summaryrefslogtreecommitdiff
path: root/drivers/net/dsa
AgeCommit message (Collapse)AuthorFilesLines
2020-01-27net: dsa: qca8k: Enable delay for RGMII_ID modeVinod Koul2-0/+13
[ Upstream commit a968b5e9d5879f9535d6099505f9e14abcafb623 ] RGMII_ID specifies that we should have internal delay, so resurrect the delay addition routine but under the RGMII_ID mode. Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode") Tested-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-27net: dsa: b53: Do not program CPU port's PVIDFlorian Fainelli1-1/+1
[ Upstream commit 10163aaee9671b01b2f4737922e1a4f43581047a ] The CPU port is special and does not need to obey VLAN restrictions as far as untagged traffic goes, also, having the CPU port be part of a particular PVID is against the idea of keeping it tagged in all VLANs. Fixes: ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all VLANs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-27net: dsa: b53: Properly account for VLAN filteringFlorian Fainelli2-5/+57
[ Upstream commit dad8d7c6452b5b9f9828c9e2c7ca143205fd40c7 ] VLAN filtering can be built into the kernel, and also dynamically turned on/off through the bridge master device. Allow re-configuring the switch appropriately to account for that by deciding whether VLAN table (v_table) misses should lead to a drop or forward. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-27net: dsa: b53: Fix default VLAN IDFlorian Fainelli1-13/+16
[ Upstream commit fea83353177a55540c71c140887737c282137aa2 ] We were not consistent in how the default VID of a given port was defined, b53_br_leave() would make sure the VLAN ID would be either 0/1 depending on the switch generation, but b53_configure_vlan(), which is the default configuration would unconditionally set it to 1. The correct value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that mistake ever again, introduce a helper function: b53_default_pvid() to factor that out. Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-01-12net: dsa: mv88e6xxx: Preserve priority when setting CPU port.Andrew Lunn2-0/+6
[ Upstream commit d8dc2c9676e614ef62f54a155b50076888c8a29a ] The 6390 family uses an extended register to set the port connected to the CPU. The lower 5 bits indicate the port, the upper three bits are the priority of the frames as they pass through the switch, what egress queue they should use, etc. Since frames being set to the CPU are typically management frames, BPDU, IGMP, ARP, etc set the priority to 7, the reset default, and the highest. Fixes: 33641994a676 ("net: dsa: mv88e6xxx: Monitor and Management tables") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31net: dsa: LAN9303: select REGMAP when LAN9303 enableMao Wenan1-0/+1
[ Upstream commit b6989d248a2d13f02895bae1a9321b3bbccc0283 ] When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y, below errors can be seen: drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE undeclared here (not in a function) .reg_format_endian = REGMAP_ENDIAN_LITTLE, drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config has no member named reg_read .reg_read = lan9303_mdio_read, It should select REGMAP in config NET_DSA_SMSC_LAN9303. Fixes: dc7005831523 ("net: dsa: LAN9303: add MDIO managed mode support") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-13net: dsa: mv88e6xxx: Work around mv886e6161 SERDES missing MII_PHYSID2Andrew Lunn1-5/+16
[ Upstream commit ddc49acb659a2d8bfc5fdb0de0ef197712c11d75 ] We already have a workaround for a couple of switches whose internal PHYs only have the Marvel OUI, but no model number. We detect such PHYs and give them the 6390 ID as the model number. However the mv88e6161 has two SERDES interfaces in the same address range as its internal PHYs. These suffer from the same problem, the Marvell OUI, but no model number. As a result, these SERDES interfaces were getting the same PHY ID as the mv88e6390, even though they are not PHYs, and the Marvell PHY driver was trying to drive them. Add a special case to stop this from happen. Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-05net: dsa: bcm_sf2: Propagate error value from mdio_writeKangjie Lu1-4/+3
[ Upstream commit e49505f7255be8ced695919c08a29bf2c3d79616 ] Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's return their error codes upstream. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-01net: dsa: bcm_sf2: Turn on PHY to allow successful registrationFlorian Fainelli1-0/+4
[ Upstream commit c04a17d2a9ccf1eaba1c5a56f83e997540a70556 ] We are binding to the PHY using the SF2 slave MDIO bus that we create, binding involves reading the PHY's MII_PHYSID1/2 which won't be possible if the PHY is turned off. Temporarily turn it on/off for the bus probing to succeeed. This fixes unbind/bind problems where the port connecting to that PHY would be in error since it could not connect to it. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-01net: dsa: mv88e6xxx: Fix 88E6141/6341 2500mbps SERDES speedMarek Behún3-4/+26
[ Upstream commit 26422340da467538cd65eaa9c65538039ee99c8c ] This is a fix for the port_set_speed method for the Topaz family. Currently the same method is used as for the Peridot family, but this is wrong for the SERDES port. On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot. Moreover setting alt_bit on Topaz only makes sense for port 0 (for (differentiating 100mbps vs 200mbps). The SERDES port does not support more than 2500mbps, so alt_bit does not make any difference. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-10net: dsa: b53: Do not clear existing mirrored port maskFlorian Fainelli1-1/+0
[ Upstream commit c763ac436b668d7417f0979430ec0312ede4093d ] Clearing the existing bitmask of mirrored ports essentially prevents us from capturing more than one port at any given time. This is clearly wrong, do not clear the bitmask prior to setting up the new port. Reported-by: Hubert Feurstein <h.feurstein@gmail.com> Fixes: ed3af5fd08eb ("net: dsa: b53: Add support for port mirroring") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-10net: dsa: bcm_sf2: Fix IMP setup for port different than 8Florian Fainelli1-15/+21
[ Upstream commit 5fc0f21246e50afdf318b5a3a941f7f4f57b8947 ] Since it became possible for the DSA core to use a CPU port different than 8, our bcm_sf2_imp_setup() function was broken because it assumes that registers are applicable to port 8. In particular, the port's MAC is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS bits if we are not configured for port 8. Fixes: 9f91484f6fcc ("net: dsa: make "label" property optional for dsa2") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-06net: dsa: mv88e6xxx: Release lock while requesting IRQAndrew Lunn1-0/+2
[ Upstream commit 342a0ee70acbee97fdeb91349420f8744eb291fb ] There is no need to hold the register lock while requesting the GPIO interrupt. By not holding it we can also avoid a false positive lockdep splat. Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-10-29net: dsa: rtl8366rb: add missing of_node_put after calling of_get_child_by_nameWen Yang1-6/+10
[ Upstream commit f32eb9d80470dab05df26b6efd02d653c72e6a11 ] of_node_put needs to be called when the device node which is got from of_get_child_by_name finished using. irq_domain_add_linear() also calls of_node_get() to increase refcount, so irq_domain will not be affected when it is released. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-10-29net: dsa: qca8k: Use up to 7 ports for all operationsMichal Vokáč1-2/+2
[ Upstream commit 7ae6d93c8f052b7a77ba56ed0f654e22a2876739 ] The QCA8K family supports up to 7 ports. So use the existing QCA8K_NUM_PORTS define to allocate the switch structure and limit all operations with the switch ports. This was not an issue until commit 0394a63acfe2 ("net: dsa: enable and disable all ports") disabled all unused ports. Since the unused ports 7-11 are outside of the correct register range on this switch some registers were rewritten with invalid content. Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Fixes: a0c02161ecfc ("net: dsa: variable number of ports") Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-10-07net: dsa: rtl8366: Check VLAN ID and not portsLinus Walleij1-4/+7
[ Upstream commit e8521e53cca584ddf8ec4584d3c550a6c65f88c4 ] There has been some confusion between the port number and the VLAN ID in this driver. What we need to check for validity is the VLAN ID, nothing else. The current confusion came from assigning a few default VLANs for default routing and we need to rewrite that properly. Instead of checking if the port number is a valid VLAN ID, check the actual VLAN IDs passed in to the callback one by one as expected. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-28net: dsa: mv88e6xxx: wait after reset deactivationBaruch Siach1-0/+2
[ Upstream commit 7b75e49de424ceb53d13e60f35d0a73765626fda ] Add a 1ms delay after reset deactivation. Otherwise the chip returns bogus ID value. This is observed with 88E6390 (Peridot) chip. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-14net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()Rasmus Villemoes1-1/+1
[ Upstream commit 48620e341659f6e4b978ec229f6944dabe6df709 ] The comment is correct, but the code ends up moving the bits four places too far, into the VTUOp field. Fixes: 11ea809f1a74 (net: dsa: mv88e6xxx: support 256 databases) Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-25net: dsa: mv88e6xxx: avoid error message on remove from VLAN 0Nikita Yushchenko1-1/+1
[ Upstream commit 62394708f3e01c9f2be6be74eb6305bae1ed924f ] When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error message is logged: failed to kill vid 0081/0 for device eth_cu_1000_4 This is caused by call from __vlan_vid_del() with vin set to zero, over call chain this results into _mv88e6xxx_port_vlan_del() called with vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL. On symmetric path moving port up, call goes through mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan() that returns -EOPNOTSUPP for zero vid. This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for zero vid, then this error code is explicitly cleared in dsa_slave_vlan_rx_kill_vid() and error message is no longer logged. Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-22net: dsa: rtl8366: Fix up VLAN filteringLinus Walleij1-3/+4
[ Upstream commit 760c80b70bed2cd01630e8595d1bbde910339f31 ] We get this regression when using RTL8366RB as part of a bridge with OpenWrt: WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291 switchdev_port_attr_set_now+0x80/0xa4 lan0: Commit of attribute (id=7) failed. (...) realtek-smi switch lan0: failed to initialize vlan filtering on this port This is because it is trying to disable VLAN filtering on VLAN0, as we have forgot to add 1 to the port number to get the right VLAN in rtl8366_vlan_filtering(): when we initialize the VLAN we associate VLAN1 with port 0, VLAN2 with port 1 etc, so we need to add 1 to the port offset. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-04net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORTRasmus Villemoes1-1/+1
[ Upstream commit 84b3fd1fc9592d431e23b077e692fa4e3fd0f086 ] Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends up in bits 47:32 of the return value, instead of bits 31:16 as they should. Fixes: 6e46e2d821bb ("net: dsa: mv88e6xxx: Fix u64 statistics") Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-16net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmodeHeiner Kallweit1-8/+16
[ Upstream commit 5ceaeb99ffb4dc002d20f6ac243c19a85e2c7a76 ] This patches fixes few issues in mv88e6390x_port_set_cmode(). 1. When entering the function the old cmode may be 0, in this case mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail out and have no chance to set a new mode. Therefore deal properly with -ENODEV. 2. Once we have disabled power and irq, let's set the cached cmode to 0. This reflects the actual status and is cleaner if we bail out with an error in the following function calls. 3. The cached cmode is used by mv88e6390x_serdes_get_lane(), mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable(). Currently we set the cached mode to the new one at the very end of the function only, means until then we use the old one what may be wrong. 4. When calling mv88e6390_serdes_irq_enable() we use the lane value belonging to the old cmode. Get the lane belonging to the new cmode before calling this function. It's hard to provide a good "Fixes" tag because quite a few smaller changes have been done to the code in question recently. Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
2019-05-05net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfcDan Carpenter1-0/+6
[ Upstream commit f949a12fd697479f68d99dc65e9bbab68ee49043 ] The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc(). We can't pass unclamped values to test_bit() or it results in an out of bounds access beyond the end of the bitmap. Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-02net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new ↵Heiner Kallweit1-0/+1
DSA framework [ Upstream commit 3acca1dd17060332cfab15693733cdaf9fba1c90 ] In the original patch I missed to add mv88e6xxx_ports_cmode_init() to the second probe function, the one for the new DSA framework. Fixes: ed8fe20205ac ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode") Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-05net: dsa: mv88e6xxx: Add lockdep classes to fix false positive splatAndrew Lunn1-0/+8
[ Upstream commit f6d9758b12660484b6639364cc406da92a918c96 ] The following false positive lockdep splat has been observed. ====================================================== WARNING: possible circular locking dependency detected 4.20.0+ #302 Not tainted ------------------------------------------------------ systemd-udevd/160 is trying to acquire lock: edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704 but task is already holding lock: edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&desc->request_mutex){+.+.}: mutex_lock_nested+0x1c/0x24 __setup_irq+0xa0/0x704 request_threaded_irq+0xd0/0x150 mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx] mdio_probe+0x2c/0x54 really_probe+0x200/0x2c4 driver_probe_device+0x5c/0x174 __driver_attach+0xd8/0xdc bus_for_each_dev+0x58/0x7c bus_add_driver+0xe4/0x1f0 driver_register+0x7c/0x110 mdio_driver_register+0x24/0x58 do_one_initcall+0x74/0x2e8 do_init_module+0x60/0x1d0 load_module+0x1968/0x1ff4 sys_finit_module+0x8c/0x98 ret_fast_syscall+0x0/0x28 0xbedf2ae8 -> #0 (&chip->reg_lock){+.+.}: __mutex_lock+0x50/0x8b8 mutex_lock_nested+0x1c/0x24 __setup_irq+0x640/0x704 request_threaded_irq+0xd0/0x150 mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx] mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx] mdio_probe+0x2c/0x54 really_probe+0x200/0x2c4 driver_probe_device+0x5c/0x174 __driver_attach+0xd8/0xdc bus_for_each_dev+0x58/0x7c bus_add_driver+0xe4/0x1f0 driver_register+0x7c/0x110 mdio_driver_register+0x24/0x58 do_one_initcall+0x74/0x2e8 do_init_module+0x60/0x1d0 load_module+0x1968/0x1ff4 sys_finit_module+0x8c/0x98 ret_fast_syscall+0x0/0x28 0xbedf2ae8 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&desc->request_mutex); lock(&chip->reg_lock); lock(&desc->request_mutex); lock(&chip->reg_lock); &desc->request_mutex refer to two different mutex. #1 is the GPIO for the chip interrupt. #2 is the chained interrupt between global 1 and global 2. Add lockdep classes to the GPIO interrupt to avoid this. Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-03net: dsa: qca8k: remove leftover phy accessorsChristian Lamparter1-18/+0
commit 1eec7151ae0e134bd42e3f128066b2ff8da21393 upstream. This belated patch implements Andrew Lunn's request of "remove the phy_read() and phy_write() functions." <https://lore.kernel.org/patchwork/comment/902734/> While seemingly harmless, this causes the switch's user port PHYs to get registered twice. This is because the DSA subsystem will create a slave mdio-bus not knowing that the qca8k_phy_(read|write) accessors operate on the external mdio-bus. So the same "bus" gets effectively duplicated. Cc: stable@vger.kernel.org Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-23net: dsa: bcm_sf2: Do not assume DSA master supports WoLFlorian Fainelli1-4/+6
[ Upstream commit c3152ec4c0691e351f35a2f63347a464b5f35151 ] We assume in the bcm_sf2 driver that the DSA master network device supports ethtool_ops::{get,set}_wol operations, which is not a given. Avoid de-referencing potentially non-existent function pointers and check them as we should. Fixes: 96e65d7f3f88 ("net: dsa: bcm_sf2: add support for Wake-on-LAN") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-23net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()Dan Carpenter1-1/+1
[ Upstream commit 8d6ea932856c7087ce8c3d0e79494b7d5386f962 ] The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[] array is allocated in dsa_switch_alloc() and it has ds->num_ports elements so this leads to a static checker warning about a potential out of bounds read. Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-10net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmodeHeiner Kallweit3-0/+15
[ Upstream commit ed8fe20205ac054bf585156709de3913d1890f30 ] When debugging another issue I faced an interrupt storm in this driver (88E6390, port 9 in SGMII mode), consisting of alternating link-up / link-down interrupts. Analysis showed that the driver wanted to set a cmode that was set already. But so far mv88e6390x_port_set_cmode() doesn't check this and powers down SERDES, what causes the link to break, and eventually results in the described interrupt storm. Fix this by checking whether the cmode actually changes. We want that the very first call to mv88e6390x_port_set_cmode() always configures the registers, therefore initialize port.cmode with a value that is different from any supported cmode value. We have to take care that we only init the ports cmode once chip->info->num_ports is set. v2: - add small helper and init the number of actual ports only Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-10net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390XMaxime Chevallier1-2/+2
[ Upstream commit d235c48b40d399328585a68f3f9bf7cc3062d586 ] Upon setting the cmode on 6390 and 6390X, the associated serdes interfaces must be powered off/on. Both 6390X and 6390 share code to do so, but it currently uses the 6390 specific helper mv88e6390_serdes_power() to disable and enable the serdes interface. This call will fail silently on 6390X when trying so set a 10G interface such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs the lane number based on modes supported by the 6390, and returns 0 when getting -ENODEV as a lane number. Using mv88e6390x_serdes_power() should be safe here, since we explicitly rule-out all ports but the 9 and 10, and because modes supported by 6390 ports 9 and 10 are a subset of those supported on 6390X. This was tested on 6390X using RXAUI mode. Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-10net: dsa: mv88e6xxx: Fix u64 statisticsAndrew Lunn1-1/+1
[ Upstream commit 6e46e2d821bb22b285ae8187959096b65d063b0d ] The switch maintains u64 counters for the number of octets sent and received. These are kept as two u32's which need to be combined. Fix the combing, which wrongly worked on u16's. Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-10net: dsa: mv88e6xxx: Fix statistics on mv88e6161Andrew Lunn1-1/+1
[ Upstream commit a6da21bb0eae459a375d5bd48baed821d14301d0 ] Despite what the datesheet says, the silicon implements the older way of snapshoting the statistics. Change the op. Reported-by: Chris.Healy@zii.aero Tested-by: Chris.Healy@zii.aero Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-10net: dsa: mv8e6xxx: fix number of internal PHYs for 88E6x90 familyHeiner Kallweit1-6/+6
[ Upstream commit 95150f29ae480276e76368cdf8a9524b5a96c0ca ] Ports 9 and 10 don't have internal PHY's but are (dependent on the version) SERDES/SGMII/XAUI/RXAUI ports. v2: - fix it for all 88E6x90 family members Fixes: bc3931557d1d ("net: dsa: mv88e6xxx: Add number of internal PHYs") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-10net: dsa: mv88e6xxx: handle unknown duplex modes gracefully in ↵Heiner Kallweit1-1/+1
mv88e6xxx_port_set_duplex [ Upstream commit c6195a8bdfc62a7cecf7df685e64847a4b700275 ] When testing another issue I faced the problem that mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed as argument to mv88e6xxx_port_set_duplex(). We should handle this case gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed() is doing it. Fixes: 7f1ae07b51e8 ("net: dsa: mv88e6xxx: add port duplex setter") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-23dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exitJohn David Anglin1-6/+22
[ Upstream commit 7c0db24cc431e2196d98a5d5ddaa9088e2fcbfe5 ] The GPIO interrupt controller on the espressobin board only supports edge interrupts. If one enables the use of hardware interrupts in the device tree for the 88E6341, it is possible to miss an edge. When this happens, the INTn pin on the Marvell switch is stuck low and no further interrupts occur. I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are directly cleared by reading the Global 1 status register. However, the device interrupt flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced. This is done by reading the relevant SERDES and PHY status register. The code only services interrupts whose status bit is set at the time of reading its status register. If an interrupt event occurs after its status is read and before all interrupts are serviced, then this event will not be serviced and the INTn output pin will remain low. This is not a problem with polling or level interrupts since the handler will be called again to process the event. However, it's a big problem when using level interrupts. The fix presented here is to add a loop around the code servicing switch interrupts. If any pending interrupts remain after the current set has been handled, we loop and process the new set. If there are no pending interrupts after servicing, we are sure that INTn has gone high and we will get an edge when a new event occurs. Tested on espressobin board. Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.") Signed-off-by: John David Anglin <dave.anglin@bell.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12net: dsa: mv88e6xxx: Fix counting of ATU violationsAndrew Lunn1-9/+12
[ Upstream commit 75c05a74e745ae7d663b04d75777af80ada2233c ] The ATU port vector contains a bit per port of the switch. The code wrongly used it as a port number, and incremented a port counter. This resulted in the wrong interfaces counter being incremented, and potentially going off the end of the array of ports. Fix this by using the source port ID for the violation, which really is a port number. Reported-by: Chris Healy <Chris.Healy@zii.aero> Tested-by: Chris Healy <Chris.Healy@zii.aero> Fixes: 65f60e4582bd ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-26net: dsa: mv88x6xxx: mv88e6390 errataAndrew Lunn3-0/+128
[ Upstream commit ea89098ef9a574bceca00d3b5df14aaf0b3f9ccf ] The 6390 copper ports have an errata which require poking magic values into undocumented magic registers and then performing a software reset. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22net: dsa: realtek-smi: fix OF child-node lookupJohan Hovold1-5/+13
commit 3f1bb6abdf19cfa89860b3bc9e7f31b44b6a0ba1 upstream. Use the new of_get_compatible_child() helper to look up child nodes to avoid ever matching non-child nodes elsewhere in the tree. Also fix up the related struct device_node leaks. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241cb0 Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-21mv88e6060: disable hardware level MAC learningAnderson Luiz Alves1-7/+3
[ Upstream commit a74515604a7b171f2702bdcbd1e231225fb456d0 ] Disable hardware level MAC learning because it breaks station roaming. When enabled it drops all frames that arrive from a MAC address that is on a different port at learning table. Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2018-11-23net: dsa: microchip: initialize mutex before useTristram Ha1-5/+5
[ Upstream commit 284fb78ed7572117846f8e1d1d8e3dbfd16880c2 ] Initialize mutex before use. Avoid kernel complaint when CONFIG_DEBUG_LOCK_ALLOC is enabled. Fixes: b987e98e50ab90e5 ("dsa: add DSA switch driver for Microchip KSZ9477") Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-23net: dsa: mv88e6xxx: Fix clearing of stats countersAndrew Lunn1-0/+2
[ Upstream commit a9049ff9214da68df1179a7d5e36b43479abc9b8 ] The mv88e6161 would sometime fail to probe with a timeout waiting for the switch to complete an operation. This operation is supposed to clear the statistics counters. However, due to a read/modify/write, without the needed mask, the operation actually carried out was more random, with invalid parameters, resulting in the switch not responding. We need to preserve the histogram mode bits, so apply a mask to keep them. Reported-by: Chris Healy <Chris.Healy@zii.aero> Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-13net: dsa: mv88e6xxx: Fix writing to a PHY page.Andrew Lunn1-0/+3
[ Upstream commit c309b158090d788e96ee597444965cb79b040484 ] After changing to the needed page, actually write the value to the register! Fixes: 09cb7dfd3f14 ("net: dsa: mv88e6xxx: describe PHY page and SerDes") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-12net: dsa: bcm_sf2: Call setup during switch resumeFlorian Fainelli1-9/+1
There is no reason to open code what the switch setup function does, in fact, because we just issued a switch reset, we would make all the register get their default values, including for instance, having unused port be enabled again and wasting power and leading to an inappropriate switch core clock being selected. Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-12net: dsa: bcm_sf2: Fix unbind orderingFlorian Fainelli1-2/+2
The order in which we release resources is unfortunately leading to bus errors while dismantling the port. This is because we set priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now permissible to clock gate the switch. Later on, when dsa_slave_destroy() comes in from dsa_unregister_switch() and calls dsa_switch_ops::port_disable, we perform the same dismantling again, and this time we hit registers that are clock gated. Make sure that dsa_unregister_switch() is the first thing that happens, which takes care of releasing all user visible resources, then proceed with clock gating hardware. We still need to set priv->wol_ports_mask to 0 to make sure that an enabled port properly gets disabled in case it was previously used as part of Wake-on-LAN. Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05net: dsa: b53: Keep CPU port as tagged in all VLANsFlorian Fainelli1-2/+2
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly") was a bit too trigger happy in removing the CPU port from the VLAN membership because we rely on DSA to program the CPU port VLAN, which it does, except it does not bother itself with tagged/untagged and just usese untagged. Having the CPU port "follow" the user ports tagged/untagged is not great and does not allow for properly differentiating, so keep the CPU port tagged in all VLANs. Reported-by: Gerhard Wiesinger <lists@wiesinger.com> Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17net: dsa: mv88e6xxx: Fix ATU Miss ViolationAndrew Lunn2-2/+2
Fix a cut/paste error and a typo which results in ATU miss violations not being reported. Fixes: 0977644c5005 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-16net: dsa: add support for ksz9897 ethernet switchLad, Prabhakar2-0/+10
ksz9477 is superset of ksz9xx series, driver just works out of the box for ksz9897 chip with this patch. Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-14net: dsa: mv88e6xxx: missing unlock on error pathDan Carpenter1-1/+1
We added a new error path, but we need to drop the lock before we return. Fixes: 2d2e1dd29962 ("net: dsa: mv88e6xxx: Cache the port cmode") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-14net: dsa: mv88e6xxx: bitwise vs logical bugDan Carpenter1-2/+2
We are trying to test if these flags are set but there are some && vs & typos. Fixes: efd1ba6af93f ("net: dsa: mv88e6xxx: Add SERDES phydev_mac_change up for 6390") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-10net: dsa: rtl8366rb: Support port 4 (WAN)Linus Walleij1-0/+30
The totally undocumented IO mode needs to be set to enumerator 0 to enable port 4 also known as WAN in most configurations, for ordinary traffic. The 3 bits in the register come up as 010 after reset, but need to be set to 000. The Realtek source code contains a name for these bits, but no explanation of what the 8 different IO modes may be. Set it to zero for the time being and drop a comment so people know what is going on if they run into trouble. This "mode zero" works fine with the D-Link DIR-685 with RTL8366RB. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-25 13:28:34 +0300