summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath10k
AgeCommit message (Collapse)AuthorFilesLines
2019-05-07ath10k: Fix the tx stats bytes & packets parsingBrandon Huang1-3/+3
In tx_stats debugfs, txrate->flags may contain multiple bits. For example, RATE_INFO_FLAGS_SHORT_GI could be set, and tx stats bytes and packets will be not updated correctly. Fix this issue by using bit operation to check txrate->flags. Tested HW: QCA9984 Tested Firmware: 10.4-3.9.0.1-00007 Signed-off-by: Brandon Huang <yanghuan@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-07ath10k: Modify CE4 src buffer entries to 2048 for WCN3990Govind Singh1-1/+1
CE4 is host to target HTT tx pipe, tx completion are not served on time when CPU is loaded and this cause ce src ring full condition due to less no of src buffer entries. To mitigate the issue increase CE4 src buffer entries to 2048. Testing: Tested on QCS404 platform(WCN3990 HW) Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-07ath10k: Move board id and fw version logging to info levelGovind Singh1-7/+8
Board id and fw version is not printed by default in qmi cap response message. Move board id and fw version logging to info level for default logging. [ 34.005399] ath10k_snoc a000000.wifi: qmi chip_id 0x30b chip_family 0x4001 board_id 0xff soc_id 0x40070000 [ 34.005432] ath10k_snoc a000000.wifi: qmi fw_version 0x3106836b fw_build_timestamp 2019-02-13 10:24 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.1-00875-QCAHLSWMTPL-1 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-07ath10k: Added support to reset HTT stats in debugfsMaharaja Kennadyrajan4-4/+48
Reset HTT stats helps to get the aggregated HTT stats via tracing and also we can clear the accumulated HTT stats with this debugfs file. Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-07ath10k: Extended the HTT stats support to retrieve Mu-MIMO related statsMaharaja Kennadyrajan3-7/+8
Extended the bit mask value of the HTT stats to get the Mu-MIMO related stats via tracing. Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller7-11/+31
Three trivial overlapping conflicts. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-29ath10k: fix incorrect multicast/broadcast rate settingPradeep kumar Chitrapu1-3/+7
Invalid rate code is sent to firmware when multicast rate value of 0 is sent to driver indicating disabled case, causing broken mesh path. so fix that. Tested on QCA9984 with firmware 10.4-3.6.1-00827 Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053 (ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167). Fixes: cd93b83ad92 ("ath10k: support for multicast rate control") Co-developed-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Tested-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: enable QCA6174 hw3.2 SDIO hardwareWen Gong3-1/+29
After implementing PN replay check we can enable SDIO support on QCA6174. Tested with client mode on all security modes, and fragmentation as well. AP mode does not work yet. Also tone down the warning about SDIO being not ready yet. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode is not working yet. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: add fragmentation handler for high latency devicesWen Gong2-0/+243
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and all fragmented frames on receive path were lost in ath10k. Even a simple ping test failed with fragmentation. The fragmented packets are decapsulated based on the security mode, then the PN is checked and the fragmented frame is passed to mac80211. mac80211 in ieee80211_rx_h_defragment() will then combine the fragment frames and forward to upper layers. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: add PN replay protection for high latency devicesWen Gong1-2/+95
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data frame with an invalid PN number was not discard as it should have been. So this patch implements PN replay in ath10k. PN replay check for fragmented frames is implemented in followup patch. With low latency devices (PCI, AHB) hardware can store the data frames's content to host memory directly and the firmware can fully reorder data frames, and do PN replay check at the same time. But for high latency devices all data frames will be received and stored in firmware's memory and it is hard to do full reorder because of the memory size limitations in the firmware. This is why the PN replay protections needs to be implemented in host driver. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: add handler for HTT_T2H_MSG_TYPE_SEC_IND eventWen Gong1-0/+46
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores PN for replay check implemented in the following patch. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: add struct for high latency PN replay protectionWen Gong2-4/+47
Add the struct for PN replay protection and fragment packet handler. Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently used by SDIO firmware. The defines are not used yet so it's safe to modify them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as it's not either used in ath10k. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: Drop WARN_ON()s that always trigger during system resumeRafael J. Wysocki1-2/+2
ath10k_mac_vif_chan() always returns an error for the given vif during system-wide resume which reliably triggers two WARN_ON()s in ath10k_bss_info_changed() and they are not particularly useful in that code path, so drop them. Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1 Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1 Fixes: cd93b83ad927 ("ath10k: support for multicast rate control") Fixes: f279294e9ee2 ("ath10k: add support for configuring management packet rate") Cc: stable@vger.kernel.org Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Tested-by: Claire Chang <tientzu@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-29ath10k: perform crash dump collection in workqueueBrian Norris6-9/+29
Commit 25733c4e67df ("ath10k: pci: use mutex for diagnostic window CE polling") introduced a regression where we try to sleep (grab a mutex) in an atomic context: [ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254 [ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0 [ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4 [ 233.602642] Hardware name: Google Scarlet (DT) [ 233.602647] Call trace: [ 233.602663] dump_backtrace+0x0/0x11c [ 233.602672] show_stack+0x20/0x28 [ 233.602681] dump_stack+0x98/0xbc [ 233.602690] ___might_sleep+0x154/0x16c [ 233.602696] __might_sleep+0x78/0x88 [ 233.602704] mutex_lock+0x2c/0x5c [ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci] [ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci] [ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci] [ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci] [ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci] [ 233.602757] net_rx_action+0x140/0x388 [ 233.602766] __do_softirq+0x1b0/0x35c [...] ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware memory dumps are retrieved using the diag memory interface. A simple reproduction case is to run this on QCA6174A / WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the firmware: dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1 of=/dev/null (NB: simulated firmware crashes, via debugfs, don't trigger firmware dumps.) The fix is to move the crash-dump into a workqueue context, and avoid relying on 'data_lock' for most mutual exclusion. We only keep using it here for protecting 'fw_crash_counter', while the rest of the coredump buffers are protected by a new 'dump_mutex'. I've tested the above with simulated firmware crashes (debugfs 'reset' file), real firmware crashes (the 'dd' command above), and a variety of reboot and suspend/resume configurations on QCA6174A. Reported here: http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com Fixes: 25733c4e67df ("ath10k: pci: use mutex for diagnostic window CE polling") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-28netlink: make validation more configurable for future strictnessJohannes Berg1-2/+2
We currently have two levels of strict validation: 1) liberal (default) - undefined (type >= max) & NLA_UNSPEC attributes accepted - attribute length >= expected accepted - garbage at end of message accepted 2) strict (opt-in) - NLA_UNSPEC attributes accepted - attribute length >= expected accepted Split out parsing strictness into four different options: * TRAILING - check that there's no trailing data after parsing attributes (in message or nested) * MAXTYPE - reject attrs > max known type * UNSPEC - reject attributes with NLA_UNSPEC policy entries * STRICT_ATTRS - strictly validate attribute size The default for future things should be *everything*. The current *_strict() is a combination of TRAILING and MAXTYPE, and is renamed to _deprecated_strict(). The current regular parsing has none of this, and is renamed to *_parse_deprecated(). Additionally it allows us to selectively set one of the new flags even on old policies. Notably, the UNSPEC flag could be useful in this case, since it can be arranged (by filling in the policy) to not be an incompatible userspace ABI change, but would then going forward prevent forgetting attribute entries. Similar can apply to the POLICY flag. We end up with the following renames: * nla_parse -> nla_parse_deprecated * nla_parse_strict -> nla_parse_deprecated_strict * nlmsg_parse -> nlmsg_parse_deprecated * nlmsg_parse_strict -> nlmsg_parse_deprecated_strict * nla_parse_nested -> nla_parse_nested_deprecated * nla_validate_nested -> nla_validate_nested_deprecated Using spatch, of course: @@ expression TB, MAX, HEAD, LEN, POL, EXT; @@ -nla_parse(TB, MAX, HEAD, LEN, POL, EXT) +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression NLH, HDRLEN, TB, MAX, POL, EXT; @@ -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT) +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT) @@ expression TB, MAX, NLA, POL, EXT; @@ -nla_parse_nested(TB, MAX, NLA, POL, EXT) +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT) @@ expression START, MAX, POL, EXT; @@ -nla_validate_nested(START, MAX, POL, EXT) +nla_validate_nested_deprecated(START, MAX, POL, EXT) @@ expression NLH, HDRLEN, MAX, POL, EXT; @@ -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT) +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT) For this patch, don't actually add the strict, non-renamed versions yet so that it breaks compile if I get it wrong. Also, while at it, make nla_validate and nla_parse go down to a common __nla_validate_parse() function to avoid code duplication. Ultimately, this allows us to have very strict validation for every new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the next patch, while existing things will continue to work as is. In effect then, this adds fully strict validation for any new command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-23ath10k: sdio: add missing error checkErik Stromdahl1-0/+5
Although not likely, the bundle allocation might fail. Add proper error check and warning print. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: add initialization of HTC headerAlagu Sankar1-0/+1
HTC header carries junk values that may be interpreted by the firmware differently. Enable credit update only if flow control is enabled for the corresponding endpoint. Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: fix use-after-free on SDIO data framesKalle Valo1-0/+7
With SDIO there's a use after free after a data frame is transfered, call stack below. This happens because ath10k_htt_tx_hl() directly transmits the skb provided by mac80211 using ath10k_htc_send(), all other HTT functions use separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet. After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status() but HTT layer expects that it still owns the skb, and frees it in ath10k_htt_htc_tx_complete(). To fix this take a reference of skb before sending it to HTC layer to make sure we still own the skb. Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and SNOC) should be unaffected. call stack of use-after-free: dump_backtrace+0x0/0x2d8 show_stack+0x20/0x2c __dump_stack+0x20/0x28 dump_stack+0xc8/0xec print_address_description+0x74/0x240 kasan_report+0x258/0x274 __asan_report_load4_noabort+0x20/0x28 skb_pull+0xbc/0x114 ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core] ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio] process_one_work+0x3d8/0x8b0 worker_thread+0x518/0x7e0 kthread+0x260/0x278 ret_from_fork+0x10/0x18 Allocated by one task: kasan_kmalloc+0xa0/0x13c kasan_slab_alloc+0x14/0x1c kmem_cache_alloc+0x144/0x208 __alloc_skb+0xec/0x394 alloc_skb_with_frags+0x8c/0x374 sock_alloc_send_pskb+0x520/0x5d4 sock_alloc_send_skb+0x40/0x50 __ip_append_data+0xf5c/0x1858 ip_make_skb+0x194/0x1d4 udp_sendmsg+0xf24/0x1ab8 inet_sendmsg+0x1b0/0x2e0 sock_sendmsg+0x88/0xa0 __sys_sendto+0x220/0x3a8 __arm64_sys_sendto+0x78/0x80 el0_svc_common+0x120/0x1e0 el0_svc_compat_handler+0x64/0x80 el0_svc_compat+0x8/0x18 Freed by another task: __kasan_slab_free+0x120/0x1d4 kasan_slab_free+0x10/0x1c kmem_cache_free+0x74/0x504 kfree_skbmem+0x88/0xc8 __kfree_skb+0x24/0x2c consume_skb+0x114/0x18c __ieee80211_tx_status+0xb7c/0xf60 [mac80211] ieee80211_tx_status+0x224/0x270 [mac80211] ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core] ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core] ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core] ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio] process_sdio_pending_irqs+0xec/0x358 sdio_run_irqs+0x68/0xe4 sdio_irq_work+0x1c/0x28 process_one_work+0x3d8/0x8b0 worker_thread+0x518/0x7e0 kthread+0x260/0x278 ret_from_fork+0x10/0x18 Reported-by: Wen Gong <wgong@codeaurora.org> Tested-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: htt: support MSDU ids with SDIOAlagu Sankar3-1/+15
Transmit completion for SDIO is similar to PCIe, modify the high latency path to allow SDIO modules to use the msdu id. kvalo: the original patch from Alagu enabled this only for SDIO but I'm not sure should we also enable this with USB. I'll use bus params to enable this for so that it's easy to enable also for USB later. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org>. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: initialise struct ath10k_bus params to zeroKalle Valo5-5/+5
This way we don't need to set every variable and give them to default, which is zero. This is also safer in case we forgot to initalise a new field in some of the bus modules. Compile tested only. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: htt: don't use txdone_fifo with SDIOAlagu Sankar1-1/+3
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't even initialise it by skipping ath10k_htt_tx_alloc_buf() in ath10k_htt_tx_start(). Because of this using QCA6174 SDIO ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised txdone_fifo. So skip txdone_fifo when using High Latency mode. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: don't disable interrupts in ath10k_sdio_remove()Wen Gong1-2/+0
Disabling interrupts this early meant WMI communication was not working anymore when the SDIO device was removed. But we call ath10k_core_unregister() that will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So there's actually no need to disable interrupts here. Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop(). Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-23ath10k: sdio: workaround firmware UART pin configuration bugWen Gong2-1/+14
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is disabled from ath10k. SDIO firmware enables UART printouts by default. If ath10k will try to enable UART again the firmware will configure it's GPIO line incorrectly and SDIO interrupts won't work anymore. The workaround is to set UART pin again (19 for QCA6174 SDIO) if uart_print is 0. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-08mac80211: make ieee80211_schedule_txq schedule empty TXQsFelix Fietkau2-3/+3
Currently there is no way for the driver to signal to mac80211 that it should schedule a TXQ even if there are no packets on the mac80211 part of that queue. This is problematic if the driver has an internal retry queue to deal with software A-MPDU retry. This patch changes the behavior of ieee80211_schedule_txq to always schedule the queue, as its only user (ath9k) seems to expect such behavior already: it calls this function on tx status and on powersave wakeup whenever its internal retry queue is not empty. Also add an extra argument to ieee80211_return_txq to get the same behavior. This fixes an issue on ath9k where tx queues with packets to retry (and no new packets in mac80211) would not get serviced. Fixes: 89cea7493a346 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-02-28ath10k: Fill rx duration for each peer in fw_stats for WCN3990Surabhi Vishnoi6-6/+60
Currently, rx_duration for each peer is not getting populated in fw_stats debugfs entry for WCN3990. WCN3990 firmware sends rx duration for each peer as part of peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats, firmware expects host to send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD. Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer in fw_stats debugfs entry. Currently the driver handles 32-bit rx_duration, but the rx_duration for WCN3990 can be upto 63 bit. The firmware sends rx_duration split into two 32-bit fields, with the upper 32-bits being valid only if its MSB is set. This change handles the 63-bit rx_duration obtained from WCN3990 and maintain the backward compatibility. To get the rx_duration of each connected peer : cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-28ath10k: Fix the wrong calculation ht_idx and idx of rate table for tx_statsSurabhi Vishnoi1-3/+3
ht_idx (ht rate index) and idx (rate table index) are calculated based on mcs index. This mcs index used in the above calculation should be 0-9 for getting the correct ht_idx and idx. Currently the mcs index used for the above calculations is mcs index which can be 0-31 (in case of HT), leading to incorrect rate index and ht index values. Fix the issue by obtaining mcs value from the ratecode reported by firmware and use it for calculating ht_idx and idx (rate-table index). Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: e88975ca37d1 ("ath10k: dump tx stats in rate table format") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-28ath10k: Fix the wrong updation of SGI in tx_stats debugfsSurabhi Vishnoi2-1/+4
The SGI is updated wrongly in tx stats table in debugfs per sta entry. To know whether the packets/bytes are sent with SHORT GI, test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or not in the txrate flags. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-28ath10k: Fix the wrong updation of BW in tx_stats debugfs entrySurabhi Vishnoi2-4/+5
Currently, the bandwidth is updated wrongly in BW table in tx_stats debugfs per sta as there is difference in number of bandwidth type in mac80211 and driver stats table. This leads to bandwidth getting updated at wrong index in bandwidth table in tx_stats. Fix this index mismatch between mac80211 and driver stats table (BW table) by making the number of bandwidth type in driver compatible with mac80211. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-28ath10k: Fix the incorrect updation of NSS data in tx statsSurabhi Vishnoi1-8/+8
The NSS data is updated incorrectly in the tx stats as the array indexing starts from zero. Fix the incorrect updation of NSS data in tx_stats by taking into consideration the array index starting from zero. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support") Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: update the max num of peers supported for WCN3990Abhishek Ambure2-6/+6
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards supports maximum 33 peers including self peer. To support maximum peers, send updated peer param to firmware during initialization. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: remove the calibration data fetch for sdioWen Gong1-0/+3
The calibration data fetch will trigger sdio error, then sdio will become fail untill reboot system. If happens when run ifconfig wlan down, then ifconfig wlan up will fail untill reboot system.Remove it fix the ifconfig wlan issue. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: Fix length of wmi tlv command for protected mgmt framesSurabhi Vishnoi1-3/+1
The length of wmi tlv command for management tx send is calculated incorrectly in case of protected management frames as there is addition of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of firmware as the wmi tlv mgmt tx send command for protected mgmt frames is formed wrongly. Fix the length calculation of wmi tlv command for mgmt tx send in case of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only once. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi" Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: don't report unset rssi values to mac80211Alagu Sankar1-3/+9
The SDIO firmware does not provide RSSI value to the host, it's only set to zero. In that case don't report the value to mac80211. One risk here is that value zero might be a valid value with other firmware, currently there's no way to detect that. Without the fix, the rssi value indicated by iw changes between the actual value and -95. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1. Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: sdio: reset chip on power_down()Wen Gong1-8/+16
The target device needs to be reset during power_down(), otherwise only the first power_up() will work. And as ath10k calls power_up() during driver initialisation the driver would be otherwise unusable. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: sdio: disable fwlog printsAlagu Sankar1-0/+7
The SDIO firmware may turn it on based on scratch registers so disable the firmware log to avoid that. Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: sdio: set hi_acs_flagsAlagu Sankar1-3/+9
The SDIO firmware does not allow transmitting packets with the reduced tx completion HI_ACS option. SDIO firmware uses 1544 as alternate credit size, which is not big enough for the maximum sized mac80211 frames. Disable both these HI_ACS flags for SDIO. Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: correct the format of host memory chunks in wmi init commandYu Wang1-3/+36
This is a theoretical fix, the issue is found in code review. When adding the host memory chunks into wmi-tlv init command, there is no separate tlv header for each host memory chunk in the struct array, which breaches the convention between host and firmware, will result in mismatch between the two. To fix this issue, add separate tlv headers for the host memory chunks in wmi-tlv init command. Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: enhance logging for vdev pdev & peer set paramRakesh Pillai1-3/+7
Currently after enabling the WMI debug logging, there is no detail printed about the param id and the param value for the pdev, vdev and peer params which are set. Enhance the WMI logging to print the param id and the param value for pdev, vdev and peer set param wmi commands. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: add support for ack rssi value of data tx packetsAbhishek Ambure4-6/+146
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that the firmware has the capability to send the RSSI value of the ACK for all data and management packets transmitted. If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware sends RSSI value in "data" tx completion event. Host extracts ack rssi values of data packets from their tx completion event. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: add support for ack rssi value of management tx packetsAbhishek Ambure4-13/+90
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that the firmware has the capability to send the RSSI value of the ACK for all data and management packets transmitted. If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware sends RSSI value in "management" tx completion event. Host extracts ack rssi values of management packets from their tx completion event. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: fix descriptor size in ce tx completion for WCN3990Rakesh Pillai2-2/+66
When the driver receives the tx completion of the descriptor over ce, it clears the nbytes configured for that particular descriptor. WCN3990 uses ce descriptors with 64-bit address. Currently during handling the tx completion of the descriptors, the nbytes are accessed from the descriptors using ce_desc for 32-bit targets. This will lead to clearing of memory at incorrect offset if DMA MASK is set to greater than 32 bits. Attach different ce tx copy completed handler for targets using address above 32-bit address. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-20ath10k: switch to use SPDX license identifiersKalle Valo61-721/+61
Use SPDX identifiers everywhere in ath10k. Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license"), fix that as well. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-20ath10k: change 'unsigned long int' to 'unsigned long'Kalle Valo5-32/+32
Fixes checkpatch warnings: Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: copy the whole struct ath10k_bus_params in ath10k_core_register()Kalle Valo1-3/+2
Instead of copying fields one by one copy the whole structure. This way there's no need to modify the function every time we add a new field to the struct. Compile tested only. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: fix documentation in ath10k_wow_convert_8023_to_80211()Kalle Valo1-4/+3
With W=1 there's a warning: drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211' drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211' Fix it by changing the documentation marker '/**' to a normal code comment. While at it, clean up the line wrapping. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: align ath10k_htt_txbuf structuresKalle Valo1-2/+2
With W=1 GCC warns: drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned] drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned] Fix that by using __align(4). Compile tested only. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: change wmi.h to include only ieee80211.hKalle Valo1-1/+1
wmi.h does not use anything from mac80211.h so change it to include only ieee80211.h. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: make wmi_service_name() warn about missing service idsKalle Valo1-2/+6
When adding a new value to enum wmi_service it's very easy to miss that the new value should be also added to wmi_service_name() mapping function. Modify the function so that GCC can now warn about this: drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch] And also add a reminder to the enum. Thanks to Jouni Malinen for the idea. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: add missing values to wmi_service_name()Kalle Valo1-0/+6
After implementing the next patch GCC reported: drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch] drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch] drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch] drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch] drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch] drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-12ath10k: report tx airtime provided by fwManikanta Pubbisetty6-5/+86
If supported, update transmit airtime in mac80211 with the airtime values reported by the firmware. TX airtime of the PPDU is reported via HTT data TX completion indication message. A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise the firmware support. For firmwares which do not support this feature, TX airtime is calculated in the driver using TX bitrate. Hardwares tested : QCA9984 Firmwares tested : 10.4-3.6.1-00841 Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-23 20:56:55 +0300