summaryrefslogtreecommitdiff
path: root/drivers/net/e1000e/ich8lan.c
AgeCommit message (Collapse)AuthorFilesLines
2011-03-11e1000e: disable jumbo frames on 82579 when MACsec enabled in EEPROMBruce Allan1-1/+7
If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames support in the driver due to an interoperability issue in hardware that prevents jumbo packets from being transmitted or received. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-11e1000e: do not toggle LANPHYPC value bit when PHY reset is blockedBruce Allan1-4/+4
When PHY reset is intentionally blocked on 82577/8/9, do not toggle the LANPHYPC value bit (essentially performing a hard power reset of the device) otherwise the PHY can be put into an unknown state. Cleanup whitespace in the same function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-11e1000e: extend EEE LPI timer to prevent dropped linkBruce Allan1-5/+24
The link can be unexpectedly dropped when the timer for entering EEE low- power-idle quiet state expires too soon. The timer needs to be extended from 196usec to 200usec after every LCD (PHY) reset to prevent this from happening. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-24e1000e: reduce scope of some variables, remove unnecessary onesBruce Allan1-1/+2
Static analysis of the driver code found some variables for which the scope can be reduced, or remove the variable altogether. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds1-1/+1
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits) GRETH: resolve SMP issues and other problems GRETH: handle frame error interrupts GRETH: avoid writing bad speed/duplex when setting transfer mode GRETH: fixed skb buffer memory leak on frame errors GRETH: GBit transmit descriptor handling optimization GRETH: fix opening/closing GRETH: added raw AMBA vendor/device number to match against. cassini: Fix build bustage on x86. e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs e1000e: update Copyright for 2011 e1000: Avoid unhandled IRQ r8169: keep firmware in memory. netdev: tilepro: Use is_unicast_ether_addr helper etherdevice.h: Add is_unicast_ether_addr function ks8695net: Use default implementation of ethtool_ops::get_link ks8695net: Disable non-working ethtool operations USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable. vxge: Remember to release firmware after upgrading firmware netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr ipsec: update MAX_AH_AUTH_LEN to support sha512 ...
2011-01-14e1000e: update Copyright for 2011Bruce Allan1-1/+1
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-13Merge branch 'for-next' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits) Documentation/trace/events.txt: Remove obsolete sched_signal_send. writeback: fix global_dirty_limits comment runtime -> real-time ppc: fix comment typo singal -> signal drivers: fix comment typo diable -> disable. m68k: fix comment typo diable -> disable. wireless: comment typo fix diable -> disable. media: comment typo fix diable -> disable. remove doc for obsolete dynamic-printk kernel-parameter remove extraneous 'is' from Documentation/iostats.txt Fix spelling milisec -> ms in snd_ps3 module parameter description Fix spelling mistakes in comments Revert conflicting V4L changes i7core_edac: fix typos in comments mm/rmap.c: fix comment sound, ca0106: Fix assignment to 'channel'. hrtimer: fix a typo in comment init/Kconfig: fix typo anon_inodes: fix wrong function name in comment fix comment typos concerning "consistent" poll: fix a typo in comment ... Fix up trivial conflicts in: - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c) - fs/ext4/ext4.h Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-10e1000e: use either_crc_le() rather than re-write itBruce Allan1-18/+1
For the 82579 jumbo frame workaround, there is no need to re-write the CRC calculation functionality already found in the kernel's ether_crc_le(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phyBruce Allan1-29/+25
Cleans up the code a bit by using the driver-specific e1e_rphy and e1e_wphy macros instead of the full function pointer variants. Fix a couple whitespace issue with two already existing calls to e1e_wphy. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-10e1000e: cleanup variables set but not usedBruce Allan1-2/+2
The ICR register is clear on read and we don't care what the returned value is when resetting the hardware so the icr variable(s) can be removed. We should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and from e1000_get_phy_id_82571() (dump a debug message when it fails and when an unknown Phy id is returned). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-25e1000e: checkpatch warnings - bracesBruce Allan1-3/+2
WARNING: braces {} are not necessary for any arm of this statement WARNING: braces {} are not necessary for single statement blocks Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-11e1000e: 82579 PHY incorrectly identified during initBruce Allan1-5/+11
During init, reading the 2 PHY ID registers back-to-back in the default fast mode could return invalid data (all F's) and in slow mode could return data to the second read the data from the first read. To resolve the issue in fast mode, set to slow mode before any PHY accesses; to resolve the issue in slow mode, put in a delay for every 82579 PHY access. Since this PHY is currently only paired with the pch2lan MAC and the PHY type is not known before the first PHY access which can fail this way, check for this based on MAC-type. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-11e1000e: 82577/8/9 mis-configured OEM bits during S0->SxBruce Allan1-1/+1
The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits) were being configured incorrectly when device goes to D3 state. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-11-01tree-wide: fix comment/printk typosUwe Kleine-König1-1/+1
"gadget", "through", "command", "maintain", "maintain", "controller", "address", "between", "initiali[zs]e", "instead", "function", "select", "already", "equal", "access", "management", "hierarchy", "registration", "interest", "relative", "memory", "offset", "already", Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-10-01e1000e: 82579 performance improvementsBruce Allan1-1/+1
The initial support for 82579 was tuned poorly for performance. Adjust the packet buffer allocation appropriately for both standard and jumbo frames; and for jumbo frames increase the receive descriptor pre-fetch, disable adaptive interrupt moderation and set the DMA latency tolerance. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82579 do not gate auto config of PHY by hardware during nominal useBruce Allan1-9/+68
For non-managed versions of 82579, set the bit that prevents the hardware from automatically configuring the PHY after resets only when the driver performs a reset, clear the bit after resets. This is so the hardware can configure the PHY automatically when the part is reset in a manner that is not controlled by the driver (e.g. in a virtual environment via PCI FLR) otherwise the PHY will be mis-configured causing issues such as failing to link at 1000Mbps. For managed versions of 82579, keep the previous behavior since the manageability firmware will handle the PHY configuration. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82579 jumbo frame workaround causing CRC errorsBruce Allan1-11/+1
The subject workaround was causing CRC errors due to writing the wrong register with updates of the RCTL register. It was also found that the workaround function which modifies the RCTL register was being called in the middle of a read-modify-write operation of the RCTL register, so the function call has been moved appropriately. Lastly, jumbo frames must not be allowed when CRC stripping is disabled by a module parameter because the workaround requires the CRC be stripped. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82579 unaccounted missed packetsBruce Allan1-0/+48
On 82579, there is a hardware bug that can cause received packets to not get transferred from the PHY to the MAC due to K1 (a power saving feature of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls the accounting of missed packets, these will go unnoticed. Workaround the issue by setting the K1 beacon duration according to the link speed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82566DC fails to get linkBruce Allan1-2/+5
Two recent patches to cleanup the reset[1] and initial PHY configuration[2] code paths for ICH/PCH devices inadvertently left out a 10msec delay and device ID check respectively which are necessary for the 82566DC (device id 0x104b) to be configured properly, otherwise it will not get link. [1] commit e98cac447cc1cc418dff1d610a5c79c4f2bdec7f [2] commit 3f0c16e84438d657d29446f85fe375794a93f159 CC: stable@kernel.org Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82579 SMBus address and LEDs incorrect after device resetBruce Allan1-3/+3
Since the hardware is prevented from performing automatic PHY configuration (the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL register will not get cleared preventing the SMBus address and the LED configuration to be written to the PHY registers. On 82579, do not check the OEM_WRITE_ENABLE bit. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23e1000e: 82577/8/9 issues with device in SxBruce Allan1-8/+39
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan) in addition to the MAC before configuring PHY wakeup otherwise the PHY configuration writes might be missed. Also write the LED configuration and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and e1000_write_smbus_addr, respectively). The reset is no longer needed since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and leaving it in causes issues with auto-negotiating the link. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30e1000e: disable EEE support by defaultBruce Allan1-0/+4
Based on community feedback, EEE should be disabled by default until the IEEE802.3az specification has been finalized. Cc: bhutchings@solarflare.com Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: disable gig speed when in S0->Sx transitionBruce Allan1-14/+5
Most of this workaround is necessary for all ICHx/PCH parts so one of the two MAC-type checks can be removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: update copyright informationBruce Allan1-1/+1
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: enable support for EEE on 82579Bruce Allan1-1/+40
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the new 82579 LOMs. An optional module parameter is provided to disable the feature if desired. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: initial support for 82579 LOMsBruce Allan1-17/+311
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: fix check for manageability on ICHx/PCHBruce Allan1-4/+27
Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for manageability on 82577/82578; only check if iAMT is enabled. Both of the manageability checks (for 82577/82578 and ICHx) must check the firmware valid bit too since the other bits are only valid when the latter is set. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: separate out PHY statistics register updatesBruce Allan1-0/+1
The 82577/82578 parts have half-duplex statistics in PHY registers. These need only be read when in half-duplex and should all be read at once rather than one at a time to prevent excessive cycles of acquiring/releasing the PHY semaphore. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-19e1000e: cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan1-13/+19
Do not acquire and release the PHY unnecessarily for parts that return from this workaround without actually accessing the PHY registers. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14drivers/net: Remove unnecessary returns from void function()sJoe Perches1-10/+0
This patch removes from drivers/net/ all the unnecessary return; statements that precede the last closing brace of void functions. It does not remove the returns that are immediately preceded by a label as gcc doesn't like that. It also does not remove null void functions with return. Done via: $ grep -rP --include=*.[ch] -l "return;\n}" net/ | \ xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }' with some cleanups by hand. Compile tested x86 allmodconfig only. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: Fix/cleanup PHY reset code for ICHx/PCHxBruce Allan1-74/+75
i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to make sure the MAC had completed the PHY configuration. However, e1000_lan_init_done_ich8lan() had already been called in one of the two places where PHY reset occurs for ICHx/PCHx parts, which caused the second call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already been checked and cleared. ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset in e1000_reset_hw_ich8lan() and the PHY-only reset in e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be performed post-reset that are now combined into one new function - e1000_post_phy_reset_ich8lan(). This cleanup also included moving the clearing of the PHY Reset Asserted bit in the STATUS register (now done for all ICH/PCH parts) and the check for the indication from h/w that basic configuration has completed back to where it previously was in e1000_get_cfg_done_ich8lan(). iii) Corrected a few comments Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: move settting of flow control refresh timer to link setup codeBruce Allan1-0/+2
The flow control refresh timer value needs to be saved off so that it can be programmed into the approrpiate register when applicable but without a reset, e.g. when changing flow control parameters via ethtool. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: fix checks for manageability enabled and management pass-throughBruce Allan1-2/+4
The mac->arc_subsystem was being incorrectly used to flag whether or not manageability was enabled when it should only be used to state whether the ARC (Host interface) subsystem is available on a particular MAC _and_ only valid when any manageability is enabled. The ARC subsystem is currently only available on 80003es2lan and 82573 parts supported by the driver. A new flag, has_fwsm, is introduced to be used when checking if manageability is enabled but only on parts that acutally have an FWSM register. While the above parts have an FWSM register, there are other parts that have FWSM but do not have support for the ARC subsystem, namely 82571/2 and ICHx/PCH. And then there are parts that have manageability, but do not have either FWSM register or support for the ARC subsystem - these are 82574 and 82583. For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no functional changes, it only corrects the usage of the manageability flags. For 82574 and 82583, it fixes the incorrect accesses of the non-existent FWSM register and ARC subsystem as well as corrects the check for management pass-through. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: Incorrect function pointer set for force_speed_duplex on 82577Bruce Allan1-0/+1
The force_speed_duplex function pointer was incorrectly set. Instead of calling the 82577-specific version it was calling the m88 version which, among other incorrect things, reset the PHY causing autonegotiation to be re-enabled in the PHY resulting in the link defaulting to half-duplex. The 82577-specific force_speed_duplex function also had an issue where it disabled Auto-MDI-X which caused the link to not come up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: Cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan1-77/+75
After every reset all ICH/PCH parts call this function which acquires the swflag, performs a workaround on applicable parts and releases the swflag. There is no reason for parts for which this workaround is not applicable to acquire and release the swflag so the function should just return without doing anything for these parts. This also provides for the indentation of most of the function contents to be shifted left cleaning up the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-13e1000e: cleanup multiple common exit pointsBruce Allan1-24/+17
...in e1000_update_nvm_checksum_ich8lan(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06e1000e: Reset 82577/82578 PHY before first PHY register readBruce Allan1-0/+10
Reset the PHY before first accessing it. Doing so, ensure that the PHY is in a known good state before we read/write PHY registers. This fixes a driver probe failure. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06e1000e: reset MAC-PHY interconnect on 82577/82578 during Sx->S0Bruce Allan1-0/+20
During Sx->S0 transitions, the interconnect between the MAC and PHY on 82577/82578 can remain in SMBus mode instead of transitioning to the PCIe-like mode required during normal operation. Toggling the LANPHYPC Value bit essentially resets the interconnect forcing it to the correct mode. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-31e1000e: typo correctionsJoe Perches1-3/+3
Here are the other miscellaneous corrections done by an earlier larger suggested patch now made unnecessary by a less invasive change. Correct a few missing newlines from logging messages and a typo fix. Fix speed/duplex logging message. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-06e1000e: fix packet corruption and tx hang during NFSv2Jesse Brandeburg1-0/+10
when receiving a particular type of NFS v2 UDP traffic, the hardware could DMA some bad data and then hang, possibly corrupting memory. Disable the NFS parsing in this hardware, verified to fix the bug. Originally reported and reproduced by RedHat's Neil Horman CC: nhorman@tuxdriver.com Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23Merge branch 'master' of ↵David S. Miller1-5/+71
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2010-01-14e1000e: provide MAC-family-specific function to set LAN IDBruce Allan1-0/+1
Provide MAC-specific function pointer to determine the LAN ID (PCI func). The LAN ID is used internally by the driver to determine which h/w lock to use to protect accessing the PHY on ESB2 as well as help to determine the alternate MAC address on some parts. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14e1000e: workaround link issues on busy hub in half duplex on 82577/82578Bruce Allan1-1/+18
This patch removes a delay in hardware after every received packet allowing more time for transmitted packets to go out in between received packets in half duplex. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-14e1000e: MDIO slow mode should always be done for 82577Bruce Allan1-4/+53
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: perform 10/100 adaptive IFS only on parts that support itBruce Allan1-0/+2
Adaptive IFS which involves writing to the Adaptive IFS Throttle register was being done for all devices supported by the driver even though it is not supported (i.e. the register doesn't even exist) on some devices. The feature is supported on 8257x/82583 and ICH/PCH based devices, but not on ESB2. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-09e1000e: replace incorrect use of GG82563_REG macroBruce Allan1-3/+5
The GG82563_REG() macro should not be used to determine the offset provided to the e1000e_[read|write]_kmrn_reg() functions since the first argument to the macro is already implied and gets masked off anyway in the functions. The resultant register reads/writes with this patch are functionally the same as before. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03e1000e: correct ICH/PCH PHY operations function pointersBruce Allan1-195/+21
Some function pointers for a few PHY operations (for 82578 and 82567) and were set incorrectly causing functions to be executed that were accessing incorrect PHY register offsets for that particular device. This patch also moves a few PHY-specific functions from ich8lan.c to the more appropriate phy.c. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: add debug messagesBruce Allan1-1/+3
Add some helpful debug messages. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: comment correctionsBruce Allan1-3/+2
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: enable new 82567V-3 deviceBruce Allan1-0/+1
This new PCI device ID is for a new combination of MAC and PHY both of which already have supporting code in the driver, just not yet in this combination. During validation of the device, an intermittent issue was discovered with waking it from a suspended state which can be resolved with the pre-existing workaround to disable gigabit speed prior to suspending. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-14 10:25:06 +0300