| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 3d60041543189438cd1b03a1fa40ff6681c77970 ]
Currently the resource allocated by crypto_alloc_shash() is not
freed in case ath12k_peer_find() fails, resulting in memory leak.
Add crypto_free_shash() to fix it.
This is found during code review, compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240526124226.24661-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a993772e0f0934d730c0d451622c80e03a40ab1 ]
Commit 5082b3e3027e ("wifi: ath11k: fix race due to setting
ATH11K_FLAG_EXT_IRQ_ENABLED too early") fixes a race in ath11k
driver. Since ath12k shares the same logic as ath11k, currently
the race also exists in ath12k: in ath12k_pci_ext_irq_enable(),
ATH12K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
In cases where only one MSI vector is allocated, this results
in a race condition: after ATH12K_FLAG_EXT_IRQ_ENABLED is set
but before NAPI enabled, CE interrupt breaks in. Since IRQ is
shared by CE and data path, ath12k_pci_ext_interrupt_handler()
is also called where we call disable_irq_nosync() to disable
IRQ. Then napi_schedule() is called but it does nothing because
NAPI is not enabled at that time, meaning that
ath12k_pci_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Since IRQ
is shared, all interrupts are disabled and we would finally
get no response from target.
So port ath11k fix here, this is done by setting
ATH12K_FLAG_EXT_IRQ_ENABLED after all NAPI and IRQ work are
done. With the fix, we are sure that by the time
ATH12K_FLAG_EXT_IRQ_ENABLED is set, NAPI is enabled.
Note that the fix above also introduce some side effects:
if ath12k_pci_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH12K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
This is found during code review.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240524023642.37030-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a47f3320bb4ba6714abe8dddb36399367b491358 upstream.
The ext interrupts are enabled when the firmware has been started, but
this may never happen, for example, if the board configuration file is
missing.
When the system is later suspended, the driver unconditionally tries to
disable interrupts, which results in an irq disable imbalance and causes
the driver to spin indefinitely in napi_synchronize().
Make sure that the interrupts have been enabled before attempting to
disable them.
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240709073132.9168-1-johan+linaro@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 253ec89c9013b0e61f5c54344df7c065d54934d1 ]
The Current method for advertising the maximum MBSSID interface count
assumes single radio per wiphy (multi wiphy model). However, this
assumption is incorrect for multi radio per wiphy (single wiphy model).
Therefore, populate the parameter for each radio present in the MAC
abstraction layer (ah). This approach ensure scalability for both single
wiphy and multi wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 519a545cfee7 ("wifi: ath12k: advertise driver capabilities for MBSSID and EMA")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240613153813.3509837-1-quic_periyasa@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1eeafd64c7b455381b77c546e41bc267e13e2809 ]
Currently, the Rx data path only supports parsing peer metadata of version
zero. However, the QCN9274 platform configures the peer metadata version
as V1B. When V1B peer metadata is parsed using the version zero logic,
invalid data is populated, causing valid packets to be dropped. To address
this issue, refactor the peer metadata version and add the version based
parsing to populate the data from peer metadata correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 287033810990 ("wifi: ath12k: add support for peer meta data version")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240624145418.2043461-1-quic_periyasa@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 519a545cfee790024c623c7aacd165f7431773d5 ]
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Set WMI_RSRC_CFG_FLAGS2_CALC_NEXT_DTIM_COUNT_SET flag to allow
firmware to track and update the DTIM counts for each nontransmitted
profile.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-2-quic_alokad@quicinc.com
Stable-dep-of: 1eeafd64c7b4 ("wifi: ath12k: fix peer metadata parsing")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8dd65ccbdf91e2fe3ab6e4da158b38f81746c3b4 ]
Function ath12k_debugfs_register() is called once inside the function
ath12k_mac_hw_register(). However, with single wiphy model, there could
be multiple pdevs registered under single hardware. Hence, need to register
debugfs for each one of them.
Move the caller inside the loop which iterates over all underlying pdevs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: f8bde02a26b9 ("wifi: ath12k: initial debugfs support")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-2-quic_adisi@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b2a12749b08726f006303814ecc1c37024d3617 ]
Currently ACPI notification handler is installed when driver loads and only
gets removed when driver unloads. During resume after firmware is reloaded,
ath12k tries to install it by default. Since it is installed already, ACPI
subsystem rejects it and returns an error:
[ 83.094206] ath12k_pci 0000:03:00.0: failed to install DSM notify callback: 7
Fix it by removing that handler when going to suspend. This also avoid any
possible ACPI call to firmware before firmware is reloaded/reinitialized.
Note ab->acpi also needs to be cleared in ath12k_acpi_stop() such that we
are in a clean state when ACPI structures are reinitialized in
ath12k_acpi_start().
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 576771c9fa21 ("wifi: ath12k: ACPI TAS support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531024000.9291-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ae570703754858a77cc42b3c9fff42e9f084608 ]
Base address of CE ring is defined as u32, currently this works
because DMA mask configured as 32 bit:
#define ATH12K_PCI_DMA_MASK 32
However this mask could be changed once firmware bugs are fixed
to fully support 36 bit DMA addressing. So to protect against any
future changes to the DMA mask, change the type of the fields that
are dependent upon it.
This is found during code review. Compile tested only.
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240524024021.37711-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a57ab7cced454f69b8ee8aa5f5019ea8de4674da ]
When handling fragmented packets, the ath12k driver reassembles each
fragment into a normal packet and then reinjects it into the HW ring.
However, a firmware crash occurs during this reinjection process.
The issue arises because the driver populates peer metadata in
reo_ent_ring->queue_addr_lo, while the firmware expects the physical
address obtained from the corresponding peer’s queue descriptor. Fix it
by filling peer's queue descriptor's physical address in queue_addr_lo.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520070045.631029-4-quic_ppranees@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 073f9f249eecd64ab9d59c91c4a23cfdcc02afe4 ]
The monitor ring and the reo reinject ring share the same ring mask index.
When the driver receives an interrupt for the reo reinject ring, the
monitor ring is also processed, leading to invalid memory access. Since
monitor support is not yet enabled in ath12k, the ring mask for the monitor
ring should be removed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520070045.631029-3-quic_ppranees@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33322e3ef07409278a18c6919c448e369d66a18e ]
For fragmented packets, ath12k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE. Otherwise,
an invalid payload may be reinjected into the HW and
subsequently delivered to the host.
Given that arbitrary memory can be allocated to the skb buffer,
knowledge about the data contained in the reinjected buffer is lacking.
Consequently, there’s a risk of private information being leaked.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520070045.631029-2-quic_ppranees@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33370412eced2dc7f81f4324e109d69319cafd82 ]
Smatch is throwing below warning:
Commit 692921ead832 ("wifi: ath12k: flush all packets before
suspend") leads to the following Smatch static checker warning:
drivers/net/wireless/ath/ath12k/core.c:58 ath12k_core_suspend()
warn: sleeping in atomic context
and also gives the reason:
drivers/net/wireless/ath/ath12k/core.c
48 int ret, i;
49
50 if (!ab->hw_params->supports_suspend)
51 return -EOPNOTSUPP;
52
53 rcu_read_lock();
^^^^^^^^^^^^^^^
Disables preemption.
54 for (i = 0; i < ab->num_radios; i++) {
55 ar = ath12k_mac_get_ar_by_pdev_id(ab, i);
56 if (!ar)
57 continue;
--> 58 ret = ath12k_mac_wait_tx_complete(ar);
^^^^^^^
Sleeping in atomic context.
59 if (ret) {
60 ath12k_warn(ab, "failed to wait tx complete: %d\n", ret);
61 rcu_read_unlock();
62 return ret;
63 }
64 }
65 rcu_read_unlock();
But it is weird that no warning on this in run time even with
CONFIG_DEBUG_ATOMIC_SLEEP=y. With some debug it is found that this is
because: when system goes to suspend, ath12k_mac_op_stop() gets called
where then in ath12k_mac_stop() ab->pdevs_active[ar->pdev_idx] is cleared.
This results in ath12k_mac_get_ar_by_pdev_id() always returning a NULL ar,
and thereby ath12k_mac_wait_tx_complete() never gets a chance to run.
Fix it by retrieving ar directly from ab->pdevs[].ar instead of using
ath12k_mac_get_ar_by_pdev_id(). Since ab->pdevs[].ar is set at boot time
and won't get cleared when suspend, ath12k_mac_wait_tx_complete() won't
be skipped. In addition, with ath12k_mac_get_ar_by_pdev_id() removed,
rcu_read_lock()/unlock() are not needed any more, so remove them. This
also fixes the warning above.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Fixes: 692921ead832 ("wifi: ath12k: flush all packets before suspend")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/7a96ca11-80b5-4751-8cfc-fa637f3aa63a@moroto.mountain/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240511095045.9623-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ce9ab2785e4e9ca0752390d8e5ab65bd08f0e78 ]
We observe intermittent ping failures from the access point (AP) to
station (STA) in any mode (AP-STA or Mesh) configured. Specifically,
the transmission completion status is not received at tx completion
ring id 4 (WBM2SW ring4) for the packets transmitted via TCL DATA
ring id 3. This prevents freeing up tx descriptors and leads
to buffer exhaustion.
Currently, during initialization of the WBM2SW ring, we are directly
mapping the ring number to the ring mask to obtain the ring mask
group index. This approach is causing setup failures for WBM2SW
ring 4. Similarly, during runtime, when receiving incoming
transmission completion status, the validation of the ring number by
mapping the interrupted ring mask. This is resulting in
validation failure. Thereby preventing entry into the completion
handler ath12k_dp_tx_completion_handler().
The existing design assumed that the ring numbers would always be
sequential and could be directly mapped with the ring mask. However,
this assumption does not hold true for WBM2SW ring 4. Therefore,
modify the design such that, instead of mapping the ring number,
the ring ID is mapped with the ring mask.
According to this design:
1. During initialization of the WBM2SW ring, mapping the ring ID
to the ring mask will ensure obtaining the correct ring mask group
ID.
2. During runtime, validating the interrupted ring mask group ID
within the transmission completion group is sufficient. This
approach allows the ring ID to be derived from the interrupted ring
mask and enables entry into the completion handler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240510070427.206152-1-quic_nithp@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3c84a74bd797f76d7da036c9fef947d674bbc18 ]
The frequency in the rx status is currently being filled
incorrectly for the 6 GHz band. The channel number received is
invalid in this case, resulting in packet drops. Fix this
issue by correcting the frequency calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-3-quic_pradeepc@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b0989e925f38df733a03ff5a320d6841006b3f9 ]
ath12k_mac_op_unassign_vif_chanctx() will do vdev stop in
ath12k_mac_monitor_stop(). This ath12k_mac_vdev_stop() will do vdev stop
again, then might trigger firmware crash.
So add judgement to avoid duplicated vdev stop.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: c9e4e41e71ff ("wifi: ath12k: move peer delete after vdev stop of station for WCN7850")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240429081525.983-3-quic_kangyang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50971dc6694c0845fcddfe337ea39c5b723d5a92 ]
In mesh node traffic, internal firmware-transmitted failures are
reported as transmitted failures in mesh metric calculation, leading
to the breakage of the mesh link.
Fix the issue by dropping the internal firmware-transmitted failures
before updating the TX completion status to mac80211, in order to
prevent false failure averaging in mesh metric calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430074313.885807-3-quic_kathirve@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5453bbd6fef4ca2fea3b4b338fc715d7135afc6f ]
When a station idles for a long time, hostapd will try to send
a QoS Null frame to the station as "poll". NL80211_CMD_PROBE_CLIENT
is used for this purpose.
And the skb will be added to ack_status_frame - waiting for a
completion via ieee80211_report_ack_skb().
But when the peer was already removed before the tx_complete arrives,
the peer will be missing. And when using dev_kfree_skb_any (instead
of going through mac80211), the entry will stay inside
ack_status_frames thus not clean up related information in its
internal data structures. This IDR will therefore run full after
8K request were generated for such clients.
At this point, the access point will then just stall and not allow
any new clients because idr_alloc() for ack_status_frame will fail.
ieee80211_free_txskb() on the other hand will (when required) call
ieee80211_report_ack_skb() and make sure that (when required) remove
the entry from the ack_status_frame and clean up related
information in its internal data structures.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-1-c0af729d6229@narfation.org
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430074313.885807-2-quic_kathirve@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
Currently, when using WCN7850 or QCN9274 as AP, ath12k always performs down
grade phy mode operation regardless of whether the firmware supports EHT
capability or not and then vdev will start in HE mode. When stations that
support EHT capability try to connect to the AP, the AP will set phy mode
to EHT after receiving the association request packet, and then send
WMI_PEER_ASSOC_CMDID command to firmware, AP’s firmware will crash.
This is because when the ath12k_mac_copy_sband_iftype_data() function
handles EHT capability, it does not copy the EHT capability into the
iftype[band][type] array according to the interface type. So, interface
type should not be used as an index to get eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
To address this issue, use types_mask to select the eht_cap in
ath12k_mac_check_down_grade_phy_mode() function.
This patch affects QCN9274 and WCN7850 because they have the same issue.
Hostapd log:
wlo1: STA 02:03:7f:37:12:34 IEEE 802.11: Could not set STA to kernel driver
Kernel log:
[270894.816076] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_SET_PARAM cmd
[270894.816111] ath12k_pci 0000:03:00.0: failed to setup peer SMPS for vdev 0: -108
[270894.816122] ath12k_pci 0000:03:00.0: Failed to associate station: 02:03:7f:37:12:34
[270894.843389] ieee80211 phy5: Hardware restart was requested
[270894.843517] ath12k_pci 0000:03:00.0: failed to lookup peer 02:03:7f:37:12:34 on vdev 0
[270894.843616] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_DELETE cmd
[270894.843650] ath12k_pci 0000:03:00.0: failed to delete peer vdev_id 0 addr 02:03:7f:37:12:34 ret -108
[270894.843663] ath12k_pci 0000:03:00.0: Failed to delete peer: 02:03:7f:37:12:34 for VDEV: 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425083837.5340-1-quic_lingbok@quicinc.com
|
|
Commit eaf9f17b861b ("wifi: ath12k: relocate ath12k_dp_pdev_pre_alloc()
call") moves ath12k_dp_pdev_pre_alloc() from ath12k_core_start() to
ath12k_mac_allocate(), resulting in ath12k_mac_flush() failure in
recovery scenarios:
[ 6849.684104] ath12k_pci 0000:04:00.0: pdev 0 successfully recovered
[ 6854.907320] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0
[ 6860.027353] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0
[ 6865.143385] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0
This is because, with ath12k_dp_pdev_pre_alloc() moved to ath12k_mac_allocate(),
dp->num_tx_pending is not reset due to ATH12K_FLAG_REGISTERED set in
recovery scenarios.
So a possible fix would be to reset that counter at some proper point,
just like the old design. But considering that the counter tracks number
of packets pending to be freed or returned to mac80211, forcefully reset
it might make it hard to expose some real issues. For example if somehow
ath12k fails to free/return some TX packets, we don't know that because
no warnings any more.
That is to say we should not reset that counter during recovery (which is
already done due to above commit), instead should decrease it each time
a packet is freed/returned. Currently almost each related function has
this logic implemented, except ath12k_dp_cc_cleanup(). So add the same
there to fix this issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240426015434.94840-1-quic_bqiang@quicinc.com
|
|
Currently in recovery/resume cases, we do not free M3 buffer but
instead will reuse it. This is done by checking m3_mem->vaddr: if it
is not NULL we believe M3 buffer is ready and go ahead to reuse it.
Note that m3_mem->size is not checked. This is safe for now because
currently M3 reuse logic only gets executed in recovery/resume cases
and the size keeps unchanged in either of them.
However ideally the size should be checked as well, to make the code
safer. So add the check there. Now if that check fails, free old M3
buffer and reallocate a new one.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: 303c017821d8 ("wifi: ath12k: fix kernel crash during resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425021740.29221-1-quic_bqiang@quicinc.com
|
|
Currently, mlo_capable_flags is set to zero if dualmac device is
detected based on One Time Programmable (OTP) register value.
This is not generic and in future dualmac devices may support
Single Link Operation (SLO) and Multi Link Operation (MLO).
Thus, set mlo_capable_flags based on 'single_chip_mlo_support'
parameter from QMI PHY capability response message from the firmware.
Also, add check on mlo_capable_flags to disable MLO parameter in the
host capability QMI request message.
If the firmware does not respond with this optional parameter
'single_chip_mlo_support' in QMI PHY capability response, default
ab->mlo_capable_flags is used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240418125609.3867730-3-quic_rajkbhag@quicinc.com
|
|
New parameter 'single_chip_mlo_support' was added in QMI PHY
capability response message. This is an optional parameter added
in QCN9274 firmware. This parameter states if the firmware
supports Single-Link Operation (SLO) and Multi-Link Operation (MLO)
within the same device.
If single_chip_mlo_support = 1, then intra device SLO/MLO is supported
in the firmware.
If single_chip_mlo_support = 0, then intra device SLO/MLO is not
supported in the firmware.
Hence, add support to read 'single_chip_mlo_support' parameter from
the QMI PHY capability response message.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240418125609.3867730-2-quic_rajkbhag@quicinc.com
|
|
When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
|
|
Currently, ath12k does not have the ability to set band edge channel power
for WCN7850. In order to support this, ath12k gets band edge channel power
table in ath12k_acpi_dsm_get_data() function and sets pdev_id and
param_type_id, then finally sends these data and
WMI_PDEV_SET_BIOS_INTERFACE_CMDID to firmware to set band edge channel
power.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-5-quic_lingbok@quicinc.com
|
|
Currently, ath12k does not have the ability to adjust Clear Channel Assessment
(CCA) threshold values to meet the regulatory requirements. Get the values from
ACPI and send them to the firmware using ath12k_wmi_set_bios_cmd() function.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-4-quic_lingbok@quicinc.com
|
|
In order to enable ACPI SAR (Specific Absorption Rate), ath12k gets SAR and GEO
offset tables from ACPI and sends the data to firmware using
WMI_PDEV_SET_BIOS_SAR_TABLE_CMDID and WMI_PDEV_SET_BIOS_GEO_TABLE_CMDID
commands.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-3-quic_lingbok@quicinc.com
|
|
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
|
|
Now that all things are ready, enable supports_suspend to
make suspend/resume work for WCN7850. Don't touch other
chips because they don't support suspend.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-11-quic_bqiang@quicinc.com
|
|
Now that all infrastructure is in place and ath12k is fixed to handle all the
corner cases, power down the ath12k firmware during suspend and power it back
up during resume.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath12k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath12k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath12k's suspend callback before calling all suspend_late callbacks, making
the first condition satisfied. And because MHI devices are children of ath12k
device (ab->dev), kernel guarantees that ath12k's suspend_late callback is
called after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath12k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which would succeed
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the potential probe-defer issue when
resume.
Also change related code due to interface changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-10-quic_bqiang@quicinc.com
|
|
Currently when resume ath12k_core_restart() calls
ath12k_core_pre_reconfigure_recovery() where mac80211 queues are
stopped by calling ieee80211_stop_queues(). Then in
ath12k_mac_op_reconfig_complete() those queues are not started
because ieee80211_wake_queues() is skipped due to the check on
reconfig_type. The result is that mac80211
could not deliver any frame to ath12k to send out, finally making
connection fail.
[84473.104249] PM: suspend exit
[84479.372397] wlan0: no VHT 160 MHz capability on 5 GHz, limiting to 80 MHz
[84479.372401] wlan0: determined local STA to be EHT, BW limited to 80 MHz
[84479.372416] wlan0: determined AP 00:03:7f:12:b7:b7 to be HE
[84479.372420] wlan0: connecting with HE mode, max bandwidth 80 MHz
[84479.580348] wlan0: authenticate with 00:03:7f:12:b7:b7 (local address=00:03:7f:37:11:53)
[84479.580351] wlan0: send auth to 00:03:7f:12:b7:b7 (try 1/3)
[84480.698993] wlan0: send auth to 00:03:7f:12:b7:b7 (try 2/3)
[84481.816505] wlan0: send auth to 00:03:7f:12:b7:b7 (try 3/3)
[84482.810966] wlan0: authentication with 00:03:7f:12:b7:b7 timed out
Actually we don't need to stop/start queues during suspend/resume,
so remove ath12k_core_pre_reconfigure_recovery() from ath12k_core_restart().
This won't cause any regression because currently the only chance
ath12k_core_restart() gets called is in reset case, where ab->is_reset
is set so that function will never be executed.
Also remove ath12k_core_post_reconfigure_recovery() because it is
not needed in suspend/resume case. This is also valid due to above
analysis.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-9-quic_bqiang@quicinc.com
|
|
Currently pktlog is stopped in suspend callback and started in
resume callback, and in either scenarios it's basically to
delete/modify ab->mon_reap_timer and to purge related rings.
For WCN7850 it's pointless because pktlog is not enabled: both
ab->mon_reap_timer and those rings are not initialized.
So remove pktlog handling in suspend/resume callbacks. And
further, remove these two functions and related callee because
no one is calling them.
Other chips are not affected because now only WCN7850 supports
suspend/resume.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-8-quic_bqiang@quicinc.com
|
|
In order to send out all packets before going to suspend, current code
adds a 500ms delay as a workaround. It is a rough estimate and may not
work.
Fix this by checking packet counters, if counters become zero, then all
packets are sent out or dropped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
|
|
Currently buf_len field of ath12k_mhi_config_wcn7850 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
For now we haven't get any failure report on this in ath12k, but
there indeed is one such case in ath11k [1].
Actually those buffers are used only by QMI target -> host communication.
And for WCN7850, the largest packet size for that is less than 6KB. So
change buf_len field to 8KB, which results in order 1 allocation if page
size is 4KB. In this way, we can at least save some memory, and as well
as decrease the possibility of allocation failure in those scenarios.
[1] https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-6-quic_bqiang@quicinc.com
|
|
We are seeing below warning in both reset and suspend/resume scenarios:
[ 4153.776040] ath12k_pci 0000:04:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath12k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-5-quic_bqiang@quicinc.com
|
|
Both the firmware reset feature and the power management
suspend/resume feature share common power-down and power-up
functionality. One aspect of the power-up functionality is
the handling of the ATH12K_QMI_EVENT_FW_INIT_DONE event.
When this event is received, a call is made to
ath12k_hal_dump_srng_stats(), with the purpose to collect
information that may be useful in debugging the cause of a
firmware reset.
Unfortunately, since this functionality is shared between
both the firmware reset path and the power management
resume path, the kernel log is flooded with messages during
resume. Since these messages are not useful during resume,
and in fact can be confusing and can increase the time it
takes to resume, update the logic to only call
ath12k_hal_dump_srng_stats() during firmware reset.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-4-quic_bqiang@quicinc.com
|
|
There is no driver to match these two channels, so
remove them. This fixes warnings from MHI subsystem during suspend:
mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting
mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-3-quic_bqiang@quicinc.com
|
|
For non-WoW suspend/resume, ath12k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath12k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-2-quic_bqiang@quicinc.com
|
|
Currently during resume, QMI target memory is not properly handled, resulting
in kernel crash in case DMA remap is not supported:
BUG: Bad page state in process kworker/u16:54 pfn:36e80
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80
page dumped because: nonzero _refcount
Call Trace:
bad_page
free_page_is_bad_report
__free_pages_ok
__free_pages
dma_direct_free
dma_free_attrs
ath12k_qmi_free_target_mem_chunk
ath12k_qmi_msg_mem_request_cb
The reason is:
Once ath12k module is loaded, firmware sends memory request to host. In case
DMA remap not supported, ath12k refuses the first request due to failure in
allocating with large segment size:
ath12k_pci 0000:04:00.0: qmi firmware request memory request
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144
ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size
ath12k_pci 0000:04:00.0: qmi delays mem_request 2
ath12k_pci 0000:04:00.0: qmi firmware request memory request
Later firmware comes back with more but small segments and allocation
succeeds:
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
Now ath12k is working. If suspend is triggered, firmware will be reloaded
during resume. As same as before, firmware requests two large segments at
first. In ath12k_qmi_msg_mem_request_cb() segment count and size are
assigned:
ab->qmi.mem_seg_count == 2
ab->qmi.target_mem[0].size == 7077888
ab->qmi.target_mem[1].size == 8454144
Then allocation failed like before and ath12k_qmi_free_target_mem_chunk()
is called to free all allocated segments. Note the first segment is skipped
because its v.addr is cleared due to allocation failure:
chunk->v.addr = dma_alloc_coherent()
Also note that this leaks that segment because it has not been freed.
While freeing the second segment, a size of 8454144 is passed to
dma_free_coherent(). However remember that this segment is allocated at
the first time firmware is loaded, before suspend. So its real size is
524288, much smaller than 8454144. As a result kernel found we are freeing
some memory which is in use and thus crashed.
So one possible fix would be to free those segments during suspend. This
works because with them freed, ath12k_qmi_free_target_mem_chunk() does
nothing: all segment addresses are NULL so dma_free_coherent() is not called.
But note that ath11k has similar logic but never hits this issue. Reviewing
code there shows the luck comes from QMI memory reuse logic. So the decision
is to port it to ath12k. Like in ath11k, the crash is avoided by adding
prev_size to target_mem_chunk structure and caching real segment size in it,
then prev_size instead of current size is passed to dma_free_coherent(),
no unexpected memory is freed now.
Also reuse m3 buffer.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240419034034.2842-1-quic_bqiang@quicinc.com
|
|
Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence
facing below KASAN warning,
==================================================================
BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148
Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273
CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0
Workqueue: qmi_msg_handler qmi_data_ready_work
Call trace:
dump_backtrace+0x0/0x20c
show_stack+0x14/0x1c
dump_stack+0xe0/0x138
print_address_description.isra.5+0x30/0x330
__kasan_report+0x16c/0x1bc
kasan_report+0xc/0x14
__asan_load8+0xa8/0xb0
qmi_invoke_handler+0xa4/0x148
qmi_handle_message+0x18c/0x1bc
qmi_data_ready_work+0x4ec/0x528
process_one_work+0x2c0/0x440
worker_thread+0x324/0x4b8
kthread+0x210/0x228
ret_from_fork+0x10/0x18
The address belongs to the variable:
ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k]
[...]
==================================================================
Add a dummy terminator entry at the end to assist the qmi_invoke_handler()
in traversing up to the terminator entry without accessing an
out-of-boundary index.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416080234.2882725-1-quic_kathirve@quicinc.com
|
|
Move the data path Tx and Rx descriptor primary page table CMEM
configuration into a helper function. This will make the code more
scalable for configuring partner device in support of multi-device MLO.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-5-quic_periyasa@quicinc.com
|
|
In the hardware cookie conversion table configuration, place the Rx
descriptor at the end. This will allow for easier addition of partner
device Rx descriptors in the future to support multi-device MLO.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-4-quic_periyasa@quicinc.com
|
|
Currently, the Rx descriptor is placed before the Tx descriptor in the
primary page table of the hardware cookie conversion configuration. The
Tx and Rx descriptor offsets are implicitly hardcoded. To allow for easy
displacement of Tx and Rx descriptors, introduce Tx and Rx offset based
cookie conversion initializationi. Additionally, should consider
validating the respective offset ranges while retrieving the Tx and Rx
descriptors. This change will be utilize by the next patch in the series.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-3-quic_periyasa@quicinc.com
|
|
Currently, in the Rx data path cookie conversion initialization procedure,
the primary page table index (ppt_idx) is computed within the secondary
page table iteration. However this is invariant, and hence the ppt_idx
should be calculated outside of the iteration to avoid repeated execution
of the statement.
Found in code review.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240411102226.4045323-2-quic_periyasa@quicinc.com
|
|
Currently, when debug logs are enabled, messages such as the following
are found in the kernel log:
event mgmt rx skb pK-error len 209 ftype 00 stype 50
The "pK-error" comes from using %pK to display an skb address in an
interrupt context.
Per the guidance in the current "printk-formats" documentation, %pK
"is only intended when producing content of a file read by userspace
from e.g. procfs or sysfs, not for dmesg."
So replace %pK with %p in all of the ath12k_dbg() format strings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
|
|
The survey dump statistics does not display channel RX and TX time
properly because the survey flag is not enabled in the firmware service
flag.
If firmware supports enable the service flag "bss_chan_info" in
wmi_resource_config to fetch and print the stats for specific pdev.
Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact
on WCN7850 since this bit is not utilized by the WCN7850 firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
|
|
ath12k will support Multi-Link Operation (MLO) in the future but not yet. A
major change with MLO is that cfg80211 will disable Wireless Extension (WEXT)
user space interface. To avoid having inconsistent user experience, first
supporting WEXT and later not, disable WEXT already now.
Now ath12k claims that WEXT is not supported:
$ iwconfig wlan0
wlan0 no wireless extensions.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240411165645.4071238-1-kvalo@kernel.org
|
|
Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
|
|
Currently, in the rx error data path, mac id is extracted from the
last 64bits of MSDU end description tag for each entry received in
the WBM error ring. Then, each entry will be updated into the MSDU
list for further processing. The extracted mac id is valid when a
single MSDU is not fragmented and received in the WBM error ring.
In scenarios where the size of a single MSDU received exceeds the
descriptor buffer size, resulting in fragmented or spillover MSDU
entries into the WBM error ring. In this case, the extracted mac id
from each spillover entry is invalid except the last spillover entry
of the MSDU. This invalid mac id leads to packet rejection.
To address this issue, check if the MSDU continuation flag is set,
then extract the valid mac id from the last spillover entry.
Propagate the valid mac id to all the spillover entries of the single
MSDU in the temporary MSDU list(scatter_msdu_list). Then, update this
into the MSDU list (msdu_list) for further processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240404141538.1277258-1-quic_nithp@quicinc.com
|
