summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/mediatek/mt76/mt76x0
AgeCommit message (Collapse)AuthorFilesLines
2019-03-19mt76x02: do not enable RTS/CTS by defaultStanislaw Gruszka1-1/+1
My commit 26a7b5473191 ("mt76x02: set protection according to ht operation element") enabled by default RTS/CTS protection for OFDM and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non 0xffff by initvals and .set_rts_threshold callback is not called by mac80211 on initialization, only on user request or during ieee80211_reconfig() (suspend/resuem or restart_hw). Enabling RTS/CTS cause some problems when sending probe request frames by hcxdumptool penetration tool, but I expect it can cause other issues on different scenarios. Restore previous setting of RTS/CTS being disabled by default for OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff. Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-03-19mt76x02u: check chip version on probeStanislaw Gruszka1-3/+7
Since some USB device IDs are duplicated between mt76x0u, mt7601u and mt76x2u device, check chip version on probe and return error if not match the driver. Don't think this is serious issue, probe most likely will fail at some other point for wrong device, but we do not have to configure it if we know is not our device. Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26mt76usb: remove usb_mcu.cStanislaw Gruszka1-5/+0
Don't need separate file just for kmalloc/kfree. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-26mt76usb: use synchronous msg for mcu command responsesStanislaw Gruszka1-11/+0
Use usb_bulk_msg for reading MCU command responses. This simplify code a lot. Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used for reads") it also fix possible problems with rx data buffers not being aligned and contained within single page. After doing page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-26mt76: mt76x02: fix ED/CCA enabling/disablingFelix Fietkau3-5/+5
ED/CCA needs to be disable before stopping the MAC to avoid hangs from tx being blocked. It must only be enabled again after the MAC has been started again. In many places this wasn't done properly, so fix this by always clearing the relevant ED/CCA bits in mt76x2_mac_stop and set it up again after channel change or calibration is done Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76: usb: move mt76u_check_sg in usb.cLorenzo Bianconi1-1/+1
Move mt76u_check_sg routine in usb.c and introduce sg_en variable in mt76_usb in order to check if scatter-gather is supported by mt76u layer Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76x0: init: introduce mt76x0_init_txpower routineLorenzo Bianconi4-11/+39
Add mt76x0_init_txpower in order to initialize max_power per channel at device bootstrap. Modify mt76x0_get_tx_power_per_rate and mt76x0_get_power_info signature in order to compute tx power for non-operating channels Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76x0: phy: report target_power in debugfsLorenzo Bianconi1-0/+1
Initialize target_power variable in mt76x0_phy_set_txpower in order to report target_power in debugfs Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76x0: remove mt76x0u_alloc_device routineLorenzo Bianconi4-38/+24
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device. Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76: move alloc_device common code in mt76_alloc_deviceLorenzo Bianconi1-4/+1
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76: run MAC work every 100msFelix Fietkau2-2/+2
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid triggering too late and keeping tx blocking on for too long Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76: explicitly disable energy detect cca during scanFelix Fietkau1-2/+4
Avoid reusing the previous channel's tx blocking state Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76x0: mcu: remove useless commented configurationLorenzo Bianconi1-6/+0
Remove useless commented out configuration in mt76x0u_load_firmware routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-18mt76x0: eeprom: fix VHT mcs{8,9} rate power offsetLorenzo Bianconi1-3/+3
Fix rate power configuration for VHT mcs 8 and 9 in mt76x0_get_tx_power_per_rate. Moreover use the rate power offset used for HT/VHT mcs 6 even for HT/VHT mcs 7 Fixes: b37bbc8c8251 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers.gitKalle Valo4-44/+54
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on commit d04ca383860b ("mt76x0u: fix suspend/resume"), so merge wireless-drivers into wireless-drivers-next to get that.
2019-02-07mt76x0u: fix suspend/resumeStanislaw Gruszka1-17/+29
We need to reset MCU and do other initializations on resume otherwise MT7610U device will fail to initialize, what cause system hung due to USB requests timeouts. Patch fixes 4.19 -> 4.20 regression. Cc: stable@vger.kernel.org # 4.20+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-31mt76x0: eeprom: fix chan_vs_power map in mt76x0_get_power_infoLorenzo Bianconi3-27/+25
Report correct eeprom per channel power value. Fix chan_vs_power map in mt76x0_get_power_info routine Fixes: f2a2e819d672 ("mt76x0: remove eeprom dependency from mt76x0_get_power_info") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-01-17mt76: move mt76x02_phy_get_min_avg_rssi to mt76 coreFelix Fietkau1-1/+3
This will be used by mt7603 as well Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-17mt76: move mt76x02_get_txpower to mt76 coreFelix Fietkau2-2/+2
It will be reused by mt7603 later Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-11mt76: add energy detect CCA support to mt76x{0,2}e driversLorenzo Bianconi2-0/+3
Ported from the reference driver. Should fix compliance with ETSI regulatories on preventing transmission while energy detect values are above the threshold. The code has been tested using an ath9k device running tx99 as noise generator Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-11mt76x0: configure MT_VHT_HT_FBK_CFG1Stanislaw Gruszka1-0/+1
Configure MT_VHT_HT_FBK_CFG1 values similar like vendor driver. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-11mt76x0: pci: fix ACS supportLorenzo Bianconi1-0/+8
Fix Automatic Channel Selection (ACS) support in mt76x0e driver configuring properly MT_CH_TIME_CFG register Fixes: 6250318694ca ("mt76x0: pci: add get_survey support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-11mt76: Add missing include of linux/module.hHauke Mehrtens1-0/+1
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h, but this header file is not directly included. This causes problems in backports with some kernel versions. Add the missing include. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: replace sta_add/remove ops with common sta_state functionFelix Fietkau2-4/+6
Allows adding unassociated stations from mac80211 Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-30mt76: remove wait argument from mt76x02_mcu_calibrateStanislaw Gruszka1-8/+6
We always wait for CMD_CALIBRATION_OP mcu message, but wait argument is used for do additional MT_MCU_COM_REG0 register operations, which are needed for mt76x2e devices and we can use appropriate check instead of wait argument. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: introduce mt76x02_config_mac_addr_list routineLorenzo Bianconi1-0/+2
Add mt76x02_config_mac_addr_list routine in order to set the mac address list supported by the driver. Initialize wiphy->addresses/n_addresses for mt76x0e driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x02: assure we update gain after scanStanislaw Gruszka1-1/+2
Assure that after we initialize dev->cal.low_gain to -1 this will cause update gain calibration. Otherwise this might or might not happen depending on value of second bit of low_gain and values read from registers in mt76x02_phy_adjust_vga_gain(). Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x02: run calibration after scanningStanislaw Gruszka1-1/+1
If we are associated and scanning is performed, sw_scan_complete callback is done after we get back to operating channel, so we do not perform queue cal work. Fix this queue cal work from sw_scan_complete(). On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after scanning, as it was multiple times modified by channel switch code. So queue cal work without any delay to set AGC gain value. Similar like in mt76x2 init AGC gain only when set operating channel and just check before queuing cal work in sw_scan_complete() if initialization was already done. Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: remove wait argument from mt76x02_mcu_function_selectStanislaw Gruszka2-2/+2
Remove wait argument from mt76x02_mcu_function_select and wait for response when function is not Q_SELECT, what is the same behaviour like in vendor driver. Note this change behaviour for PCIe devices for Q_SELECT function form wait to no-wait, and for mt76x0u BW_SETTING from no-wait to wait. But the change is in align with vendor driver. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: remove mcu_msg_allocStanislaw Gruszka1-1/+0
We almost always use patter like this: skb = mt76_mcu_msg_alloc(dev, &msg, sizeof(msg)); return mt76_mcu_send_msg(dev, skb, CMD_FUN_SET_OP, wait_resp); This is not needed, we can allocate skb in mcu_send_msg routine. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: use band parameter for LC calibrationStanislaw Gruszka1-2/+3
We use always 1 as band parameter for MCU_CAL_LC, this break 2GHz, we should use 0 for this band instead. Patch fixes problems happened sometimes when try to associate with 2GHz AP and manifest by errors like below: [14680.920823] wlan0: authenticate with 18:31:bf:c0:51:b0 [14681.109506] wlan0: send auth to 18:31:bf:c0:51:b0 (try 1/3) [14681.310454] wlan0: send auth to 18:31:bf:c0:51:b0 (try 2/3) [14681.518469] wlan0: send auth to 18:31:bf:c0:51:b0 (try 3/3) [14681.726499] wlan0: authentication with 18:31:bf:c0:51:b0 timed out Fixes: 9aec146d0f6b ("mt76x0: pci: introduce mt76x0_phy_calirate routine") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: use tssi reported value to configure tx power if availableLorenzo Bianconi2-5/+17
Use tssi calibrated value to configure tx power gain if tssi is enabled in eeprom data Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: introduce tssi calibration supportLorenzo Bianconi1-3/+352
Run mt76x0 tssi calibration process if enabled in eeprom data. Perform calibration procedure every 4s Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: init: use mt76x02_mac_wcid_setup for wcid configurationLorenzo Bianconi1-43/+2
Use mt76x02_mac_wcid_setup utility routine for wcid init configuration and remove duplicated code. This patch fixes a mt76x0 AP issue since hw key table selection was set to pairwise by default Fixes: dbad2adcb2c7 ("mt76x0: pci: enable AP support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: init: use mt76x02_mac_shared_key_setup in mt76x0_init_hardwareLorenzo Bianconi1-9/+4
Use mt76x02_mac_shared_key_setup utility routine for shared key initialization and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: phy: use mt76_poll_msec in mt76x0_phy_temp_sensorLorenzo Bianconi1-2/+1
Use mt76_poll_msec utility routine for CORE_R34 register polling instead of mt76_poll in order to allow the hw to complete requested calibration since on slow devices (e.g. mt7620 based boards) calibration takes longer than 2ms Fixes: 66a34c66e0cb ("mt76x0: phy: add phy/vco temperature compensation") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: do not overwrite other MT_BBP(AGC, 8) fieldsStanislaw Gruszka1-3/+1
MT_BBP(AGC, 8) register has values depend on band in mt76x0_bbp_switch_tab, so we should not overwrite other fields than MT_BBP_AGC_GAIN when setting gain. This can fix performance issues when connecting to 2.4GHz AP. Fixes: 4636a2544c3b ("mt76x0: phy: align channel gain logic to mt76x2 one") Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: add DFS supportLorenzo Bianconi2-2/+13
Introduce dfs support in mt76x0e driver and unlock radar channels Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_bss_info_changed in mt76x02-lib moduleLorenzo Bianconi4-54/+2
Unify drv_bss_info_changed mac80211 callback and remove duplicated code in mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move tx protection routines in mt76x02-lib moduleLorenzo Bianconi6-99/+3
Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection routines in mt76x02-lib module and remove duplicated code in mt76x0 and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are empty files Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: update init vals for MT_TX_PROT registersLorenzo Bianconi1-6/+9
Add missing VHT MT_TX_PROT register init values Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_set_tx_ackto in mt76x02-lib moduleLorenzo Bianconi2-2/+3
Move mt76x02_set_tx_ackto and mt76x02_set_coverage_class routines in mt76x02-lib module in order to be reused by mt76x0 driver. This is a preliminary patch to unify drv_bss_info_changed mac80211 callback between mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: enable AP supportLorenzo Bianconi4-39/+32
Add missing mac80211 callbacks to mt76x0e_ops data structure and add mt76x02_beacon utility routines in mt76x0_bss_info_changed in order to enable/disable beacon transmission Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: introduce mt76x02_init_beacon_config routineLorenzo Bianconi1-7/+1
Add mt76x02_init_beacon_config utility routine in mt76x02-lib module in order to be reused by mt76x0 driver configuring BSSID registers and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_sta_ps in mt76x02-lib moduleLorenzo Bianconi1-0/+1
Move mt76x02_sta_ps utility routine in mt76x02_util.c in order to be reused by mt76x0 driver adding AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_get_txpower in mt76x02_util.cLorenzo Bianconi2-0/+2
Move mt76x02_get_txpower utility routine in mt76x02-lib module in order to be reused by mt76x0 and mt76x2u drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_sw_scan and mt76x02_sw_scan_complete in mt76x02-lib moduleLorenzo Bianconi4-26/+4
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers and remove duplicated code Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76x0: pci: add pre_tbtt_tasklet supportLorenzo Bianconi2-0/+3
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order to add AP support Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_init_device in mt76x02-lib moduleLorenzo Bianconi2-35/+3
Move mt76x02_init_device routine in mt76x02_util.c in order to be reused by mt76x0 driver and remove duplicated code. Move interface combo definition supported by the driver in mt76x02_init_device routine Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-30mt76: move mt76x02_mac_set_short_preamble in mt76x02_mac.cLorenzo Bianconi3-10/+1
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module since it is shared between mt76x0 and mt76x2 drivers Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-22 14:21:42 +0300