summaryrefslogtreecommitdiff
path: root/drivers/net/sfc/mdio_10g.c
AgeCommit message (Collapse)AuthorFilesLines
2009-11-30sfc: Update version, copyright dates, authorsBen Hutchings1-1/+1
This driver has been mostly rewritten since Michael Brown's initial work, so swap the order of the authors. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-30sfc: Rename falcon.h to nic.hBen Hutchings1-1/+1
nic.h is no longer specific to Falcon. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-30sfc: Remove static PHY data and enumerationsBen Hutchings1-2/+2
New NICs have firmware managing the PHY, and we will discover the PHY capabilities at run-time. Replace the static data with probe() and test_name() operations. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-30sfc: Extend loopback mode enumerationBen Hutchings1-2/+2
New NICs and PHYs support a wider variety of loopback modes. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-30sfc: Refactor link configurationBen Hutchings1-14/+27
Refactor PHY, MAC and NIC configuration operations so that the existing link configuration can be re-pushed with: efx->phy_op->reconfigure(efx); efx->mac_op->reconfigure(efx); and a new configuration with: efx->nic_op->reconfigure_port(efx); (plus locking and error-checking). We have not held the link settings in software (aside from flow control), and have relied on asking the hardware what they are. This is a problem because in some cases the hardware may no longer be in a state to tell us. In particular, if an entire multi-port board is reset through one port, the driver bindings to other ports have no chance to save settings before recovering. We only actually need to keep track of the autonegotiation settings, so add an ethtool advertising mask to struct efx_nic, initialise it in PHY init and update it as necessary. Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and struct ethtool_cmd. Much of this was done by Steve Hodgson <shodgson@solarflare.com>. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-24sfc: Remove unused code for non-autoneg speed/duplex switchingBen Hutchings1-69/+39
The only multi-speed PHY driver using this is 10Xpress, and it does not support non-autoneg operation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-24sfc: Merge efx_fc_resolve() into efx_mdio_get_pause()Ben Hutchings1-4/+8
efx_fc_resolve() is specific to MDIO and is not used by any other function. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-24sfc: Remove boards.h, moving last remaining declaration to falcon.hBen Hutchings1-1/+0
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-30sfc: Use generic MDIO flow control auto-negotiation functionsBen Hutchings1-21/+1
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-30sfc: Use generic MDIO functions and definitionsBen Hutchings1-295/+84
Make use of the newly-added generic MDIO clause 45 support and remove redundant definitions. Add an 'efx_' prefix to the remaining driver-specific MDIO functions and remove arguments which are redundant with efx->mdio.prtad. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Fix reporting of PHY idBen Hutchings1-0/+15
Shuffle bits of the OUI into the conventional written order. Replace PHY id component macros with functions. Zero-pad PHY id components in log messages. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Fix test for MDIO read failureBen Hutchings1-6/+7
Commit 27dd2caca4eabe7c13a052b7456495ba75535e6a changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFX7101/SFT9001: Fix AN advertisementsBen Hutchings1-98/+79
All 10Xpress PHYs require autonegotiation all the time; enforce this in the set_settings() method and do not treat it as a workaround. Remove claimed support for 100M HD mode since it is not supported by current firmware. Do not set speed override bits when AN is enabled, and do not use register 1.49192 for AN configuration as it can override what we set elsewhere. Always set the AN selector bits to 1 (802.3). Fix confusion between Next Page and Extended Next Page. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: Test for PHYXS faults whenever we cannot test link state bitsSteve Hodgson1-7/+9
Depending on the loopback mode, there may be no pertinent link state bits. In this case we test the PHYXS RX fault bit instead. Make sure to do this in all cases where there are no link state bits. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFT9001: Fix speed reporting in 1G PHY loopbackSteve Hodgson1-0/+4
Instead of disabling AN in loopback, just prevent restarting AN and override the speed in sft9001_get_settings(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings1-7/+10
When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Fix unreliable link detection in some loopback modesBen Hutchings1-9/+13
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-13sfc: Implement auto-negotiationBen Hutchings1-71/+277
Add infrastructure for auto-negotiation of speed, duplex and flow control. When using 10Xpress, auto-negotiate flow control. While we're at it, clean up the code to warn when partner is not 10GBASE-T capable. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-13sfc: Clean up MDIO flag settingBen Hutchings1-59/+28
We often want to set or clear a flag in an MDIO register, but avoid writing if no change is required since this can have side-effects. Encapsulate this in a function, mdio_clause45_set_flag(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-13sfc: Add support for MMDs numbered >15Ben Hutchings1-11/+13
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of reading just DEVS0. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-06sfc: Use lm87 and lm90 drivers for board temperature/power monitoringBen Hutchings1-0/+35
Add board monitoring to periodic work whenever link is down. For SFE4001, report when a fault has caused the PHY to turn off. For SFE4002, switch XFP PHY into low-power state in case of a fault. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03sfc: Make PHY flash mode a device attribute, not a module parameterBen Hutchings1-1/+3
This allows updating PHY firmware for one interface without removing all other interfaces handled by the driver. Replace tx_disabled flags and 10Xpress status enumeration with flags in enum efx_phy_mode. Prevent an interface from being brought up while in PHY flash mode. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03sfc: Use explicit bool for boolean variables, parameters and return valuesBen Hutchings1-7/+5
Replace (cond ? 1 : 0) with cond or !!cond as appropriate, and (cond ? 0 : 1) with !cond. Remove some redundant boolean temporaries. Rename one field that looks like a flag but isn't. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-13[netdrvr] sfc: sfc: Add self-test supportBen Hutchings1-0/+78
Add a set of self-tests accessible thorugh ethtool. Add hardware loopback and TX disable control code to support them. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29New driver "sfc" for Solarstorm SFC4000 controller.Ben Hutchings1-0/+282
The driver supports the 10Xpress PHY and XFP modules on our reference designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and SMC10GPCIe-10BT. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-30 11:02:58 +0300