| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit f020d9570a04df0762a2ac5c50cf1d8c511c9164 ]
When peer delete failed in a disconnect operation, use-after-free
detected by KFENCE in below log. It is because for each vdev_id and
address, it has only one struct ath10k_peer, it is allocated in
ath10k_peer_map_event(). When connected to an AP, it has more than
one HTT_T2H_MSG_TYPE_PEER_MAP reported from firmware, then the
array peer_map of struct ath10k will be set muti-elements to the
same ath10k_peer in ath10k_peer_map_event(). When peer delete failed
in ath10k_sta_state(), the ath10k_peer will be free for the 1st peer
id in array peer_map of struct ath10k, and then use-after-free happened
for the 2nd peer id because they map to the same ath10k_peer.
And clean up all peers in array peer_map for the ath10k_peer, then
user-after-free disappeared
peer map event log:
[ 306.911021] wlan0: authenticate with b0:2a:43:e6:75:0e
[ 306.957187] ath10k_pci 0000:01:00.0: mac vdev 0 peer create b0:2a:43:e6:75:0e (new sta) sta 1 / 32 peer 1 / 33
[ 306.957395] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 306.957404] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 306.986924] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 166
peer unmap event log:
[ 435.715691] wlan0: deauthenticating from b0:2a:43:e6:75:0e by local choice (Reason: 3=DEAUTH_LEAVING)
[ 435.716802] ath10k_pci 0000:01:00.0: mac vdev 0 peer delete b0:2a:43:e6:75:0e sta ffff990e0e9c2b50 (sta gone)
[ 435.717177] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 435.717186] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 435.717193] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 166
use-after-free log:
[21705.888627] wlan0: deauthenticating from d0:76:8f:82:be:75 by local choice (Reason: 3=DEAUTH_LEAVING)
[21713.799910] ath10k_pci 0000:01:00.0: failed to delete peer d0:76:8f:82:be:75 for vdev 0: -110
[21713.799925] ath10k_pci 0000:01:00.0: found sta peer d0:76:8f:82:be:75 (ptr 0000000000000000 id 102) entry on vdev 0 after it was supposedly removed
[21713.799968] ==================================================================
[21713.799991] BUG: KFENCE: use-after-free read in ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.799991]
[21713.799997] Use-after-free read at 0x00000000abe1c75e (in kfence-#69):
[21713.800010] ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.800041] drv_sta_state+0x115/0x677 [mac80211]
[21713.800059] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800076] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800093] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800110] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800137] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800153] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800161] genl_rcv_msg+0x38e/0x3be
[21713.800166] netlink_rcv_skb+0x89/0xf7
[21713.800171] genl_rcv+0x28/0x36
[21713.800176] netlink_unicast+0x179/0x24b
[21713.800181] netlink_sendmsg+0x3a0/0x40e
[21713.800187] sock_sendmsg+0x72/0x76
[21713.800192] ____sys_sendmsg+0x16d/0x1e3
[21713.800196] ___sys_sendmsg+0x95/0xd1
[21713.800200] __sys_sendmsg+0x85/0xbf
[21713.800205] do_syscall_64+0x43/0x55
[21713.800210] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[21713.800213]
[21713.800219] kfence-#69: 0x000000009149b0d5-0x000000004c0697fb, size=1064, cache=kmalloc-2k
[21713.800219]
[21713.800224] allocated by task 13 on cpu 0 at 21705.501373s:
[21713.800241] ath10k_peer_map_event+0x7e/0x154 [ath10k_core]
[21713.800254] ath10k_htt_t2h_msg_handler+0x586/0x1039 [ath10k_core]
[21713.800265] ath10k_htt_htc_t2h_msg_handler+0x12/0x28 [ath10k_core]
[21713.800277] ath10k_htc_rx_completion_handler+0x14c/0x1b5 [ath10k_core]
[21713.800283] ath10k_pci_process_rx_cb+0x195/0x1df [ath10k_pci]
[21713.800294] ath10k_ce_per_engine_service+0x55/0x74 [ath10k_core]
[21713.800305] ath10k_ce_per_engine_service_any+0x76/0x84 [ath10k_core]
[21713.800310] ath10k_pci_napi_poll+0x49/0x144 [ath10k_pci]
[21713.800316] net_rx_action+0xdc/0x361
[21713.800320] __do_softirq+0x163/0x29a
[21713.800325] asm_call_irq_on_stack+0x12/0x20
[21713.800331] do_softirq_own_stack+0x3c/0x48
[21713.800337] __irq_exit_rcu+0x9b/0x9d
[21713.800342] common_interrupt+0xc9/0x14d
[21713.800346] asm_common_interrupt+0x1e/0x40
[21713.800351] ksoftirqd_should_run+0x5/0x16
[21713.800357] smpboot_thread_fn+0x148/0x211
[21713.800362] kthread+0x150/0x15f
[21713.800367] ret_from_fork+0x22/0x30
[21713.800370]
[21713.800374] freed by task 708 on cpu 1 at 21713.799953s:
[21713.800498] ath10k_sta_state+0x2c6/0xb8a [ath10k_core]
[21713.800515] drv_sta_state+0x115/0x677 [mac80211]
[21713.800532] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800548] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800565] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800581] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800598] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800614] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800619] genl_rcv_msg+0x38e/0x3be
[21713.800623] netlink_rcv_skb+0x89/0xf7
[21713.800628] genl_rcv+0x28/0x36
[21713.800632] netlink_unicast+0x179/0x24b
[21713.800637] netlink_sendmsg+0x3a0/0x40e
[21713.800642] sock_sendmsg+0x72/0x76
[21713.800646] ____sys_sendmsg+0x16d/0x1e3
[21713.800651] ___sys_sendmsg+0x95/0xd1
[21713.800655] __sys_sendmsg+0x85/0xbf
[21713.800659] do_syscall_64+0x43/0x55
[21713.800663] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Fixes: d0eeafad1189 ("ath10k: Clean up peer when sta goes away.")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220801141930.16794-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b72a4aff947ba807177bdabb43debaf2c66bee05 ]
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Below is the crash stack for reference:
[ 428.469167] ------------[ cut here ]------------
[ 428.469180] kernel BUG at mm/slub.c:4150!
[ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 428.469219] Workqueue: events_unbound async_run_entry_fn
[ 428.469230] RIP: 0010:kfree+0x319/0x31b
[ 428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246
[ 428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000
[ 428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000
[ 428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000
[ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 428.469285] Call Trace:
[ 428.469295] ? dma_free_attrs+0x5f/0x7d
[ 428.469320] ath10k_core_stop+0x5b/0x6f
[ 428.469336] ath10k_halt+0x126/0x177
[ 428.469352] ath10k_stop+0x41/0x7e
[ 428.469387] drv_stop+0x88/0x10e
[ 428.469410] __ieee80211_suspend+0x297/0x411
[ 428.469441] rdev_suspend+0x6e/0xd0
[ 428.469462] wiphy_suspend+0xb1/0x105
[ 428.469483] ? name_show+0x2d/0x2d
[ 428.469490] dpm_run_callback+0x8c/0x126
[ 428.469511] ? name_show+0x2d/0x2d
[ 428.469517] __device_suspend+0x2e7/0x41b
[ 428.469523] async_suspend+0x1f/0x93
[ 428.469529] async_run_entry_fn+0x3d/0xd1
[ 428.469535] process_one_work+0x1b1/0x329
[ 428.469541] worker_thread+0x213/0x372
[ 428.469547] kthread+0x150/0x15f
[ 428.469552] ? pr_cont_work+0x58/0x58
[ 428.469558] ? kthread_blkcg+0x31/0x31
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220426221859.v2.1.I650b809482e1af8d0156ed88b5dc2677a0711d46@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 937e79c67740d1d84736730d679f3cb2552f990e upstream.
Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^
Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.
Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.
Fixes: e263bdab9c0e ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a491167fe0cf9f26062462de2a8688b96125d48 ]
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9b8 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e263bdab9c0e8025fb7f41f153709a9cda51f6b6 ]
Beacon buffer for high latency devices does not use DMA. other similar
buffer allocation methods in the driver have already been modified for
high latency path. Fix the beacon buffer allocation left out in the
earlier high latency changes.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[fabio: adapt it to use ar->bus_param.dev_type ]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210818232627.2040121-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9ca70c735ce66fc6a0e02c8b6958434f74ef8de ]
When the code execute this if statement, the value of ret is 0.
However, we can see from the ath10k_warn() log that the value of
ret should be -EINVAL.
Clean up smatch warning:
drivers/net/wireless/ath/ath10k/mac.c:5596 ath10k_add_interface() warn:
missing error code 'ret'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: ccec9038c721 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1621939577-62218-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b55379e343a3472c35f4a1245906db5158cab453 ]
Failed to transmit wmi management frames:
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
CPUx (skb_deuque) CPUy (__skb_queue_tail)
next=list
prev=list
struct sk_buff *skb = skb_peek(list); WRITE_ONCE(newsk->next, next);
WRITE_ONCE(list->qlen, list->qlen - 1);WRITE_ONCE(newsk->prev, prev);
next = skb->next; WRITE_ONCE(next->prev, newsk);
prev = skb->prev; WRITE_ONCE(prev->next, newsk);
skb->next = skb->prev = NULL; list->qlen++;
WRITE_ONCE(next->prev, prev);
WRITE_ONCE(prev->next, next);
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1.c2-00033-QCAHLSWMTPLZ-1
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608618887-8857-1-git-send-email-miaoqing@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7df28718928d08034b36168200d67b558ce36f3d ]
ath10k_debug_fw_stats_request just be called with conf_mutex held,
otherwise the following warning is seen when lock debugging is enabled:
WARNING: CPU: 0 PID: 793 at drivers/net/wireless/ath/ath10k/debug.c:357 ath10k_debug_fw_stats_request+0x12c/0x133 [ath10k_core]
Modules linked in: snd_hda_codec_hdmi designware_i2s snd_hda_intel snd_intel_dspcfg snd_hda_codec i2c_piix4 snd_hwdep snd_hda_core acpi_als kfifo_buf industrialio snd_soc_max98357a snd_soc_adau7002 snd_soc_acp_da7219mx98357_mach snd_soc_da7219 acp_audio_dma ccm xt_MASQUERADE fuse ath10k_pci ath10k_core lzo_rle ath lzo_compress mac80211 zram cfg80211 r8152 mii joydev
CPU: 0 PID: 793 Comm: wpa_supplicant Tainted: G W 5.10.9 #5
Hardware name: HP Grunt/Grunt, BIOS Google_Grunt.11031.104.0 09/05/2019
RIP: 0010:ath10k_debug_fw_stats_request+0x12c/0x133 [ath10k_core]
Code: 1e bb a1 ff ff ff 4c 89 ef 48 c7 c6 d3 31 2e c0 89 da 31 c0 e8 bd f8 ff ff 89 d8 eb 02 31 c0 5b 41 5c 41 5d 41 5e 41 5f 5d c3 <0f> 0b e9 04 ff ff ff 0f 1f 44 00 00 55 48 89 e5 41 56 53 48 89 fb
RSP: 0018:ffffb2478099f7d0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff9e432700cce0 RCX: 11c85cfd6b8e3b00
RDX: ffff9e432700cce0 RSI: ffff9e43127c5668 RDI: ffff9e4318deddf0
RBP: ffffb2478099f7f8 R08: 0000000000000002 R09: 00000003fd7068cc
R10: ffffffffc01b2749 R11: ffffffffc029efaf R12: ffff9e432700c000
R13: ffff9e43127c33e0 R14: ffffb2478099f918 R15: ffff9e43127c33e0
FS: 00007f7ea48e2740(0000) GS:ffff9e432aa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000059aa799ddf38 CR3: 0000000118de2000 CR4: 00000000001506f0
Call Trace:
ath10k_sta_statistics+0x4d/0x270 [ath10k_core]
sta_set_sinfo+0x1be/0xaec [mac80211]
ieee80211_get_station+0x58/0x76 [mac80211]
rdev_get_station+0xf1/0x11e [cfg80211]
nl80211_get_station+0x7f/0x146 [cfg80211]
genl_rcv_msg+0x32e/0x35e
? nl80211_stop_ap+0x19/0x19 [cfg80211]
? nl80211_get_station+0x146/0x146 [cfg80211]
? genl_rcv+0x19/0x36
? genl_rcv+0x36/0x36
netlink_rcv_skb+0x89/0xfb
genl_rcv+0x28/0x36
netlink_unicast+0x169/0x23b
netlink_sendmsg+0x38a/0x402
sock_sendmsg+0x72/0x76
____sys_sendmsg+0x153/0x1cc
? copy_msghdr_from_user+0x5d/0x85
___sys_sendmsg+0x7c/0xb5
? lock_acquire+0x181/0x23d
? syscall_trace_enter+0x15e/0x160
? find_held_lock+0x3d/0xb2
? syscall_trace_enter+0x15e/0x160
? sched_clock_cpu+0x15/0xc6
__sys_sendmsg+0x62/0x9a
do_syscall_64+0x43/0x55
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 4913e675630e ("ath10k: enable rx duration report default for wmi tlv")
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210202144033.1.I9e556f9fb1110d58c31d04a8a1293995fb8bb678@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no caller in tree, so can remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200909135834.38448-1-yuehaibing@huawei.com
|
|
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add ops for reset_tid_config to support reset TID
configuration. This send default configuration to the
target for the TIDs and stores default value in the host.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-5-git-send-email-tamizhr@codeaurora.org
|
|
This patch add ops for set_tid_config to support TID
specific configuration. Station specific TID configuration
will have more priority than vif specific TID configuration.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT service flag introduced
to notify host for TID config support. And RTS_CTS extended tid
configuration support advertised through the service flag
WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT.
TID specific noack configuration requires
aggregation should be disabled and rate for the data TID packets
should be basic rates. So, if the TID already configured
with noack policy then driver will ignore the aggregation
or TX rate related configuration for the same data TID.
In TX rate configuration should be applied with highest
preamble configuration(HT rates should not be applied
for the station which supports vht rates).
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-4-git-send-email-tamizhr@codeaurora.org
|
|
This patch does not have any functional changes.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-3-git-send-email-tamizhr@codeaurora.org
|
|
ath.git patches for v5.10. Major changes:
ath11k
* add support for QCA6390 PCI devices
wcn36xx
* add support for TX ack
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200727193821.GA981@embeddedor
|
|
The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.
The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.
It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.
This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.
This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
|
|
ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES
This patch not effect the info of above 4 bit for all hardware, reason
as below:
NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.
NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.
NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
|
|
Gives drivers the definitions needed to advertise support
for S1G bands.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5c2 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
|
|
When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
Tested-on: QCA9984 PCI 10.4-3.6-00104
Tested-on: QCA9882 PCI 10.2.4-1.0-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591856446-26977-1-git-send-email-vnaralas@codeaurora.org
|
|
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 1807da49733e ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588667015-25490-1-git-send-email-pillair@codeaurora.org
|
|
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f2f875 ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
|
|
For legacy mode, tx bitrate not show correct sometimes, for example:
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 19672 bytes (184 packets)
TX: 9851 bytes (87 packets)
signal: -51 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 2.8 MBit/s
This patch use the tx bitrate info from WMI_TLV_PEER_STATS_INFO_EVENTID
report from firmware, and tx bitrate show correct.
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 13973 bytes (120 packets)
TX: 6737 bytes (57 packets)
signal: -52 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 54.0 MBit/s
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, it is enabled only for
"qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-5-wgong@codeaurora.org
|
|
The rate code and rate kbps report by WMI_TLV_PEER_STATS_INFO_EVENTID
from firmware contains all the bitrate info which include OFDM, CCK,
HT/VHT, and mac80211 need the struct rate_info which include below
parameters:
flags: bitflag of flags from &enum rate_info_flags
mcs: mcs index if struct describes an HT/VHT/HE rate
legacy: bitrate in 100kbit/s for 802.11abg
nss: number of streams (VHT & HE only)
bw: bandwidth (from &enum rate_info_bw)
For OFDM/CCK, its rate kbps indicate the bitrate, for HT/VHT, mac80211
need the above 5 parameters to cacluate the bitrate and show by iw.
After parse the bitrate info, iw show the correct rx bitrate:
localhost ~ # iw wlan0 link
rx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
rx bitrate: 40.5 MBit/s MCS 2 40MHz
rx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 54.0 MBit/s
rx bitrate: 48.0 MBit/s
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-4-wgong@codeaurora.org
|
|
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
|
|
For wmi tlv type, firmware disable peer stats info by default, after
enable it, firmware will report WMI_TLV_PEER_STATS_INFO_EVENTID if
ath10k send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware.
Enable it will only set a flag in firmware, firmware will not report
it without receive request WMI command.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-2-wgong@codeaurora.org
|
|
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
|
|
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
|
|
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
|
|
When station connected to AP, and run TX traffic such as TCP/UDP, and
system enter suspend state, then mac80211 call ath10k_flush with set
drop flag, recently it only send wmi peer flush to firmware and
firmware will flush all pending TX packets, for PCIe, firmware will
indicate the TX packets status to ath10k, and then ath10k indicate to
mac80211 TX complete with the status, then all the packets has been
flushed at this moment. For SDIO chip, it is different, its TX
complete indication is disabled by default, and it has a tx queue in
ath10k, and its tx credit control is enabled, total tx credit is 96,
when its credit is not sufficient, then the packets will buffered in
the tx queue of ath10k, max packets is TARGET_TLV_NUM_MSDU_DESC_HL
which is 1024, for SDIO, when mac80211 call ath10k_flush with set drop
flag, maybe it have pending packets in tx queue of ath10k, and if it
does not have sufficient tx credit, the packets will stay in queue
untill tx credit report from firmware, if it is a noisy environment,
tx speed is low and the tx credit report from firmware will delay more
time, then the num_pending_tx will remain > 0 untill all packets send
to firmware. After the 1st ath10k_flush, mac80211 will call the 2nd
ath10k_flush without set drop flag immediately, then it will call to
ath10k_mac_wait_tx_complete, and it wait untill num_pending_tx become
to 0, in noisy environment, it is esay to wait about near 5 seconds,
then it cause the suspend take long time.
1st and 2nd callstack of ath10k_flush
[ 303.740427] ath10k_sdio mmc1:0001:1: ath10k_flush drop:1, pending:0-0
[ 303.740495] ------------[ cut here ]------------
[ 303.740739] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.740757] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer
[ 303.740914] kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core]
[ 303.741009] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2
[ 303.741027] Hardware name: MediaTek krane sku176 board (DT)
[ 303.741061] Workqueue: events_unbound async_run_entry_fn
[ 303.741086] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 303.741166] pc : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741244] lr : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741260] sp : ffffffdf080e77a0
[ 303.741276] x29: ffffffdf080e77a0 x28: ffffffdef3730040
[ 303.741300] x27: ffffff907c2240a0 x26: ffffffde6ff39afc
[ 303.741321] x25: ffffffdef3730040 x24: ffffff907bf61018
[ 303.741343] x23: ffffff907c2240a0 x22: ffffffde6ff39a50
[ 303.741364] x21: 0000000000000001 x20: ffffffde6ff39a50
[ 303.741385] x19: ffffffde6bac2420 x18: 0000000000017200
[ 303.741407] x17: ffffff907c24a000 x16: 0000000000000037
[ 303.741428] x15: ffffff907b49a568 x14: ffffff907cf332c1
[ 303.741476] x13: 00000000000922e4 x12: 0000000000000000
[ 303.741497] x11: 0000000000000001 x10: 0000000000000007
[ 303.741518] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00
[ 303.741539] x7 : ffffff907ab5e764 x6 : 0000000000000000
[ 303.741560] x5 : 0000000000000080 x4 : 0000000000000001
[ 303.741582] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244
[ 303.741603] x1 : ffffffdf080e74a8 x0 : 0000000000000024
[ 303.741624] Call trace:
[ 303.741701] ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.741941] __ieee80211_flush_queues+0x1dc/0x358 [mac80211]
[ 303.742098] ieee80211_flush_queues+0x34/0x44 [mac80211]
[ 303.742253] ieee80211_set_disassoc+0xc0/0x5ec [mac80211]
[ 303.742399] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211]
[ 303.742535] ieee80211_deauth+0x24/0x30 [mac80211]
[ 303.742720] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211]
[ 303.742849] cfg80211_mlme_down+0x90/0xd0 [cfg80211]
[ 303.742971] cfg80211_disconnect+0x340/0x3a0 [cfg80211]
[ 303.743087] __cfg80211_leave+0xe4/0x17c [cfg80211]
[ 303.743203] cfg80211_leave+0x38/0x50 [cfg80211]
[ 303.743319] wiphy_suspend+0x84/0x5bc [cfg80211]
[ 303.743335] dpm_run_callback+0x170/0x304
[ 303.743346] __device_suspend+0x2dc/0x3e8
[ 303.743356] async_suspend+0x2c/0xb0
[ 303.743370] async_run_entry_fn+0x48/0xf8
[ 303.743383] process_one_work+0x304/0x604
[ 303.743394] worker_thread+0x248/0x3f4
[ 303.743403] kthread+0x120/0x130
[ 303.743416] ret_from_fork+0x10/0x18
[ 303.743812] ath10k_sdio mmc1:0001:1: ath10k_flush drop:0, pending:0-0
[ 303.743858] ------------[ cut here ]------------
[ 303.744057] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744075] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core]
[ 303.744256] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2
[ 303.744273] Hardware name: MediaTek krane sku176 board (DT)
[ 303.744301] Workqueue: events_unbound async_run_entry_fn
[ 303.744325] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 303.744403] pc : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744480] lr : ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.744496] sp : ffffffdf080e77a0
[ 303.744512] x29: ffffffdf080e77a0 x28: ffffffdef3730040
[ 303.744534] x27: ffffff907c2240a0 x26: ffffffde6ff39afc
[ 303.744556] x25: ffffffdef3730040 x24: ffffff907bf61018
[ 303.744577] x23: ffffff907c2240a0 x22: ffffffde6ff39a50
[ 303.744598] x21: 0000000000000000 x20: ffffffde6ff39a50
[ 303.744620] x19: ffffffde6bac2420 x18: 000000000001831c
[ 303.744641] x17: ffffff907c24a000 x16: 0000000000000037
[ 303.744662] x15: ffffff907b49a568 x14: ffffff907cf332c1
[ 303.744683] x13: 00000000000922ea x12: 0000000000000000
[ 303.744704] x11: 0000000000000001 x10: 0000000000000007
[ 303.744747] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00
[ 303.744768] x7 : ffffff907ab5e764 x6 : 0000000000000000
[ 303.744789] x5 : 0000000000000080 x4 : 0000000000000001
[ 303.744810] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244
[ 303.744831] x1 : ffffffdf080e74a8 x0 : 0000000000000024
[ 303.744853] Call trace:
[ 303.744929] ath10k_flush+0x54/0x104 [ath10k_core]
[ 303.745098] __ieee80211_flush_queues+0x1dc/0x358 [mac80211]
[ 303.745277] ieee80211_flush_queues+0x34/0x44 [mac80211]
[ 303.745424] ieee80211_set_disassoc+0x108/0x5ec [mac80211]
[ 303.745569] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211]
[ 303.745706] ieee80211_deauth+0x24/0x30 [mac80211]
[ 303.745853] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211]
[ 303.745979] cfg80211_mlme_down+0x90/0xd0 [cfg80211]
[ 303.746103] cfg80211_disconnect+0x340/0x3a0 [cfg80211]
[ 303.746219] __cfg80211_leave+0xe4/0x17c [cfg80211]
[ 303.746335] cfg80211_leave+0x38/0x50 [cfg80211]
[ 303.746452] wiphy_suspend+0x84/0x5bc [cfg80211]
[ 303.746467] dpm_run_callback+0x170/0x304
[ 303.746477] __device_suspend+0x2dc/0x3e8
[ 303.746487] async_suspend+0x2c/0xb0
[ 303.746498] async_run_entry_fn+0x48/0xf8
[ 303.746510] process_one_work+0x304/0x604
[ 303.746521] worker_thread+0x248/0x3f4
[ 303.746530] kthread+0x120/0x130
[ 303.746542] ret_from_fork+0x10/0x18
one sample's debugging log: it wait 3190 ms(5000 - 1810).
1st ath10k_flush, it has 120 packets in tx queue of ath10k:
<...>-1513 [000] .... 25374.786005: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:1, pending:120-0
<...>-1513 [000] ...1 25374.788375: ath10k_log_warn: ath10k_sdio mmc1:0001:1 ath10k_htt_tx_mgmt_inc_pending htt->num_pending_mgmt_tx:0
<...>-1500 [001] .... 25374.790143: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121
2st ath10k_flush, it has 121 packets in tx queue of ath10k:
<...>-1513 [000] .... 25374.790571: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:0, pending:121-0
<...>-1513 [000] .... 25374.791990: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete state:1 pending:121-0
<...>-1508 [001] .... 25374.792696: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:46
<...>-1508 [001] .... 25374.792700: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:46
<...>-1508 [001] .... 25374.792729: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121
<...>-1508 [001] .... 25374.792937: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:88, count:32, len:49792
<...>-1508 [001] .... 25374.793031: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:75, count:14, len:21784
kworker/u16:0-25773 [003] .... 25374.793701: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:46
<...>-1881 [000] .... 25375.073178: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:24
<...>-1881 [000] .... 25375.073182: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:24
<...>-1881 [000] .... 25375.073429: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:75
<...>-1879 [001] .... 25375.074090: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:24
<...>-1881 [000] .... 25375.074123: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:51, count:24, len:37344
<...>-1879 [001] .... 25375.270126: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:26
<...>-1879 [001] .... 25375.270130: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:26
<...>-1488 [000] .... 25375.270174: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:51
<...>-1488 [000] .... 25375.270529: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:25, count:26, len:40456
<...>-1879 [001] .... 25375.270693: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:26
<...>-1488 [001] .... 25377.775885: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:12
<...>-1488 [001] .... 25377.775890: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:12
<...>-1488 [001] .... 25377.775933: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:25
<...>-1488 [001] .... 25377.776059: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:13, count:12, len:18672
<...>-1879 [001] .... 25377.776100: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:12
<...>-1488 [001] .... 25377.878079: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:15
<...>-1488 [001] .... 25377.878087: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:15
<...>-1879 [000] .... 25377.878323: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:13
<...>-1879 [000] .... 25377.878487: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:0, count:13, len:20228
<...>-1879 [000] .... 25377.878497: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:13
<...>-1488 [001] .... 25377.919927: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:11
<...>-1488 [001] .... 25377.919932: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:13
<...>-1488 [001] .... 25377.919976: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:0
<...>-1881 [000] .... 25377.982645: ath10k_log_warn: ath10k_sdio mmc1:0001:1 HTT_T2H_MSG_TYPE_MGMT_TX_COMPLETION status:0
<...>-1513 [001] .... 25377.982973: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete time_left:1810, pending:0-0
Flush all pending TX packets for the 1st ath10k_flush reduced the wait
time of the 2nd ath10k_flush and then suspend take short time.
This Patch only effect SDIO chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200415233730.10581-1-wgong@codeaurora.org
|
|
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.com
https://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-1-git-send-email-ssreeela@codeaurora.org
|
|
GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
|
|
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b1462f706a1950a355fd086e1c450b6
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Mere overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix some typo:
s/to to/to/
s/even/event/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5ad ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.
This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random
mac address for netdetect case.
iw command:
iw phy0 wowlan enable net-detect net-detect
randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30
freqs 2412 matches ssid foo.
After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41.
WCN3990, QCA9377, QCA6174 PCI also support this feature.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reverts commit 334f5b61a6f29834e881923b98d1e27e5ce9620d.
This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:
err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219
Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da49733e ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is a spelling mistake in a ath10k_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If 'sta->tdls' is false, no cleanup is executed, leading to memory/resource
leaks, e.g., 'arsta->tx_stats'. To fix this issue, perform cleanup before
go to the 'exit' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
