| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Frequent link up/down events can happen when a Bel Fuse SFP part is
connected to the amd-xgbe device. Try to avoid the frequent link
issues by resetting the PHY as documented in Bel Fuse SFP datasheets.
Fixes: e722ec82374b ("amd-xgbe: Update the BelFuse quirk to support SGMII")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, auto negotiation and reconnect should be automatically done by
the hardware. But there seems to be an issue where auto negotiation has
to be restarted manually. This happens because of link training and so
even though still connected to the partner the link never "comes back".
This needs an auto-negotiation restart.
Also, a change in xgbe-mdio is needed to get ethtool to recognize the
link down and get the link change message. This change is only
required in a backplane connection mode.
Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes mailbox commands timeout when the RX data path becomes
unresponsive. This prevents the submission of new mailbox commands to DXIO.
This patch identifies the timeout and resets the RX data path so that the
next message can be submitted properly.
Fixes: 549b32af9f7c ("amd-xgbe: Simplify mailbox interface rate change code")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new port mode that is a backplane connection without
support for auto negotiation.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The conversion to bool is not needed, remove it.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro PHY_GBIT_FEAUTRES needs to change into a bitmap in order to
support link_modes. Remove its use from xgde by replacing it with its
definition.
Probably, the current behavior is wrong. It probably should be
ANDing not assigning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data. These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly. Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a quirk to make the BelFuse 1GBT-SFP06 part look like
a 1000baseX part, program the SFP PHY to support SGMII and 10/100/1000
baseT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a KR re-driver is present, indicate the FEC support is available
during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently sets an indication of whether the SFP supports, and
that the driver can obtain, diagnostics data. This isn't currently used
by the driver and the logic to set this indicator is flawed because the
field is cleared each time the SFP is checked and only set when a new SFP
is detected. Remove this field and the logic supporting it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comm_owned field can hide logic where double locking is attempted
and prevent multiple threads for the same device from accessing the
mutex properly. Remove the comm_owned field and use the mutex API
exclusively for gaining ownership. The current driver has been audited
and is obtaining communications ownership properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read and save the port property registers once during the device probe
and then use the saved values as they are needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert from using the old u32 supported, advertising, etc. link settings
to the new link mode settings that support bit positions / settings
greater than 32 bits.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the MDIO mode is set to none for the 10000Base-T, which is
incorrect. The MDIO mode should for this configuration should be
clause 45.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I2C communication fails, it tends to always fail. Rather than
continuously issue an error message (once per second in most cases),
change the message to be issued just once.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver has some missing functionality when operating in the mode that
supports 2.5GbE. Fix the driver to fully recognize and support this speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using SFPs, the supported and advertised settings should be initially
based on the SFP that has been detected. The code currently indicates the
overall support of the device as opposed to what the SFP is capable of.
Update the code to change the supported link modes, auto-negotiation, etc.
to be based on the installed SFP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify and centralize the mailbox command rate change interface by
having a single function perform the writes to the mailbox registers
to issue the request.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an SFP module is not present, xgbe_phy_sfp_phy_settings() should
return after applying the default settings. Currently there is no return
statement and the default settings are overwritten.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO register mode is set when the device is probed. But when the
device is brought down and then back up, the MDIO register mode has been
reset. Be sure to reset the mode during device startup and only change
the mode of the address specified.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the connection type enumeration for backplane mode and return
an error when there is a mismatch between the mode and the connection
type.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up some warnings that were identified by coccinelle:
Clean up an if/else block that can look confusing since the same statement
is executed in an "else if" check and the final "else" statement.
Change a variable from unsigned int to int since it is used in an if
statement checking the value to be less than 0.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides support for the presence of a KR redriver chip in
between the device PCS and an external PHY. When a redriver chip is
present the device must perform clause 73 auto-negotiation in order to
set the redriver chip for the downstream connection.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the phylib support in the kernel to communicate with and control an
MDIO attached PHY. Use the hardware's MDIO communication mechanism to
communicate with the PHY.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for recognizing and using SFP+ modules directly. This includes
using the I2C support to read and interpret the information returned from
an SFP+ module and configuring things properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to initialize and use the I2C controller within the hardware
in order to perform sideband communication, e.g. determine the SFP media
type that is installed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for new PCI devices to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
