summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/ixgbe
AgeCommit message (Collapse)AuthorFilesLines
2013-08-12ixgbe: Fix Tx Hang issue with lldpad on 82598EBJacob Keller1-2/+1
commit 1eb9ac14c34a948bf1538bfb9034e8ab29099a64 upstream. This patch fixes an issue with the 82598EB device, where lldpad is causing Tx Hangs on the card as soon as it attempts to configure DCB for the device. The adapter will continually Tx hang and reset in a loop. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-04-26ixgbe: add mac type to the version in ethtool_regsEmil Tantilov1-1/+2
This patch adds the mac type to the version in ethtool_regs. This will make it easier to check the mac type when dumping registers with ethtool. The drawback of this is that older versions of ethtool will only be able to dump in hex format for 82599 and above when used with the updated driver. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-26ixgbe: add support for disabling link at boot time on 82599Emil Tantilov2-2/+20
This patch adds support for disabling link during boot time. This feature was requested by customers and is configurable through the EEPROM. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-26ixgbe: cache AUTOC readsEmil Tantilov2-16/+25
This patch removes majority of the AUTOC register reads by using a cached value instead. The reason for this change is to avoid writing corrupted values to AUTOC due to bad FW. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-26ixgbe: fix register access during ethtool loopback testEmil Tantilov1-12/+14
This patch cleans up the logic in ixgbe_setup_loopback_test() to only access registers applicable to the MAC type. AUTOC is only valid on MACs older than X540. MACC is used for X540. In addition it removes a read of AUTOC and uses the stored value to force the link up. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-26ixgbe: fix EICR write in ixgbe_msix_otherJacob Keller1-0/+10
Previously, the ixgbe_msix_other was writing the full 32bits of the set interrupts, instead of only the ones which the ixgbe_msix_other is handling. This resulted in a loss of performance when the X540's PPS feature is enabled due to sometimes clearing queue interrupts which resulted in the driver not getting the interrupt for cleaning the q_vector rings often enough. The fix is to simply mask the lower 16bits off so that this handler does not write them in the EICR, which causes them to remain high and be properly handled by the clean_rings interrupt routine as normal. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: stable <stable@vger.kernel.org> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-25ixgbe: add WOL support for new subdevice IDEmil Tantilov2-0/+2
This patch adds a define and WOL support for a new subdevice ID. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-25ixgbe: add SFP+ LX module supportDon Skidmore4-10/+25
This patch adds LX support to 82599 devices. This is an alternate patch to the one suggested by Stefan Behte <s.behte@babiel.com> In addition this patch includes some cleanups such as: - removed parenthesis around "x == y ||" lines inside an if statement for consistency. - grouped the sx/lx sfp types along with srlr in ixgbe_get_settings() since they all have the same supported, advertised and port values. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reported-by: Stefan Behte <s.behte@babiel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-25ixgbe: rename wol_supported to more fitting wol_enabledJacob Keller3-4/+4
The variable wol_supported really is just checking whether it is enabled, rather than whether it is supported. If it is enabled it will be supported, but this does not necessarily hold true the other way around. This patch renames the variable to avoid confusion. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-25ixgbe: add driver support for x520 OCP adapter.Don Skidmore2-0/+9
This patch adds support for the new OCP x520 adapter. This support includes WoL. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-25ixgbe: fix possible divide by zero in ixgbe_update_itrDon Skidmore1-0/+3
Protect the code by bailing out of ixgbe_update_itr() when this occurs. The next call to ixgbe_update_itr will continue to dynamically update ITR. Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+6
Conflicts: drivers/net/ethernet/emulex/benet/be_main.c drivers/net/ethernet/intel/igb/igb_main.c drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c include/net/scm.h net/batman-adv/routing.c net/ipv4/tcp_input.c The e{uid,gid} --> {uid,gid} credentials fix conflicted with the cleanup in net-next to now pass cred structs around. The be2net driver had a bug fix in 'net' that overlapped with the VLAN interface changes by Patrick McHardy in net-next. An IGB conflict existed because in 'net' the build_skb() support was reverted, and in 'net-next' there was a comment style fix within that code. Several batman-adv conflicts were resolved by making sure that all calls to batadv_is_my_mac() are changed to have a new bat_priv first argument. Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO rewrite in 'net-next', mostly overlapping changes. Thanks to Stephen Rothwell and Antonio Quartulli for help with several of these merge resolutions. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19net: vlan: add protocol argument to packet tagging functionsPatrick McHardy1-1/+1
Add a protocol argument to the VLAN packet tagging functions. In case of HW tagging, we need that protocol available in the ndo_start_xmit functions, so it is stored in a new field in the skb. The new field fits into a hole (on 64 bit) and doesn't increase the sks's size. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19net: vlan: prepare for 802.1ad VLAN filtering offloadPatrick McHardy1-4/+6
Change the rx_{add,kill}_vid callbacks to take a protocol argument in preparation of 802.1ad support. The protocol argument used so far is always htons(ETH_P_8021Q). Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*Patrick McHardy2-7/+7
Rename the hardware VLAN acceleration features to include "CTAG" to indicate that they only support CTAGs. Follow up patches will introduce 802.1ad server provider tagging (STAGs) and require the distinction for hardware not supporting acclerating both. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19ixgbe: Remove unnecessary #ifdef CONFIG_DEBUG_FS testsJoe Perches2-10/+5
Add some empty static inlines instead to make the code more readable. Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-19ixgbe: Add support for WoL on 82599 SFP+ LOMJacob Keller2-0/+2
This patch adds software support for WoL for the 82599 SFP+ LOM device, (ID 0x8976) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-19ixgbe: in shutdown, do netif_running() under rtnl_lockakepner1-2/+2
During shutdown it's possible for __dev_close() (which holds rtnl_lock) to clear the __LINK_STATE_START bit, and for ixgbe to then read that bit (without holding rtnl_lock), and then not fail to free irqs, etc. The result is a crash like this: ------------[ cut here ]------------ kernel BUG at drivers/pci/msi.c:313! invalid opcode: 0000 [#1] SMP last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map CPU 1 Pid: 5910, comm: reboot Tainted: P ---------------- 2.6.32 #1 empty RIP: 0010:[<ffffffff81305c2b>] [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130 RSP: 0018:ffff880185c9bc88 EFLAGS: 00010282 RAX: ffff880219f58bc0 RBX: ffff88021ac53b00 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000246 RDI: 000000000000004a RBP: ffff880185c9bcc8 R08: 0000000000000002 R09: 0000000000000106 R10: 0000000000000000 R11: 0000000000000006 R12: ffff88021e524778 R13: 0000000000000001 R14: ffff88021e524000 R15: 0000000000000000 FS: 00007f90821b7700(0000) GS:ffff880028220000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f90818bd010 CR3: 0000000132c64000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process reboot (pid: 5910, threadinfo ffff880185c9a000, task ffff88021bf04a80) Stack: ffff880185c9bc98 000000018130529d ffff880185c9bcc8 ffff88021e524000 <0> 0000000000000004 ffff88021948c700 0000000000000000 ffff880185c9bda7 <0> ffff880185c9bce8 ffffffff81305cbd ffff880185c9bce8 ffff88021948c700 Call Trace: [<ffffffff81305cbd>] pci_disable_msix+0x3d/0x50 [<ffffffffa00501d5>] ixgbe_reset_interrupt_capability+0x65/0x90 [ixgbe] [<ffffffffa00512f6>] ixgbe_clear_interrupt_scheme+0xb6/0xd0 [ixgbe] [<ffffffffa005330b>] __ixgbe_shutdown+0x5b/0x200 [ixgbe] [<ffffffffa00534ca>] ixgbe_shutdown+0x1a/0x60 [ixgbe] [<ffffffff812f6c7c>] pci_device_shutdown+0x2c/0x50 [<ffffffff813727fb>] device_shutdown+0x4b/0x160 [<ffffffff8107d98c>] kernel_restart_prepare+0x2c/0x40 ehci timer_action, mod_timer io_watchdog [<ffffffff8107d9e6>] kernel_restart+0x16/0x60 [<ffffffff8107dbfd>] sys_reboot+0x1ad/0x200 [<ffffffff811676cf>] ? __d_free+0x3f/0x60 [<ffffffff81167748>] ? d_free+0x58/0x60 [<ffffffff8116f7c0>] ? mntput_no_expire+0x30/0x100 [<ffffffff81152b11>] ? __fput+0x191/0x200 [<ffffffff816565fe>] ? do_page_fault+0x3e/0xa0 [<ffffffff8100b132>] system_call_fastpath+0x16/0x1b Code: 4c 89 ef e8 98 8c e3 ff 4d 39 f4 48 8b 43 10 75 cf 48 83 c4 18 5b 41 5c 41 5d 41 5e 41 5f c9 c3 49 8b 7d 20 e8 07 5a d3 ff eb c9 <0f> 0b 0f 1f 00 eb fb 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 ehci timer_action, mod_timer io_watchdog RIP [<ffffffff81305c2b>] free_msi_irqs+0x11b/0x130 RSP <ffff880185c9bc88> ---[ end trace 27de882a0fe75593 ]--- (This was seen on a pretty old kernel/driver, but looks like the same bug is still possible.) Signed-off-by: <akepner@riverbed.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: Fix a bug in setting VF VLAN via PFGreg Rose1-0/+6
The PF driver does not check if the administrator has already set a VF VLAN via the PF driver before setting the new VLAN. This results in the following scenario: A) Administrator sets VF <n> to VLAN 100 B) Administrator sets VF <x> to VLAN 100 C) Administrator sets VF <n> to VLAN 200 D) The VF <n> driver continues to be able to receive traffic on VLAN 100 because the VLVFB pool enable bit for that VF was left set instead of being cleared as it should be. This fix ensures that the old VLAN filter for VF <n> is first removed and the pool bit enable for VF <n> is cleared so that it no longer receives traffic on VLAN 100. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-18ixgbe: bump version numberDon Skidmore1-1/+1
Bump the version number reflect the corresponding functionality in the out of tree driver. Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: Fix 1G link WoLDon Skidmore3-2/+8
We reset during the shutdown path which will reset AUTOC register. This would change LMS to 10G. If we were currently linked at 1G we will lose link, which is a bad thing if we wanted WoL to work. For the fix I needed to know if WoL is supported so I created a new bool in the ixgbe_hw struct. If this is set we will not allow the reset to change the current LMS value in AUTOC. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: fix MNG FW support when adapter not upDon Skidmore5-5/+65
We were only turning the laser on when the adapter was up. This causes issues for those who wanted to access the MNG FW while the port was in a down state. This patch makes sure the laser is turned on in probe and remain up even after the port is brought down. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: enable devices with internal switch to read pci parentJacob Keller1-0/+48
This patch modifies the driver to enable certain devices, which have an internal switch, to read data from the physical slot rather than reading data from the internal switch. The internal switch will always report the same PCI width and speed, which is not useful compared to knowing the width and speed of the slot the physical card is plugged into. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: create conversion functions from link_status to bus/speedJacob Keller2-32/+34
This patch cleans up ixgbe_get_bus_info_generic to call some conversion functions, which are used also in a follow on patch that needs to convert between the link_status PCIe config values into ixgbe's internal enum representations. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: Enable support for recognizing PCI-e Gen3 link speedJacob Keller3-1/+7
This patch adds support for displaying PCIe Gen3 link speed, which was previously missing from the driver. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: Drop check for PAGE_SIZE from ixgbe_xmit_frame_ringAlexander Duyck1-6/+1
The check for PAGE_SIZE is pointless now that the default configuration is to allocate 32K for all buffers. Since the Tx descriptor limit is 16K we can just drop the check and always compare the descriptors to the maximum size supported. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: don't do arithmetic operations on bitmasksEmil Tantilov1-1/+1
Make the calculation of eerd consistent between the read and write functions by using | instead of + for IXGBE_EEPROM_RW_REG_START Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-18ixgbe: Mask off check of frag_off as we only want fragment offsetAlexander Duyck1-1/+1
We were incorrectly checking the entire frag_off field when we only wanted the fragment offset. As a result we were not pulling in TCP headers when the DNF flag was set. To correct that we will now check for frag off using the IP_OFFSET mask. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-04-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-2/+9
Conflicts: drivers/nfc/microread/mei.c net/netfilter/nfnetlink_queue_core.c Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which some cleanups are going to go on-top. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-05ixgbe: fix registration order of driver and DCA nofiticationJakub Kicinski1-2/+9
ixgbe_notify_dca cannot be called before driver registration because it expects driver's klist_devices to be allocated and initialized. While on it make sure debugfs files are removed when registration fails. Cc: stable <stable@vger.kernel.org> Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-28ixgbe: Don't give VFs random MAC addressesGreg Rose1-10/+13
If the user has not assigned a MAC address to a VM, then don't give it a random one. Instead, just give it zeros and let it figure out what to do with them. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Stefan Assmann <sassmann@kpanic.de> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-03-08ixgbe: Make use of the default fdb handlers.Vlad Yasevich1-41/+1
For fdb_add, use the default handler in the non-SRIOV case. For the other fdb handlers, just remove them and use the default ones. CC: John Fastabend <john.r.fastabend@intel.com> Acked-By: John Fastabend <john.r.fastabend@intel.com> CC: CC: Gregory Rose <gregory.v.rose@intel.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-28hlist: drop the node parameter from iteratorsSasha Levin2-13/+13
I'm not sure why, but the hlist for each entry iterators were conceived list_for_each_entry(pos, head, member) The hlist ones were greedy and wanted an extra parameter: hlist_for_each_entry(tpos, pos, head, member) Why did they need an extra pos parameter? I'm not quite sure. Not only they don't really need it, it also prevents the iterator from looking exactly like the list iterator, which is unfortunate. Besides the semantic patch, there was some manual work required: - Fix up the actual hlist iterators in linux/list.h - Fix up the declaration of other iterators based on the hlist ones. - A very small amount of places were using the 'node' parameter, this was modified to use 'obj->member' instead. - Coccinelle didn't handle the hlist_for_each_entry_safe iterator properly, so those had to be fixed up manually. The semantic patch which is mostly the work of Peter Senna Tschudin is here: @@ iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host; type T; expression a,c,d,e; identifier b; statement S; @@ -T b; <+... when != b ( hlist_for_each_entry(a, - b, c, d) S | hlist_for_each_entry_continue(a, - b, c) S | hlist_for_each_entry_from(a, - b, c) S | hlist_for_each_entry_rcu(a, - b, c, d) S | hlist_for_each_entry_rcu_bh(a, - b, c, d) S | hlist_for_each_entry_continue_rcu_bh(a, - b, c) S | for_each_busy_worker(a, c, - b, d) S | ax25_uid_for_each(a, - b, c) S | ax25_for_each(a, - b, c) S | inet_bind_bucket_for_each(a, - b, c) S | sctp_for_each_hentry(a, - b, c) S | sk_for_each(a, - b, c) S | sk_for_each_rcu(a, - b, c) S | sk_for_each_from -(a, b) +(a) S + sk_for_each_from(a) S | sk_for_each_safe(a, - b, c, d) S | sk_for_each_bound(a, - b, c) S | hlist_for_each_entry_safe(a, - b, c, d, e) S | hlist_for_each_entry_continue_rcu(a, - b, c) S | nr_neigh_for_each(a, - b, c) S | nr_neigh_for_each_safe(a, - b, c, d) S | nr_node_for_each(a, - b, c) S | nr_node_for_each_safe(a, - b, c, d) S | - for_each_gfn_sp(a, c, d, b) S + for_each_gfn_sp(a, c, d) S | - for_each_gfn_indirect_valid_sp(a, c, d, b) S + for_each_gfn_indirect_valid_sp(a, c, d) S | for_each_host(a, - b, c) S | for_each_host_safe(a, - b, c, d) S | for_each_mesh_entry(a, - b, c, d) S ) ...+> [akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c] [akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c] [akpm@linux-foundation.org: checkpatch fixes] [akpm@linux-foundation.org: fix warnings] [akpm@linux-foudnation.org: redo intrusive kvm changes] Tested-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Gleb Natapov <gleb@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-16ixgbe: Update DESC_NEEDED define to adjust for changes to MAX_SKB_FRAGSAlexander Duyck1-1/+1
Recent changes have made it so that MAX_SKB_FRAGS is now never less than 16. As a result we were seeing issues on systems with 64K pages as it would cause DESC_NEEDED to increase to 68, and we would need over 136 descriptors free before clean_tx_irq would wake the queue. This patch makes it so that DESC_NEEDED is always MAX_SKB_FRAGS + 4. This should prevent any possible deadlocks on the systems with 64K pages as we will now only require 42 descriptors to wake. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: fix Tx timeouts with BQLEmil Tantilov2-7/+34
This patch makes sure that TXDCTL.WTHRESH is set to 1 when BQL is enabled and EITR is set to more than 100k interrupts per second to avoid Tx timeouts. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: implement SFF diagnostic monitoring via ethtoolAurélien Guillaume3-0/+119
This patch adds support for reading data from SFP+ modules over i2c. Signed-off-by: Aurélien Guillaume <footplus@gmail.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: cleanup error checking in ixgbe_identify_sfp_module_generic()Emil Tantilov1-24/+10
This patch replaces instances where a return code from i2c operations were checked against a list of error codes with a much simpler if ( status != 0 ) check. Some whitespace cleanups included. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: fix possible data corruption in read_i2c_byteEmil Tantilov1-1/+1
This patch makes sure that the SW lock is released after all i2c operations complete in the retry code path. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Add support for set_channels ethtool operationAlexander Duyck1-0/+38
This change adds support for the ethtool set_channels operation. Since the ixgbe driver has to support DCB as well as the other modes the assumption I made here is that the number of channels in DCB modes refers to the number of queues per traffic class, not the number of queues total. CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Add support for displaying the number of Tx/Rx channelsAlexander Duyck1-0/+72
This patch adds support for the ethtool get_channels operation. Since the ixgbe driver has to support DCB as well as the other modes the assumption I made here is that the number of channels in DCB modes refers to the number of queues per traffic class, not the number of queues total. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Make ixgbe_setup_tc usable even when DCB is not enabledAlexander Duyck2-13/+8
The ixgbe_setup_tc code is essentially the same code we need any time we have to update the number of queues. As such I am making it available always and just stripping the DCB specific bits out when DCB is disabled instead of stripping the entire function. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Update ixgbe driver to use __netdev_pick_tx in ixgbe_select_queueAlexander Duyck1-22/+26
This change updates the ixgbe driver to use __netdev_pick_tx instead of the current logic it is using to select a queue. The main result of this change is that ixgbe can now fully support XPS, and in the case of non-FCoE enabled configs it means we don't need to have our own ndo_select_queue. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Add function for setting XPS queue mappingAlexander Duyck3-5/+20
This change adds support for ixgbe to configure the XPS queue mapping on load. The result of this change is that on open we will now be resetting the number of Tx queues, and then setting the default configuration for XPS based on if ATR is enabled or disabled. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-16ixgbe: Define FCoE and Flow director limits much sooner to allow for changesAlexander Duyck3-35/+19
Instead of adjusting the FCoE and Flow director limits based on the number of CPUs we can define them much sooner. This allows the user to come through later and adjust them once we have updated the code to support the set_channels ethtool operation. I am still allowing for FCoE and RSS queues to be separated if the number queues is less than the number of CPUs. This essentially treats the two groupings like they are two separate traffic classes. In addition I am changing the initialization to use the MAX_TX/RX_QUEUES defines instead of trying to compute the value as it will be possible in upcoming patches for the user to request the maximum number of queues. I have also updated things so that the upper limit on queues is exactly 63 instead of allowing it to go up to 64. The reason for this change is to address the fact thqt the driver only supports up to 63 queue vectors since the hardware supports 64 MSI-X vectors, but one must be reserved for "other" causes. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-15ixgbe: refactor initialization of feature flagsEmil Tantilov1-20/+38
This patch reshuffles the switch/case structure of the flag assignment to allow for the flags to be set for each MAC type separately. This is needed for new HW that does not have feature parity with older HW. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by: Jack Morgan <jack.morgan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-02-14bridge: Add vlan support to static neighborsVlad Yasevich1-1/+1
When a user adds bridge neighbors, allow him to specify VLAN id. If the VLAN id is not specified, the neighbor will be added for VLANs currently in the ports filter list. If no VLANs are configured on the port, we use vlan 0 and only add 1 entry. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-14bridge: Dump vlan information from a bridge portVlad Yasevich1-1/+2
Using the RTM_GETLINK dump the vlan filter list of a given bridge port. The information depends on setting the filter flag similar to how nic VF info is dumped. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-0/+1
Conflicts: drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c The bnx2x gso_type setting bug fix in 'net' conflicted with changes in 'net-next' that broke the gso_* setting logic out into a seperate function, which also fixes the bug in question. Thus, use the 'net-next' version. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-13ixgbe: Only set gso_type to SKB_GSO_TCPV4 as RSC does not support IPv6Alexander Duyck1-6/+3
The original fix that was applied for setting gso_type required more change than necessary because it was assumed ixgbe does RSC on IPv6 frames and this is not correct. RSC is only supported with IPv4/TCP frames only. As such we can simplify the fix and avoid the unnecessary move of eth_type_trans. The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix to one line that sets gso_type to TCPV4 if the frame is RSC. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-11ixgbe: fix gso typeMichael S. Tsirkin1-2/+6
ixgbe set gso_size but not gso_type. This leads to crashes in macvtap. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-04 08:39:51 +0300