| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250414200434.194422-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PTP_PEROUT_REQUEST2 ioctl has gained support for flags specifying
specific output behavior including PTP_PEROUT_ONE_SHOT,
PTP_PEROUT_DUTY_CYCLE, PTP_PEROUT_PHASE.
Driver authors are notorious for not checking the flags of the request.
This results in misinterpreting the request, generating an output signal
that does not match the requested value. It is anticipated that even more
flags will be added in the future, resulting in even more broken requests.
Expecting these issues to be caught during review or playing whack-a-mole
after the fact is not a great solution.
Instead, introduce the supported_perout_flags field in the ptp_clock_info
structure. Update the core character device logic to explicitly reject any
request which has a flag not on this list.
This ensures that drivers must 'opt in' to the flags they support. Drivers
which don't set the .supported_perout_flags field will not need to check
that unsupported flags aren't passed, as the core takes care of this.
Update the drivers which do support flags to set this new field.
Note the following driver files set n_per_out to a non-zero value but did
not check the flags at all:
• drivers/ptp/ptp_clockmatrix.c
• drivers/ptp/ptp_idt82p33.c
• drivers/ptp/ptp_fc3.c
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
• drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
• drivers/net/dsa/sja1105/sja1105_ptp.c
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/mscc/ocelot_vsc7514.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-2-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PTP_EXTTS_REQUEST(2) ioctl has a flags field which specifies how the
external timestamp request should behave. This includes which edge of the
signal to timestamp, as well as a specialized "offset" mode. It is expected
that more flags will be added in the future.
Driver authors routinely do not check the flags, often accepting requests
with flags which they do not support. Even drivers which do check flags may
not be future-proofed to reject flags not yet defined. Thus, any future
flag additions often require manually updating drivers to reject these
flags.
This approach of hoping we catch flag checks during review, or playing
whack-a-mole after the fact is the wrong approach.
Introduce the "supported_extts_flags" field to the ptp_clock_info
structure. This field defines the set of flags the device actually
supports.
Update the core character device logic to check this field and reject
unsupported requests. Getting this right is somewhat tricky. First, to
avoid unnecessary repetition and make basic functionality work when
.supported_extts_flags is 0, the core always accepts the PTP_ENABLE_FEATURE
flag. This flag is used to set the 'on' parameter to the .enable function
and is thus always 'supported' by all drivers.
For backwards compatibility, the PTP_RISING_EDGE and PTP_FALLING_EDGE flags
are merely "hints" when using the old PTP_EXTTS_REQUEST ioctl, and are not
expected to be enforced. If the user issues PTP_EXTTS_REQUEST2, the
PTP_STRICT_FLAGS flag is added which is supposed to inform the driver to
strictly validate the flags and reject unsupported requests. To handle
this, first check if the driver reports PTP_STRICT_FLAGS support. If it
does not, then always allow the PTP_RISING_EDGE and PTP_FALLING_EDGE flags.
This keeps backwards compatibility with the original PTP_EXTTS_REQUEST
ioctl where these flags are not guaranteed to be honored.
This way, drivers which do not set the supported_extts_flags will continue
to accept requests for the original PTP_EXTTS_REQUEST ioctl. The core will
automatically reject requests with new flags, and correctly reject requests
with PTP_STRICT_FLAGS, where the driver is supposed to strictly validate
the flags.
Update the various drivers, refactoring their validation logic into the
.supported_extts_flags field. For consistency and readability,
PTP_ENABLE_FEATURE is not set in the supported flags list, and
PTP_EXTTS_EDGES is expanded to PTP_RISING_EDGE | PTP_FALLING_EDGE in all
cases.
Note the following driver files set n_ext_ts to a non-zero value but did
not check flags at all:
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/freescale/enetc/enetc_ptp.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
• drivers/net/ethernet/marvell/octeontx2/nic/otx2_ptp.c
• drivers/net/ethernet/renesas/ravb_ptp.c
• drivers/net/ethernet/renesas/rtsn.c
• drivers/net/ethernet/renesas/rtsn.h
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/ti/cpts.h
• drivers/net/ethernet/ti/icssg/icss_iep.c
• drivers/net/ethernet/xscale/ptp_ixp46x.c
• drivers/net/phy/bcm-phy-ptp.c
• drivers/ptp/ptp_ocp.c
• drivers/ptp/ptp_pch.c
• drivers/ptp/ptp_qoriq.c
These drivers behavior does change slightly: they will now reject the
PTP_EXTTS_REQUEST2 ioctl, because they do not strictly validate their
flags. This also makes them no longer incorrectly accept PTP_EXT_OFFSET.
Also note that the renesas ravb driver does not support PTP_STRICT_FLAGS.
We could leave the .supported_extts_flags as 0, but I added the
PTP_RISING_EDGE | PTP_FALLING_EDGE since the driver previously manually
validated these flags. This is equivalent to 0 because the core will allow
these flags regardless unless PTP_STRICT_FLAGS is also set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-1-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was reported that the internally calculated counter might differ from
the real one from the Switch MIB. This can happen if the switch directly
forward packets between the ports or offload small packets like ARP
request. In such case, the kernel counter will desync compared to the
real one transmitted and received by the Switch.
To correctly provide the real info to the kernel, implement .get_stats64
that will directly read the current MIB counter from the switch
register.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-7-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For consistency with the other MIB counter, move also the remaining MIB
counter to define and update the custom MIB table.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-6-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drop custom handling of TX/RX packet stats and error MIB counter and handle
them in the standard .get_eth_mac_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-5-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drop custom handling of TX/RX pause frame MIB counter and handle
them in the standard .get_eth_ctrl_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-4-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drop custom handling of packet size and RX error MIB counter and handle
them in the standard .get_rmon_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-3-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In preparation for migration to use of standard MIB API, generalize the
read port stats logic to a dedicated function.
This will permit to manually provide the offset and size of the MIB
counter to directly access specific counter.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Implement Enhanced Transmission Selection scheduler (ETS) support for
KSZ88x3 devices, which support two fixed egress scheduling modes:
Strict Priority and Weighted Fair Queuing (WFQ).
Since the switch does not allow remapping priorities to queues or
adjusting weights, this implementation only supports enabling
strict priority mode. If strict mode is not explicitly requested,
the switch falls back to its default WFQ mode.
This patch introduces KSZ88x3-specific handlers for ETS add and
delete operations and uses TXQ Split Control registers to toggle
the WFQ enable bit per queue. Corresponding macros are also added
for register access.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250410124249.2728568-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The mv88e6xxx has an internal PPU that polls PHY state. If we want to
access the internal PHYs, we need to disable the PPU first. Because
that is a slow operation, a 10ms timer is used to re-enable it,
canceled with every access, so bulk operations effectively only
disable it once and re-enable it some 10ms after the last access.
If a PHY is accessed and then the mv88e6xxx module is removed before
the 10ms are up, the PPU re-enable ends up accessing a dangling pointer.
This especially affects probing during bootup. The MDIO bus and PHY
registration may succeed, but registration with the DSA framework
may fail later on (e.g. because the CPU port depends on another,
very slow device that isn't done probing yet, returning -EPROBE_DEFER).
In this case, probe() fails, but the MDIO subsystem may already have
accessed the MIDO bus or PHYs, arming the timer.
This is fixed as follows:
- If probe fails after mv88e6xxx_phy_init(), make sure we also call
mv88e6xxx_phy_destroy() before returning
- In mv88e6xxx_remove(), make sure we do the teardown in the correct
order, calling mv88e6xxx_phy_destroy() after unregistering the
switch device.
- In mv88e6xxx_phy_destroy(), destroy both the timer and the work item
that the timer might schedule, synchronously waiting in case one of
the callbacks already fired and destroying the timer first, before
waiting for the work item.
- Access to the PPU is guarded by a mutex, the worker acquires it
with a mutex_trylock(), not proceeding with the expensive shutdown
if that fails. We grab the mutex in mv88e6xxx_phy_destroy() to make
sure the slow PPU shutdown is already done or won't even enter, when
we wait for the work item.
Fixes: 2e5f032095ff ("dsa: add support for the Marvell 88E6131 switch chip")
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250401135705.92760-1-david.oberhollenzer@sigma-star.at
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes to prepare for the 6.15 net-next PR.
No conflicts, adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
919f9f497dbc ("eth: bnxt: fix out-of-range access of vnic_info array")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove KSZ88x3-specific priority and apptrust configuration logic that was
based on incorrect register access assumptions. Also fix the register
offset for KSZ8_REG_PORT_1_CTRL_0 to align with get_port_addr() logic.
The KSZ88x3 switch family uses a different register layout compared to
KSZ9477-compatible variants. Specifically, port control registers need
offset adjustment through get_port_addr(), and do not match the datasheet
values directly.
Commit a1ea57710c9d ("net: dsa: microchip: dcb: add special handling for
KSZ88X3 family") introduced quirks based on datasheet offsets, which do
not work with the driver's internal addressing model. As a result, these
quirks addressed the wrong ports and caused unstable behavior.
This patch removes all KSZ88x3-specific DCB quirks and corrects the port
control register offset, effectively restoring working and predictable
apptrust configuration.
Fixes: a1ea57710c9d ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250321141044.2128973-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sja1105_table_delete_entry()
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page.
Fixes: 6666cebc5e30 ("net: dsa: sja1105: Add support for VLAN operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is all that we can support timestamping, so we shouldn't accept
anything else. Also see sja1105_hwtstamp_get().
To avoid erroring out in an inconsistent state, operate on copies of
priv->hwts_rx_en and priv->hwts_tx_en, and write them back when nothing
else can fail anymore.
Fixes: a602afd200f5 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Port counters with no name (aka
sja1105_port_counters[__SJA1105_COUNTER_UNUSED]) are skipped when
reporting sja1105_get_sset_count(), but are not skipped during
sja1105_get_strings() and sja1105_get_ethtool_stats().
As a consequence, the first reported counter has an empty name and a
bogus value (reads from area 0, aka MAC, from offset 0, bits start:end
0:0). Also, the last counter (N_NOT_REACH on E/T, N_RX_BCAST on P/Q/R/S)
gets pushed out of the statistics counters that get shown.
Skip __SJA1105_COUNTER_UNUSED consistently, so that the bogus counter
with an empty name disappears, and in its place appears a valid counter.
Fixes: 039b167d68a3 ("net: dsa: sja1105: don't use burst SPI reads for port statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the workaround for erratum
3.3 RGMII timing may be out of spec when transmit delay is enabled
for the 6320 family, which says:
When transmit delay is enabled via Port register 1 bit 14 = 1, duty
cycle may be out of spec. Under very rare conditions this may cause
the attached device receive CRC errors.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.4.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-8-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix internal PHYs definition for the 6320 family, which has only 2
internal PHYs (on ports 3 and 4).
Fixes: bc3931557d1d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 6.6.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-7-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c050f5e91b47 ("net: dsa: mv88e6xxx: Fill in STU support for all
supported chips") introduced STU methods, but did not add them to the
6320 family. Fix it.
Fixes: c050f5e91b47 ("net: dsa: mv88e6xxx: Fill in STU support for all supported chips")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-6-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
did not add the .port_set_policy() method for the 6320 family. Fix it.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-5-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit f36456522168 ("net: dsa: mv88e6xxx: move PVT description in
info") did not enable PVT for 6321 switch. Fix it.
Fixes: f36456522168 ("net: dsa: mv88e6xxx: move PVT description in info")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-4-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The atu_move_port_mask for 6341 family (Topaz) is 0xf, not 0x1f. The
PortVec field is 8 bits wide, not 11 as in 6390 family. Fix this.
Fixes: e606ca36bbf2 ("net: dsa: mv88e6xxx: rework ATU Remove")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-3-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VTU registers of the 6320 family use the 6352 semantics, not 6185.
Fix it.
Fixes: b8fee9571063 ("net: dsa: mv88e6xxx: add VLAN Get Next support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.15.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-2-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9b4 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e45a ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e77 ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed414 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the custom IRQ chip handler and mask/unmask functions with
REGMAP_IRQ. This significantly simplifies the code and allows for the
removal of almost all interrupt-related functions from mt7530.c.
Tested on MT7988A built-in switch (MMIO) as well as MT7531AE IC (MDIO).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/221013c3530b61504599e285c341a993f6188f00.1740792674.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packet Processor Engine (PPE) module used for hw acceleration on EN7581
mac block, in order to properly parse packets, requires DSA untagged
packets on TX side and read DSA tag from DMA descriptor on RX side.
For this reason, enable RX Special Tag (SPTAG) for EN7581 SoC.
This is a preliminary patch to enable netfilter flowtable hw offloading
on EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make NET_DSA_REALTEK_RTL8366RB_LEDS a hidden symbol.
It seems very unlikely user would want to intentionally
disable it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250228004534.3428681-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc5).
Conflicts:
drivers/net/ethernet/cadence/macb_main.c
fa52f15c745c ("net: cadence: macb: Synchronize stats calculations")
75696dd0fd72 ("net: cadence: macb: Convert to get_stats64")
https://lore.kernel.org/20250224125848.68ee63e5@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/intel/ice/ice_sriov.c
79990cf5e7ad ("ice: Fix deinitializing VF in error path")
a203163274a4 ("ice: simplify VF MSI-X managing")
net/ipv4/tcp.c
18912c520674 ("tcp: devmem: don't write truncated dmabuf CMSGs to userspace")
297d389e9e5b ("net: prefix devmem specific helpers")
net/mptcp/subflow.c
8668860b0ad3 ("mptcp: reset when MPTCP opts are dropped after join")
c3349a22c200 ("mptcp: consolidate subflow cleanup")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d617005475 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM53101 is a ethernet switch, very similar to the BCM53115.
Enable support for it, in the existing b53 dsa driver.
Signed-off-by: Torben Nielsen <torben.nielsen@prevas.dk>
Signed-off-by: Claus Stovgaard <claus.stovgaard@prevas.dk>
Link: https://patch.msgid.link/20250217080503.1390282-1-claus.stovgaard@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert mt7530 to use phylink managed EEE. When enabling EEE, we set
both PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 irrespective of the speed,
and clear them both when disabling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1thR9q-003vXI-Cp@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the helper of_get_available_child_by_name() to simplify
sja1105_mdiobus_register().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify a5psw_probe() by using of_get_available_child_by_name().
While at it, move of_node_put(mdio) inside the if block to avoid code
duplication.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"This is slightly smaller than usual, with the most interesting work
being still around RTNL scope reduction.
Core:
- More core refactoring to reduce the RTNL lock contention, including
preparatory work for the per-network namespace RTNL lock, replacing
RTNL lock with a per device-one to protect NAPI-related net device
data and moving synchronize_net() calls outside such lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge
and more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter:
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on each
restart.
Protocols:
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets, to
avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel TLS
(for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API:
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W
implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling:
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec, to ease
maintenance and future development.
- Add YNL support for decoding the link types used in net self-tests,
allowing a single build to run both net and drivers/net.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues,
affecting both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station
mode support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync"
* tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1386 commits)
net/rose: prevent integer overflows in rose_setsockopt()
net: phylink: fix regression when binding a PHY
net: ethernet: ti: am65-cpsw: streamline TX queue creation and cleanup
net: ethernet: ti: am65-cpsw: streamline RX queue creation and cleanup
net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path
ipv6: Convert inet6_rtm_deladdr() to per-netns RTNL.
ipv6: Convert inet6_rtm_newaddr() to per-netns RTNL.
ipv6: Move lifetime validation to inet6_rtm_newaddr().
ipv6: Set cfg.ifa_flags before device lookup in inet6_rtm_newaddr().
ipv6: Pass dev to inet6_addr_add().
ipv6: Convert inet6_ioctl() to per-netns RTNL.
ipv6: Hold rtnl_net_lock() in addrconf_init() and addrconf_cleanup().
ipv6: Hold rtnl_net_lock() in addrconf_dad_work().
ipv6: Hold rtnl_net_lock() in addrconf_verify_work().
ipv6: Convert net.ipv6.conf.${DEV}.XXX sysctl to per-netns RTNL.
ipv6: Add __in6_dev_get_rtnl_net().
net: stmmac: Drop redundant skb_mark_for_recycle() for SKB frags
net: mii: Fix the Speed display when the network cable is not connected
sysctl net: Remove macro checks for CONFIG_SYSCTL
eth: bnxt: update header sizing defaults
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the linkage between the DSA user port ethtool_ops :: get_ts_info
and the implementation from the Ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
|
|
qca8k_get_mac_eee() is no longer called by the core DSA code. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllP-007UzF-Gk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx_get_mac_eee() is no longer called by the core DSA code.
Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllK-007Uz9-D7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mt753x_get_mac_eee() is no longer called by the core DSA code. Remove
it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/E1tUllF-007Uz3-95@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz_get_mac_eee() is no longer called by the core DSA code. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllA-007Uyx-4o@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
b53_get_mac_eee() is no longer called by the core DSA code. Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUll5-007Uyr-1U@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
