| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 52c4a1a85f4b346c39c896c0168f4a843b3385ff ]
As we know that AVB is enabled by default, and the ENET IP design is
queue 0 for best effort, queue 1&2 for AVB Class A&B. Bandwidth of each
queue 1&2 set in driver is 50%, TX bandwidth fluctuated when selecting
tx queues randomly with FEC_QUIRK_HAS_AVB quirk available.
This patch adds ndo_select_queue callback to select queues for
transmitting to fix this issue. It will always return queue 0 if this is
not a vlan packet, and return queue 1 or 2 based on priority of vlan
packet.
You may complain that in fact we only use single queue for trasmitting
if we are not targeted to VLAN. Yes, but seems we have no choice, since
AVB is enabled when the driver probed, we can't switch this feature
dynamicly. After compare multiple queues to single queue, TX throughput
almost no improvement.
One way we can implemet is to configure the driver to multiple queues
with Round-robin scheme by default. Then add ndo_setup_tc callback to
enable/disable AVB feature for users. Unfortunately, ENET AVB IP seems
not follow the standard 802.1Qav spec. We only can program
DMAnCFG[IDLE_SLOPE] field to calculate bandwidth fraction. And idle
slope is restricted to certain valus (a total of 19). It's far away from
CBS QDisc implemented in Linux TC framework. If you strongly suggest to do
this, I think we only can support limited numbers of bandwidth and reject
others, but it's really urgly and wried.
With this patch, VLAN tagged packets route to queue 0/1/2 based on vlan
priority; VLAN untagged packets route to queue 0.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 471ff4455d61c9929ae912328859921708e1eafc ]
Frieder Schrempf reported a TX throuthput issue [1], it happens quite often
that the measured bandwidth in TX direction drops from its expected/nominal
value to something like ~50% (for 100M) or ~67% (for 1G) connections.
[1] https://lore.kernel.org/linux-arm-kernel/421cc86c-b66f-b372-32f7-21e59f9a98bc@kontron.de/
The issue becomes clear after digging into it, Net core would select
queues when transmitting packets. Since FEC have not impletemented
ndo_select_queue callback yet, so it will call netdev_pick_tx to select
queues randomly.
For i.MX6SX ENET IP with AVB support, driver default enables this
feature. According to the setting of QOS/RCMRn/DMAnCFG registers, AVB
configured to Credit-based scheme, 50% bandwidth of each queue 1&2.
With below tests let me think more:
1) With FEC_QUIRK_HAS_AVB quirk, can reproduce TX bandwidth fluctuations issue.
2) Without FEC_QUIRK_HAS_AVB quirk, can't reproduce TX bandwidth fluctuations issue.
The related difference with or w/o FEC_QUIRK_HAS_AVB quirk is that, whether we
program FTYPE field of TxBD or not. As I describe above, AVB feature is
enabled by default. With FEC_QUIRK_HAS_AVB quirk, frames in queue 0
marked as non-AVB, and frames in queue 1&2 marked as AVB Class A&B. It's
unreasonable if frames in queue 1&2 are not required to be time-sensitive.
So when Net core select tx queues ramdomly, Credit-based scheme would work
and lead to TX bandwidth fluctuated. On the other hand, w/o
FEC_QUIRK_HAS_AVB quirk, frames in queue 1&2 are all marked as non-AVB, so
Credit-based scheme would not work.
Till now, how can we fix this TX throughput issue? Yes, please remove
FEC_QUIRK_HAS_AVB quirk if you suffer it from time-nonsensitive networking.
However, this quirk is used to indicate i.MX6SX, other setting depends
on it. So this patch adds a new quirk FEC_QUIRK_HAS_MULTI_QUEUES to
represent i.MX6SX, it is safe for us remove FEC_QUIRK_HAS_AVB quirk
now.
FEC_QUIRK_HAS_AVB quirk is set by default in the driver, and users may
not know much about driver details, they would waste effort to find the
root cause, that is not we want. The following patch is a implementation
to fix it and users don't need to modify the driver.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cb3cefe3f3f8af27c6076ef7d1f00350f502055d upstream.
Add clock rate zero check to fix coverity issue of "divide by 0".
Fixes: commit 85bd1798b24a ("net: fec: fix spin_lock dead lock")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d23765646e71b43ed2b809930411ba5c0aadee7b ]
Commit da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.
Fixes: da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 619fee9eb13b5d29e4267cb394645608088c28a8 ]
If the memory allocated for cbd_base is failed, it should
free the memory allocated for the queues, otherwise it causes
memory leak.
And if the memory allocated for the queues is failed, it can
return error directly.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 557d5dc83f6831b4e54d141e9b121850406f9a60 ]
Use the new mac_managed_pm flag to work around an issue with KSZ8081 PHY
that becomes unstable when a soft reset is triggered during aneg.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74c97ea3b61e4ce149444f904ee8d4fc7073505b ]
A link time bug that I had fixed before has come back now that
another sub-module was added to the enetc driver:
ERROR: modpost: "enetc_ierb_register_pf" [drivers/net/ethernet/freescale/enetc/fsl-enetc.ko] undefined!
The problem is that the enetc Makefile is not actually used for
the ierb module if that is the only built-in driver in there
and everything else is a loadable module.
Fix it by always entering the directory this time, regardless
of which symbols are configured. This should reliably fix the
problem and prevent it from coming back another time.
Fixes: 112463ddbe82 ("net: dsa: felix: fix link error")
Fixes: e7d48e5fbf30 ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Handle return error code of eth_mac_addr();
Fixes: 3d23a05c75c7 ("gianfar: Enable changing mac addr when if up")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The txtime is passed to the driver in skb->skb_mstamp_ns, which is
actually in a union with skb->tstamp (the place where software
timestamps are kept).
Since commit b50a5c70ffa4 ("net: allow simultaneous SW and HW transmit
timestamping"), __sock_recv_timestamp has some logic for making sure
that the two calls to skb_tstamp_tx:
skb_tx_timestamp(skb) # Software timestamp in the driver
-> skb_tstamp_tx(skb, NULL)
and
skb_tstamp_tx(skb, &shhwtstamps) # Hardware timestamp in the driver
will both do the right thing and in a race-free manner, meaning that
skb_tx_timestamp will deliver a cmsg with the software timestamp only,
and skb_tstamp_tx with a non-NULL hwtstamps argument will deliver a cmsg
with the hardware timestamp only.
Why are races even possible? Well, because although the software timestamp
skb->tstamp is private per skb, the hardware timestamp skb_hwtstamps(skb)
lives in skb_shinfo(skb), an area which is shared between skbs and their
clones. And skb_tstamp_tx works by cloning the packets when timestamping
them, therefore attempting to perform hardware timestamping on an skb's
clone will also change the hardware timestamp of the original skb. And
the original skb might have been yet again cloned for software
timestamping, at an earlier stage.
So the logic in __sock_recv_timestamp can't be as simple as saying
"does this skb have a hardware timestamp? if yes I'll send the hardware
timestamp to the socket, otherwise I'll send the software timestamp",
precisely because the hardware timestamp is shared.
Instead, it's quite the other way around: __sock_recv_timestamp says
"does this skb have a software timestamp? if yes, I'll send the software
timestamp, otherwise the hardware one". This works because the software
timestamp is not shared with clones.
But that means we have a problem when we attempt hardware timestamping
with skbs that don't have the skb->tstamp == 0. __sock_recv_timestamp
will say "oh, yeah, this must be some sort of odd clone" and will not
deliver the hardware timestamp to the socket. And this is exactly what
is happening when we have txtime enabled on the socket: as mentioned,
that is put in a union with skb->tstamp, so it is quite easy to mistake
it.
Do what other drivers do (intel igb/igc) and write zero to skb->tstamp
before taking the hardware timestamp. It's of no use to us now (we're
already on the TX confirmation path).
Fixes: 0d08c9ec7d6e ("enetc: add support time specific departure base on the qos etf")
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On LS1028A, the MAC RX FIFO defaults to the value 2, which is too high
and may lead to RX lock-up under traffic at a rate higher than 6 Gbps.
Set it to 1 instead, as recommended by the hardware design team and by
later versions of the ENETC block guide.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using jumbo packets and overrunning rx queue with napi enabled,
the following sequence is observed in gfar_add_rx_frag:
| lstatus | | skb |
t | lstatus, size, flags | first | len, data_len, *ptr |
---+--------------------------------------+-------+-----------------------+
13 | 18002348, 9032, INTERRUPT LAST | 0 | 9600, 8000, f554c12e |
12 | 10000640, 1600, INTERRUPT | 0 | 8000, 6400, f554c12e |
11 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, f554c12e |
10 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, f554c12e |
09 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, f554c12e |
08 | 14000640, 1600, INTERRUPT FIRST | 0 | 1600, 0, f554c12e |
07 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, f554c12e |
06 | 1c000080, 128, INTERRUPT LAST FIRST | 1 | 0, 0, abf3bd6e |
05 | 18002348, 9032, INTERRUPT LAST | 0 | 8000, 6400, c5a57780 |
04 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, c5a57780 |
03 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, c5a57780 |
02 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, c5a57780 |
01 | 10000640, 1600, INTERRUPT | 0 | 1600, 0, c5a57780 |
00 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, c5a57780 |
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This then crashes:
kernel BUG at include/linux/skbuff.h:2277!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c04689f4] skb_pull+0x2c/0x48
LR [c03f62ac] gfar_clean_rx_ring+0x2e4/0x844
Call Trace:
[ec4bfd38] [c06a84c4] _raw_spin_unlock_irqrestore+0x60/0x7c (unreliable)
[ec4bfda8] [c03f6a44] gfar_poll_rx_sq+0x48/0xe4
[ec4bfdc8] [c048d504] __napi_poll+0x54/0x26c
[ec4bfdf8] [c048d908] net_rx_action+0x138/0x2c0
[ec4bfe68] [c06a8f34] __do_softirq+0x3a4/0x4fc
[ec4bfed8] [c0040150] run_ksoftirqd+0x58/0x70
[ec4bfee8] [c0066ecc] smpboot_thread_fn+0x184/0x1cc
[ec4bff08] [c0062718] kthread+0x140/0x144
[ec4bff38] [c0012350] ret_from_kernel_thread+0x14/0x1c
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX rings have a producer index owned by hardware, where newly
received frame buffers are placed, and a consumer index owned by
software, where newly allocated buffers are placed, in expectation of
hardware being able to place frame data in them.
Hardware increments the producer index when a frame is received, however
it is not allowed to increment the producer index to match the consumer
index (RBCIR) since the ring can hold at most RBLENR[LENGTH]-1 received
BDs. Whenever the producer index matches the value of the consumer
index, the ring has no unprocessed received frames and all BDs in the
ring have been initialized/prepared by software, i.e. hardware owns all
BDs in the ring.
The code uses the next_to_clean variable to keep track of the producer
index, and the next_to_use variable to keep track of the consumer index.
The RX rings are seeded from enetc_refill_rx_ring, which is called from
two places:
1. initially the ring is seeded until full with enetc_bd_unused(rx_ring),
i.e. with 511 buffers. This will make next_to_clean=0 and next_to_use=511:
.ndo_open
-> enetc_open
-> enetc_setup_bdrs
-> enetc_setup_rxbdr
-> enetc_refill_rx_ring
2. then during the data path processing, it is refilled with 16 buffers
at a time:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_clean_rx_ring
-> enetc_refill_rx_ring
There is just one problem: the initial seeding done during .ndo_open
updates just the producer index (ENETC_RBPIR) with 0, and the software
next_to_clean and next_to_use variables. Notably, it will not update the
consumer index to make the hardware aware of the newly added buffers.
Wait, what? So how does it work?
Well, the reset values of the producer index and of the consumer index
of a ring are both zero. As per the description in the second paragraph,
it means that the ring is full of buffers waiting for hardware to put
frames in them, which by coincidence is almost true, because we have in
fact seeded 511 buffers into the ring.
But will the hardware attempt to access the 512th entry of the ring,
which has an invalid BD in it? Well, no, because in order to do that, it
would have to first populate the first 511 entries, and the NAPI
enetc_poll will kick in by then. Eventually, after 16 processed slots
have become available in the RX ring, enetc_clean_rx_ring will call
enetc_refill_rx_ring and then will [ finally ] update the consumer index
with the new software next_to_use variable. From now on, the
next_to_clean and next_to_use variables are in sync with the producer
and consumer ring indices.
So the day is saved, right? Well, not quite. Freeing the memory
allocated for the rings is done in:
enetc_close
-> enetc_clear_bdrs
-> enetc_clear_rxbdr
-> this just disables the ring
-> enetc_free_rxtx_rings
-> enetc_free_rx_ring
-> sets next_to_clean and next_to_use to 0
but again, nothing is committed to the hardware producer and consumer
indices (yay!). The assumption is that the ring is disabled, so the
indices don't matter anyway, and it's the responsibility of the "open"
code path to set those up.
.. Except that the "open" code path does not set those up properly.
While initially, things almost work, during subsequent enetc_close ->
enetc_open sequences, we have problems. To be precise, the enetc_open
that is subsequent to enetc_close will again refill the ring with 511
entries, but it will leave the consumer index untouched. Untouched
means, of course, equal to the value it had before disabling the ring
and draining the old buffers in enetc_close.
But as mentioned, enetc_setup_rxbdr will at least update the producer
index though, through this line of code:
enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);
so at this stage we'll have:
next_to_clean=0 (in hardware 0)
next_to_use=511 (in hardware we'll have the refill index prior to enetc_close)
Again, the next_to_clean and producer index are in sync and set to
correct values, so the driver manages to limp on. Eventually, 16 ring
entries will be consumed by enetc_poll, and the savior
enetc_clean_rx_ring will come and call enetc_refill_rx_ring, and then
update the hardware consumer ring based upon the new next_to_use.
So.. it works?
Well, by coincidence, it almost does, but there's a circumstance where
enetc_clean_rx_ring won't be there to save us. If the previous value of
the consumer index was 15, there's a problem, because the NAPI poll
sequence will only issue a refill when 16 or more buffers have been
consumed.
It's easiest to illustrate this with an example:
ip link set eno0 up
ip addr add 192.168.100.1/24 dev eno0
ping 192.168.100.1 -c 20 # ping this port from another board
ip link set eno0 down
ip link set eno0 up
ping 192.168.100.1 -c 20 # ping it again from the same other board
One by one:
1. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 0)
2. ping 192.168.100.1 -c 20 # ping this port from another board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=15 next_to_clean 14 (in hw 15) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: enetc_refill_rx_ring(16) increments next_to_use by 16 (mod 512) and writes it to hw
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=0 next_to_clean 15 (in hw 16) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 16 (in hw 17) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 17 (in hw 18) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 18 (in hw 19) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 19 (in hw 20) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 20 (in hw 21) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 21 (in hw 22) next_to_use 15 (in hw 15)
20 packets transmitted, 20 packets received, 0% packet loss
3. ip link set eno0 down
enetc_free_rx_ring: next_to_clean 0 (in hw 22), next_to_use 0 (in hw 15)
4. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 15)
5. ping 192.168.100.1 -c 20 # ping it again from the same other board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 15)
20 packets transmitted, 12 packets received, 40% packet loss
And there it dies. No enetc_refill_rx_ring (because cleaned_cnt must be equal
to 15 for that to happen), no nothing. The hardware enters the condition where
the producer (14) + 1 is equal to the consumer (15) index, which makes it
believe it has no more free buffers to put packets in, so it starts discarding
them:
ip netns exec ns0 ethtool -S eno0 | grep -v ': 0'
NIC statistics:
Rx ring 0 discarded frames: 8
Summarized, if the interface receives between 16 and 32 (mod 512) frames
and then there is a link flap, then the port will eventually die with no
way to recover. If it receives less than 16 (mod 512) frames, then the
initial NAPI poll [ before the link flap ] will not update the consumer
index in hardware (it will remain zero) which will be ok when the buffers
are later reinitialized. If more than 32 (mod 512) frames are received,
the initial NAPI poll has the chance to refill the ring twice, updating
the consumer index to at least 32. So after the link flap, the consumer
index is still wrong, but the post-flap NAPI poll gets a chance to
refill the ring once (because it passes through cleaned_cnt=15) and
makes the consumer index be again back in sync with next_to_use.
The solution to this problem is actually simple, we just need to write
next_to_use into the hardware consumer index at enetc_open time, which
always brings it back in sync after an initial buffer seeding process.
The simpler thing would be to put the write to the consumer index into
enetc_refill_rx_ring directly, but there are issues with the MDIO
locking: in the NAPI poll code we have the enetc_lock_mdio() taken from
top-level and we use the unlocked enetc_wr_reg_hot, whereas in
enetc_open, the enetc_lock_mdio() is not taken at the top level, but
instead by each individual enetc_wr_reg, so we are forced to put an
additional enetc_wr_reg in enetc_setup_rxbdr. Better organization of
the code is left as a refactoring exercise.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Station Interface Receive Interrupt Detect Register (SIRXIDR)
contains a 16-bit wide mask of 'interrupt detected' events for each ring
associated with a port. Bit i is write-1-to-clean for RX ring i.
I have no explanation whatsoever how this line of code came to be
inserted in the blamed commit. I checked the downstream versions of that
patch and none of them have it.
The somewhat comical aspect of it is that we're writing a binary number
to the SIRXIDR register, which is derived from enetc_bd_unused(rx_ring).
Since the RX rings have 512 buffer descriptors, we end up writing 511 to
this register, which is 0x1ff, so we are effectively clearing the
'interrupt detected' event for rings 0-8.
This register is not what is used for interrupt handling though - it
only provides a summary for the entire SI. The hardware provides one
separate Interrupt Detect Register per RX ring, which auto-clears upon
read. So there doesn't seem to be any adverse effect caused by this
bogus write.
There is, however, one reason why this should be handled as a bugfix:
next_to_clean _should_ be committed to hardware, just not to that
register, and this was obscuring the fact that it wasn't. This is fixed
in the next patch, and removing the bogus line now allows the fix patch
to be backported beyond that point.
Fixes: fd5736bf9f23 ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ENETC port 0 MAC supports in-band status signaling coming from a PHY
when operating in RGMII mode, and this feature is enabled by default.
It has been reported that RGMII is broken in fixed-link, and that is not
surprising considering the fact that no PHY is attached to the MAC in
that case, but a switch.
This brings us to the topic of the patch: the enetc driver should have
not enabled the optional in-band status signaling for RGMII unconditionally,
but should have forced the speed and duplex to what was resolved by
phylink.
Note that phylink does not accept the RGMII modes as valid for in-band
signaling, and these operate a bit differently than 1000base-x and SGMII
(notably there is no clause 37 state machine so no ACK required from the
MAC, instead the PHY sends extra code words on RXD[3:0] whenever it is
not transmitting something else, so it should be safe to leave a PHY
with this option unconditionally enabled even if we ignore it). The spec
talks about this here:
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/RGMIIv1_5F00_3.pdf
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quoting from the blamed commit:
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Intuitive or not, there isn't any definition issued by a standards body
which says that promiscuity has anything to do with VLAN filtering - it
only has to do with accepting packets regardless of destination MAC address.
In fact people are already trying to use this misunderstanding/bug of
the enetc driver as a justification to transform promiscuity into
something it never was about: accepting every packet (maybe that would
be the "rx-all" netdev feature?):
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
This is relevant because there are use cases in the kernel (such as
tc-flower rules with the protocol 802.1Q and a vlan_id key) which do not
(yet) use the vlan_vid_add API to be compatible with VLAN-filtering NICs
such as enetc, so for those, disabling rx-vlan-filter is currently the
only right solution to make these setups work:
https://lore.kernel.org/netdev/CA+h21hoxwRdhq4y+w8Kwgm74d4cA0xLeiHTrmT-VpSaM7obhkg@mail.gmail.com/
The blamed patch has unintentionally introduced one more way for this to
work, which is to enable IFF_PROMISC, however this is non-portable
because port promiscuity is not meant to disable VLAN filtering.
Therefore, it could invite people to write broken scripts for enetc, and
then wonder why they are broken when migrating to other drivers that
don't handle promiscuity in the same way.
Fixes: 7070eea5e95a ("enetc: permit configuration of rx-vlan-filter with ethtool")
Cc: Markus Blöchl <Markus.Bloechl@ipetronik.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the enetc ports have rx-vlan-offload enabled, they report a TPID of
ETH_P_8021Q regardless of what was actually in the packet. When
rx-vlan-offload is disabled, packets have the proper TPID. Fix this
inconsistency by finishing the TODO left in the code.
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workaround for the ENETC MDIO erratum caused a performance
degradation of 82 Kpps (seen with IP forwarding of two 1Gbps streams of
64B packets). This is due to excessive locking and unlocking in the fast
path, which can be avoided.
By taking the MDIO read-side lock only once per NAPI poll cycle, we are
able to regain 54 Kpps (65%) of the performance hit. The rest of the
performance degradation comes from the TX data path, but unfortunately
it doesn't look like we can optimize that away easily, even with
netdev_xmit_more(), there just isn't any skb batching done, to help with
taking the MDIO lock less often than once per packet.
We need to change the register accessor type for enetc_get_tx_tstamp,
because it now runs under the enetc_lock_mdio as per the new call path
detailed below:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_lock_mdio
-> enetc_clean_tx_ring
-> enetc_get_tx_tstamp
-> enetc_clean_rx_ring
-> enetc_unlock_mdio
Fixes: fd5736bf9f23 ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael reports that since linux-next-20210211, the AER messages for ECC
errors have started reappearing, and this time they can be reliably
reproduced with the first ping on one of his LS1028A boards.
$ ping 1[ 33.258069] pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
72.16.0.1
PING [ 33.267050] pcieport 0000:00:1f.0: AER: can't find device of ID0000
172.16.0.1 (172.16.0.1): 56 data bytes
64 bytes from 172.16.0.1: seq=0 ttl=64 time=17.124 ms
64 bytes from 172.16.0.1: seq=1 ttl=64 time=0.273 ms
$ devmem 0x1f8010e10 32
0xC0000006
It isn't clear why this is necessary, but it seems that for the errors
to go away, we must clear the entire RFS and RSS memory, not just for
the ports in use.
Sadly the code is structured in such a way that we can't have unified
logic for the used and unused ports. For the minimal initialization of
an unused port, we need just to enable and ioremap the PF memory space,
and a control buffer descriptor ring. Unused ports must then free the
CBDR because the driver will exit, but used ports can not pick up from
where that code path left, since the CBDR API does not reinitialize a
ring when setting it up, so its producer and consumer indices are out of
sync between the software and hardware state. So a separate
enetc_init_unused_port function was created, and it gets called right
after the PF memory space is enabled.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Reported-by: Michael Walle <michael@walle.cc>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:
enetc_pf_probe
-> enetc_alloc_si_resources
-> enetc_configure_si
-> enetc_setup_default_rss_table
is overwritten later in:
enetc_pf_probe
-> enetc_init_port_rss_memory
which zero-initializes the entire port RSS table in order to avoid ECC errors.
The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.
The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9788dcc5fe26baafd73bf9242b68900
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current use of container_of is flawed and unnecessary. Obtain
the dpaa_napi_portal reference from the private percpu data instead.
Fixes: a1e031ffb422 ("dpaa_eth: add XDP_REDIRECT support")
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20210218182106.22613-1-camelia.groza@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
The following call path suggests that calling unregister_netdev on an
interface that is up will first bring it down.
enetc_pf_remove
-> unregister_netdev
-> unregister_netdevice_queue
-> unregister_netdevice_many
-> dev_close_many
-> __dev_close_many
-> enetc_close
-> enetc_stop
-> phylink_stop
However, enetc first destroys the phylink instance, then calls
unregister_netdev. This is already dissimilar to the setup (and error
path teardown path) from enetc_pf_probe, but more than that, it is buggy
because it is invalid to call phylink_stop after phylink_destroy.
So let's first unregister the netdev (and let the .ndo_stop events
consume themselves), then destroy the phylink instance, then free the
netdev.
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FSL_ENETC_MDIO use symbols from PHYLIB (MDIO_BUS) and MDIO_DEVRES,
however there are no dependency specified in Kconfig
ERROR: modpost: "__mdiobus_register" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "mdiobus_unregister" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "devm_mdiobus_alloc_size" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
add depends on MDIO_DEVRES && MDIO_BUS
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Add support for backplane link mode, which is, according to discussions
with NXP earlier in the year, is a mode where the OS (Linux) is able to
manage the PCS and Serdes itself.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that pcs-lynx supports 1000BASE-X, add support for this interface
mode to dpaa2-mac. pcs-lynx can be switched at runtime between SGMII
and 1000BASE-X mode, so allow dpaa2-mac to switch between these as
well.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following coccicheck warnings:
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1651:36-38: WARNING
!A || A && B is equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1612260157-128026-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The XDP frame's headroom might be large enough to accommodate the
xdpf backpointer as well as shifting the data to an aligned address.
Try this first before resorting to allocating a new buffer and copying
the data.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 256 byte data alignment is required for preventing DMA transaction
splits when crossing 4K page boundaries. Since XDP deals only with page
sized buffers or less, this restriction isn't needed. Instead, the data
only needs to be aligned to 64 bytes to prevent DMA transaction splits.
These lessened restrictions can increase performance by widening the pool
of permitted data alignments and preventing unnecessary realignments.
Fixes: ae680bcbd06a ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the erratum workaround is triggered, the newly created xdp_frame
structure is stored at the start of the newly allocated buffer. Avoid
the structure from being overwritten by explicitly reserving enough
space in the buffer for storing it.
Account for the fact that the structure's size might increase in time by
aligning the headroom to DPAA_FD_DATA_ALIGNMENT bytes, thus guaranteeing
the data's alignment.
Fixes: ae680bcbd06a ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If CONFIG_M5272=y:
drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_restart’:
drivers/net/ethernet/freescale/fec_main.c:948:6: warning: unused variable ‘val’ [-Wunused-variable]
948 | u32 val;
| ^~~
drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_get_mac’:
drivers/net/ethernet/freescale/fec_main.c:1667:28: warning: unused variable ‘pdata’ [-Wunused-variable]
1667 | struct fec_platform_data *pdata = dev_get_platdata(&fep->pdev->dev);
| ^~~~~
Fix this by moving the variable declarations inside the existing #ifdef
blocks.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210202130650.865023-1-geert@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/can/dev.c
b552766c872f ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e7345 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec991 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c483 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf22870c ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c0c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e96 ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5afe ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fec_restart() does a hard reset of the MAC module when the link status
changes to up. This temporarily resets the R_CNTRL register which controls
the MII mode of the ENET_OUT clock. In the case of RMII, the clock
frequency momentarily drops from 50MHz to 25MHz until the register is
reconfigured. Some link partners do not tolerate this glitch and
invalidate the link causing failure to establish a stable link when using
PHY polling mode. Since as per IEEE802.3 the criteria for link validity
are PHY-specific, what the partner should tolerate cannot be assumed, so
avoid resetting the MII clock by using software reset instead of hardware
reset when the link is up. This is generally relevant only if the SoC
provides the clock to an external PHY and the PHY is configured for RMII.
Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Also decrement the reference count of child device on error path.
Fixes: 3e782985cb3c ("net: ethernet: fec: Allow configuration of MDIO bus speed")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210120122037.83897-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since kmalloc() is nowadays [1] guaranteed to return naturally
aligned (i.e., aligned to the size itself) memory for power-of-2
sizes, we don't need to over-allocate the align amount, compute an
aligned address within the allocation, and (for later freeing) also
storing the original pointer [2].
Instead, just round up the length we want to allocate to the alignment
requirements, then round that up to the next power of 2. In theory,
this could allocate up to about twice as much memory as we needed. In
practice, (a) kmalloc() would in most cases anyway return a
power-of-2-sized allocation and (b) with the default values of the
bdRingLen[RT]x fields, the length is already itself a power of 2
greater than the alignment.
So we actually end up saving memory compared to the current
situtation (e.g. for tx, we currently allocate 128+32 bytes, which
kmalloc() likely rounds up to 192 or 256; with this patch, we just
allocate 128 bytes.) Also struct ucc_geth_private becomes a little
smaller.
[1] 59bb47985c1d ("mm, sl[aou]b: guarantee natural alignment for
kmalloc(power-of-two)")
[2] That storing was anyway done in a u32, which works on 32 bit
machines, but is not very elegant and certainly makes a reader of the
code pause for a while.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The numQueuesTx and numQueuesRx members of struct ucc_geth_info are
never set to anything but 1, and never have been. It's unclear how
well the code supporting multiple queues would work. Until somebody
wants to play with enabling that, help the compiler eliminate a lot of
dead code and loops that are not really loops by creating static
inline helpers. If and when the numQueuesTx/numQueuesRx fields are
re-introduced, it suffices to update those helper to return the
appropriate field.
This cuts the .text segment of ucc_geth.o by 8%.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The translation from the ucc_geth_num_of_threads enum value to the
actual count can be written somewhat more compactly with a small
lookup table, allowing us to replace the four switch statements.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bd_mem_part member of ucc_geth_info always has the value
MEM_PART_SYSTEM, and AFAICT, there has never been any code setting it
to any other value. Moreover, muram is a somewhat precious resource,
so there's no point using that when normal memory serves just as well.
Apart from removing a lot of dead code, this is also motivated by
wanting to clean up the "store result from kmalloc() in a u32" mess.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These macros both have the value 32, there's no point first
initializing align to a lower value.
If anything, one could throw in a
BUILD_BUG_ON(UCC_GETH_TX_BD_RING_ALIGNMENT < 4), but it's not worth it
- lots of code depends on named constants having sensible values.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct ucc_geth_info is somewhat large, and on systems with only one
or two UCC instances, that just wastes a few KB of memory. So
allocate and populate a chunk of memory at probe time instead of
initializing them all during driver init.
Note that the existing "ug_info == NULL" check was dead code, as the
address of some static array element can obviously never be NULL.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce the code duplication a bit by moving the parsing of
rx-clock-name and the fallback handling to a helper function.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These fields are only used within ucc_geth_startup(), so they might as
well be local variables in that function rather than being stashed in
struct ucc_geth_private.
Aside from making that struct a tiny bit smaller, it also shortens
some lines (getting rid of pointless casts while here), and fixes the
problems with using IS_ERR_VALUE() on a u32 as explained in commit
800cd6fb76f0 ("soc: fsl: qe: change return type of cpm_muram_alloc()
to s32").
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These buffers have all just been handed out from qe_muram_alloc(), aka
cpm_muram_alloc(), and the helper cpm_muram_alloc_common() already
does
memset_io(cpm_muram_addr(start), 0, size);
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
