summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2024-08-15net: hns3: use correct release function during uninitializationPeiyang Wang1-1/+1
pci_request_regions is called to apply for PCI I/O and memory resources when the driver is initialized, Therefore, when the driver is uninstalled, pci_release_regions should be used to release PCI I/O and memory resources instead of pci_release_mem_regions is used to release memory reasouces only. Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-15net: hns3: void array out of bound when loop tnl_numPeiyang Wang1-3/+3
When query reg inf of SSU, it loops tnl_num times. However, tnl_num comes from hardware and the length of array is a fixed value. To void array out of bound, make sure the loop time is not greater than the length of array Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-15net: hns3: fix a deadlock problem when config TC during resettingJie Wang1-0/+3
When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it. Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-15net: hns3: use the user's cfg after resetPeiyang Wang2-6/+21
Consider the followed case that the user change speed and reset the net interface. Before the hw change speed successfully, the driver get old old speed from hw by timer task. After reset, the previous speed is config to hw. As a result, the new speed is configed successfully but lost after PF reset. The followed pictured shows more dirrectly. +------+ +----+ +----+ | USER | | PF | | HW | +---+--+ +-+--+ +-+--+ | ethtool -s 100G | | +------------------>| set speed 100G | | +--------------------->| | | set successfully | | |<---------------------+---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 200G | | changing event | ethtool --reset |<---------------------+ | (100G) +------------------>| cfg previous speed |<--+ | | after reset (200G) | | +--------------------->| | | +---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 100G | | changing event | |<---------------------+ | (200G) | | |<--+ | |query cfg (timer task)| | +--------------------->| | | return 200G | | |<---------------------+ | | | v v v This patch save new speed if hw change speed successfully, which will be used after reset successfully. Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary") Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-15net: hns3: fix wrong use of semaphore upJie Wang2-4/+4
Currently, if hns3 PF or VF FLR reset failed after five times retry, the reset done process will directly release the semaphore which has already released in hclge_reset_prepare_general. This will cause down operation fail. So this patch fixes it by adding reset state judgement. The up operation is only called after successful PF FLR reset. Fixes: 8627bdedc435 ("net: hns3: refactor the precedure of PF FLR") Fixes: f28368bb4542 ("net: hns3: refactor the procedure of VF FLR") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-15net: thunder_bgx: Fix netdev structure allocationMarc Zyngier1-9/+21
Commit 94833addfaba ("net: thunderx: Unembed netdev structure") had a go at dynamically allocating the netdev structures for the thunderx_bgx driver. This change results in my ThunderX box catching fire (to be fair, it is what it does best). The issues with this change are that: - bgx_lmac_enable() is called *after* bgx_acpi_register_phy() and bgx_init_of_phy(), both expecting netdev to be a valid pointer. - bgx_init_of_phy() populates the MAC addresses for *all* LMACs attached to a given BGX instance, and thus needs netdev for each of them to have been allocated. There is a few things to be said about how the driver mixes LMAC and BGX states which leads to this sorry state, but that's beside the point. To address this, go back to a situation where all netdev structures are allocated before the driver starts relying on them, and move the freeing of these structures to driver removal. Someone brave enough can always go and restructure the driver if they want. Fixes: 94833addfaba ("net: thunderx: Unembed netdev structure") Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: Breno Leitao <leitao@debian.org> Cc: Sunil Goutham <sgoutham@marvell.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Breno Leitao <leitao@debian.org> Link: https://patch.msgid.link/20240812141322.1742918-1-maz@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-13mlxbf_gige: disable RX filters until RX path initializedDavid Thompson4-6/+64
A recent change to the driver exposed a bug where the MAC RX filters (unicast MAC, broadcast MAC, and multicast MAC) are configured and enabled before the RX path is fully initialized. The result of this bug is that after the PHY is started packets that match these MAC RX filters start to flow into the RX FIFO. And then, after rx_init() is completed, these packets will go into the driver RX ring as well. If enough packets are received to fill the RX ring (default size is 128 packets) before the call to request_irq() completes, the driver RX function becomes stuck. This bug is intermittent but is most likely to be seen where the oob_net0 interface is connected to a busy network with lots of broadcast and multicast traffic. All the MAC RX filters must be disabled until the RX path is ready, i.e. all initialization is done and all the IRQs are installed. Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized") Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-13net: mana: Fix doorbell out of order violation and avoid unnecessary ↵Long Li1-9/+15
doorbell rings After napi_complete_done() is called when NAPI is polling in the current process context, another NAPI may be scheduled and start running in softirq on another CPU and may ring the doorbell before the current CPU does. When combined with unnecessary rings when there is no need to arm the CQ, it triggers error paths in the hardware. This patch fixes this by calling napi_complete_done() after doorbell rings. It limits the number of unnecessary rings when there is no need to arm. MANA hardware specifies that there must be one doorbell ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical workloads, the 4 CQ wraparounds proves to be big enough that it rarely exceeds this limit before all the napi weight is consumed. To implement this, add a per-CQ counter cq->work_done_since_doorbell, and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ. Cc: stable@vger.kernel.org Fixes: e1b5683ff62e ("net: mana: Move NAPI from EQ to CQ") Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Long Li <longli@microsoft.com> Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-08-13net: macb: Use rcu_dereference() for idev->ifa_list in macb_suspend().Kuniyuki Iwashima1-2/+2
In macb_suspend(), idev->ifa_list is fetched with rcu_access_pointer() and later the pointer is dereferenced as ifa->ifa_local. So, idev->ifa_list must be fetched with rcu_dereference(). Fixes: 0cb8de39a776 ("net: macb: Add ARP support to WOL") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20240808040021.6971-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-12net: ethernet: mtk_wed: fix use-after-free panic in mtk_wed_setup_tc_block_cb()Zheng Zhang1-2/+4
When there are multiple ap interfaces on one band and with WED on, turning the interface down will cause a kernel panic on MT798X. Previously, cb_priv was freed in mtk_wed_setup_tc_block() without marking NULL,and mtk_wed_setup_tc_block_cb() didn't check the value, too. Assign NULL after free cb_priv in mtk_wed_setup_tc_block() and check NULL in mtk_wed_setup_tc_block_cb(). ---------- Unable to handle kernel paging request at virtual address 0072460bca32b4f5 Call trace: mtk_wed_setup_tc_block_cb+0x4/0x38 0xffffffc0794084bc tcf_block_playback_offloads+0x70/0x1e8 tcf_block_unbind+0x6c/0xc8 ... --------- Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support") Signed-off-by: Zheng Zhang <everything411@qq.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-12net: mana: Fix RX buf alloc_size alignment and atomic op panicHaiyang Zhang1-1/+5
The MANA driver's RX buffer alloc_size is passed into napi_build_skb() to create SKB. skb_shinfo(skb) is located at the end of skb, and its alignment is affected by the alloc_size passed into napi_build_skb(). The size needs to be aligned properly for better performance and atomic operations. Otherwise, on ARM64 CPU, for certain MTU settings like 4000, atomic operations may panic on the skb_shinfo(skb)->dataref due to alignment fault. To fix this bug, add proper alignment to the alloc_size calculation. Sample panic info: [ 253.298819] Unable to handle kernel paging request at virtual address ffff000129ba5cce [ 253.300900] Mem abort info: [ 253.301760] ESR = 0x0000000096000021 [ 253.302825] EC = 0x25: DABT (current EL), IL = 32 bits [ 253.304268] SET = 0, FnV = 0 [ 253.305172] EA = 0, S1PTW = 0 [ 253.306103] FSC = 0x21: alignment fault Call trace: __skb_clone+0xfc/0x198 skb_clone+0x78/0xe0 raw6_local_deliver+0xfc/0x228 ip6_protocol_deliver_rcu+0x80/0x500 ip6_input_finish+0x48/0x80 ip6_input+0x48/0xc0 ip6_sublist_rcv_finish+0x50/0x78 ip6_sublist_rcv+0x1cc/0x2b8 ipv6_list_rcv+0x100/0x150 __netif_receive_skb_list_core+0x180/0x220 netif_receive_skb_list_internal+0x198/0x2a8 __napi_poll+0x138/0x250 net_rx_action+0x148/0x330 handle_softirqs+0x12c/0x3a0 Cc: stable@vger.kernel.org Fixes: 80f6215b450e ("net: mana: Add support for jumbo frame") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-12net: axienet: Fix register defines comment descriptionRadhey Shyam Pandey1-8/+8
In axiethernet header fix register defines comment description to be inline with IP documentation. It updates MAC configuration register, MDIO configuration register and frame filter control description. Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-11Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-qDavid S. Miller4-16/+75
ueue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (igc) This series contains updates to igc driver only. Faizal adjusts the size of the MAC internal buffer on i226 devices to resolve an errata for leaking packet transmits. He also corrects a condition in which qbv_config_change_errors are incorrectly counted. Lastly, he adjusts the conditions for resetting the adapter when changing TSN Tx mode and corrects the conditions in which gtxoffset register is set. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-11net: ethernet: use ip_hdrlen() instead of bit shiftMoon Yeounsu1-6/+4
`ip_hdr(skb)->ihl << 2` is the same as `ip_hdrlen(skb)` Therefore, we should use a well-defined function not a bit shift to find the header length. It also compresses two lines to a single line. Signed-off-by: Moon Yeounsu <yyyynoom@gmail.com> Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-08-10net/mlx5e: Fix queue stats access to non-existing channels splatGal Pressman1-1/+4
The queue stats API queries the queues according to the real_num_[tr]x_queues, in case the device is down and channels were not yet created, don't try to query their statistics. To trigger the panic, run this command before the interface is brought up: ./cli.py --spec ../../../Documentation/netlink/specs/netdev.yaml --dump qstats-get --json '{"ifindex": 4}' BUG: kernel NULL pointer dereference, address: 0000000000000c00 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 3 UID: 0 PID: 977 Comm: python3 Not tainted 6.10.0+ #40 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x14e/0x3d0 ? exc_page_fault+0x73/0x130 ? asm_exc_page_fault+0x22/0x30 ? mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] netdev_nl_stats_by_netdev+0x2a6/0x4c0 ? __rmqueue_pcplist+0x351/0x6f0 netdev_nl_qstats_get_dumpit+0xc4/0x1b0 genl_dumpit+0x2d/0x80 netlink_dump+0x199/0x410 __netlink_dump_start+0x1aa/0x2c0 genl_family_rcv_msg_dumpit+0x94/0xf0 ? __pfx_genl_start+0x10/0x10 ? __pfx_genl_dumpit+0x10/0x10 ? __pfx_genl_done+0x10/0x10 genl_rcv_msg+0x116/0x2b0 ? __pfx_netdev_nl_qstats_get_dumpit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x21a/0x340 netlink_sendmsg+0x1f4/0x440 __sys_sendto+0x1b6/0x1c0 ? do_sock_setsockopt+0xc3/0x180 ? __sys_setsockopt+0x60/0xb0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x50/0x110 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f43757132b0 Code: c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 1d 45 31 c9 45 31 c0 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 68 c3 0f 1f 80 00 00 00 00 41 54 48 83 ec 20 RSP: 002b:00007ffd258da048 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007ffd258da0f8 RCX: 00007f43757132b0 RDX: 000000000000001c RSI: 00007f437464b850 RDI: 0000000000000003 RBP: 00007f4375085de0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f43751a6147 </TASK> Modules linked in: netconsole xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core zram zsmalloc mlx5_core fuse [last unloaded: netconsole] CR2: 0000000000000c00 ---[ end trace 0000000000000000 ]--- RIP: 0010:mlx5e_get_queue_stats_rx+0x3c/0xb0 [mlx5_core] Code: fc 55 48 63 ee 53 48 89 d3 e8 40 3d 70 e1 85 c0 74 58 4c 89 ef e8 d4 07 04 00 84 c0 75 41 49 8b 84 24 f8 39 00 00 48 8b 04 e8 <48> 8b 90 00 0c 00 00 48 03 90 40 0a 00 00 48 89 53 08 48 8b 90 08 RSP: 0018:ffff888116be37d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888116be3868 RCX: 0000000000000004 RDX: ffff88810ada4000 RSI: 0000000000000000 RDI: ffff888109df09c0 RBP: 0000000000000000 R08: 0000000000000004 R09: 0000000000000004 R10: ffff88813461901c R11: ffffffffffffffff R12: ffff888109df0000 R13: ffff888109df09c0 R14: ffff888116be38d0 R15: 0000000000000000 FS: 00007f4375d5c740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000c00 CR3: 0000000106ada006 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 7b66ae536a78 ("net/mlx5e: Add per queue netdev-genl stats") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Joe Damato <jdamato@fastly.com> Link: https://patch.msgid.link/20240808144107.2095424-6-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-10net/mlx5e: Correctly report errors for ethtool rx flowsCosmin Ratiu1-1/+1
Previously, an ethtool rx flow with no attrs would not be added to the NIC as it has no rules to configure the hw with, but it would be reported as successful to the caller (return code 0). This is confusing for the user as ethtool then reports "Added rule $num", but no rule was actually added. This change corrects that by instead reporting these wrong rules as -EINVAL. Fixes: b29c61dac3a2 ("net/mlx5e: Ethtool steering flow validation refactoring") Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-10net/mlx5e: Take state lock during tx timeout reporterDragos Tatulea1-0/+2
mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag. Fixes: eab0da38912e ("net/mlx5e: Fix possible deadlock on mlx5e_tx_timeout_work") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Link: https://lore.kernel.org/all/ZplpKq8FKi3vwfxv@gmail.com/T/ Reviewed-by: Breno Leitao <leitao@debian.org> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-4-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-10net/mlx5e: SHAMPO, Increase timeout to improve latencyDragos Tatulea4-14/+17
During latency tests (netperf TCP_RR) a 30% degradation of HW GRO vs SW GRO was observed. This is due to SHAMPO triggering timeout filler CQEs instead of delivering the CQE for the packet. Having a short timeout for SHAMPO doesn't bring any benefits as it is the driver that does the merging, not the hardware. On the contrary, it can have a negative impact: additional filler CQEs are generated due to the timeout. As there is no way to disable this timeout, this change sets it to the maximum value. Instead of using the packet_merge.timeout parameter which is also used for LRO, set the value directly when filling in the rest of the SHAMPO parameters in mlx5e_build_rq_param(). Fixes: 99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-3-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-10net/mlx5: SD, Do not query MPIR register if no sd_groupTariq Toukan1-9/+9
Unconditionally calling the MPIR query on BF separate mode yields the FW syndrome below [1]. Do not call it unless admin clearly specified the SD group, i.e. expressing the intention of using the multi-PF netdev feature. This fix covers cases not covered in commit fca3b4791850 ("net/mlx5: Do not query MPIR on embedded CPU function"). [1] mlx5_cmd_out_err:808:(pid 8267): ACCESS_REG(0x805) op_mod(0x1) failed, status bad system state(0x4), syndrome (0x685f19), err(-5) Fixes: 678eb448055a ("net/mlx5: SD, Implement basic query and instantiation") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20240808144107.2095424-2-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08Merge branch '100GbE' of ↵Jakub Kicinski3-4/+10
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-08-07 (ice) This series contains updates to ice driver only. Grzegorz adds IRQ synchronization call before performing reset and prevents writing to hardware when it is resetting. Mateusz swaps incorrect assignment of FEC statistics. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix incorrect assigns of FEC counts ice: Skip PTP HW writes during PTP reset procedure ice: Fix reset handler ==================== Link: https://patch.msgid.link/20240807224521.3819189-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08net: ethtool: fix off-by-one error in max RSS context IDsEdward Cree1-1/+1
Both ethtool_ops.rxfh_max_context_id and the default value used when it's not specified are supposed to be exclusive maxima (the former is documented as such; the latter, U32_MAX, cannot be used as an ID since it equals ETH_RXFH_CONTEXT_ALLOC), but xa_alloc() expects an inclusive maximum. Subtract one from 'limit' to produce an inclusive maximum, and pass that to xa_alloc(). Increase bnxt's max by one to prevent a (very minor) regression, as BNXT_MAX_ETH_RSS_CTX is an inclusive max. This is safe since bnxt is not actually hard-limited; BNXT_MAX_ETH_RSS_CTX is just a leftover from old driver code that managed context IDs itself. Rename rxfh_max_context_id to rxfh_max_num_contexts to make its semantics (hopefully) more obvious. Fixes: 847a8ab18676 ("net: ethtool: let the core choose RSS context IDs") Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://patch.msgid.link/5a2d11a599aa5b0cc6141072c01accfb7758650c.1723045898.git.ecree.xilinx@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08net: fec: Stop PPS on driver removeCsókás, Bence1-0/+3
PPS was not stopped in `fec_ptp_stop()`, called when the adapter was removed. Consequentially, you couldn't safely reload the driver with the PPS signal on. Fixes: 32cba57ba74b ("net: fec: introduce fec_ptp_stop and use in probe fail path") Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/netdev/CAOMZO5BzcZR8PwKKwBssQq_wAGzVgf1ffwe_nhpQJjviTdxy-w@mail.gmail.com/T/#m01dcb810bfc451a492140f6797ca77443d0cb79f Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20240807080956.2556602-1-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilitiesFlorian Fainelli1-9/+5
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC, while others might be only supported by the PHY. Make sure that the .get_wol() returns the union of both rather than only that of the PHY if the PHY supports Wake-on-LAN. Fixes: 7e400ff35cbe ("net: bcmgenet: Add support for PHY-based Wake-on-LAN") Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20240806175659.3232204-1-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08net: stmmac: dwmac4: fix PCS duplex mode decodeRussell King (Oracle)2-3/+1
dwmac4 was decoding the duplex mode from the GMAC_PHYIF_CONTROL_STATUS register incorrectly, using GMAC_PHYIF_CTRLSTATUS_LNKMOD_MASK (value 1) rather than GMAC_PHYIF_CTRLSTATUS_LNKMOD (bit 16). Fix this. Fixes: 70523e639bf8c ("drivers: net: stmmac: reworking the PCS code.") Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1sbJvd-001rGD-E3@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08idpf: fix UAFs when destroying the queuesAlexander Lobakin2-35/+13
The second tagged commit started sometimes (very rarely, but possible) throwing WARNs from net/core/page_pool.c:page_pool_disable_direct_recycling(). Turned out idpf frees interrupt vectors with embedded NAPIs *before* freeing the queues making page_pools' NAPI pointers lead to freed memory before these pools are destroyed by libeth. It's not clear whether there are other accesses to the freed vectors when destroying the queues, but anyway, we usually free queue/interrupt vectors only when the queues are destroyed and the NAPIs are guaranteed to not be referenced anywhere. Invert the allocation and freeing logic making queue/interrupt vectors be allocated first and freed last. Vectors don't require queues to be present, so this is safe. Additionally, this change allows to remove that useless queue->q_vector pointer cleanup, as vectors are still valid when freeing the queues (+ both are freed within one function, so it's not clear why nullify the pointers at all). Fixes: 1c325aac10a8 ("idpf: configure resources for TX queues") Fixes: 90912f9f4f2d ("idpf: convert header split mode to libeth + napi_build_skb()") Reported-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08idpf: fix memleak in vport interrupt configurationMichal Kubiak1-11/+8
The initialization of vport interrupt consists of two functions: 1) idpf_vport_intr_init() where a generic configuration is done 2) idpf_vport_intr_req_irq() where the irq for each q_vector is requested. The first function used to create a base name for each interrupt using "kasprintf()" call. Unfortunately, although that call allocated memory for a text buffer, that memory was never released. Fix this by removing creating the interrupt base name in 1). Instead, always create a full interrupt name in the function 2), because there is no need to create a base name separately, considering that the function 2) is never called out of idpf_vport_intr_init() context. Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport") Cc: stable@vger.kernel.org # 6.7 Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08idpf: fix memory leaks and crashes while performing a soft resetAlexander Lobakin1-15/+15
The second tagged commit introduced a UAF, as it removed restoring q_vector->vport pointers after reinitializating the structures. This is due to that all queue allocation functions are performed here with the new temporary vport structure and those functions rewrite the backpointers to the vport. Then, this new struct is freed and the pointers start leading to nowhere. But generally speaking, the current logic is very fragile. It claims to be more reliable when the system is low on memory, but in fact, it consumes two times more memory as at the moment of running this function, there are two vports allocated with their queues and vectors. Moreover, it claims to prevent the driver from running into "bad state", but in fact, any error during the rebuild leaves the old vport in the partially allocated state. Finally, if the interface is down when the function is called, it always allocates a new queue set, but when the user decides to enable the interface later on, vport_open() allocates them once again, IOW there's a clear memory leak here. Just don't allocate a new queue set when performing a reset, that solves crashes and memory leaks. Readd the old queue number and reopen the interface on rollback - that solves limbo states when the device is left disabled and/or without HW queues enabled. Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks") Fixes: e4891e4687c8 ("idpf: split &idpf_queue into 4 strictly-typed queue structures") Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240806220923.3359860-2-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-08bnxt_en : Fix memory out-of-bounds in bnxt_fill_hw_rss_tbl()Michael Chan1-6/+7
A recent commit has modified the code in __bnxt_reserve_rings() to set the default RSS indirection table to default only when the number of RX rings is changing. While this works for newer firmware that requires RX ring reservations, it causes the regression on older firmware not requiring RX ring resrvations (BNXT_NEW_RM() returns false). With older firmware, RX ring reservations are not required and so hw_resc->resv_rx_rings is not always set to the proper value. The comparison: if (old_rx_rings != bp->hw_resc.resv_rx_rings) in __bnxt_reserve_rings() may be false even when the RX rings are changing. This will cause __bnxt_reserve_rings() to skip setting the default RSS indirection table to default to match the current number of RX rings. This may later cause bnxt_fill_hw_rss_tbl() to use an out-of-range index. We already have bnxt_check_rss_tbl_no_rmgr() to handle exactly this scenario. We just need to move it up in bnxt_need_reserve_rings() to be called unconditionally when using older firmware. Without the fix, if the TX rings are changing, we'll skip the bnxt_check_rss_tbl_no_rmgr() call and __bnxt_reserve_rings() may also skip the bnxt_set_dflt_rss_indir_tbl() call for the reason explained in the last paragraph. Without setting the default RSS indirection table to default, it causes the regression: BUG: KASAN: slab-out-of-bounds in __bnxt_hwrm_vnic_set_rss+0xb79/0xe40 Read of size 2 at addr ffff8881c5809618 by task ethtool/31525 Call Trace: __bnxt_hwrm_vnic_set_rss+0xb79/0xe40 bnxt_hwrm_vnic_rss_cfg_p5+0xf7/0x460 __bnxt_setup_vnic_p5+0x12e/0x270 __bnxt_open_nic+0x2262/0x2f30 bnxt_open_nic+0x5d/0xf0 ethnl_set_channels+0x5d4/0xb30 ethnl_default_set_doit+0x2f1/0x620 Reported-by: Breno Leitao <leitao@debian.org> Closes: https://lore.kernel.org/netdev/ZrC6jpghA3PWVWSB@gmail.com/ Fixes: 98ba1d931f61 ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Tested-by: Breno Leitao <leitao@debian.org> Link: https://patch.msgid.link/20240806053742.140304-1-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07igc: Fix qbv tx latency by setting gtxoffsetFaizal Rahim1-1/+1
A large tx latency issue was discovered during testing when only QBV was enabled. The issue occurs because gtxoffset was not set when QBV is active, it was only set when launch time is active. The patch "igc: Correct the launchtime offset" only sets gtxoffset when the launchtime_enable field is set by the user. Enabling launchtime_enable ultimately sets the register IGC_TXQCTL_QUEUE_MODE_LAUNCHT (referred to as LaunchT in the SW user manual). Section 7.5.2.6 of the IGC i225/6 SW User Manual Rev 1.2.4 states: "The latency between transmission scheduling (launch time) and the time the packet is transmitted to the network is listed in Table 7-61." However, the patch misinterprets the phrase "launch time" in that section by assuming it specifically refers to the LaunchT register, whereas it actually denotes the generic term for when a packet is released from the internal buffer to the MAC transmit logic. This launch time, as per that section, also implicitly refers to the QBV gate open time, where a packet waits in the buffer for the QBV gate to open. Therefore, latency applies whenever QBV is in use. TSN features such as QBU and QAV reuse QBV, making the latency universal to TSN features. Discussed with i226 HW owner (Shalev, Avi) and we were in agreement that the term "launch time" used in Section 7.5.2.6 is not clear and can be easily misinterpreted. Avi will update this section to: "When TQAVCTRL.TRANSMIT_MODE = TSN, the latency between transmission scheduling and the time the packet is transmitted to the network is listed in Table 7-61." Fix this issue by using igc_tsn_is_tx_mode_in_tsn() as a condition to write to gtxoffset, aligning with the newly updated SW User Manual. Tested: 1. Enrol taprio on talker board base-time 0 cycle-time 1000000 flags 0x2 index 0 cmd S gatemask 0x1 interval1 index 0 cmd S gatemask 0x1 interval2 Note: interval1 = interval for a 64 bytes packet to go through interval2 = cycle-time - interval1 2. Take tcpdump on listener board 3. Use udp tai app on talker to send packets to listener 4. Check the timestamp on listener via wireshark Test Result: 100 Mbps: 113 ~193 ns 1000 Mbps: 52 ~ 84 ns 2500 Mbps: 95 ~ 223 ns Note that the test result is similar to the patch "igc: Correct the launchtime offset". Fixes: 790835fcc0cb ("igc: Correct the launchtime offset") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix reset adapter logics when tx mode changeFaizal Rahim1-5/+19
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes, remaining issues with the reset adapter logic in igc_tsn_offload_apply() have been observed: 1. The reset adapter logics for i225 and i226 differ, although they should be the same according to the guidelines in I225/6 HW Design Section 7.5.2.1 on software initialization during tx mode changes. 2. The i225 resets adapter every time, even though tx mode doesn't change. This occurs solely based on the condition igc_is_device_id_i225() when calling schedule_work(). 3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only resets adapter for legacy->tsn tx mode transitions. 4. qbv_count introduced in the patch is actually not needed; in this context, a non-zero value of qbv_count is used to indicate if tx mode was unconditionally set to tsn in igc_tsn_enable_offload(). This could be replaced by checking the existing register IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit. This patch resolves all issues and enters schedule_work() to reset the adapter only when changing tx mode. It also removes reliance on qbv_count. qbv_count field will be removed in a future patch. Test ran: 1. Verify reset adapter behaviour in i225/6: a) Enrol a new GCL Reset adapter observed (tx mode change legacy->tsn) b) Enrol a new GCL without deleting qdisc No reset adapter observed (tx mode remain tsn->tsn) c) Delete qdisc Reset adapter observed (tx mode change tsn->legacy) 2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed" to confirm it remains resolved. Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix qbv_config_change_errors logicsFaizal Rahim3-10/+15
When user issues these cmds: 1. Either a) or b) a) mqprio with hardware offload disabled b) taprio with txtime-assist feature enabled 2. etf 3. tc qdisc delete 4. taprio with base time in the past At step 4, qbv_config_change_errors wrongly increased by 1. Excerpt from IEEE 802.1Q-2018 8.6.9.3.1: "If AdminBaseTime specifies a time in the past, and the current schedule is running, then: Increment ConfigChangeError counter" qbv_config_change_errors should only increase if base time is in the past and no taprio is active. In user perspective, taprio was not active when first triggered at step 4. However, i225/6 reuses qbv for etf, so qbv is enabled with a dummy schedule at step 2 where it enters igc_tsn_enable_offload() and qbv_count got incremented to 1. At step 4, it enters igc_tsn_enable_offload() again, qbv_count is incremented to 2. Because taprio is running, tc_setup_type is TC_SETUP_QDISC_ETF and qbv_count > 1, qbv_config_change_errors value got incremented. This issue happens due to reliance on qbv_count field where a non-zero value indicates that taprio is running. But qbv_count increases regardless if taprio is triggered by user or by other tsn feature. It does not align with qbv_config_change_errors expectation where it is only concerned with taprio triggered by user. Fixing this by relocating the qbv_config_change_errors logic to igc_save_qbv_schedule(), eliminating reliance on qbv_count and its inaccuracies from i225/6's multiple uses of qbv feature for other TSN features. The new function created: igc_tsn_is_taprio_activated_by_user() uses taprio_offload_enable field to indicate that the current running taprio was triggered by user, instead of triggered by non-qbv feature like etf. Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07igc: Fix packet still tx after gate close by reducing i226 MAC retry bufferFaizal Rahim2-0/+40
Testing uncovered that even when the taprio gate is closed, some packets still transmit. According to i225/6 hardware errata [1], traffic might overflow the planned QBV window. This happens because MAC maintains an internal buffer, primarily for supporting half duplex retries. Therefore, even when the gate closes, residual MAC data in the buffer may still transmit. To mitigate this for i226, reduce the MAC's internal buffer from 192 bytes to the recommended 88 bytes by modifying the RETX_CTL register value. This follows guidelines from: [1] Ethernet Controller I225/I22 Spec Update Rev 2.1 Errata Item 9: TSN: Packet Transmission Might Cross Qbv Window [2] I225/6 SW User Manual Rev 1.2.4: Section 8.11.5 Retry Buffer Control Note that the RETX_CTL register can't be used in TSN mode because half duplex feature cannot coexist with TSN. Test Steps: 1. Send taprio cmd to board A: tc qdisc replace dev enp1s0 parent root handle 100 taprio \ num_tc 4 \ map 3 2 1 0 3 3 3 3 3 3 3 3 3 3 3 3 \ queues 1@0 1@1 1@2 1@3 \ base-time 0 \ sched-entry S 0x07 500000 \ sched-entry S 0x0f 500000 \ flags 0x2 \ txtime-delay 0 Note that for TC3, gate should open for 500us and close for another 500us. 3. Take tcpdump log on Board B. 4. Send udp packets via UDP tai app from Board A to Board B. 5. Analyze tcpdump log via wireshark log on Board B. Ensure that the total time from the first to the last packet received during one cycle for TC3 does not exceed 500us. Fixes: 43546211738e ("igc: Add new device ID's") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Fix incorrect assigns of FEC countsMateusz Polchlopek1-4/+4
Commit ac21add2540e ("ice: Implement driver functionality to dump fec statistics") introduces obtaining FEC correctable and uncorrectable stats per netdev in ICE driver. Unfortunately the assignment of values to fec_stats structure has been done incorrectly. This commit fixes the assignments. Fixes: ac21add2540e ("ice: Implement driver functionality to dump fec statistics") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Skip PTP HW writes during PTP reset procedureGrzegorz Nitka1-0/+4
Block HW write access for the driver while the device is in reset to avoid potential race condition and access to the PTP HW in non-nominal state which could lead to undesired effects Fixes: 4aad5335969f ("ice: add individual interrupt allocation") Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-07ice: Fix reset handlerGrzegorz Nitka1-0/+2
Synchronize OICR IRQ when preparing for reset to avoid potential race conditions between the reset procedure and OICR Fixes: 4aad5335969f ("ice: add individual interrupt allocation") Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-08-03gve: Fix use of netif_carrier_ok()Praveen Kaligineedi2-7/+7
GVE driver wrongly relies on netif_carrier_ok() to check the interface administrative state when resources are being allocated/deallocated for queue(s). netif_carrier_ok() needs to be replaced with netif_running() for all such cases. Administrative state is the result of "ip link set dev <dev> up/down". It reflects whether the administrator wants to use the device for traffic and the corresponding resources have been allocated. Fixes: 5f08cd3d6423 ("gve: Alloc before freeing when adjusting queues") Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com> Reviewed-by: Shailend Chand <shailend@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20240801205619.987396-1-pkaligineedi@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01Merge tag 'net-6.11-rc2' of ↵Linus Torvalds22-132/+201
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Paolo Abeni: "Including fixes from wireless, bleutooth, BPF and netfilter. Current release - regressions: - core: drop bad gso csum_start and offset in virtio_net_hdr - wifi: mt76: fix null pointer access in mt792x_mac_link_bss_remove - eth: tun: add missing bpf_net_ctx_clear() in do_xdp_generic() - phy: aquantia: only poll GLOBAL_CFG regs on aqr113, aqr113c and aqr115c Current release - new code bugs: - smc: prevent UAF in inet_create() - bluetooth: btmtk: fix kernel crash when entering btmtk_usb_suspend - eth: bnxt: reject unsupported hash functions Previous releases - regressions: - sched: act_ct: take care of padding in struct zones_ht_key - netfilter: fix null-ptr-deref in iptable_nat_table_init(). - tcp: adjust clamping window for applications specifying SO_RCVBUF Previous releases - always broken: - ethtool: rss: small fixes to spec and GET - mptcp: - fix signal endpoint re-add - pm: fix backup support in signal endpoints - wifi: ath12k: fix soft lockup on suspend - eth: bnxt_en: fix RSS logic in __bnxt_reserve_rings() - eth: ice: fix AF_XDP ZC timeout and concurrency issues - eth: mlx5: - fix missing lock on sync reset reload - fix error handling in irq_pool_request_irq" * tag 'net-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits) mptcp: fix duplicate data handling mptcp: fix bad RCVPRUNED mib accounting ipv6: fix ndisc_is_useropt() handling for PIO igc: Fix double reset adapter triggered from a single taprio cmd net: MAINTAINERS: Demote Qualcomm IPA to "maintained" net: wan: fsl_qmc_hdlc: Discard received CRC net: wan: fsl_qmc_hdlc: Convert carrier_lock spinlock to a mutex net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys net/mlx5e: Fix CT entry update leaks of modify header context net/mlx5e: Require mlx5 tc classifier action support for IPsec prio capability net/mlx5: Fix missing lock on sync reset reload net/mlx5: Lag, don't use the hardcoded value of the first port net/mlx5: DR, Fix 'stack guard page was hit' error in dr_rule net/mlx5: Fix error handling in irq_pool_request_irq net/mlx5: Always drain health in shutdown callback net: Add skbuff.h to MAINTAINERS r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY netfilter: iptables: Fix potential null-ptr-deref in ip6table_nat_table_init(). netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init(). net: drop bad gso csum_start and offset in virtio_net_hdr ...
2024-08-01igc: Fix double reset adapter triggered from a single taprio cmdFaizal Rahim1-16/+17
Following the implementation of "igc: Add TransmissionOverrun counter" patch, when a taprio command is triggered by user, igc processes two commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both commands unconditionally pass through igc_tsn_offload_apply() which evaluates and triggers reset adapter. The double reset causes issues in the calculation of adapter->qbv_count in igc. TAPRIO_CMD_REPLACE command is expected to reset the adapter since it activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same because it doesn't configure any driver-specific TSN settings. So, the evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS. To address this, commands parsing are relocated to igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter reset will exit after processing, thus avoiding igc_tsn_offload_apply(). Fixes: d3750076d464 ("igc: Add TransmissionOverrun counter") Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptysShahar Shitrit1-1/+6
Since the documentation for mlx5_toggle_port_link states that it should only be used after setting the port register, we add a check for the return value from mlx5_port_set_eth_ptys to ensure the register was successfully set before calling it. Fixes: 667daedaecd1 ("net/mlx5e: Toggle link only after modifying port parameters") Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com> Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5e: Fix CT entry update leaks of modify header contextChris Mi1-0/+1
The cited commit allocates a new modify header to replace the old one when updating CT entry. But if failed to allocate a new one, eg. exceed the max number firmware can support, modify header will be an error pointer that will trigger a panic when deallocating it. And the old modify header point is copied to old attr. When the old attr is freed, the old modify header is lost. Fix it by restoring the old attr to attr when failed to allocate a new modify header context. So when the CT entry is freed, the right modify header context will be freed. And the panic of accessing error pointer is also fixed. Fixes: 94ceffb48eac ("net/mlx5e: Implement CT entry update") Signed-off-by: Chris Mi <cmi@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-8-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5e: Require mlx5 tc classifier action support for IPsec prio capabilityRahul Rameshbabu1-3/+4
Require mlx5 classifier action support when creating IPSec chains in offload path. MLX5_IPSEC_CAP_PRIO should only be set if CONFIG_MLX5_CLS_ACT is enabled. If CONFIG_MLX5_CLS_ACT=n and MLX5_IPSEC_CAP_PRIO is set, configuring IPsec offload will fail due to the mlxx5 ipsec chain rules failing to be created due to lack of classifier action support. Fixes: fa5aa2f89073 ("net/mlx5e: Use chains for IPsec policy priority offload") Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-7-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5: Fix missing lock on sync reset reloadMoshe Shemesh1-1/+4
On sync reset reload work, when remote host updates devlink on reload actions performed on that host, it misses taking devlink lock before calling devlink_remote_reload_actions_performed() which results in triggering lock assert like the following: WARNING: CPU: 4 PID: 1164 at net/devlink/core.c:261 devl_assert_locked+0x3e/0x50 … CPU: 4 PID: 1164 Comm: kworker/u96:6 Tainted: G S W 6.10.0-rc2+ #116 Hardware name: Supermicro SYS-2028TP-DECTR/X10DRT-PT, BIOS 2.0 12/18/2015 Workqueue: mlx5_fw_reset_events mlx5_sync_reset_reload_work [mlx5_core] RIP: 0010:devl_assert_locked+0x3e/0x50 … Call Trace: <TASK> ? __warn+0xa4/0x210 ? devl_assert_locked+0x3e/0x50 ? report_bug+0x160/0x280 ? handle_bug+0x3f/0x80 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? devl_assert_locked+0x3e/0x50 devlink_notify+0x88/0x2b0 ? mlx5_attach_device+0x20c/0x230 [mlx5_core] ? __pfx_devlink_notify+0x10/0x10 ? process_one_work+0x4b6/0xbb0 process_one_work+0x4b6/0xbb0 […] Fixes: 84a433a40d0e ("net/mlx5: Lock mlx5 devlink reload callbacks") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-6-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5: Lag, don't use the hardcoded value of the first portMark Bloch1-1/+1
The cited commit didn't change the body of the loop as it should. It shouldn't be using MLX5_LAG_P1. Fixes: 7e978e7714d6 ("net/mlx5: Lag, use actual number of lag ports") Signed-off-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5: DR, Fix 'stack guard page was hit' error in dr_ruleYevgeny Kliteynik1-1/+1
This patch reduces the size of hw_ste_arr_optimized array that is allocated on stack from 640 bytes (5 match STEs + 5 action STES) to 448 bytes (2 match STEs + 5 action STES). This fixes the 'stack guard page was hit' issue, while still fitting majority of the usecases (up to 2 match STEs). Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by: Alex Vesker <valex@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-4-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5: Fix error handling in irq_pool_request_irqShay Drory1-3/+7
In case mlx5_irq_alloc fails, the previously allocated index remains in the XArray, which could lead to inconsistencies. Fix it by adding error handling that erases the allocated index from the XArray if mlx5_irq_alloc returns an error. Fixes: c36326d38d93 ("net/mlx5: Round-Robin EQs over IRQs") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Maher Sanalla <msanalla@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-3-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01net/mlx5: Always drain health in shutdown callbackShay Drory2-1/+2
There is no point in recovery during device shutdown. if health work started need to wait for it to avoid races and NULL pointer access. Hence, drain health WQ on shutdown callback. Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver") Fixes: d2aa060d40fa ("net/mlx5: Cancel health poll before sending panic teardown command") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-2-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-01r8169: don't increment tx_dropped in case of NETDEV_TX_BUSYHeiner Kallweit1-6/+2
The skb isn't consumed in case of NETDEV_TX_BUSY, therefore don't increment the tx_dropped counter. Fixes: 188f4af04618 ("r8169: use NETDEV_TX_{BUSY/OK}") Cc: stable@vger.kernel.org Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/bbba9c48-8bac-4932-9aa1-d2ed63bc9433@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-31Merge branch '100GbE' of ↵Jakub Kicinski6-90/+135
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== ice: fix AF_XDP ZC timeout and concurrency issues Maciej Fijalkowski says: Changes included in this patchset address an issue that customer has been facing when AF_XDP ZC Tx sockets were used in combination with flow control and regular Tx traffic. After executing: ethtool --set-priv-flags $dev link-down-on-close on ethtool -A $dev rx on tx on launching multiple ZC Tx sockets on $dev + pinging remote interface (so that regular Tx traffic is present) and then going through down/up of $dev, Tx timeout occurred and then most of the time ice driver was unable to recover from that state. These patches combined together solve the described above issue on customer side. Main focus here is to forbid producing Tx descriptors when either carrier is not yet initialized or process of bringing interface down has already started. v1: https://lore.kernel.org/netdev/20240708221416.625850-1-anthony.l.nguyen@intel.com/ * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: xsk: fix txq interrupt mapping ice: add missing WRITE_ONCE when clearing ice_rx_ring::xdp_prog ice: improve updating ice_{t,r}x_ring::xsk_pool ice: toggle netif_carrier when setting up XSK pool ice: modify error handling when setting XSK pool in ndo_bpf ice: replace synchronize_rcu with synchronize_net ice: don't busy wait for Rx queue disable in ice_qp_dis() ice: respect netif readiness in AF_XDP ZC related ndo's ==================== Link: https://patch.msgid.link/20240729200716.681496-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-30net: mvpp2: Don't re-use loop iteratorDan Carpenter1-3/+3
This function has a nested loop. The problem is that both the inside and outside loop use the same variable as an iterator. I found this via static analysis so I'm not sure the impact. It could be that it loops forever or, more likely, the loop exits early. Fixes: 3a616b92a9d1 ("net: mvpp2: Add TX flow control support for jumbo frames") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/eaa8f403-7779-4d81-973d-a9ecddc0bf6f@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-29ice: xsk: fix txq interrupt mappingMaciej Fijalkowski1-10/+14
ice_cfg_txq_interrupt() internally handles XDP Tx ring. Do not use ice_for_each_tx_ring() in ice_qvec_cfg_msix() as this causing us to treat XDP ring that belongs to queue vector as Tx ring and therefore misconfiguring the interrupts. Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-02 12:08:32 +0300