| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit "ath9k: fix possible hang on flush" changed the receive code
to always link rx descriptors of processed frames, even when flushing.
In some cases, this leads to flushed rx buffers being passed to the
hardware while rx is already stopped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make DFS pulse interval calculation independent
from CONFIG_ATH9K_DEBUGFS.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it. Both
ath9k and ath10k define the callback and just returns. This commit
removes them.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
On idle state, sleep timer is scheduled to put the chip into fullsleep.
But during suspend, this timer is scheduled after the chip is moved to
fullsleep forcibily. This is causing below unnecessary error messages
in kernel log during suspend.
ath: phy2: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000
!= 0x00000000
ath: phy2: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: phy2: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
DMADBG_7=0xdeadbeef
Reported-by: Arkh4mKn1ght <arkh4mkn1ght@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The keycache index is used to abort transmission for given station
when it goes to sleep state. But the commit "ath9k_hw: Abort transmission
for sleeping station" is not handling multi-key station. Fix that.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
DFS pulse interval printing is only available
when CONFIG_ATH9K_DEBUGFS is set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Apparently Oleksij's compile testing was no better than mine initially
was... :-(
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_txrx.o
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c: In function ‘ath9k_rx_prepare’:
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:1006:2: warning: passing argument 2 of ‘ath9k_htc_err_stat_rx’ from incompatible pointer type [enabled by default]
ath9k_htc_err_stat_rx(priv, &rx_stats);
^
In file included from drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:17:0:
drivers/net/wireless/ath/ath9k/htc.h:380:20: note: expected ‘struct ath_htc_rx_status *’ but argument is of type ‘struct ath_rx_status *’
static inline void ath9k_htc_err_stat_rx(struct ath9k_htc_priv *priv,
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The data transmission to the power save station should be aborted
immediately, whenever the station informs sleep state. Right now
the frames queued into into hardware are being transmitted until
the hardware detects the power save station based excessive retries
of the data frames due to unacknowlegdement. Then remaining frames
are returned with filetered status and might be retried later by
driver or mac80211.
Per WFA certification testing, AP should not send out more than two
frames after processing nullfunc with PM bit set from associated
station. To speed up tx filtering, the pending frames in hardware
queues for given station will be aborted immediately via tx filter
registers. This transmit filters can be ignored if the descriptor
is having invalid destination index or clear destination mask set.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
and use it. This move need changes in both drivers.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
to fix compile errors
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Systems with multiple DFS channel detectors need to track
timestamp of previous pulse per instance to display the
correct pulse interval.
Since the interval value is used for debug printing only,
this is a non-functional modification.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Originally Helmut posted a v2 of the "ath9k: Allow platform override
without EEPROM override", but I had prematurely commited the original
as commit 552a515707a. This commit restores the tree to what Helmut
intended with his v2 submission. -- JWL
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* rfsat gainchange hysteresis of rf_gain stuck with large
interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
net/mac80211/chan.c
|
|
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use generic TSF timers to trigger powersave state changes based
information from the P2P NoA attribute.
Opportunistic Powersave is not handled, because the driver does not
support powersave at the moment.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Preparation for adding P2P powersave and multi-channel support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.
Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.
The same thing was proposed previously by Ben:
http://www.spinics.net/lists/linux-wireless/msg112891.html
The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a flush is requested, make sure to clear the descriptor once we've
processed it.
This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k: prepare for multi-interface CSA support" added a call to
ieee80211_iterate_active_interfaces in atomic context (beacon tasklet),
which is crashing.
Use ieee80211_iterate_active_interfaces_atomic instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use 0-8 instead of 0-16, which is closer to the old implementation.
Also drop the overwrite of the firstep_low parameter to improve
stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add DFS interface combination only when
CONFIG_ATH9K_DFS_CERTIFIED is set. In other case
user can run CAC/beaconing without proper handling
of pulse events (without radar detection activated).
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Frame aggregation requires the IEEE80211_TX_STAT_AMPDU to
be set so that mac80211 can report the last_tx_rate correctly.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
