| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 0a9a17e3bb4564caf4bfe2a6783ae1287667d188 upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1fe954b2097bb907b4578e6a74e4c1d23785a601 ]
FEC is configured by the NVM and the driver should not be
overriding it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2bf1a87b903bd81b1448a1cef73de59fb6c4d340 ]
The indirection table was reported incorrectly for X550 and newer
where we can support up to 64 RSS queues.
Reported-by Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3f0d646b720d541309b11e190db58086f446f41e ]
A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f7f37e7ff2b9b7eff7fbd035569cab35896869a3 ]
When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();
Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 126db13fa0e6d05c9f94e0125f61e773bd5ab079 ]
Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5d6002b7b822c7423e75d4651e6790bfb5642b1b ]
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.
This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
- NONE only L2 exact match addresses or Flow Director enabled
- MULTI BAM and ROMPE set
- ALLMULTI BAM, ROMPE and MPE set
If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.
On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As per Eric Dumazet's previous patches:
(see commit (24d2e4a50737) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only call the internal_setup_link method when it is provided. This
check is required for newer version parts.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the reset never completes, it is necessary to retake the
semaphore before returning, because the caller will release
the semaphore.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch disables LRO by default in favor of GRO.
LRO is incompatible with forwarding and is disabled when forwarding
is turned on which makes the default offloads of the driver
inconsistent. LRO can still be enabled via ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch makes sure that flow control packets initiated by the VF are
dropped and reported as spoofed.
Flow control packets can be used to limit the throughput or as DOS
attack when generated from a VF. Flow control is not supported per VF
hence any pause frames generated from a VF are considered malicious.
Also cleaned up indentation and some redundant comments.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The 82599 and X540 datasheets require that FCRTH be "set" for Tx
switching (VM-to-VM loopback) but it did not previously specify what
the value should be set to. It has now been determined that
the correct value is RXPBSIZE - (24*1024).
This setting is also required for later devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add new device ID for X550EM device with SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Provide I2C combined operations on X550EM, not X550 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X550 has HW support for SCTP flow director filters SCTP mask. This
patch adds it like we do for UDP and TCP.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736cf ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
