| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
ath10k_pci 0000:01:00.0: wmi command 20486 timeout, restarting hardware
ath10k_pci 0000:01:00.0: already restarting
ath10k_pci 0000:01:00.0: failed to stop WMI vdev 0: -11
ath10k_pci 0000:01:00.0: failed to stop vdev 0: -11
ieee80211 phy0: PM: **** DPM device timeout ****
Call Trace:
panic+0x125/0x315
dpm_watchdog_set+0x54/0x54
dpm_watchdog_handler+0x57/0x57
call_timer_fn+0x31/0x13c
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623022731.509-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
interface creation
During interface creation, following print is observed on the console -
Timeout while waiting for regulatory update
This occurs due to commit 906619a00967 ("wifi: ath12k: handle regulatory
hints during mac registration"), which introduced a completion mechanism to
synchronize the regulatory update process. The intent behind this change is
to coordinate the timing between when the firmware sends regulatory data to
the driver and when the driver processes that data.
However, during interface addition, if the 6 GHz band is active, the driver
invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode
regulatory settings. At this point, there is no interaction with the
firmware, so the completion object is not reinitialized. As a result,
wait_for_completion() eventually times out, leading to the observed error
log message.
Hence to fix this, move all complete() on regd_update_completed to
complete_all().
The complete() function signals only once, causing any subsequent waits
without reinitialization to timeout. In this scenario, since waiting is
unnecessary, complete_all() can be used instead, ensuring that subsequent
calls to wait without reinitialization will simply bail out and not
actually wait. This approach is ideal because if the firmware is not
involved, there is no need to wait for the completion event. However, if
the firmware is involved, it is guaranteed that the completion will be
reinitialized, and thus, it would wait.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-by: Kang Yang <kang.yang@oss.qualcomm.com>
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 906619a00967 ("wifi: ath12k: handle regulatory hints during mac registration")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250626-fix_timeout_during_interface_creation-v1-1-90a7fdc222d4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Fix misspelling reported by codespell.
Signed-off-by: Sumanth Gavini <sumanth.gavini@yahoo.com>
Link: https://patch.msgid.link/20250522205701.393612-1-sumanth.gavini@yahoo.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Fix "trasmitting" to "transmitting"
Signed-off-by: Sumanth Gavini <sumanth.gavini@yahoo.com>
Link: https://patch.msgid.link/20250521055411.288724-1-sumanth.gavini@yahoo.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Fix "busses" to "buses"
Fix "Measurments" to "Measurements"
Signed-off-by: Sumanth Gavini <sumanth.gavini@yahoo.com>
Link: https://patch.msgid.link/20250521053323.284845-1-sumanth.gavini@yahoo.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request RTT stats from firmware through HTT stats type 65
and 66. HTT stats type 65 support RTT response stats, RTT hardware stats,
RTT to-be-read self-generated stats and RTT command-result stats and HTT
stats type 66 support RTT initiator stats and RTT hardware stats. These
stats give information about number of scheduled commands, responder
allocation and termination count, initiator termination count, PASN
authentication drop and receive counts, etc.
Note: WCN firmware version -
WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support
tags HTT_STATS_PDEV_RTT_RESP_STATS_TAG(194),
HTT_STATS_PDEV_RTT_INIT_STATS_TAG(195),
HTT_STATS_PDEV_RTT_HW_STATS_TAG(196),
HTT_STATS_PDEV_RTT_TBR_SELFGEN_QUEUED_STATS_TAG(197) and
HTT_STATS_PDEV_RTT_TBR_CMD_RESULT_STATS_TAG(198), currently.
Sample output:
echo 65 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_PDEV_RTT_RESP_STATS_TLV:
pdev_id = 0
tx_11mc_ftm_suc = 0
tx_11mc_ftm_suc_retry = 0
tx_11mc_ftm_fail = 0
.....
HTT_STATS_PDEV_RTT_HW_STATS_TAG:
ista_ranging_ndpa_cnt = 0
ista_ranging_ndp_cnt = 0
ista_ranging_i2r_lmr_cnt = 0
rtsa_ranging_resp_cnt = 0
.....
HTT_STATS_PDEV_RTT_TBR_SELFGEN_QUEUED_STATS_TAG:
SU poll = 0
SU sound = 0
.....
MU poll = 0
MU sound = 0
.....
HTT_STATS_PDEV_RTT_TBR_CMD_RESULT_STATS_TAG:
num_sch_cmd_status_0:
SU frame_SGEN_TF_POLL = 0
SU frame_SGEN_TF_SOUND = 0
SU frame_SGEN_TBR_NDPA = 0
SU frame_SGEN_TBR_NDP = 0
SU frame_SGEN_TBR_LMR = 0
SU frame_SGEN_TF_REPORT = 0
MU frame_SGEN_TF_POLL = 0
.....
echo 66 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_PDEV_RTT_INIT_STATS_TLV:
pdev_id = 0
tx_11mc_ftmr_cnt = 0
tx_11mc_ftmr_fail = 0
tx_11mc_ftmr_suc_retry = 0
rx_11mc_ftm_cnt = 0
rx_11az_ftm_cnt = 0
.....
HTT_STATS_PDEV_RTT_HW_STATS_TAG:
ista_ranging_ndpa_cnt = 0
ista_ranging_ndp_cnt = 0
ista_ranging_i2r_lmr_cnt = 0
rtsa_ranging_resp_cnt = 0
rtsa_ranging_ndp_cnt = 0
rsta_ranging_lmr_cnt = 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250617051136.264193-3-quic_rdevanat@quicinc.com
[rename enum ath12k_htt_stats_txsend_ftype_t]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support to request TDMA stats, MLO scheduled stats and MLO IPC stats
from firmware through HTT stats type 57, 63 and 64, respectively. These
stats give information about TDMA schedules, TDMA slot switches, MLO
preferred timeout, delay, MLO IPC ring count, etc.
Note: WCN firmware version -
WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support
tags HTT_STATS_PDEV_TDMA_TAG(187), HTT_STATS_MLO_SCHED_STATS_TAG(190)
and HTT_STATS_PDEV_MLO_IPC_STATS_TAG(191), currently.
Sample output:
echo 57 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_PDEV_TDMA_STATS_TLV:
mac_id = 0
num_tdma_active_schedules = 0
num_tdma_reserved_schedules = 0
num_tdma_restricted_schedules = 0
num_tdma_unconfigured_schedules = 0
num_tdma_slot_switches = 0
num_tdma_edca_switches = 0
echo 63 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_STATS_MLO_SCHED_STATS:
num_sec_link_sched = 0
num_pref_link_timeout = 0
num_pref_link_sch_delay_ipc = 0
num_pref_link_timeout_ipc = 0
echo 64 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
HTT_STATS_MLO_IPC_STATS:
src_link: 0
mlo_ipc_ring_full_cnt[0]: 0
mlo_ipc_ring_full_cnt[1]: 0
mlo_ipc_ring_full_cnt[2]: 0
mlo_ipc_ring_full_cnt[3]: 0
mlo_ipc_ring_full_cnt[4]: 0
mlo_ipc_ring_full_cnt[5]: 0
mlo_ipc_ring_full_cnt[6]: 0
src_link: 1
mlo_ipc_ring_full_cnt[0]: 0
mlo_ipc_ring_full_cnt[1]: 0
mlo_ipc_ring_full_cnt[2]: 0
mlo_ipc_ring_full_cnt[3]: 0
mlo_ipc_ring_full_cnt[4]: 0
mlo_ipc_ring_full_cnt[5]: 0
mlo_ipc_ring_full_cnt[6]: 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250617051136.264193-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add support for transmit histogram stats under HTT stats type 9. These
stats give information about drop count, MCS drop rate, histogram
count, etc.
Note: WCN7850 firmware version -
WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support tag
HTT_STATS_TX_PDEV_HISTOGRAM_STATS_TAG(144), currently.
Sample output:
echo 9 > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/mac0/htt_stats
...
low_latency_rate_cnt = 0
su_burst_rate_drop_cnt = 0
su_burst_rate_drop_fail_cnt = 0
rate_retry_mcs_drop_cnt = 0
PER_HISTOGRAM_STATS
mcs_drop_rate = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0
per_histogram_count = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0,
11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0,
21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0,
31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0, 38:0, 39:0, 40:0,
41:0, 42:0, 43:0, 44:0, 45:0, 46:0, 47:0, 48:0, 49:0, 50:0,
51:0, 52:0, 53:0, 54:0, 55:0, 56:0, 57:0, 58:0, 59:0, 60:0,
61:0, 62:0, 63:0, 64:0, 65:0, 66:0, 67:0, 68:0, 69:0, 70:0,
71:0, 72:0, 73:0, 74:0, 75:0, 76:0, 77:0, 78:0, 79:0, 80:0,
81:0, 82:0, 83:0, 84:0, 85:0, 86:0, 87:0, 88:0, 89:0, 90:0,
91:0, 92:0, 93:0, 94:0, 95:0, 96:0, 97:0, 98:0, 99:0, 100:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Saleemuddin Shaik <quic_saleemud@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250617112139.865788-1-quic_rdevanat@quicinc.com
[add __packed to struct ath12k_htt_tx_histogram_stats_tlv]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Signed-off-by: Ramasamy Kaliappan <ramasamy.kaliappan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250608145651.1735236-1-ramasamy.kaliappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The read memory barrier added by commit 6b67d2cf14ea ("wifi: ath12k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-3-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-6-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The read memory barrier added by commit ab52e3e44fe9 ("wifi: ath11k: fix
rx completion meta data corruption") is enough to guarantee ordering
also for plain descriptor accesses so drop the unnecessary READ_ONCE().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The read memory barrier added by commit 6d037a372f81 ("wifi: ath11k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-3-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The power value is 6 dBm on an AP operating on the 6 GHz channel.
This is a very low value.
On 6 GHz, the target computes the EIRP based on the power values sent
in the WMI_VDEV_SET_TPC_POWER_CMD. Currently, this is being sent only
for station interfaces and not for AP interfaces.
Therefore, add AP vdev to the condition in
ath12k_mac_station_supports_tpc() and rename
ath12k_mac_station_supports_tpc() to ath12k_mac_supports_tpc().
For a AP vdev, hardcode ap_power_type as IEEE80211_REG_LPI_AP, which is
filled in the WMI_VDEV_SET_TPC_POWER_CMDID sent to the target.
Currently, LPI is the only supported AP power mode. Since there is
no method currently to set the AP power mode from user-space, the
power mode is hard-coded to LPI.
Retain the existing logic for populating the power mode for a station
vdev.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hariharan Basuthkar <quic_hbasuthk@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606112316.39316-1-quic_hbasuthk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603063512.1887652-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, when a station is associated with a Non-Transmitting BSS of an
MBSSID set, beacons are not frequently received from the firmware. This
results in missing events via beacons, such as channel switches, leading
to the station not switching to new channel as the AP does, eventually
causing a kick out event from the firmware. This issue arises due to
missing configuration of Non-Transmitting BSS information in station's
vdev up command.
Fix this by filling information such as the Transmitting BSSID, profile index
and profile count in vdev up command of station.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ATH12K_DEFAULT_NOISE_FLOOR represents the approximate noise floor value
which is used for RSSI calculation. Commit "wifi: ath12k: handle WMI event
for real noise floor calculation" added support to get the real noise floor
value from the firmware. Add changes to use the real value now instead of
the default one.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-2-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-1-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Don't populate the read-only array svc_id on the stack at run time,
instead make it static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250619082010.1834109-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Make sure to deregister the PM notifier to avoid a use-after-free on
suspend in case core initialisation fails (e.g. due to missing
firmware).
Tested-on: WCN6855 hw2.0 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: 32d93b51bc7e ("wifi: ath11k: choose default PM policy for hibernation")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/all/d0cd065c-1cd1-4e56-8c57-60777b1f3664@oss.qualcomm.com/
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250624082022.15469-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In a number of cases we see kernel panics on resume due
to ath11k kernel page fault, which happens under the
following circumstances:
1) First ath11k_hal_dump_srng_stats() call
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 22511ms before
ath11k_pci 0000:01:00.0: group_id 1 14440788ms before
[..]
ath11k_pci 0000:01:00.0: failed to receive control response completion, polling..
ath11k_pci 0000:01:00.0: Service connect timeout
ath11k_pci 0000:01:00.0: failed to connect to HTT: -110
ath11k_pci 0000:01:00.0: failed to start core: -110
ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM
ath11k_pci 0000:01:00.0: already resetting count 2
ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110
ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110
ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery
[..]
2) At this point reconfiguration fails (we have 2 resets) and
ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit()
which destroys srng lists. However, it does not reset per-list
->initialized flag.
3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized
flag and attempts to dump srng stats:
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 66785ms before
ath11k_pci 0000:01:00.0: group_id 1 14485062ms before
ath11k_pci 0000:01:00.0: group_id 2 14485062ms before
ath11k_pci 0000:01:00.0: group_id 3 14485062ms before
ath11k_pci 0000:01:00.0: group_id 4 14780845ms before
ath11k_pci 0000:01:00.0: group_id 5 14780845ms before
ath11k_pci 0000:01:00.0: group_id 6 14485062ms before
ath11k_pci 0000:01:00.0: group_id 7 66814ms before
ath11k_pci 0000:01:00.0: group_id 8 68997ms before
ath11k_pci 0000:01:00.0: group_id 9 67588ms before
ath11k_pci 0000:01:00.0: group_id 10 69511ms before
BUG: unable to handle page fault for address: ffffa007404eb010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k]
Call Trace:
<TASK>
? __die_body+0xae/0xb0
? page_fault_oops+0x381/0x3e0
? exc_page_fault+0x69/0xa0
? asm_exc_page_fault+0x22/0x30
? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)]
ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)]
worker_thread+0x389/0x930
kthread+0x149/0x170
Clear per-list ->initialized flag in ath11k_hal_srng_deinit().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 5118935b1bc2 ("ath11k: dump SRNG stats during FW assert")
Link: https://patch.msgid.link/20250612084551.702803-1-senozhatsky@chromium.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
- ath11k/WCN6855/hw2.0/amss.bin,
ath11k/WCN6855/hw2.0/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
- ath11k/WCN6855/hw2.0/nfa765/amss.bin,
ath11k/WCN6855/hw2.0/nfa765/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
The former is the default firmware, suitable for most WiFi 6 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522013444.1301330-3-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Since 2b0996c7646 , all of this platform code became no-op with no OF
replacement. Not only that, there are no users of AHB here. Add an OF
match table that mostly mirrors the original platform device id table.
Use a qca prefix as is done for the only other property: qca,no-eeprom.
Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices
here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-5-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Alphabetic includes are easier to look at and to make further changes to
them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-3-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Easier to look at. Follows netdev style.
Also remove ret assignment. Because of all of these devm conversions,
ret = 0 is a path that never gets hit. The first time it does it when
request_irq fails, but that ends up reassigning it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-2-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.17
All ath drivers:
Add "#include <linux/export.h>" to all files that use EXPORT_SYMBOL()
to fix a newly introduced 'make W=1' check. Note that check has
subsequently been changed to only test when W=2, but keep the fixes to
suppress the warning for 'make W=2'.
ath12k:
Properly handle scan requests on multi-radio wiphy devices.
Perform the usual set of bug fixes and cleanups.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In ath12k_dp_tx_get_encap_type(), the arvif parameter is only used to
retrieve the ab pointer. In vdev delete sequence the arvif->ar could
become NULL and that would trigger kernel panic.
Since the caller ath12k_dp_tx() already has a valid ab pointer, pass it
directly to avoid panic and unnecessary dereferencing.
PC points to "ath12k_dp_tx+0x228/0x988 [ath12k]"
LR points to "ath12k_dp_tx+0xc8/0x988 [ath12k]".
The Backtrace obtained is as follows:
ath12k_dp_tx+0x228/0x988 [ath12k]
ath12k_mac_tx_check_max_limit+0x608/0x920 [ath12k]
ieee80211_process_measurement_req+0x320/0x348 [mac80211]
ieee80211_tx_dequeue+0x9ac/0x1518 [mac80211]
ieee80211_tx_dequeue+0xb14/0x1518 [mac80211]
ieee80211_tx_prepare_skb+0x224/0x254 [mac80211]
ieee80211_xmit+0xec/0x100 [mac80211]
__ieee80211_subif_start_xmit+0xc50/0xf40 [mac80211]
ieee80211_subif_start_xmit+0x2e8/0x308 [mac80211]
netdev_start_xmit+0x150/0x18c
dev_hard_start_xmit+0x74/0xc0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: e93bbd65547e ("wifi: ath12k: fix packets are sent in native wifi mode while we set raw mode")
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606044936.3989400-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the budget for monitor ring is reduced during each ring entry
reaping and again when the end reason is HAL_MON_END_OF_PPDU, leading to
inefficient budget use. The below mentioned commit intended to decrement
the budget only for HAL_MON_END_OF_PPDU but did not remove the other
decrement. Fix this by eliminating the budget decrement for each ring entry
reaping, ensuring the driver always reaps one full PPDU worth of entries
from the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 394a3fa7c538 ("wifi: ath12k: Optimize NAPI budget by adjusting PPDU processing")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603103542.1164713-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The commit 89ac53e96217 ("wifi: ath12k: Enable REO queue lookup table
feature on QCN9274") originally intended to enable the reoq_lut_support
hardware parameter flag for both QCN9274 hw1.0 and hw2.0. However,
it enabled it only for QCN9274 hw1.0.
Hence, enable REO queue lookup table feature on QCN9274 hw2.0.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250609-qcn9274-reoq-v1-1-a92c91abc9b9@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/ath12k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-5-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath11k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debugfs.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/dp.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/fw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/hal.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/pcic.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/qmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-4-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath10k/bmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htc.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_rx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_tx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/mac.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-3-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath9k/common-beacon.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-init.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-spectral.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/dynack.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/hw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-2-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Commit a934a57a42f6 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/main.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-1-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, TID is not decremented before peer cleanup, during error
handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to
out-of-bounds access in peer->rx_tid[].
Hence, add a decrement operation for TID, before peer cleanup to
ensures proper cleanup and prevents out-of-bounds access issues when
the RX peer frag setup fails.
Found during code review. Compile tested only.
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250526034713.712592-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath12k_dp_rx_deliver_msdu() currently includes logic related to
monitor mode handling. This code was inherited from the ath11k driver,
where a single rx handler was used for both regular and monitor mode
packets. In ath12k, however, monitor mode packets are handled separately
via ath12k_dp_mon_rx_deliver_msdu(), which contains all the necessary
monitor-specific logic. Therefore, monitor-related checks and operations
in ath12k_dp_rx_deliver_msdu() are no longer needed. Remove this dead code
to simplify the rx path and avoid unnecessary per-packet checks.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605054438.1855365-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
As station, WCN7850 firmware requires pairwise key to be installed before
group key. Currently host does not care about this, so it is up to kernel
or userspace to decide which one will be installed first. In case above
requirement is not met, WCN7850 firmware's EAPOL station machine is messed
up, and finally connection fails [1].
Reorder key install for station interface in that case: this is done by
caching group key first; Later when pairwise key arrives, both can be
installed in required order.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218733
Link: https://lore.kernel.org/all/AS8P190MB12051DDBD84CD88E71C40AD7873F2@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-2-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
WMI_KEY_PAIRWISE and WMI_KEY_GROUP are not bit fields, change
bit operation to direct assignment to avoid confusion.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-1-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
If a regulatory notification is there in the system while the hardware is
being registered, it attempts to set the new regulatory country. However,
ath12k currently boots with a default country derived from the BDF. If this
default country differs from the one provided in the notification, a race
condition can occur while updating the regulatory information back to
userspace. This potentially leads to driver having the incorrect regulatory
applied.
For example, suppose the regulatory domain for France (FR) is already
applied, and then the driver is loaded with a BDF that has the United
States (US) country programmed. When the driver finishes loading, the
regulatory domain shown in phyX still reflects the US regulatory settings.
This is incorrect, as the driver had already received a notification for
FR during hardware registration, but failed to process it properly due to
the race condition.
The race condition exists during driver initialization and hardware
registration:
- On driver load, the firmware sends BDF-based country regulatory rules,
which are stored in default_regd via ath12k_reg_handle_chan_list().
- During hardware registration, a regulatory notification is triggered
through:
ath12k_mac_hw_register()
-> ieee80211_register_hw()
-> wiphy_register()
-> wiphy_regulatory_register()
-> reg_call_notifier()
This sends a country code to the firmware, which responds with updated
regulatory rules.
- After registration, ath12k_mac_hw_register() calls ath12k_regd_update(),
which copies default_regd and passes it to the upper layers.
The race occurs between the firmware's response and the execution of
ath12k_regd_update(). If the firmware's new rules are processed before the
update call, the correct values are used. Otherwise, outdated boot-time
country settings are exposed to userspace.
To resolve this issue, introduce a completion mechanism within the hardware
group (ah). Trigger this completion whenever a regulatory change is
requested from the firmware. Then, in ath12k_regd_update(), wait for the
firmware to complete its regulatory processing before proceeding with the
update.
This ensures that during driver load, the default country is processed
first. However, before ath12k_regd_update() is called, the new regulatory
notification will have already been received by the driver. As a result, it
will wait for the firmware's regulatory processing to complete, and only
the final, correct regulatory domain will be updated to userspace.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250617-handle_user_regd_update_hints_during_insmod-v2-1-10a6a48efe81@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
With previous patch [1], ath12k_reg_update_chan_list() will be called
during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath12k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called with the rtnl_lock held.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: f335295aa29c ("wifi: ath12k: avoid deadlock during regulatory update in ath12k_regd_update()") #[1]
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605082528.701-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices that support overlapping frequency ranges within
the same band are grouped into an ath12k hardware (HW) setup, they share a
common wiphy instance. Consequently, the channel list (wiphy->bands[])
becomes unified across all associated radios (ar).
For reference, the devices are:
2.4 GHz + 5 GHz Low Band
5 GHz High Band + 6 GHz
The first radio probed within the 5 GHz range (say 5 GHz Low Band) updates
its sband reference (&ar->mac.sbands[NL80211_BAND_5GHZ]) within
wiphy->bands[]. However, when the second 5 GHz radio (5 GHz High Band) is
probed, it replaces the existing wiphy->bands[] entry with its own sub-band
reference. As a result, wiphy->bands[] always reflects the channel list
from the most recently probed radio in that band, restricting supported
channels to those within its specific range for upper-layer.
Fix this by updating the wiphy->bands[] to just enable the channels of
current radio when there exist a radio which already has set it.
This will make sure wiphy->bands[] holds reference of first radio which
got probed in 5 GHz band and subsequent radio just updates the channel list
in the same address space.
Since same sband memory space is shared between radios of a band, while
determining the allowed frequency range of radio, its frequency limits
(ar->freq_range.start_freq, end_freq) should be used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522111514.3735107-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices having supported frequency range in same band
(as mentioned below) are combined into an ath12k HW group, they will be
part of same wiphy and hence the channel list (wiphy->bands[]) will be
common for all of the radios (ar).
1 - 2.4 GHz + 5 GHz Low band
2 - 5 GHz High band + 6 GHz
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with both the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan as some frequencies in the scan
request are not supported, resulting is scan failure.
Fix this by splitting the scan request into multiples scans in driver
based on the supported frequency range of different radios in a band and
schedule scans in parallel to them.
Finally send scan completion/abort notification to mac80211 after all the
radios complete their scheduled scan.
Also, last_scan_link is not needed anymore as ath12k internally schedules
multiple scans, remove the same and use ahvif->links_map to identify
scan links when scan is cancelled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Co-developed-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
When two split-phy devices that support overlapping frequency ranges within
the same band(say 5 GHz low and 5 GHz high) are grouped into an ath12k
hardware (HW) setup, they share a common wiphy instance. Consequently, the
channel list (wiphy->bands[]) becomes unified across all associated
radios (ar).
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with all the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan since some of the frequencies in
the scan request are not supported, resulting in a scan failure.
To fix this ath12k driver should split the scan request into multiple
scans based on requested frequencies and schedule them to corresponding
underlying radio(s) in parallel.
Currently, ath12k driver assigns the scan link (link 15) in ahvif->links[]
for scan vdev creation. However, with parallel scan support being
introduced in the following patch, multiple radios (e.g., 5 GHz low and
5 GHz high) in the same HW group may attempt to use the same scan link
concurrently, causing conflicts where the vdev created by one radio could
be deleted and re-initialized by another.
To address this, reserve space for additional scan links for each radio in
a MLO group and allow subsequent radios to use different available scan
links (ahvif->link[15..MAX_SCAN_LINKS]) when scan link (15) is
pre-occupied.
While at it, rename ATH12K_DEFAULT_SCAN_LINK as ATH12K_FIRST_SCAN_LINK
as there is no longer only one scan link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
