| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
sdio bus bandwidth is low, sometimes for high performance TX test,
it will lack of ath10k_sdio_bus_request, it will print message:
ath10k_sdio mmc1:0001:1: unable to allocate bus request for async request
change the num from 64 to 1024 will not happen it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-3-wgong@codeaurora.org
|
|
For sdio chip, it is high latency bus, all the TX packet's content will
be tranferred from HOST memory to firmware memory via sdio bus, then it
need much more memory in firmware than low latency bus chip, for low
latency chip, such as PCI-E, it only need to transfer the TX descriptor
via PCI-E bus to firmware memory. For sdio chip, reduce the complexity of
TX logic will help TX efficiency since its memory is limited, and it will
reduce the TX circle's time of each packet and then firmware will have more
memory for TX since TX complete also need memeory.
This patch disable TX complete indication from firmware for htt data
packet, it will not have TX complete indication from firmware to ath10k.
It will cut the cost of bus bandwidth of TX complete and make the TX
logic of firmware simpler, it results in significant performance
improvement on TX path.
Udp TX throughout is 130Mbps without this patch, and it arrives
400Mbps with this patch.
The downside of this patch is the command "iw wlan0 station dump" will
show 0 for "tx retries" and "tx failed" since all tx packet's status
is success.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-2-wgong@codeaurora.org
|
|
Currently sta airtime is updated without any lock in case of
host based airtime calculation. Which may result in accessing the
invalid sta pointer in case of continuous station connect/disconnect.
This patch fix the kernel null pointer dereference by updating the
station airtime with proper RCU lock in case of host based airtime
calculation.
Proceeding with the analysis of "ARM Kernel Panic".
The APSS crash happened due to OOPS on CPU 0.
Crash Signature : Unable to handle kernel NULL pointer dereference
at virtual address 00000300
During the crash,
PC points to "ieee80211_sta_register_airtime+0x1c/0x448 [mac80211]"
LR points to "ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core]".
The Backtrace obtained is as follows:
[<bf880238>] (ieee80211_sta_register_airtime [mac80211]) from
[<bf945a38>] (ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core])
[<bf945a38>] (ath10k_txrx_tx_unref [ath10k_core]) from
[<bf9428e4>] (ath10k_htt_txrx_compl_task+0xa50/0xfc0 [ath10k_core])
[<bf9428e4>] (ath10k_htt_txrx_compl_task [ath10k_core]) from
[<bf9b9bc8>] (ath10k_pci_napi_poll+0x50/0xf8 [ath10k_pci])
[<bf9b9bc8>] (ath10k_pci_napi_poll [ath10k_pci]) from
[<c059e3b0>] (net_rx_action+0xac/0x160)
[<c059e3b0>] (net_rx_action) from [<c02329a4>] (__do_softirq+0x104/0x294)
[<c02329a4>] (__do_softirq) from [<c0232b64>] (run_ksoftirqd+0x30/0x90)
[<c0232b64>] (run_ksoftirqd) from [<c024e358>] (smpboot_thread_fn+0x25c/0x274)
[<c024e358>] (smpboot_thread_fn) from [<c02482fc>] (kthread+0xd8/0xec)
Tested HW: QCA9888
Tested FW: 10.4-3.10-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585736290-17661-1-git-send-email-vnaralas@codeaurora.org
|
|
Enable radar detection in secondary segment for VHT160 and VHT80+80 mode
on DFS channels. Otherwise, when injecting radar pulse in the secondary
segment, the DUT can't detect radar pulse.
Tested: qca9984 with firmware ver 10.4-3.10-00047
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-2-git-send-email-ssreeela@codeaurora.org
|
|
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.com
https://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-1-git-send-email-ssreeela@codeaurora.org
|
|
There is a race condition, when the user writes 'hw-restart' and
'hard' in the simulate_fw_crash debugfs file without any delay.
In the above scenario, the firmware dump work queue(scheduled by
'hard') should be handled gracefully, while the target is in the
'hw-restart'.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Co-developed-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213077-28439-1-git-send-email-mkenna@codeaurora.org
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
|
|
Hardwares tested : QCA9887
Firmwares tested : 10.4-3.9.0.1-00036
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When use command to read values, it crashed.
command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))
It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.
Then system crash:
[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281] ESR = 0x96000045
[ 1786.013291] Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299] SET = 0, FnV = 0
[ 1786.013307] EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322] ISV = 0, ISS = 0x00000045
[ 1786.013330] CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903] __memcpy+0x94/0x180
[ 1786.013914] unmap_single+0x6c/0x84
[ 1786.013925] swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938] __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952] msdc_unprepare_data+0x6c/0x84
[ 1786.013963] msdc_request_done+0x58/0x84
[ 1786.013974] msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985] msdc_irq+0x12c/0x17c
[ 1786.013996] __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006] handle_irq_event_percpu+0x28/0x68
[ 1786.014015] handle_irq_event+0x48/0x78
[ 1786.014026] handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039] __handle_domain_irq+0x84/0xc4
[ 1786.014050] gic_handle_irq+0x124/0x1a4
[ 1786.014059] el1_irq+0xb0/0x128
[ 1786.014072] cpuidle_enter_state+0x298/0x328
[ 1786.014082] cpuidle_enter+0x30/0x40
[ 1786.014094] do_idle+0x190/0x268
[ 1786.014104] cpu_startup_entry+0x24/0x28
[ 1786.014116] rest_init+0xd4/0xe0
[ 1786.014126] start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none
For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
|
|
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b1462f706a1950a355fd086e1c450b6
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix warnings which were recently introduced:
drivers/net/wireless/ath/ath10k/ahb.c:462: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/ahb.c:470: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/sdio.c:697: space prohibited before that close parenthesis ')'
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Ftrace is one of the last W^X violators (after this only KLP is
left). These patches move it over to the generic text_poke()
interface and thereby get rid of this oddity. This requires a
surprising amount of surgery, by Peter Zijlstra.
- x86/AMD PMUs: add support for 'Large Increment per Cycle Events' to
count certain types of events that have a special, quirky hw ABI
(by Kim Phillips)
- kprobes fixes by Masami Hiramatsu
Lots of tooling updates as well, the following subcommands were
updated: annotate/report/top, c2c, clang, record, report/top TUI,
sched timehist, tests; plus updates were done to the gtk ui, libperf,
headers and the parser"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
perf/x86/amd: Add support for Large Increment per Cycle Events
perf/x86/amd: Constrain Large Increment per Cycle events
perf/x86/intel/rapl: Add Comet Lake support
tracing: Initialize ret in syscall_enter_define_fields()
perf header: Use last modification time for timestamp
perf c2c: Fix return type for histogram sorting comparision functions
perf beauty sockaddr: Fix augmented syscall format warning
perf/ui/gtk: Fix gtk2 build
perf ui gtk: Add missing zalloc object
perf tools: Use %define api.pure full instead of %pure-parser
libperf: Setup initial evlist::all_cpus value
perf report: Fix no libunwind compiled warning break s390 issue
perf tools: Support --prefix/--prefix-strip
perf report: Clarify in help that --children is default
tools build: Fix test-clang.cpp with Clang 8+
perf clang: Fix build with Clang 9
kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic
tools lib: Fix builds when glibc contains strlcpy()
perf report/top: Make 'e' visible in the help and make it toggle showing callchains
perf report/top: Do not offer annotation for symbols without samples
...
|
|
Use device_get_match_data() here to simplify the code a bit.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some printks in here don't have newlines at the end, meaning the log
will be sort of hard to read. Add newlines.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb6 ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For some targets ex: QCS404, SCM permissions for MSA region is
statically configured in TrustZone fw. Add SCM call disable option
for such targets to avoid duplicate permissions.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reverts commit 76d164f582150fd0259ec0fcbc485470bcd8033e.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When simulate random transfer fail for sdio write and read, it crash
sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. it crash, the act len of ath10k_htc_hdr is higher than allocate len, it cause panic:
[ 99.723482] skbuff: skb_over_panic: text:00000000caa0f780 len:57013 put:57013 head:000000004116f24a data:0000000019ecb4dc tail:0xdef5 end:0x640 dev:<NULL>
[ 99.737697] ------------[ cut here ]------------
[ 99.742327] kernel BUG at /mnt/host/source/src/third_party/kernel/v4.19/net/core/skbuff.c:104!
[ 99.750937] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 99.831154] Process kworker/0:2 (pid: 151, stack limit = 0x00000000728010bf)
[ 99.838200] CPU: 0 PID: 151 Comm: kworker/0:2 Tainted: G W 4.19.85 #48
[ 99.846022] Hardware name: MediaTek krane sku0 board (DT)
[ 99.851429] Workqueue: events sdio_irq_work
[ 99.855614] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 99.860402] pc : skb_panic+0x64/0x68
[ 99.863974] lr : skb_panic+0x64/0x68
[ 99.867542] sp : ffffff8008833a90
[ 99.870850] x29: ffffff8008833ac0 x28: ffffffe52e337370
[ 99.876159] x27: ffffffe52e328a90 x26: 000000000000e0d0
[ 99.881469] x25: ffffffe52e336b60 x24: 000000000000deb5
[ 99.886779] x23: ffffffe52e340680 x22: ffffffe4efd47e00
[ 99.892088] x21: 000000000000deb5 x20: ffffffa516d85b4c
[ 99.897397] x19: ffffffa526928037 x18: 0000000000000000
[ 99.902706] x17: 000000000000003c x16: ffffffa5265b6c80
[ 99.908015] x15: 0000000000000006 x14: 3a76656420303436
[ 99.913325] x13: 0000000000029bf0 x12: 0000000000000000
[ 99.918634] x11: 0000000000000000 x10: 0000000000000000
[ 99.923943] x9 : a3b907e4b2783000 x8 : a3b907e4b2783000
[ 99.929253] x7 : 0000000000000000 x6 : ffffffa526f66d76
[ 99.934563] x5 : 0000000000000000 x4 : 0000000000000000
[ 99.939872] x3 : 000000000002a5ab x2 : ffffffe53feed918
[ 99.945182] x1 : ffffffe53fee4a08 x0 : 000000000000008e
[ 99.950491] Call trace:
[ 99.952937] skb_panic+0x64/0x68
[ 99.956165] skb_put+0x7c/0x84
[ 99.959224] ath10k_sdio_irq_handler+0x740/0xbb8 [ath10k_sdio]
[ 99.965055] process_sdio_pending_irqs+0x58/0x1a4
[ 99.969758] sdio_run_irqs+0x34/0x60
[ 99.973329] sdio_irq_work+0x1c/0x28
[ 99.974930] cros-ec-spi spi2.0: SPI transfer timed out
[ 99.976904] process_one_work+0x210/0x410
[ 99.976911] worker_thread+0x234/0x3dc
[ 99.976923] kthread+0x120/0x130
[ 99.982090] cros-ec-spi spi2.0: spi transfer failed: -110
[ 99.986054] ret_from_fork+0x10/0x18
[ 99.986063] Code: aa1403e2 2a1503e4 a90023e9 97e37d1a (d4210000)
[ 99.986068] ---[ end trace cb6d948c5a0fd6c7 ]---
[ 100.017250] Kernel panic - not syncing: Fatal exception
[ 100.018879] cros-ec-spi spi2.0: Command xfer error (err:-110)
[ 100.023659] SMP: stopping secondary CPUs
[ 100.023703] Kernel Offset: 0x251dc00000 from 0xffffff8008000000
[ 100.023707] CPU features: 0x0,2188200c
[ 100.023709] Memory Limit: none
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 8 bytes will be considered as ath10k_htc_hdr,
but actually the 8 bytes is not the ath10k_htc_hdr, so the act_len
from this ath10k_htc_hdr is not correct, if it is a big value, such
as 57013, it will trigger skb_panic.
Drop the skb with invalid length will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes coccicheck warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The description of ath10k_pci_dump_memory_sram() is inaccurate, an error
can never be returned, it is always the length. Update the comment to
reflect.
Fixes: 219cc084c6706 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6706 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Mere overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix some typo:
s/to to/to/
s/even/event/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5ad ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.
htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 224776520ead69e ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
sdio does not support wow, this patch is to enable it. When system enter
sleep state, if wowlan is enabled, then sdio chip will keep power if
platform support keep power, after resume, it will not need to re-load
firmware again.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Change log level from warn to dbg level of mpdu status
of sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.
This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.
htc.c:803: ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881: ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 dBm
signal avg: -82 dBm
after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 [-84, -88] dBm
signal avg: -82 [-84, -87] dBm
For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.
rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128
rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128
after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.
iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
signal: -70 [-77, -72] dBm
signal avg: -69 [-78, -72] dBm
iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
signal: -47 [-55, -48, -87, -88] dBm
signal avg: -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
signal: -43 [-46, -45, -79, -84] dBm
signal avg: -43 [-46, -46, -82, -83] dBm
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the BDF download QMI message has the end field set to 1, it signals
the end of the transfer, and triggers the firmware to do a CRC check. The
BDFs for msm8998 devices fail this check, yet the firmware is happy to
still use the BDF. It appears that this error is not caught by the
downstream drive by concidence, therefore there are production devices
in the field where this issue needs to be handled otherwise we cannot
support wifi on them. So, attempt to detect this scenario as best we can
and treat it as non-fatal.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
