| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 4aea7a5c5e940c1723add439f4088844cd26196d upstream.
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19110cfbb34d4af0cdfe14cd243f3b09dc95b013 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3509f8bc7b0560044c15f0e3ecfde1d9af757a6 upstream.
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4c40e51f9c32c6dd8adf606624c930a1c4d9bbb upstream.
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b8edcc685b5e2c3c37aa13dc50a88e84a5bfef8 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f72271e2a0ae4277d53c4053f5eed8bb346ba38a upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae0c585d93dfaf923d2c7eb44b2c3ab92854ea9b upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e1f9ca546556e508d021545861f6b5fc75a95fe upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4cb99185b4cc96c0a1c70104dc21ae14d7e7f28 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52c6912fde0133981ee50ba08808f257829c4c93 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch updates the i40e driver to include programming descriptors in
the cleaned_count. Without this change it becomes possible for us to leak
memory as we don't trigger a large enough allocation when the time comes to
allocate new buffers and we end up overwriting a number of rx_buffers equal
to the number of programming descriptors we encountered.
Fixes: 0e626ff7ccbf ("i40e: Fix support for flow director programming status")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It looks like there was either a copy/paste error or just a typo that
resulted in the Tx ITR setting being used to determine if we were using
adaptive Rx interrupt moderation or not.
This patch fixes the typo.
Fixes: 65e87c0398f5 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is a partial revert of "ixgbe: Don't bother clearing buffer
memory for descriptor rings". Specifically I messed up the exception
handling path a bit and this resulted in us incorrectly adding the count
back in when we didn't need to.
In order to make this simpler I am reverting most of the exception handling
path change and instead just replacing the bit that was handled by the
unmap_and_free call.
Fixes: ffed21bcee7a ("ixgbe: Don't bother clearing buffer memory for descriptor rings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the driver cannot map a TX buffer, instead of rolling back
gracefully and retrying later, we currently get a panic:
[ 159.885994] igb 0000:00:00.0: TX DMA map failed
[ 159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8
...
[ 159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8
Fix the erroneous test that leads to this situation.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if the stat type is invalid then data[i] is being set
either by dereferencing a null pointer p, or it is reading from
an incorrect previous location if we had a valid stat type
previously. Fix this by skipping over the read of p on an invalid
stat type.
Detected by CoverityScan, CID#113385 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a race condition that can result into the interface being
up and carrier on, but with transmits disabled in the hardware.
The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which
allows e1000_watchdog() interleave with e1000_down().
CPU x CPU y
--------------------------------------------------------------------
e1000_down():
netif_carrier_off()
e1000_watchdog():
if (carrier == off) {
netif_carrier_on();
enable_hw_transmit();
}
disable_hw_transmit();
e1000_watchdog():
/* carrier on, do nothing */
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7ccbf ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d94 ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f0883 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc5b ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff69 ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e443e ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The dynamic ITR algorithm depends on a calculation of usecs which
assumes that the interrupts have been firing constantly at the interrupt
throttle rate. This is not guaranteed because we could have a low packet
rate, or have been polling in software.
We'll estimate whether this is the case by using jiffies to determine if
we've been too long. If the time difference of jiffies is larger we are
guaranteed to have an incorrect calculation. If the time difference of
jiffies is smaller we might have been polling some but the difference
shouldn't affect the calculation too much.
This ensures that we don't get stuck in BULK latency during certain rare
situations where we receive bursts of packets that force us into NAPI
polling.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit c56625d59726 ("i40e/i40evf: change dynamic interrupt
thresholds") a new higher latency ITR setting called I40E_ULTRA_LATENCY
was added with a cryptic comment about how it was meant for adjusting Rx
more aggressively when streaming small packets.
This mode was attempting to calculate packets per second and then kick
in when we have a huge number of small packets.
Unfortunately, the ULTRA setting was kicking in for workloads it wasn't
intended for including single-thread UDP_STREAM workloads.
This wasn't caught for a variety of reasons. First, the ip_defrag
routines were improved somewhat which makes the UDP_STREAM test still
reasonable at 10GbE, even when dropped down to 8k interrupts a second.
Additionally, some other obvious workloads appear to work fine, such
as TCP_STREAM.
The number 40k doesn't make sense for a number of reasons. First, we
absolutely can do more than 40k packets per second. Second, we calculate
the value inline in an integer, which sometimes can overflow resulting
in using incorrect values.
If we fix this overflow it makes it even more likely that we'll enter
ULTRA mode which is the opposite of what we want.
The ULTRA mode was added originally as a way to reduce CPU utilization
during a small packet workload where we weren't keeping up anyways. It
should never have been kicking in during these other workloads.
Given the issues outlined above, let's remove the ULTRA latency mode. If
necessary, a better solution to the CPU utilization issue for small
packet workloads will be added in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 96db776a3682 ("i40e/vf: fix interrupt affinity bug")
we added some code to force exit of polling in case we did
not have the correct CPU. This is important since it was possible for
the IRQ affinity to be changed while the CPU is pegged at 100%. This can
result in the polling routine being stuck on the wrong CPU until
traffic finally stops.
Unfortunately, the implementation, "if the CPU is correct, exit as
normal, otherwise, fall-through to the end-polling exit" is incredibly
confusing to reason about. In this case, the normal flow looks like the
exception, while the exception actually occurs far away from the if
statement and comment.
We recently discovered and fixed a bug in this code because we were
incorrectly initializing the affinity mask.
Re-write the code so that the exceptional case is handled at the check,
rather than having the logic be spread through the regular exit flow.
This does end up with minor code duplication, but the resulting code is
much easier to reason about.
The new logic is identical, but inverted. If we are running on a CPU not
in our affinity mask, we'll exit polling. However, the code flow is much
easier to understand.
Note that we don't actually have to check for MSI-X, because in the MSI
case we'll only have one q_vector, but its default affinity mask should
be correct as it includes all CPUs when it's initialized. Further, we
could at some point add code to setup the notifier for the non-MSI-X
case and enable this workaround for that case too, if desired, though
there isn't much gain since its unlikely to be the common case.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On older kernels a call to irq_set_affinity_hint does not guarantee that
the IRQ affinity will be set. If nothing else on the system sets the IRQ
affinity this can result in a bug in the i40e_napi_poll() routine where
we notice that our interrupt fired on the "wrong" CPU according to our
internal affinity_mask variable.
This results in a bug where we continuously tell NAPI to stop polling to
move the interrupt to a new CPU, but the CPU never changes because our
affinity mask does not match the actual mask setup for the IRQ.
The root problem is a mismatched affinity mask value. So lets initialize
the value to cpu_possible_mask instead. This ensures that prior to the
first time we get an IRQ affinity notification we'll have the mask set
to include every possible CPU.
We use cpu_possible_mask instead of cpu_online_mask since the former is
almost certainly never going to change, while the later might change
after we've made a copy.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we don't have MSI-X enabled, we handle interrupts on all icr0. This
is a special case, so let's move the conditional into
i40e_update_enable_itr() in order to make i40e_napi_poll easier to
read about.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit 3ffa037d7f78 ("i40e: Set XPS bit mask to zero in DCB mode")
we've tried to reset the XPS settings by building a custom
empty CPU mask.
This workaround is not necessary because we're not really removing the
XPS setting, but simply setting it so that no CPU is valid.
Second, we shorten the code further by using zalloc_cpumask_var instead
of a separate call to bitmap_zero().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes an issue where an error return value is
set, but without an immediate exit, the value can be overwritten
by the following code execution. The condition at this point
is not fatal, so remove the error assignment and comment the
intent for future code maintainers
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch improves the system log message. The log message will
be expanded to include the FEC mode the FW requested before link
was established.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch gives VF capability to control VLAN tag stripping via
ethtool. As rx-vlan-offload was fixed before, now the VF is able to
change it using "ethtool --offload <IF> rxvlan on/off" settings.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In new versions of GCC since 7.x a new warning exists which warns when
a string is truncated before all of the format can be completed.
When we setup VMDQ netdev names we are copying a pre-existing interface
name which could be up to 15 characters in length. Since we also add
4 bytes, v, the literal %, the d and a \0 null, we would overrun the
available size unless snprintf truncated for us.
The snprintf call will of course truncate on the end, so lets instead
modify the code to force truncation of the copied netdev name by
4 characters, to create enough space for the 4 bytes we're adding.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The q_vector names are based on the interface name with a driver prefix,
the type of q_vector setup, and the queue number. We previously set the
size of this variable to IFNAMSIZ + 9, which is incorrect, because we
actually include a minimum of 14 characters extra beyond the interface
name size.
New versions of GCC since 7 include a new warning that detects this
possible truncation and complains. We can fix this by increasing the
size in case our interface name is too large to avoid truncation. We
don't need to go beyond 14 because the compiler is smart enough to
realize our values can never exceed size of 1. We do go up to 15 here
because possible future changes may increase the number of queues beyond
one digit.
While we are here, also change some variables to be unsigned (since they
are never negative) and stop using an extra unnecessary %s format
specifier.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Albeit, we usually set true promiscuous mode for both multicast and
unicast at the same time - however, it is possible to set it
individually, so using allmulti flag which is only for allmulticast might
caused unwanted behavior in mirroring egress traffic promiscuous for
unicast in VF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Increase the size of the prefix buffer so that it can hold enough
characters for every possible input. Although 20 is enough for all
expected inputs, it is possible for the values to be larger than
expected, resulting in a possibly truncated string. Additionally, lets
use sizeof(prefix) in order to ensure we use the correct size if we need
to change the array length in the future.
New versions of GCC starting at 7 now include warnings to prevent
truncation unless you handle the return code. At most 27 bytes can be
written here, so lets just increase the buffer size even if for all
expected hw->bus.* values we only needed 20.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store information about FEC modes, that were requested. It will be used
in printing link status information function and this way there is no
need to call admin queue there.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.
This fix updates the state variables so that adminq_subtask will have
accurate information whenever it gets scheduled.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.
This issue existed before but surfaced after commit 373149fc99a0
("i40e: Decrease the scope of rtnl lock")
This fix adds locking around admin queue command and update of
state variables so that adminq_subtask will have accurate information
whenever it gets scheduled.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the driver allows the user to change (or even disable)
interrupt moderation if adaptive-rx/tx is enabled when this should
not be the case.
Adaptive RX/TX will not respect the user's ITR settings so
allowing the user to change it is weird. This bug would also
allow the user to disable interrupt moderation with adaptive-rx/tx
enabled which doesn't make much sense either.
This patch makes it such that if adaptive-rx/tx is enabled, the user
cannot make any manual adjustments to interrupt moderation. It also
makes it so that if ITR is disabled but adaptive-rx/tx is then
enabled, ITR will be re-enabled.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the header file cpumask.h, we shouldn't be directly copying
a cpumask_t, since its a bitmap and might not be copied correctly. Lets
use the provided cpumask_copy() function instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we're going to bother initializing a variable to reference it we might
as well use it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
virtchnl_vf_resource
The current name of vf_offload_flags indicates that the bitmap is
limited to offload related features. Make this more generic by renaming
it to vf_cap_flags, which allows for other capabilities besides
offloading to be added.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In i40e_vsi_add_vlan we treat attempting to add VID=0 as an error,
because it does not do what the caller might expect. We already special
case VID=0 in i40e_vlan_rx_add_vid so that we avoid this error when
adding the VLAN.
This special casing is necessary so that we do not add the VLAN=0 filter
since we don't want to stop receiving untagged traffic. Unfortunately,
not all callers of i40e_vsi_add_vlan are aware of this, including when
we add VLANs from a VF device.
Rather than special casing every single caller of i40e_vsi_add_vlan,
lets just move this check internally. This makes the code simpler
because the caller does not need to be aware of how VLAN=0 is special,
and we don't forget to add this check in new places.
This fixes a harmless error message displaying when adding a VLAN from
within a VF. The message was meaningless but there is no reason to
confuse end users and system administrators, and this is now avoided.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
