| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0189 Rev= 0.00
S: Manufacturer=ZTE, Incorporated
S: Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/mac80211/rx.c
91535613b609 ("wifi: mac80211: don't drop all unprotected public action frames")
6c02fab72429 ("wifi: mac80211: split ieee80211_drop_unencrypted_mgmt() return value")
Adjacent changes:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c
61471264c018 ("net: ethernet: apm: Convert to platform remove callback returning void")
d2ca43f30611 ("net: xgene: Fix unused xgene_enet_of_match warning for !CONFIG_OF")
net/vmw_vsock/virtio_transport.c
64c99d2d6ada ("vsock/virtio: support to send non-linear skb")
53b08c498515 ("vsock/virtio: initialize the_virtio_vsock before using VQs")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.
The first problem is that the r8152 driver often uses code patterns
similar to this:
x = read_register()
x = x | SOME_BIT;
write_register(x);
...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad18959 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.
It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.
The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.
One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.
On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
things recover.
The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.
On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).
Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.
When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.
This is a no-op change and just a search and replace.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the adapter is unplugged while we're looping in r8153b_ups_en() /
r8153c_ups_en() we could end up looping for 10 seconds (20 ms * 500
loops). Add code similar to what's done in other places in the driver
to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the adapter is unplugged while we're looping in
rtl_phy_patch_request() we could end up looping for 10 seconds (2 ms *
5000 loops). Add code similar to what's done in other places in the
driver to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003f2 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported the following uninit-value access issue [1]:
smsc95xx 1-1:0.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x00000030: -32
smsc95xx 1-1:0.0 (unnamed net_device) (uninitialized): Error reading E2P_CMD
=====================================================
BUG: KMSAN: uninit-value in smsc95xx_reset+0x409/0x25f0 drivers/net/usb/smsc95xx.c:896
smsc95xx_reset+0x409/0x25f0 drivers/net/usb/smsc95xx.c:896
smsc95xx_bind+0x9bc/0x22e0 drivers/net/usb/smsc95xx.c:1131
usbnet_probe+0x100b/0x4060 drivers/net/usb/usbnet.c:1750
usb_probe_interface+0xc75/0x1210 drivers/usb/core/driver.c:396
really_probe+0x506/0xf40 drivers/base/dd.c:658
__driver_probe_device+0x2a7/0x5d0 drivers/base/dd.c:800
driver_probe_device+0x72/0x7b0 drivers/base/dd.c:830
__device_attach_driver+0x55a/0x8f0 drivers/base/dd.c:958
bus_for_each_drv+0x3ff/0x620 drivers/base/bus.c:457
__device_attach+0x3bd/0x640 drivers/base/dd.c:1030
device_initial_probe+0x32/0x40 drivers/base/dd.c:1079
bus_probe_device+0x3d8/0x5a0 drivers/base/bus.c:532
device_add+0x16ae/0x1f20 drivers/base/core.c:3622
usb_set_configuration+0x31c9/0x38c0 drivers/usb/core/message.c:2207
usb_generic_driver_probe+0x109/0x2a0 drivers/usb/core/generic.c:238
usb_probe_device+0x290/0x4a0 drivers/usb/core/driver.c:293
really_probe+0x506/0xf40 drivers/base/dd.c:658
__driver_probe_device+0x2a7/0x5d0 drivers/base/dd.c:800
driver_probe_device+0x72/0x7b0 drivers/base/dd.c:830
__device_attach_driver+0x55a/0x8f0 drivers/base/dd.c:958
bus_for_each_drv+0x3ff/0x620 drivers/base/bus.c:457
__device_attach+0x3bd/0x640 drivers/base/dd.c:1030
device_initial_probe+0x32/0x40 drivers/base/dd.c:1079
bus_probe_device+0x3d8/0x5a0 drivers/base/bus.c:532
device_add+0x16ae/0x1f20 drivers/base/core.c:3622
usb_new_device+0x15f6/0x22f0 drivers/usb/core/hub.c:2589
hub_port_connect drivers/usb/core/hub.c:5440 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5580 [inline]
port_event drivers/usb/core/hub.c:5740 [inline]
hub_event+0x53bc/0x7290 drivers/usb/core/hub.c:5822
process_one_work kernel/workqueue.c:2630 [inline]
process_scheduled_works+0x104e/0x1e70 kernel/workqueue.c:2703
worker_thread+0xf45/0x1490 kernel/workqueue.c:2784
kthread+0x3e8/0x540 kernel/kthread.c:388
ret_from_fork+0x66/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:304
Local variable buf.i225 created at:
smsc95xx_read_reg drivers/net/usb/smsc95xx.c:90 [inline]
smsc95xx_reset+0x203/0x25f0 drivers/net/usb/smsc95xx.c:892
smsc95xx_bind+0x9bc/0x22e0 drivers/net/usb/smsc95xx.c:1131
CPU: 1 PID: 773 Comm: kworker/1:2 Not tainted 6.6.0-rc1-syzkaller-00125-ge42bebf6db29 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/04/2023
Workqueue: usb_hub_wq hub_event
=====================================================
Similar to e9c65989920f ("net: usb: smsc75xx: Fix uninit-value access in
__smsc75xx_read_reg"), this issue is caused because usbnet_read_cmd() reads
less bytes than requested (zero byte in the reproducer). In this case,
'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
sysbot reported similar uninit-value access issue [2]. The root cause is
the same as mentioned above, and this patch addresses it as well.
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Reported-and-tested-by: syzbot+c74c24b43c9ae534f0e0@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+2c97a98a5ba9ea9c23bd@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c74c24b43c9ae534f0e0 [1]
Closes: https://syzkaller.appspot.com/bug?extid=2c97a98a5ba9ea9c23bd [2]
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
net/mac80211/key.c
02e0e426a2fb ("wifi: mac80211: fix error path key leak")
2a8b665e6bcc ("wifi: mac80211: remove key_mtx")
7d6904bf26b9 ("Merge wireless into wireless-next")
https://lore.kernel.org/all/20231012113648.46eea5ec@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/ti/Kconfig
a602ee3176a8 ("net: ethernet: ti: Fix mixed module-builtin object")
98bdeae9502b ("net: cpmac: remove driver to prepare for platform removal")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return a negative error code instead of success.
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/147927f0-9ada-45cc-81ff-75a19dd30b76@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Other implementations of .*get_drvinfo use strscpy so this patch brings
sr_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
...
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-usb-sr9800-c-v1-1-5540832c8ec2@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Other implementations of .*get_drvinfo use strscpy so this patch brings
lan78xx_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-usb-lan78xx-c-v1-1-99d513061dfc@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c55 ("bpf: Fix verifier log for async callback return values")
a923819fb2c5 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot has found an uninit-value bug triggered by the dm9601 driver [1].
This error happens because the variable res is not updated if the call
to dm_read_shared_word returns an error. In this particular case -EPROTO
was returned and res stayed uninitialized.
This can be avoided by checking the return value of dm_read_shared_word
and propagating the error if the read operation failed.
[1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955
Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver")
Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (or adjacent changes of note).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use napi_gro_frags() for the skb of fragments when the work_done is less
than budget.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-434-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A bulk transfer of the USB may contain many packets. And, the total
number of the packets in the bulk transfer may be more than budget.
Originally, only budget packets would be handled by napi_gro_receive(),
and the other packets would be queued in the driver for next schedule.
This patch would break the loop about getting next bulk transfer, when
the budget is exhausted. That is, only the current bulk transfer would
be handled, and the other bulk transfers would be queued for next
schedule. Besides, the packets which are more than the budget in the
current bulk trasnfer would be still queued in the driver, as the
original method.
In addition, a bulk transfer wouldn't contain more than 400 packets, so
the check of queue length is unnecessary. Therefore, I replace it with
WARN_ON_ONCE().
Fixes: cf74eb5a5bc8 ("eth: r8152: try to use a normal budget")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-433-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737
usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032
usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241
usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272
really_probe+0xf20/0x20b0 drivers/base/dd.c:529
driver_probe_device+0x293/0x390 drivers/base/dd.c:701
__device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
__device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554
hub_port_connect drivers/usb/core/hub.c:5208 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5348 [inline]
port_event drivers/usb/core/hub.c:5494 [inline]
hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576
process_one_work+0x1688/0x2140 kernel/workqueue.c:2269
worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415
kthread+0x551/0x590 kernel/kthread.c:292
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293
Local variable ----buf.i87@smsc75xx_bind created at:
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
__smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e4454 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
|
|
The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Antonio Napolitano <anton@polit.no>
Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the serial-core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mario reports that loading r8152 on his system leads to a:
netif_napi_add_weight() called with weight 256
warning getting printed. We don't have any solid data
on why such high budget was chosen, and it may cause
stalls in processing other softirqs and rt threads.
So try to switch back to the default (64) weight.
If this slows down someone's system we should investigate
which part of stopping starting the NAPI poll in this
driver are expensive.
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/all/0bfd445a-81f7-f702-08b0-bd5a72095e49@amd.com/
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230814153521.2697982-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no need for two more variables in hso_serial_write(). Switch to
min_t() and eliminate those.
Furthermore, the 'if-goto' is superfluous as memcpy() of zero count is a
nop. So is addition of zero. So remove the 'if-goto' completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20230810091510.13006-36-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify with the rest of the code. Use size_t for counts and ssize_t for
retval.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data are now typed as u8. Propagate this change to
tty_operations::write().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20230810091510.13006-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/dsa/port.c
9945c1fb03a3 ("net: dsa: fix older DSA drivers using phylink")
a88dd7538461 ("net: dsa: remove legacy_pre_march2020 detection")
https://lore.kernel.org/all/20230731102254.2c9868ca@canb.auug.org.au/
net/xdp/xsk.c
3c5b4d69c358 ("net: annotate data-races around sk->sk_mark")
b7f72a30e9ac ("xsk: introduce wrappers and helpers for supporting multi-buffer in Tx path")
https://lore.kernel.org/all/20230731102631.39988412@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
37b61cda9c16 ("bnxt: don't handle XDP in netpoll")
2b56b3d99241 ("eth: bnxt: handle invalid Tx completions more gracefully")
https://lore.kernel.org/all/20230801101708.1dc7faac@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_fs.c
62da08331f1a ("net/mlx5e: Set proper IPsec source port in L4 selector")
fbd517549c32 ("net/mlx5e: Add function to get IPsec offload namespace")
drivers/net/ethernet/sfc/selftest.c
55c1528f9b97 ("sfc: fix field-spanning memcpy in selftest")
ae9d445cd41f ("sfc: Miscellaneous comment removals")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632
Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.")
Signed-off-by: Ross Maynard <bids.7405@bigpond.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Quectel EM05GV2 (G=global) with vendor ID
0x2c7c and product ID 0x030e
Enabling DTR on this modem was necessary to ensure stable operation.
Patch for usb: serial: option: is also in progress.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030e Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Martin Kohn <m.kohn@welotec.com>
Link: https://lore.kernel.org/r/AM0PR04MB57648219DE893EE04FA6CC759701A@AM0PR04MB5764.eurprd04.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The timer dev->stat_monitor can schedule the delayed work dev->wq and
the delayed work dev->wq can also arm the dev->stat_monitor timer.
When the device is detaching, the net_device will be deallocated. but
the net_device private data could still be dereferenced in delayed work
or timer handler. As a result, the UAF bugs will happen.
One racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_stat_monitor() |
... | lan78xx_disconnect()
lan78xx_defer_kevent() | ...
... | cancel_delayed_work_sync(&dev->wq);
schedule_delayed_work() | ...
(wait some time) | free_netdev(net); //free net_device
lan78xx_delayedwork() |
//use net_device private data |
dev-> //use |
Although we use cancel_delayed_work_sync() to cancel the delayed work
in lan78xx_disconnect(), it could still be scheduled in timer handler
lan78xx_stat_monitor().
Another racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_delayedwork |
mod_timer() | lan78xx_disconnect()
| cancel_delayed_work_sync()
(wait some time) | if (timer_pending(&dev->stat_monitor))
| del_timer_sync(&dev->stat_monitor);
lan78xx_stat_monitor() | ...
lan78xx_defer_kevent() | free_netdev(net); //free
//use net_device private data|
dev-> //use |
Although we use del_timer_sync() to delete the timer, the function
timer_pending() returns 0 when the timer is activated. As a result,
the del_timer_sync() will not be executed and the timer could be
re-armed.
In order to mitigate this bug, We use timer_shutdown_sync() to shutdown
the timer and then use cancel_delayed_work_sync() to cancel the delayed
work. As a result, the net_device could be deallocated safely.
What's more, the dev->flags is set to EVENT_DEV_DISCONNECT in
lan78xx_disconnect(). But it could still be set to EVENT_STAT_UPDATE
in lan78xx_stat_monitor(). So this patch put the set_bit() behind
timer_shutdown_sync().
Fixes: 77dfff5bb7e2 ("lan78xx: Fix race condition in disconnect handling")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PLA_BP_0 ~ PLA_BP_15 (0xfc28 ~ 0xfc46) are continuous registers, so we
could combine the control transfers into one control transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-419-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce the control transfer if all bytes of first or the last DWORD are
written.
The original method is to split the control transfer into three parts
(the first DWORD, middle continuous data, and the last DWORD). However,
they could be combined if whole bytes of the first DWORD or last DWORD
are written. That is, the first DWORD or the last DWORD could be combined
with the middle continuous data, if the byte_en is 0xff.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-418-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The syzbot fuzzer identified a problem in the usbnet driver:
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 754 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 754 Comm: kworker/0:2 Not tainted 6.4.0-rc7-syzkaller-00014-g692b7dc87ca6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Workqueue: mld mld_ifc_work
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
Code: 7c 24 18 e8 2c b4 5b fb 48 8b 7c 24 18 e8 42 07 f0 fe 41 89 d8 44 89 e1 4c 89 ea 48 89 c6 48 c7 c7 a0 c9 fc 8a e8 5a 6f 23 fb <0f> 0b e9 58 f8 ff ff e8 fe b3 5b fb 48 81 c5 c0 05 00 00 e9 84 f7
RSP: 0018:ffffc9000463f568 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: ffff88801eb28000 RSI: ffffffff814c03b7 RDI: 0000000000000001
RBP: ffff8881443b7190 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000003
R13: ffff88802a77cb18 R14: 0000000000000003 R15: ffff888018262500
FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556a99c15a18 CR3: 0000000028c71000 CR4: 0000000000350ef0
Call Trace:
<TASK>
usbnet_start_xmit+0xfe5/0x2190 drivers/net/usb/usbnet.c:1453
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3578 [inline]
dev_hard_start_xmit+0x187/0x700 net/core/dev.c:3594
...
This bug is caused by the fact that usbnet trusts the bulk endpoint
addresses its probe routine receives in the driver_info structure, and
it does not check to see that these endpoints actually exist and have
the expected type and directions.
The fix is simply to add such a check.
Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add CDC-ECM support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.5 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add RmNet support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230626125336.3127-1-davide.tronchin.94@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/mlx5/driver.h
617f5db1a626 ("RDMA/mlx5: Fix affinity assignment")
dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
https://lore.kernel.org/all/20230613125939.595e50b8@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
47867f0a7e83 ("selftests: mptcp: join: skip check if MIB counter not supported")
425ba803124b ("selftests: mptcp: join: support RM_ADDR for used endpoints or not")
45b1a1227a7a ("mptcp: introduces more address related mibs")
0639fa230a21 ("selftests: mptcp: add explicit check for new mibs")
https://lore.kernel.org/netdev/20230609-upstream-net-20230610-mptcp-selftests-support-old-kernels-part-3-v1-0-2896fe2ee8a3@tessares.net/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move declarations into include/net/gso.h and code into net/core/gso.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230608191738.3947077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This module has for a long time not been limited to iPhone <= 3GS.
Update description to match the actual state of the driver.
Remove dead link from 2010, instead reference an existing userspace
iOS device pairing implementation as part of libimobiledevice.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent iOS releases support CDC NCM encapsulation on RX. This mode is
the default on macOS and Windows. In this mode, an iOS device may include
one or more Ethernet frames inside a single URB.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver. When reconnecting such a device
from a macOS/Windows machine to a Linux host, the device stays in
NCM mode, making it unusable with the legacy ipheth driver code.
To correctly support such a device, the driver has to either support
the NCM mode too, or put the device back into legacy mode.
To match the behaviour of the macOS/Windows driver, and since there
is no documented control command to revert to legacy mode, implement
NCM support. The device is attempted to be put into NCM mode by default,
and falls back to legacy mode if the attempt fails.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The behaviour of the official iOS tethering driver on macOS is to not
transmit any trailing padding at the end of URBs. This is applicable
to both NCM and legacy modes, including older devices.
Adapt the driver to not include trailing padding in TX URBs, matching
the behaviour of the official macOS driver.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cleanup precedure in ipheth_probe will attempt to free a
NULL pointer in dev->ctrl_buf if the memory allocation for
this buffer is not successful. While kfree ignores NULL pointers,
and the existing code is safe, it is a better design to rearrange
the goto labels and avoid this.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Compal RXM-G1 which is based on Qualcomm SDX55 chip.
This patch adds support for two compositions:
0x9091: DIAG + MODEM + QMI_RMNET + ADB
0x90db: DIAG + DUN + RMNET + DPL + QDSS(Trace) + ADB
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=05c6 ProdID=9091 Rev= 4.14
S: Manufacturer=QCOM
S: Product=SDXPRAIRIE-MTP _SN:719AB680
S: SerialNumber=719ab680
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=05c6 ProdID=90db Rev= 4.14
S: Manufacturer=QCOM
S: Product=SDXPRAIRIE-MTP _SN:719AB680
S: SerialNumber=719ab680
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Wes Huang <wes.huang@moxa.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20230608030141.3546-1-wes.huang@moxa.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BM818 is based on Qualcomm MDM9607 chipset.
Fixes: 9a07406b00cd ("net: usb: qmi_wwan: Add the BroadMobi BM818 card")
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20230526-bm818-dtr-v1-1-64bbfa6ba8af@puri.sm
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d3364f ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
