| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: Fabio Futigami <ffutigam@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
|
|
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
|
|
When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.
-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Cleanup code to make it more clean and readable.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
SYNCH bit and IV bit of RXCW register are sticky. Before examining these bits,
RXCW should be read twice to filter out one-time false events and have correct
values for these bits. Incorrect values of these bits in link check logic can
cause weird link stability issues if auto-negotiation fails.
CC: stable <stable@vger.kernel.org> [2.6.38+]
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: Ethan Zhao <ethan.kernel@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit 44abd5c12767a8c567dc4e45fd9aec3b13ca85e0 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.
This fix should be applied back through 3.4.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This define is needed by i217.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clear the REQ and GNT bit in the eeprom control register (EECD).
This is required if the eeprom is to be accessed with auto read
EERD register.
After a cold reset this doesn't matter but if PBIST MAC test was
executed before booting, the register was left in a dirty state
(the 2 bits where set), which caused the read operation to time out
and returning 0.
Reference (page 312):
http://download.intel.com/design/network/manuals/316080.pdf
Reported-by: Aleksandar Igic <aleksandar.igic@dektech.com.au>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Like other supported (igp) PHYs, the driver needs to be able to force the
master/slave mode on 82577. Since the code is the same as what already
exists in the code flow for igp PHYs, move it to a new function to be
called for both flows.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Version bump to 1.11.3-k.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For the 82573, ASPM L1 gets disabled wholesale so this special-case code
is not required. For the 82574 the previous patch does the same as for
the 82573, disabling L1 on the adapter. Thus, this code is no longer
required and can be removed.
Signed-off-by: Chris Boot <bootc@bootc.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ASPM on the 82574 causes trouble. Currently the driver disables L0s for
this NIC but only disables L1 if the MTU is >1500. This patch simply
causes L1 to be disabled regardless of the MTU setting.
Signed-off-by: Chris Boot <bootc@bootc.net>
Cc: "Wyborny, Carolyn" <carolyn.wyborny@intel.com>
Cc: Nix <nix@esperi.org.uk>
Link: https://lkml.org/lkml/2012/3/19/362
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For 82574 and 82583 devices, resolve an intermittent link issue where
the link negotiates to 100Mbps rather than 1Gbps when powering off the
PHY and powering on the PHY after several seconds.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling the locked versions of the read/write PHY ops function pointers
often produces excessively long lines. Shorten these as is done with
the non-locked versions of the PHY register read/write functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is a known issue in the 82577 and 82578 device that can cause a hang
in the device hardware during traffic stress; the current workaround in the
driver is to disable transmit flow control by default. If the user enables
transmit flow control and the device hang occurs, provide a message in the
syslog suggesting to re-enable the workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The PHY initialization flows and assorted workarounds for 82577/8/9 done
during driver load and resume from Sx should be the same yet they are not.
Combine the current flows/workarounds into a common set of functions that
are called during the different code paths.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
An update to the EEPROM on 82579 will extend a delay in hardware to fix an
issue with WoL not working after a G3->S5 transition which is unrelated to
the driver. However, this extended delay conflicts with nominal operation
of the device when it is initialized by the driver and after every reset
of the hardware (i.e. the driver starts configuring the device before the
hardware is done with it's own configuration work). The workaround for
when the driver is in control of the device is to tell the hardware after
every reset the configuration delay should be the original shorter one.
Some pre-existing variables are renamed generically to be re-used with
new register accesses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
|
|
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace occurrences of 'if (<bool expr> == <1|0>)' with
'if ([!]<bool expr>)'
Replace occurrences of '<bool var> = (<non-bool expr>) ? true : false'
with '<bool var> = <non-bool expr>'.
Replace occurrence of '<bool var> = <non-bool expr>' with
'<bool var> = !!<non-bool expr>'
While the latter replacement is not really necessary, it is done here for
consistency and clarity. No functional changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that split strings generate checkpatch warnings (per Chapter 2 of
Documentation/CodingStyle to make it easier to grep the code for the
string) cleanup the remaining instances of them in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some Rx and Tx specific registers are arrays indexed by the queue number.
For clarity, specify the intended queue rather than obscuring it behind a
define.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rename NAPI polling routine and a parameter with more appropriate names,
refactor a conditional branch to get rid of an unnecessary goto/label and
fix a line exceeding 80 columns.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Move the first phrase of a multi-line comment to the second line.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
