| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 7a21b1d4a728a483f07c638ccd8610d4b4f12684 ]
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8745f12a6600dd9d31122588621d4c8ddb332cd7 ]
Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b13f43a48571f0cd0fda271b5046b65f1f268db5 upstream.
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This name was missing in the list.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded. Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.
Remove this unnecessary differentiation and do some other small
clean-ups while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.
Fixes: 503ab8c56ca0 ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
During init, the FW checks whether the FSEQ value matches what it
expects. If it doesn't match, we print a warning to let integrators
clearly know that something is wrong. This can happen if another core
(i.e. not WiFi) has updated the FSEQ version. This notification is
only sent by the FW in production, for development firmwares, an
assertion is triggered instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
|
|
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The API has changed - update the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae8d ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In commit b93b1fe3b532 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b532 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This new API allows flushing queues based on station ID and TID in A000
devices. One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This function just calls kfree(), so it only obscures the code without
bringing any benefits. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.
Note: This fix is only for DRAM collection mode.
For other modes, an additional fix will be
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
|
|
Add two new device families to differentiate them from 8000.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.
Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.
Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
recording)
For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This API replaces the complex NVM parsing of the iwlwifi module.
Instead, we get all needed data from firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Most of the fields aren't needed in new TX path.
Enlarging the struct to 512 queues will consume a lot of memory.
Remove all references to the struct in the new TX path.
Move mac80211 queue mapping outside, since it will be needed per
queue for TVQM mode.
Add warning in paths that shouldn't be hit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we load firmware in extended mode (as we do by default for
now) driver should send a command what kind of commands ucode
should stop and wait for before proceeding with phy calibrations.
Support this command. Currently we only do NVM access - so mark
this bit only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
To utilize the maximum allowed tx power, an additional table was added
to the BIOS. The table consists of up to seven different regions
(currently only three are in use). Each region contains per band:
1. Maximum allowed tx power on the band.
2. Tx power offset for chain A.
3. Tx power offset for chain B.
On init flow driver reads this table by means of ACPI and
passes it to the firmware with GEO_TX_POWER_LIMIT cmd.
The firmware will use this table to enhance tx power with
the offset in the relevant table as well as verifying it does not
violate the maximum allowed tx power.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case of a MFUART assert, get a notification from the fw
that consists of the assert id and debug data.
The notification may be divided to multiple chunks, depending
on the size of the debug data sent to the driver, which would
be up to 1KB.
Get the notification, and if the debug info flag is enabled,
print the debug data to the dmesg.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In a000 devices FW will assign the queue number. Prepare for
that by getting rid of static defines and store them in variables.
Enlarge to u16 since we may have up to 512 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This will allow to print the name of the commands in the
logs when we sent it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using RSS on 9000 series devices, we can't rely on processing the
received frames for station powersave handling, since they could be
processed on different CPUs and out of order.
In order to still manage the powersave of stations, the firmware sends
a notification on sleep->wake, wake->sleep and - for U-APSD - frames
received with PM while already sleeping (with the TID.)
With this, the driver can set AP_LINK_PS, which is required for real
parallel RX. In addition, this requires checking for PS-Poll frames
and calling ieee80211_sta_pspoll() appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.
Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is never really used anymore.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently it is logged as UNKNOWN.
Also, 0x6c seems to be the permanent ID for this command, remove
incorrect comment and uncomment the command from the commands
list.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
