| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Bump the version number reflect the corresponding functionality in the
out of tree driver.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We reset during the shutdown path which will reset AUTOC register. This
would change LMS to 10G. If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work. For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were only turning the laser on when the adapter was up. This
causes issues for those who wanted to access the MNG FW while the
port was in a down state. This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch modifies the driver to enable certain devices, which have an internal
switch, to read data from the physical slot rather than reading data from the
internal switch. The internal switch will always report the same PCI width and
speed, which is not useful compared to knowing the width and speed of the slot
the physical card is plugged into.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch cleans up ixgbe_get_bus_info_generic to call some conversion
functions, which are used also in a follow on patch that needs to convert
between the link_status PCIe config values into ixgbe's internal enum
representations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset. As a result we were not pulling in TCP headers when the DNF
flag was set.
To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
e100 uses pci_map_single, but fails to check for a dma mapping error after its
use, resulting in a stack trace:
[ 46.656594] ------------[ cut here ]------------
[ 46.657004] WARNING: at lib/dma-debug.c:933 check_unmap+0x47b/0x950()
[ 46.657004] Hardware name: To Be Filled By O.E.M.
[ 46.657004] e100 0000:00:0e.0: DMA-API: device driver failed to check map
error[device address=0x000000007a4540fa] [size=90 bytes] [mapped as single]
[ 46.657004] Modules linked in:
[ 46.657004] w83627hf hwmon_vid snd_via82xx ppdev snd_ac97_codec ac97_bus
snd_seq snd_pcm snd_mpu401 snd_mpu401_uart ns558 snd_rawmidi gameport parport_pc
e100 snd_seq_device parport snd_page_alloc snd_timer snd soundcore skge shpchp
k8temp mii edac_core i2c_viapro edac_mce_amd nfsd auth_rpcgss nfs_acl lockd
sunrpc binfmt_misc uinput ata_generic pata_acpi radeon i2c_algo_bit
drm_kms_helper ttm firewire_ohci drm firewire_core pata_via sata_via i2c_core
sata_promise crc_itu_t
[ 46.657004] Pid: 792, comm: ip Not tainted 3.8.0-0.rc6.git0.1.fc19.x86_64 #1
[ 46.657004] Call Trace:
[ 46.657004] <IRQ> [<ffffffff81065ed0>] warn_slowpath_common+0x70/0xa0
[ 46.657004] [<ffffffff81065f4c>] warn_slowpath_fmt+0x4c/0x50
[ 46.657004] [<ffffffff81364cfb>] check_unmap+0x47b/0x950
[ 46.657004] [<ffffffff8136522f>] debug_dma_unmap_page+0x5f/0x70
[ 46.657004] [<ffffffffa030f0f0>] ? e100_tx_clean+0x30/0x210 [e100]
[ 46.657004] [<ffffffffa030f1a8>] e100_tx_clean+0xe8/0x210 [e100]
[ 46.657004] [<ffffffffa030fc6f>] e100_poll+0x56f/0x6c0 [e100]
[ 46.657004] [<ffffffff8159dce1>] ? net_rx_action+0xa1/0x370
[ 46.657004] [<ffffffff8159ddb2>] net_rx_action+0x172/0x370
[ 46.657004] [<ffffffff810703bf>] __do_softirq+0xef/0x3d0
[ 46.657004] [<ffffffff816e4ebc>] call_softirq+0x1c/0x30
[ 46.657004] [<ffffffff8101c485>] do_softirq+0x85/0xc0
[ 46.657004] [<ffffffff81070885>] irq_exit+0xd5/0xe0
[ 46.657004] [<ffffffff816e5756>] do_IRQ+0x56/0xc0
[ 46.657004] [<ffffffff816dacb2>] common_interrupt+0x72/0x72
[ 46.657004] <EOI> [<ffffffff816da1eb>] ?
_raw_spin_unlock_irqrestore+0x3b/0x70
[ 46.657004] [<ffffffff816d124d>] __slab_free+0x58/0x38b
[ 46.657004] [<ffffffff81214424>] ? fsnotify_clear_marks_by_inode+0x34/0x120
[ 46.657004] [<ffffffff811b0417>] ? kmem_cache_free+0x97/0x320
[ 46.657004] [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
[ 46.657004] [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
[ 46.657004] [<ffffffff811b0692>] kmem_cache_free+0x312/0x320
[ 46.657004] [<ffffffff8157fc14>] sock_destroy_inode+0x34/0x40
[ 46.657004] [<ffffffff811e8c28>] destroy_inode+0x38/0x60
[ 46.657004] [<ffffffff811e8d5e>] evict+0x10e/0x1a0
[ 46.657004] [<ffffffff811e9605>] iput+0xf5/0x180
[ 46.657004] [<ffffffff811e4338>] dput+0x248/0x310
[ 46.657004] [<ffffffff811ce0e1>] __fput+0x171/0x240
[ 46.657004] [<ffffffff811ce26e>] ____fput+0xe/0x10
[ 46.657004] [<ffffffff8108d54c>] task_work_run+0xac/0xe0
[ 46.657004] [<ffffffff8106c6ed>] do_exit+0x26d/0xc30
[ 46.657004] [<ffffffff8109eccc>] ? finish_task_switch+0x7c/0x120
[ 46.657004] [<ffffffff816dad58>] ? retint_swapgs+0x13/0x1b
[ 46.657004] [<ffffffff8106d139>] do_group_exit+0x49/0xc0
[ 46.657004] [<ffffffff8106d1c4>] sys_exit_group+0x14/0x20
[ 46.657004] [<ffffffff816e3b19>] system_call_fastpath+0x16/0x1b
[ 46.657004] ---[ end trace 4468c44e2156e7d1 ]---
[ 46.657004] Mapped at:
[ 46.657004] [<ffffffff813663d1>] debug_dma_map_page+0x91/0x140
[ 46.657004] [<ffffffffa030e8eb>] e100_xmit_prepare+0x12b/0x1c0 [e100]
[ 46.657004] [<ffffffffa030c924>] e100_exec_cb+0x84/0x140 [e100]
[ 46.657004] [<ffffffffa030e56a>] e100_xmit_frame+0x3a/0x190 [e100]
[ 46.657004] [<ffffffff8159ee89>] dev_hard_start_xmit+0x259/0x6c0
Easy fix, modify the cb paramter to e100_exec_cb to return an error, and do the
dma_mapping_error check in the obvious place
This was reported previously here:
http://article.gmane.org/gmane.linux.network/257893
But nobody stepped up and fixed it.
CC: Josh Boyer <jwboyer@redhat.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Michal Jaegermann <michal@harddata.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the administrator has not assigned a MAC address to the VF via the
PF then handle it gracefully by generating a temporary MAC address.
This ensures that we always know when we have a random address and
udev won't get upset about it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The previous commit ce43a2168c59bc47b5f0c1825fd5f9a2a9e3b447 (e1000e:
cleanup USLEEP_RANGE checkpatch checks) converted a number of delays and
sleeps as recommended in ./Documentation/timers/timers-howto.txt.
Unfortunately, a few of the udelay() to usleep_range() conversions are in
code paths that are in an atomic context in which usleep_range() should
not be used. Revert those specific changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like"
GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed
when link is up (which must not exceed the maximum latency supported
by the platform), otherwise specify there is no LTR requirement.
Unlike true-PCIe devices which set the LTR maximum snoop/no-snoop
latencies in the LTR Extended Capability Structure in the PCIe Extended
Capability register set, on this device LTR is set by writing the
equivalent snoop/no-snoop latencies in the LTRV register in the MAC and
set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB)
message to the PMC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that IEEE802.3az-2010 Energy Efficient Ethernet has been approved as
standard (September 2010) and the driver can enable and disable it via
ethtool, enable the feature by default on parts which support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled. In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one. In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the MAC and PHY are in two different modes (different power levels
and interconnect speeds), it could take a long time before a PHY register
access timed out using the existing MAC-PHY interconnect configuration
coded into the driver for ICH- and PCH-based LOMs. Introduce an I217/I218-
specific .setup_physical_interface operation which does not override the
interconnect configuration in the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the LEDs are driven by cathode, the bit logic is reversed. Use the
LED Invert bit to invert the logic. Cleanup use of a magic number and
change the for loop increment to reduce the number of shifts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low
performance. This is because 82579 is excessively aggressive on transmit
at 10Mb half-duplex and will not provide sufficient time for the link
partner to transmit. When the link partner is also 82579, the result is a
lot of collisions (and corresponding re-transmits) that cause the poor
performance. To work-around this issue, significantly increase the IPG in
the MAC to allow enough gap for the link partner to transmit and reduce the
Rx latency in the analog PHY to 0 to reduce the number of collisions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PHY reads/writes via the MDIC register could potentially return results
from a previous PHY register access. If that happens, the offset in the
returned results will be that of the previous access and if that is
different from the expected offset, log a debug message and error out.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After dma_map_page, dma_mapping_error must be called. It seems safe to
not free the skb/page allocated in this function, as the skb/page can be
reused later.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After dma_map_single, dma_mapping_error must be called. It seems safe to
not free the skb allocated in this function, as the skb can be reused
later.
Additionally this patch fixes one coding-style error.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After dma_map_single, dma_mapping_error must be called.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For 82576 MAC type, max_adj is reported as 1000000000 ppb. However, if
this value is passed to igb_ptp_adjfreq_82576, incvalue overflows out of
INCVALUE_82576_MASK, resulting in setting of zero TIMINCA.incvalue, stopping
the PHC (instead of going at twice the nominal speed).
Fix the advertised max_adj value to the largest value hardware can handle.
As there is no min_adj value available (-max_adj is used instead), this will
also prevent stopping the clock intentionally. It's probably not a big deal,
other igb MAC types don't support stopping the clock, either.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Trivial sparse warning.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb is ineffective at setting a lower total VFs because:
int pci_sriov_set_totalvfs(struct pci_dev *dev, u16 numvfs)
{
...
/* Shouldn't change if VFs already enabled */
if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE)
return -EBUSY;
Swap init ordering.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The max_vfs= option has always been self limiting to the number of VFs
supported by the device. fa44f2f1 added SR-IOV configuration via
sysfs, but in the process broke this self correction factor. The
failing path is:
igb_probe
igb_sw_init
if (max_vfs > 7) {
adapter->vfs_allocated_count = 7;
...
igb_probe_vfs
igb_enable_sriov(, max_vfs)
if (num_vfs > 7) {
err = -EPERM;
...
This leaves vfs_allocated_count = 7 and vf_data = NULL, so we bomb out
when igb_probe finally calls igb_reset. It seems like a really bad
idea, and somewhat pointless, to set vfs_allocated_count separate from
vf_data, but limiting max_vfs is enough to avoid the null pointer.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a problem in i350 where anti spoofing configuration was written into a
wrong register.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the ixgbevf driver is opened the request to allocate MSIX irq
vectors may fail. In that case the driver will call ixgbevf_down()
which will call ixgbevf_irq_disable() to clear the HW interrupt
registers and calls synchronize_irq() using the msix_entries pointer in
the adapter structure. However, when the function to request the MSIX
irq vectors failed it had already freed the msix_entries which causes
an OOPs from using the NULL pointer in synchronize_irq().
The calls to pci_disable_msix() and to free the msix_entries memory
should not occur if device open fails. Instead they should be called
during device driver removal to balance with the call to
pci_enable_msix() and the call to allocate msix_entries memory
during the device probe and driver load.
Signed-off-by: Li Xun <xunleer.li@huawei.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Resolve strict checkpatch USLEEP_RANGE checks by converting delays and
sleeps as described in ./Documentation/timers/timers-howto.txt. Three
other violations of the text have also been fixed.
CHECK:USLEEP_RANGE: usleep_range is preferred over udelay; see
Documentation/timers/timers-howto.txt
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Cuddle broken lines where appropriate.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
CHECK:SPACING: No space is necessary after a cast
CHECK:SPACING: space prohibited before semicolon
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
WARNING:LEADING_SPACE: please, no spaces at the start of a line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
WARNING:LONG_LINE: line over 80 characters
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV)
ERROR:SPACING: need consistent spacing around '-' (ctx:WxV)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SPACING: spaces required around that '=' (ctx:VxV)
WARNING:SPACING: missing space after enum definition
and some similar spacing issues not reported by checkpatch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
