| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
During probe and device reset, the ice driver reads some data from the
NVM image as part of ice_init_nvm. Part of this data includes a section
of the Option ROM which contains version information.
The function ice_get_orom_civd_data is used to locate the '$CIV' data
section of the Option ROM.
Timing of ice_probe and ice_rebuild indicate that the
ice_get_orom_civd_data function takes about 10 seconds to finish
executing.
The function locates the section by scanning the Option ROM every 512
bytes. This requires a significant number of NVM read accesses, since
the Option ROM bank is 500KB. In the worst case it would take about 1000
reads. Worse, all PFs serialize this operation during reload because of
acquiring the NVM semaphore.
The CIVD section is located at the end of the Option ROM image data.
Unfortunately, the driver has no easy method to determine the offset
manually. Practical experiments have shown that the data could be at
a variety of locations, so simply reversing the scanning order is not
sufficient to reduce the overall read time.
Instead, copy the entire contents of the Option ROM into memory. This
allows reading the data using 4Kb pages instead of 512 bytes at a time.
This reduces the total number of firmware commands by a factor of 8. In
addition, reading the whole section together at once allows better
indication to firmware of when we're "done".
Re-write ice_get_orom_civd_data to allocate virtual memory to store the
Option ROM data. Copy the entire OptionROM contents at once using
ice_read_flash_module. Finally, use this memory copy to scan for the
'$CIV' section.
This change significantly reduces the time to read the Option ROM CIVD
section from ~10 seconds down to ~1 second. This has a significant
impact on the total time to complete a driver rebuild or probe.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_devlink_flash_update function performs a few upfront checks and
then calls ice_flash_pldm_image.
Most if these checks make more sense in the context of code within
ice_flash_pldm_image. Merge ice_devlink_flash_update and
ice_flash_pldm_image into one function, placing it in ice_fw_update.c
Since this is still the entry point for devlink, call the function
ice_devlink_flash_update instead of ice_flash_pldm_image. This leaves a
single function which handles the devlink parameters and then initiates
a PLDM update.
With this change, the ice_devlink_flash_update function in
ice_fw_update.c becomes the main entry point for flash update. It
elimintes some unnecessary boiler plate code between the two previous
functions. The ultimate motivation for this is that it eases supporting
a dry run with the PLDM library in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_devlink_flash_update function performs a few checks and then
calls ice_flash_pldm_image. One of these checks is to call
ice_check_for_pending_update. This function checks if the device has
a pending update, and cancels it if so. This is necessary to allow
a new flash update to proceed.
We want to refactor the ice code to eliminate ice_devlink_flash_update,
moving its checks into ice_flash_pldm_image.
To do this, ice_check_for_pending_update will become static, and only
called by ice_flash_pldm_image. To make this change easier to review,
first just move the function up within the ice_fw_update.c file.
While at it, note that the function has a misleading name. Its primary
action is to cancel a pending update. Using the verb "check" does not
imply this. Rename it to ice_cancel_pending_update.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove the unused define ICE_FLOW_SEG_HDRS_L2_MASK.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
The "bitmap" variable is already an unsigned long so there is no need
for this cast.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.
With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
- ICE_DDP_PKG_SUCCESS
- ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
- ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.
One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).
We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.
Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since the capability of a PTYPE within a specific package could be
negotiated by checking the HW bit map, it means that there's no need
to maintain a different PTYPE list for each type of the package when
parsing PTYPE. So refactor the PTYPE validating mechanism.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Scan the 'Marker Ptype TCAM' section to retrieve the Rx parser PTYPE
enable information from the current package.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
zero_copy_allocator has been removed back when Bjorn Topel introduced
xsk_buff_pool. Remove references to it that were dangling in the tree.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20211210171511.11574-1-maciej.fijalkowski@intel.com
|
|
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
|
|
The watchdog task incorrectly changes the state to __IAVF_RESETTING,
instead of letting the reset task take care of that. This was already
resolved by commit 22c8fd71d3a5 ("iavf: do not override the adapter
state in the watchdog task") but the problem was reintroduced by the
recent code refactoring in commit 45eebd62999d ("iavf: Refactor iavf
state machine tracking").
Fixes: 45eebd62999d ("iavf: Refactor iavf state machine tracking")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This code was re-organized and there some unlocks missing now.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver uses irq_set_affinity_hint() to update the affinity_hint mask
that is consumed by the userspace to distribute the interrupts. However,
under the hood irq_set_affinity_hint() also applies the provided cpumask
(if not NULL) as the affinity for the given interrupt which is an
undocumented side effect.
To remove this side effect irq_set_affinity_hint() has been marked
as deprecated and new interfaces have been introduced. Hence, replace the
irq_set_affinity_hint() with the new interface irq_update_affinity_hint()
that only updates the affinity_hint pointer.
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210903152430.244937-10-nitesh@redhat.com
|
|
The driver uses irq_set_affinity_hint() for two purposes:
- To set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- To apply an affinity that it provides for the i40e interrupts
The latter is done to ensure that all the interrupts are evenly spread
across all available CPUs. However, since commit a0c9259dc4e1 ("irq/matrix:
Spread interrupts on allocation") the spreading of interrupts is
dynamically performed at the time of allocation. Hence, there is no need
for the drivers to enforce their own affinity for the spreading of
interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
pointer for the affinity_hint.
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210903152430.244937-4-nitesh@redhat.com
|
|
The driver uses irq_set_affinity_hint() for two purposes:
- To set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- To apply an affinity that it provides for the iavf interrupts
The latter is done to ensure that all the interrupts are evenly spread
across all available CPUs. However, since commit a0c9259dc4e1 ("irq/matrix:
Spread interrupts on allocation") the spreading of interrupts is
dynamically performed at the time of allocation. Hence, there is no need
for the drivers to enforce their own affinity for the spreading of
interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
pointer for the affinity_hint.
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210903152430.244937-3-nitesh@redhat.com
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-08
Yahui adds re-initialization of Flow Director for VF reset.
Paul restores interrupts when enabling VFs.
Dave re-adds bandwidth check for DCBNL and moves DSCP mode check
earlier in the function.
Jesse prevents reporting of dropped packets that occur during
initialization and fixes reporting of statistics which could occur with
frequent reads.
Michal corrects setting of protocol type for UDP header and fixes lack
of differentiation when adding filters for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: safer stats processing
ice: fix adding different tunnels
ice: fix choosing UDP header type
ice: ignore dropped packets during init
ice: Fix problems with DSCP QoS implementation
ice: rearm other interrupt cause register after enabling VFs
ice: fix FDIR init missing when reset VF
====================
Link: https://lore.kernel.org/r/20211208211144.2629867-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da546 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Adding filters with the same values inside for VXLAN and Geneve causes HW
error, because it looks exactly the same. To choose between different
type of tunnels new recipe is needed. Add storing tunnel types in
creating recipes function and start checking it in finding function.
Change getting open tunnels function to return port on correct tunnel
type. This is needed to copy correct port to dummy packet.
Block user from adding enc_dst_port via tc flower, because VXLAN and
Geneve filters can be created only with destination port which was
previously opened.
Fixes: 8b032a55c1bd5 ("ice: low level support for tunnels")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In tunnels packet there can be two UDP headers:
- outer which for hw should be mark as ICE_UDP_OF
- inner which for hw should be mark as ICE_UDP_ILOS or as ICE_TCP_IL if
inner header is of TCP type
In none tunnels packet header can be:
- UDP, which for hw should be mark as ICE_UDP_ILOS
- TCP, which for hw should be mark as ICE_TCP_IL
Change incorrect ICE_UDP_OF for none tunnel packets to ICE_UDP_ILOS.
ICE_UDP_OF is incorrect for none tunnel packets and setting it leads to
error from hw while adding this kind of recipe.
In summary, for tunnel outer port type should always be set to
ICE_UDP_OF, for none tunnel outer and tunnel inner it should always be
set to ICE_UDP_ILOS.
Fixes: 9e300987d4a8 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59deb0 ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The patch that implemented DSCP QoS implementation removed a
bandwidth check that was used to check for a specific condition
caused by some corner cases. This check should not of been
removed.
The same patch also added a check for when the DCBx state could
be changed in relation to DSCP, but the check was erroneously
added nested in a check for CEE mode, which made the check useless.
Fix these problems by re-adding the bandwidth check and relocating
the DSCP mode check earlier in the function that changes DCBx state
in the driver.
Fixes: 2a87bd73e50d ("ice: Add DSCP support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The other interrupt cause register (OICR), global interrupt 0, is
disabled when enabling VFs to prevent handling VFLR. If the OICR is
not rearmed then the VF cannot communicate with the PF.
Rearm the OICR after enabling VFs.
Fixes: 916c7fdf5e93 ("ice: Separate VF VSI initialization/creation from reset flow")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When VF is being reset, ice_reset_vf() will be called and FDIR
resource should be released and initialized again.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
Fixes: 02e9c290814c ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc280473 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef253 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f5e ("i40evf: main driver core")
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-11-30
This series contains updates to iavf driver only.
Patryk adds a debug message when MTU is changed.
Grzegorz adds messaging when transitioning in and out of multicast
promiscuous mode.
Jake returns correct error codes for iavf_parse_cls_flower().
Jedrzej adds messaging for when the driver is removed and refactors
struct usage to take less memory. He also adjusts ethtool statistics to
only display information on active queues.
Tony allows for user to specify the RSS hash.
Karen resolves some static analysis warnings, corrects format specifiers,
and rewords a message to come across as informational.
v2:
- Dropped patch 1 (for net) and 5
- Change MTU message from info to debug
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-11-30
This series contains updates to ice driver only.
Shiraz corrects assignment of boolean variable and removes an unused
enum.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver provided too many lines as an output to ethtool -S command.
Return actual length of string set of ethtool stats. Instead of predefined
maximal value use the actual value on netdev, iterate over active queues.
Without this patch, ethtool -S report would produce additional
erroneous lines of queues that are not configured.
Signed-off-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change format to match variable type that is used in string.
Use %u format for unsigned variable and %d format for signed variable
to remove static analysis warnings.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This message is intended to be informational to indicate a reset is about
to happen, but the use of "warning" in the message text can cause concern
with users. Reword the message to make it less alarming.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change min() to min_t() to fix static code analysis warning of possible
overflow.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
iavf_mac_filter struct contained couple boolean
flags using up more memory than is necessary.
Change the flags to be bitfields in an anonymous struct
so all the flags now fit in one byte.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Driver support for changing the RSS hash key exists, however, checks
have caused it to be reported as unsupported. Remove the check and
allow the hash key to be specified.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
|
|
Add kernel trace that device was removed.
Currently there is no such information.
I.e. Host admin removes a PCI device from a VM,
than on VM shall be info about the event.
This patch adds info log to iavf_remove function.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
