
ath10k_pci 0000:01:00.0: [52]: 0x809486FA 0x0040AE04 0x00000001 0x00000000
ath10k_pci 0000:01:00.0: [56]: 0x80948E2C 0x0040AEA4 0x0041F290 0x004123D4
ath10k_pci 0000:01:00.0: Copy Engine register dump:
ath10k_pci 0000:01:00.0: [00]: 0x00057400 10 10 3 3
ath10k_pci 0000:01:00.0: [01]: 0x00057800 3 3 8 9
ath10k_pci 0000:01:00.0: [02]: 0x00057c00 2 2 1 2
ath10k_pci 0000:01:00.0: [03]: 0x00058000 1 1 2 1
ath10k_pci 0000:01:00.0: [04]: 0x00058400 0 0 40 0
ath10k_pci 0000:01:00.0: [05]: 0x00058800 1 1 0 1
ath10k_pci 0000:01:00.0: [06]: 0x00058c00 0 0 0 0
ath10k_pci 0000:01:00.0: [07]: 0x00059000 0 0 0 0
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The hw_params value will only be used if it was explicitly set in the
global hw_params array.
This makes it possible to have the num_peers member unset.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
