summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath9k/hw-ops.h
AgeCommit message (Collapse)AuthorFilesLines
2015-03-20ath9k: Register private AIC opsSujith Manoharan1-0/+8
AIC can be disabled or enabled on a per-card basis using MCI configuration, so register a function to check its status. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2014-10-27ath9k: restart hardware after noise floor calibration failureFelix Fietkau1-4/+3
When NF calibration fails, the radio often becomes deaf. The usual hardware hang checks do not detect this, so it's better to issue a reset when that happens. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-30ath9k: fix getting tx duration for dynackFelix Fietkau1-0/+6
On AR9003, tx control and tx status are in separate descriptor rings. Tx duration is extracted from the tx control descriptor data, which ar9003_hw_proc_txdesc cannot access. Fix getting the duration by adding a separate callback for it. Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-04ath9k: Move private HW callbacks to hw-ops.hSujith Manoharan1-0/+27
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-04ath9k: Add HW callbacks for MAC/BB hang checksSujith Manoharan1-0/+10
This is required for adding separate hang check routines for AR9002 and AR9003. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-04ath9k: Register supported HW hang checksSujith Manoharan1-0/+5
HW hang checks have to be done on a per-chip basis. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-19ath9k: move ath9k_debug_sync_cause out of ath9k_hwFelix Fietkau1-2/+3
ath9k_hw should not depend on any ath9k data structures like ath_softc Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-18ath9k: add TX99 supportLuis R. Rodriguez1-0/+16
TX99 support enables Specific Absorption Rate (SAR) testing. SAR is the unit of measurement for the amount of radio frequency(RF) absorbed by the body when using a wireless device. The RF exposure limits used are expressed in the terms of SAR, which is a measure of the electric and magnetic field strength and power density for transmitters operating at frequencies from 300 kHz to 100 GHz. Regulatory bodies around the world require that wireless device be evaluated to meet the RF exposure limits set forth in the governmental SAR regulations. In the examples below, for more bit rate options see the iw TX bitrate setting documentation: http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates Example usage: iw phy phy0 interface add moni0 type monitor ip link set dev moni0 up iw dev moni0 set channel 36 HT40+ iw set bitrates mcs-5 4 echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99 Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-09ath9k: Fix build failureSujith Manoharan1-0/+4
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for the WLAN/BT RX diversity hooks. Reported by the kernel build testing backend. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Rename ath9k_hw_antctrl_shared_chain_lnadivSujith Manoharan1-4/+3
Use "ath9k_hw_set_bt_ant_diversity" instead. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-08ath9k_hw: use the devres API for allocationsFelix Fietkau1-16/+0
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-09-24ath9k_hw: Add a HW callback to set diversitySujith Manoharan1-0/+7
This patch adds a new callback to handle WLAN RX diversity for AR9565. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-13drivers/net: Remove boolean comparisons to true/falseJoe Perches1-1/+1
Booleans should not be compared to true or false but be directly tested or tested with !. Done via cocci script: @@ bool t; @@ - t == true + t @@ bool t; @@ - t != true + !t @@ bool t; @@ - t == false + !t @@ bool t; @@ - t != false + t Signed-off-by: Joe Perches <joe@perches.com> Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-15ath9k_hw: add DFS testing checkZefir Kurtisi1-0/+9
In order to enable DFS upstream we want to be sure DFS has been tested for each chipset. Push for public documentation of the requirements we want in place and allow for enabling each chipset through a single upstream commit. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14ath9k_hw: Improve fast channel change for AR9003 chipsRajkumar Manoharan1-0/+7
In order to reduce the overall scan time, fast channel change should be implemented properly. This patch adds fast channel change support across band switch or channel mode switch instead of doing full chip reset. During the fastcc, tx iqcal measurements are preserved and will be reloaded after successful the channel change. This patch also addressed fast channel issue where the STA can not see APs in higher than operating channel on 5GHz band after the association. Cc: Paul Stewart <pstew@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-19ath9k_hw: fix setting the hardware diversity flagFelix Fietkau1-5/+0
ath9k_hw_set_diversity is only called from init.c where it cannot affect the hardware setting because it's cleared on the next reset. Instead of using a PHY op for something that's supposed to be initialized statically, set the register value directly in the INI override function. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-17ath9k_hw: remove the old tx descriptor APIFelix Fietkau1-58/+0
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-17ath9k_hw: add a new API for setting tx descriptorsFelix Fietkau1-0/+6
Instead of using lots of different functions with long argument lists, pull all the necessary information from one struct. This makes the code easier to read and eliminates the need for copying data between multiple linked descriptors. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22ath9k: merge common ->config_pci_powersave() checksStanislaw Gruszka1-0/+3
Move common checks into wrapper function. Since ASPM can be only enabled on PCIe devices ->is_pciexpress check is unneeded. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-22ath9k: remove ->config_pci_powersave() redundant argumentStanislaw Gruszka1-3/+2
We always call ->config_pci_powersave() with both restore and power_off arguments equal to 0 or both equal to 1, so merge them into one argument. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k_hw: remove ath9k_hw_get_desc_linkFelix Fietkau1-5/+0
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19ath9k: Drag the driver to the year 2011Sujith Manoharan1-1/+1
The Times They Are a-Changin'. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-16ath9k_hw: make antenna diversity modules chip specificMohammed Shafi Shajakhan1-0/+12
this is necessary to support Antenna diversity and combining in new chip sets such as AR9485, previously Antenna diversity support is available only in AR9285 Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com> Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com> Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-05ath9k_hw: remove aggregation protection modeMohammed Shafi Shajakhan1-6/+0
when aggregation protection mode is enabled the hardware needs to send RTS/CTS for each HT frame. Currently its disabled so remove the unused call backs. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-19ath9k: fix powersave frame filtering/buffering in AP modeFelix Fietkau1-0/+5
This patch fixes a long standing issue of pending packets in the queue being sent (and retransmitted many times) to sleeping stations. This was made worse by aggregation through driver-internal retransmitting of A-MDPU subframes. Previously the hardware tx filter was cleared unconditionally for every single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT for unaggregated frames. A sta_notify driver op is added to stop aggregation for stations when they enter powersave mode. Subframes stay buffered inside the driver, to ensure that the BlockAck window keeps a sane state. Since the driver uses software aggregation, the clearing of the tx filter needs to be handled by the driver instead of mac80211 for aggregated frames. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-05ath9k: remove set11n_virtualmorefragMohammed Shafi Shajakhan1-6/+0
This does not seems to be used anywhere so remove it. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath9k_hw: remove baseband rfsilent supportFelix Fietkau1-5/+0
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to turn off based on GPIO input, however that code was hardcoded to GPIO 0 instead of ah->rfkill_gpio. Since ath9k uses software rfkill anyway, this code is completely unnecessary and should be removed in case anything else ever uses GPIO 0. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07ath9k_hw: merge ath9k_hw_ani_monitor_old and ath9k_hw_ani_monitor_newFelix Fietkau1-6/+0
After the last rounds of cleanup, these functions are now functionally equivalent and can thus be merged. Also get rid of some excessive (and redundant) debug messages. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07ath9k_hw: remove function pointer abstraction for internal ANI opsFelix Fietkau1-5/+0
The code gets more concise and readable when making the new ANI functions fall back to the old ones if ANI v2 is disabled. This also makes further code cleanup easier. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07ath9k_hw: remove code duplication in phy error counter handlingFelix Fietkau1-5/+0
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old and ath9k_hw_proc_mib_event_new). Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-07ath9k_hw: clean up calibration flagsFelix Fietkau1-6/+0
The calibration actual calibration flags are only used by the per chip family source files, so it makes more sense to define them in those files instead of globally. That way the code has to test for less flags. Also instead of using a separate callback for testing whether a particular calibration type is supported, simply adjust ah->supp_cals in the calibration init which is called right after the hardware reset, before any of the calibrations are run. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-13ath9k: merge noisefloor load implementationsFelix Fietkau1-6/+0
AR5008+ and AR9003 currently use two separate implementations of the ath9k_hw_loadnf function. There are three main differences: - PHY registers for AR9003 are different - AR9003 always uses 3 chains, earlier versions are more selective - The AR9003 variant contains a fix for NF load timeouts This patch merges the two implementations into one, storing the register array in the ath_hw struct. The fix for NF load timeouts is not just relevant for AR9003, but also important for earlier hardware, so it's better to just keep one common implementation. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-14ath9k_hw: inform ANI calibration when scanningLuis R. Rodriguez1-2/+2
The new ANI implementation will use this to skip ANI calibration upon a scan. This cannot be ported to the older ANI implementation unless default ANI values from the ANI are also used upon a scan. This is essentially what one of the things thenew ANI does. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-14ath9k_hw: allow for spliting up ANI operations by familyLuis R. Rodriguez1-0/+16
The AR9003 hardware family will use a slightly modified ANI implementation which has not yet been tested on the other hardware families. To allow for this new ANI implementation a few ANI calls need to be abstracted away. This patch just allows for each hardware family to declare their own ANI ops and annotates the current ANI implementation as old. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Define abstraction for tx desc accessVasanthakumar Thiagarajan1-0/+71
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: abstract loading noisefloorLuis R. Rodriguez1-0/+6
This is the last call on calib.c which acceses PHY stuff, with this change we calib.c is now generic between both all supported hardware families. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Abstract the routine which returns interrupt statusVasanthakumar Thiagarajan1-0/+5
Also move interrupt related code to mac.c Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: split calib code by hardware familiesLuis R. Rodriguez1-1/+27
Calibration code touches phy registers and since these change the calibration code needs to be abstracted. Noise floor calibration is the only thing remaining but since the remaining calls only touch the AR_PHY_AGC_CONTROL register we'll just define that register conditionally, that will be done separately. The goal is to remove the dependency of ar9002_phy.h on calib.c This also adds stubs to be filled for AR9003 calibration code. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Split out the function for reading the noise floorFelix Fietkau1-0/+6
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Add abstraction to set/get link pointerVasanthakumar Thiagarajan1-0/+11
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Split off ANI control to the PHY opsFelix Fietkau1-0/+6
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Add abstraction for rx enableVasanthakumar Thiagarajan1-0/+5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Move some RF ops to the private callbacksLuis R. Rodriguez1-0/+113
The PHY split is easier done in a few steps. First move the RF ops to the private ops and rename them accordingly. We split PHY stuff up first for the AR5008 and AR9002 families. There are some callbacks that AR9002 share with the AR5008 familiy so we set those first, if AR9002 has some different callbacks it will override them upon hardware init. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: start building an abstraction layer for hardware routinesLuis R. Rodriguez1-0/+31
ath9k supports the AR5008, AR9001 and AR9002 family of Atheros chipsets, all 802.11n. The new breed of 802.11n chips, the AR9003 family will be supported as well soon. To help with its support we're going to add a few callbacks for hardware routines which differ considerably instead of adding branch checks for the revision at runtime. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-03-05 10:27:41 +0300