summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wil6210
AgeCommit message (Collapse)AuthorFilesLines
2014-03-21Merge branch 'master' of ↵John W. Linville9-140/+454
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2014-03-17wil6210: fix race between disconnect and Tx NAPIVladimir Kondratiev6-4/+47
When disconnecting some CID, corresponded Tx vring get released. During vring release, all descriptors get freed. It is possible that Tx NAPI working on the same vring simultaneously. If it happens, descriptor may be double freed. To protect from the race above, make sure NAPI won't process the same vring. Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if 'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI get synchronized. NAPI enablement status protected by wil->mutex, add protection where it was missing and check for it. During reset, disconnect all peers first, then proceed with the Rx vring. It allows for the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about connection status change Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: add memory barriers for the reset flowVladimir Kondratiev1-0/+6
make sure reset flow executed in order Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: target reset flow updateVladimir Kondratiev2-6/+8
Use 'real' indication for hardware state. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: use GROVladimir Kondratiev2-8/+8
GRO is easy to enable when already using NAPI framework, and it improves CPU utilisation. Enable it by default. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: serialize fw_recovery and start_apVladimir Kondratiev2-4/+13
These methods can change device state, serialize with others similar ones like up/down Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix secondary connectVladimir Kondratiev1-0/+4
when STA receiving connect() when already connected, it should return error Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fw error recoveryVladimir Kondratiev4-1/+58
upon fw error interrupt - in STA mode, disconnect/cancel scan and then reset FW/HW added module param - no_fw_recovery which is false by default Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Fix kernel oops in reset flowVladimir Kondratiev3-4/+21
wil_reset() removes vring's At the same time NAPI may be active performing Rx/Tx completion. If this happens, Rx/Tx polling functions going to access already removed vrings Make sure NAPI is idle and won't be started prior to vring removal. For this, track NAPI enabled state Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix memory leak in the AP flowVladimir Kondratiev2-0/+7
When switching between STA and AP modes, memory allocated for Rx vring leaks This is because start_ap() allocates Rx vring but stop_ap() do not free it. Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset() Also, check double init for Rx vring and bail out with -EINVAL Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reduce printingVladimir Kondratiev1-2/+2
Convert 2 often printed messages to dynamic ones Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reset on power goodVladimir Kondratiev2-2/+8
Configure hardware to perform full reset on "power good". This mean, reset HW on system boot. This improves card stability. By default this is off. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: sort HW registers definitionsVladimir Kondratiev2-18/+19
Put all registers in order for easier navigation; fix naming to reflect hardware cluster Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix for HW bug in interrupt setup logicVladimir Kondratiev3-0/+19
Hardware bug triggered by the MSI init while INTx asserted for some reason. De-assert INTx prior to MSI set-up Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: report reset timeVladimir Kondratiev1-3/+3
Useful to detect hardware problems Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reduce dmesg pollution after FW crashVladimir Kondratiev1-1/+6
When FW crashes, dmesg get polluted with the "FW not ready" error message. Print it only once per FW lifecycle Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: update target reset to support new HWVladimir Kondratiev3-1/+34
Support for new chip revision. Revision read from the internal register, PCIE config's "revision id" register do not indicate HW version properly Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: generalize tx desc mappingVladimir Kondratiev2-27/+33
Introduce enum to describe mapping type; allow 'none' in addition to 'single' and 'page'; this is preparation for GSO Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: add scatter-gather supportVladimir Kondratiev4-67/+115
When setting fragmented skb for Tx, assign skb to the last descriptor and set number of fragments in the 1-st one On Tx complete, HW sets "DU" bit in Tx descriptor only for the last descriptor; so search for it using number of fragments field. Middle descriptors may have "DU" bit not set by the hardware. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: enable scan while connectedVladimir Kondratiev2-8/+2
New firmware do support scan while connected. Enable it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Block data till "data port open" reportedVladimir Kondratiev5-6/+38
When connection established, as reported by WMI_CONNECT_EVENTID, 4-way handshaking required for the secure connection is not done yet. It is indicated by another WMI event. Wait for it and only then allow data traffic. In case of non-secure connection, FW reports "data port open" immediately after connection. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Helpers to deal with 'cidxtid' fieldsVladimir Kondratiev2-1/+26
Encode/decode helpers Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-13Merge branch 'master' of ↵John W. Linville9-74/+874
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/ath/ath9k/recv.c
2014-03-04wil6210: fix smatch warning in wil_cfg80211_get_station()Vladimir Kondratiev1-1/+1
Smatch suggests to propagate error code from wil_find_cid(), and, indeed, it is a good idea. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-04wil6210: fix buffer overflow in wil_txdesc_debugfs_show()Vladimir Kondratiev1-6/+6
Wrong index comparison logic, found by smatch: drivers/net/wireless/ath/wil6210/debugfs.c:402 wil_txdesc_debugfs_show() warn: buffer overflow 'wil->vring_tx' 24 <= 24 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: do not reorder groupcast RxVladimir Kondratiev1-1/+7
Groupcast frames are not subject for BACK reordering because they are not ACK'ed and one can't request re-transmitt Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: single station disconnectVladimir Kondratiev4-7/+30
implement del_station() method in the struct cfg80211_ops It allows to disconnect single peer from the AP Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: use ether_addr_equalVladimir Kondratiev1-1/+2
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Provide signal strength indicationVladimir Kondratiev2-9/+10
When notifying about Rx mgmt (ex: during scan), extract signal strength reported by the hardware. signal is not MBM, it is arbitrary units 0..100 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Fill vring2cid_tid table earlyVladimir Kondratiev1-3/+3
Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID since firmware may generate events during this call; and events need translation table filled to be properly dispatched Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: disconnect only requested peerVladimir Kondratiev1-25/+56
Disconnect event reported by the FW, should lead to disconnection of only requested peer. Find for the appropriate CID and disconnect only it For AP-like interface, notify cfg80211 with del_sta(), for the client type interface, disconnect and turn link off. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: per-connection statisticsVladimir Kondratiev4-6/+77
Calculate statistics per connection, report with "iw station dump" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: dump_station initial supportVladimir Kondratiev1-16/+66
Rx stats is not calculated per STA - just give some number Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: fix BACK status processingVladimir Kondratiev1-16/+31
When FW notifies about BACK status change, it provides ring ID. Process BA status for requested connection only. As for now, FW don't report Rx BACK status, it reports Tx one instead. As per current algorithm used in the firmware, imply Rx BACK state is in sync with Tx one Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: broadcast TxVladimir Kondratiev1-10/+55
Hardware do not support "real" broadcast on the air. Use method similar to the Directed Multicast Service (DMS) as described in the 10.23.15.2 "DMS procedures" This service copies frame and delivers unicast for each associated peer Do the following: send original frame to 1-st Tx vring, and send copies to all other active vrings. As currently hardware/firmware don't support A-MSDU, convert broadcast frame to unicast instead of wrapping it in A-MSDU Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Find free vring for TxVladimir Kondratiev1-1/+12
There are 24 possible Tx vrings; when doind multiple connections, more then one vring has to be used. Search for free one and select it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Block ACKVladimir Kondratiev8-7/+290
When running multiple connections, hardware can't do BACK reordering and it should be done on the host. Model after mac80211's implementation. Drop RCU for now; to be re-added when BACK will be stabilized BACK handshaking is not implemented yet in the hardware, pretend it was done to support the way FW operating Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: multiple connect - initial supportVladimir Kondratiev6-15/+148
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections. Each connection has its own CID (connection ID) that describes chip's beam-forming entity. Tx Vring should refer to correct CID for frame to reach its destination. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: [DEBUG] Improve Vring printingVladimir Kondratiev1-5/+6
Print '_' for the 'idle' descriptors - this makes vring representation more visible. Also, for the Tx side, differentiate descriptors having associated skb's - print ones with skb as 'H' and without as 'h'. Good to represent scattered frames. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: [DEBUG] allow to query Rx and all Tx VRING descriptorsVladimir Kondratiev1-8/+32
Expand debug capabilities to query all Tx/Rx descriptors. Usefull to analyse various hardware/software stall situations. Printed is whole descriptor content and the frame itself. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28wil6210: Tx management frameVladimir Kondratiev3-0/+105
Implement management frame passing. In order to receive frame on the other side, remain_on_channel() should be implemented as well Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-19wil6210: Use pci_enable_msi_range() instead of pci_enable_msi_block()Alexander Gordeev1-17/+15
As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() and pci_enable_msix_range() interfaces. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: wil6210@qca.qualcomm.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-16wil6210: correct #include for prefetch()Vladimir Kondratiev1-1/+1
This fixes bug found by the kbuild test robot: tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master head: 1e2f9295f4c657500111514f92a3d3894d0e05b4 commit: 1cbbcb08c786964a16773c39f2536f1923c73c58 [135/140] wil6210: prefetch head of packet config: make ARCH=microblaze allyesconfig All error/warnings: drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx': >> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration] prefetch(skb->data); ^ cc1: some warnings being treated as errors vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c 375 wil_err(wil, "Rx size too large: %d bytes!\n", dmalen); 376 kfree_skb(skb); 377 return NULL; 378 } 379 skb_trim(skb, dmalen); 380 > 381 prefetch(skb->data); 382 383 wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1, 384 skb->data, skb_headlen(skb), false); Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-09wil6210: prefetch head of packetVladimir Kondratiev1-0/+3
As soon as skb is ready to be reaped, prefetch 1-st cache line. This accelerates data access that is performed later, during the packet classification by the driver and IP stack. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-09wil6210: Fix IP version indication for Tx csum offloadVladimir Kondratiev1-2/+3
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4 only. Don't set it for IPv6 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-09wil6210: interrupt moderationVladimir Kondratiev2-0/+14
Use hardware capabilities to limit IRQ generation to about 15 per msec It corresponds to about 7 packets/IRQ when running iperf with default parameters at 1.3Gbps Do not enable this feature in the sniffer (monitor) mode, because interrupt moderation cause timestamp accuracy deterioration. For the sniffer flow, it is important to get precise timestamp. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-11-15tree-wide: use reinit_completion instead of INIT_COMPLETIONWolfram Sang1-1/+1
Use this new function to make code more comprehensible, since we are reinitialzing the completion, not initializing. [akpm@linux-foundation.org: linux-next resyncs] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-10-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-nextDavid S. Miller1-1/+0
Conflicts: drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h drivers/net/wireless/rtlwifi/rtl8188ee/phy.h drivers/net/wireless/rtlwifi/rtl8192ce/phy.h drivers/net/wireless/rtlwifi/rtl8192de/phy.h drivers/net/wireless/rtlwifi/rtl8723ae/phy.h Just some minor conflicts between the wireless-next changes and Joe Perches's "extern" removal from function prototypes in header files. John W. Linville says: ==================== Regarding the Bluetooth bits, Gustavo says: "The big work here is from Marcel and Johan. They did a lot of work in the L2CAP, HCI and MGMT layers. The most important ones are the addition of a new MGMT command to enable/disable LE advertisement and the introduction of the HCI user channel to allow applications to get directly and exclusive access to Bluetooth devices." As to the ath10k bits, Kalle says: "Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's just too much to support it. Michal added support for the new firmware interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are minor fixes or cleanups." And also: "Major changes are: * throughput improvements including aligning the RX frames correctly and optimising HTT layer (Michal) * remove qca98xx hw1.0 support (Bartosz) * add support for firmware version 999.999.0.636 (Michal) * firmware htt statistics support (Kalle) * fix WEP in AP and IBSS mode (Marek) * fix a mutex unlock balance in debugfs file (Shafi) And of course there's a lot of smaller fixes and cleanup." For the wl12xx bits, Luca says: "Here are some patches intended for 3.13. Eliad is upstreaming a bunch of patches that have been pending in the internal tree. Mostly bugfixes and other small improvements." Along with that... Arend and friends bring us a batch of brcmfmac updates, Larry Finger offers some rtlwifi refactoring, and Sujith sends the usual batch of ath9k updates. As usual, there are a number of other small updates from a variety of players as well. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-03net:drivers/net: Miscellaneous conversions to ETH_ALENJoe Perches1-2/+2
Convert the memset/memcpy uses of 6 to ETH_ALEN where appropriate. Also convert some struct definitions and u8 array declarations of [6] to ETH_ALEN. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-26wireless: wil6210: remove unnecessary pci_set_drvdata()Jingoo Han1-1/+0
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-03 17:30:20 +0300