| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-26
This series contains updates to i40e and i40evf.
Michal updates the driver to pass critical errors from the firmware to
the caller.
Patryk fixes an issue of creating multiple identical filters with the
same location, by simply moving the functions so that we remove the
existing filter and then add the new filter.
Paweł adds back in the ability to turn off offloads when VLAN is set for
the VF driver. Fixed an issue where the number of TC queue pairs was
exceeding MSI-X vectors count, causing messages about invalid TC mapping
and wrong selected Tx queue.
Alex cleans up the i40e/i40evf_set_itr_per_queue() by dropping all the
unneeded pointer chases. Puts to use the reg_idx value, which was going
unused, so that we can avoid having to compute the vector every time
throughout the driver.
Upasana enable the driver to display LLDP information on the vSphere Web
Client by exposing DCB parameters.
Alice converts our flags from 32 to 64 bit size, since we have added
more flags.
Dave implements a private ethtool flag to disable the processing of LLDP
packets by the firmware, so that the firmware will not consume LLDPDU
and cause them to be sent up the stack.
Alan adds a mechanism for detecting/storing the flag for processing of
LLDP packets by the firmware, so that its current state is persistent
across reboots/reloads of the driver.
Avinash fixes kdump with i40e due to resource constraints. We were
enabling VMDq and iWARP when we just have a single CPU, which was
starving kdump for the lack of IRQs.
Jake adds support to program the fragmented IPv4 input set PCTYPE.
Fixed the reported masks to properly report that the entire field is
masked, since we had accidentally swapped the mask values for the IPv4
addresses with the L4 port numbers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 36777d9fa24c ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa24c ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Our hardware does not allow situations where two filters might conflict
when matching. Essentially hardware only programs one filter for each
set of matching criteria. We don't support filters with overlapping
input sets, because each flow type can only use a single input set.
Additionally, different flow types will never have overlapping matches,
because of how the hardware parses the flow type before checking
matching criteria.
For this reason, we do not need or use the location number when
programming filters to hardware.
In order to avoid confusing scenarios with filters that match the same
criteria but program the flow to different queues, do not allow multiple
filters that match identical criteria to be programmed.
This ensures that we avoid odd scenarios when deleting filters, and when
programming new filters that match the same criteria.
Instead, users that wish to update the criteria for a filter must use
the same location id, or must delete all the matching filters first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clean up unnecessary parenthesis.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As we have added more flags, we need to now use more
bits and have over flooded the 32 bit size. So
make it 64.
Also change all the existing bits to unsigned long long
bits.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables driver to display LLDP information on the vSphere Web
Client with Intel adapters (X710, XL710) and Distributed Virtual Switch.
Signed-off-by: Upasana Menon <upasana.menon@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds back the capability to turn off offloads when VF has
VLAN set. The commit 0a3b4f702fb1 ("i40evf: enable support for VF VLAN
tag stripping control") adds the i40evf_set_features function and
changes the 'turn off' flow for offloads. This patch adds that
capability back by moving checking the VLAN option for VF to the
next statement.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit 2de6aa3a666e ("ixgbe: Add support for padding packet")
Uses RXDCTL.RLPML to limit the maximum frame size on Rx when using
build_skb. Unfortunately that register does not work on 82599.
Added an explicit check to avoid setting this register on 82599 MAC.
Extended the comment related to the setting of RXDCTL.RLPML to better
explain its purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
"offset" can't be both 0x0 and 0xFFFF so presumably || was intended
instead of &&. That matches with how this check is done in other
functions.
Fixes: 73834aec7199 ("ixgbe: extend firmware version support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since 5G link speed is supported by some devices, add reporting of 5G link
speed.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current code enables on X550 timestamping of all packets for any
filter, which means ethtool should not report any PTP-specific filters
as unsupported.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the ARRAY_SIZE macro on array buf to determine size of the array.
Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the ARRAY_SIZE macro on various arrays to determine
size of the arrays. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit ec718254cbfe
("ixgbe: Improve performance and reduce size of ixgbe_tx_map")
This change is meant to both improve the performance and reduce the size of
ixgbevf_tx_map().
Expand the work done in the main loop by pushing first into tx_buffer.
This allows us to pull in the dma_mapping_error check, the tx_buffer value
assignment, and the initial DMA value assignment to the Tx descriptor.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit d2bead576e67
("igb: Clear Rx buffer_info in configure instead of clean")
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We already had placehloders for failed page and buffer allocations.
Added alloc_rx_page and made sure the stats are properly updated and
exposed in ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit bd4171a5d4c2
("igb: update code to better handle incrementing page count")
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit 5be5955425c2
("igb: update driver to make use of DMA_ATTR_SKIP_CPU_SYNC")
and
commit 7bd175928280 ("igb: Add support for DMA_ATTR_WEAK_ORDERING")
Convert the calls to dma_map/unmap_page() to the attributes version
and add DMA_ATTR_SKIP_CPU_SYNC/WEAK_ORDERING which should help
improve performance on some platforms.
Move sync_for_cpu call before we perform a prefetch to avoid
invalidating the first 128 bytes of the packet on architectures where
that call may invalidate the cache.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on:
commit 7ec0116c9131 ("igb: Use length to determine if descriptor is done")
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition we only reset the Rx descriptor length for descriptor zero when
resetting a ring instead of having to do a memset with 0 over the entire
ring. By doing this we can save some time on initialization.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on commit 64f2525ca4e7 ("igb: Only DMA sync frame length")
On some architectures synching a buffer for DMA may be expensive.
Instead of the entire 2K receive buffer only synchronize the length of
the frame, which will typically be the MTU or smaller.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Introduce ixgbevf_can_reuse_page() similar to the change in ixgbe from
commit af43da0dba0b
("ixgbe: Add function for checking to see if we can reuse page")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-01-24
This series contains updates to fm10k only.
Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.
Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.
Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device. This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.
This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.
This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.
However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.
Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.
This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.
Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.
Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().
This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768b7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.
To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.
In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb_enable_sriov()
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon
hotplugging my kernel would immediately crash due to igb:
[ 680.825801] kernel BUG at drivers/pci/msi.c:352!
[ 680.828388] invalid opcode: 0000 [#1] SMP
[ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb]
[ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6
[ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017
[ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn
[ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0
[ 680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286
[ 680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c
[ 680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178
[ 680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00
[ 680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298
[ 680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000
[ 680.836332] FS: 0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000
[ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0
[ 680.837954] Call Trace:
[ 680.838853] pci_disable_msix+0xce/0xf0
[ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb]
[ 680.840278] igb_remove+0x9d/0x110 [igb]
[ 680.840764] pci_device_remove+0x36/0xb0
[ 680.841279] device_release_driver_internal+0x157/0x220
[ 680.841739] pci_stop_bus_device+0x7d/0xa0
[ 680.842255] pci_stop_bus_device+0x2b/0xa0
[ 680.842722] pci_stop_bus_device+0x3d/0xa0
[ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20
[ 680.843627] trim_stale_devices+0xf3/0x140
[ 680.844086] trim_stale_devices+0x94/0x140
[ 680.844532] trim_stale_devices+0xa6/0x140
[ 680.845031] ? get_slot_status+0x90/0xc0
[ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140
[ 680.846021] acpiphp_hotplug_notify+0x175/0x200
[ 680.846581] ? free_bridge+0x100/0x100
[ 680.847113] acpi_device_hotplug+0x8a/0x490
[ 680.847535] acpi_hotplug_work_fn+0x1a/0x30
[ 680.848076] process_one_work+0x182/0x3a0
[ 680.848543] worker_thread+0x2e/0x380
[ 680.848963] ? process_one_work+0x3a0/0x3a0
[ 680.849373] kthread+0x111/0x130
[ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50
[ 680.850188] ret_from_fork+0x1f/0x30
[ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b
[ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0
As it turns out, normally the freeing of IRQs that would fix this is called
inside of the scope of __igb_close(). However, since the device is
already gone by the point we try to unregister the netdevice from the
driver due to a hotplug we end up seeing that the netif isn't present
and thus, forget to free any of the device IRQs.
So: make sure that if we're in the process of dismantling the netdev, we
always allow __igb_close() to be called so that IRQs may be freed
normally. Additionally, only allow igb_close() to be called from
__igb_close() if it hasn't already been called for the given adapter.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 9474933caf21 ("igb: close/suspend race in netif_device_detach")
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable@vger.kernel.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
