| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit a7920efdd86d8a0d74402dbc80ead03b023294ba ]
There is an off-by-one error in rtl8366rb_is_vlan_valid()
making VLANs 0..4094 valid while it should be 1..4095.
Fix it.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3dfe8dde093a07e82fa472c0f8c29a7f6a2006a5 ]
We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7e1301ed1881447d2a25f9c6423738c33cbca133 ]
The VLANs and PVIDs on the RTL8366 utilizes a "member
configuration" (MC) which is largely unexplained in the
code.
This set-up requires a special ordering: rtl8366_set_pvid()
must be called first, followed by rtl8366_set_vlan(),
else the MC will not be properly allocated. Relax this
by factoring out the code obtaining an MC and reuse
the helper in both rtl8366_set_pvid() and
rtl8366_set_vlan() so we remove this strict ordering
requirement.
In the process, add some better comments and debug prints
so people who read the code understand what is going on.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6641a2c42b0a307b7638d10e5d4b90debc61389d ]
The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid
VLANs tossed at it, especially VLAN0, something the hardware
and driver cannot handle. Check validity and bail out like
we do in the other callbacks.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8098bd69bc4e925070313b1b95d03510f4f24738 ]
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa86 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aa92d836d5c40a7e21e563a272ad177f1bfd44dd ]
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dba1e4660a87927bdc03c23e36fd2c81a16a7ab1 ]
state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.
Fixes: de143c0e274b ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b9e03cd08250c60409099c791e858157838d9eb ]
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd944dc24336922656a48f4608bfb41abdcdc4aa ]
The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.
It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).
Fixes: af199a1a9cb0 ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ddcaf1ebb5e4e99240f29d531ee69d4244fe416 ]
When removing a port from a VLAN we are just erasing the
member config for the VLAN, which is wrong: other ports
can be using it.
Just mask off the port and only zero out the rest of the
member config once ports using of the VLAN are removed
from it.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f272285f6abb9178d029375599626baf3d5f4e8a ]
Remove 1000baseT_Half to advertise correct hardware capability in
phylink_validate() callback function.
Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 774d977abfd024e6f73484544b9abe5a5cd62de7 ]
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 788abc6d9d278ed6fa1fa94db2098481a04152b7 ]
Alter the rtl8366_vlan_add() to call rtl8366_set_vlan()
inside the loop that goes over all VIDs since we now
properly support calling that function more than once.
Augment the loop to postincrement as this is more
intuitive.
The loop moved past the last VID but called
rtl8366_set_vlan() with the port number instead of
the VID, assuming a 1-to-1 correspondence between
ports and VIDs. This was also a bug.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 15ab7906cc9290afb006df1bb1074907fbcc7061 ]
The RTL8366 would not handle adding new members (ports) to
a VLAN: the code assumed that ->port_vlan_add() was only
called once for a single port. When intializing the
switch with .configure_vlan_while_not_filtering set to
true, the function is called numerous times for adding
all ports to VLAN1, which was something the code could
not handle.
Alter rtl8366_set_vlan() to just |= new members and
untagged flags to 4k and MC VLAN table entries alike.
This makes it possible to just add new ports to a
VLAN.
Put in some helpful debug code that can be used to find
any further bugs here.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f3c66a3c7b4e8b9f654b3c998e9674376a51b0f ]
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d65 only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d65 ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.
There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.
This patch addresses both issues.
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9893 3-Port Gigabit Ethernet Switch can be controlled via SPI,
I²C or MDIO (very limited and not supported by this driver). While there
is already a compatible entry for the SPI bus, it was missing for I²C.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105_gating_cfg_time_to_interval function does this, as per the
comments:
/* The gate entries contain absolute times in their e->interval field. Convert
* that to proper intervals (i.e. "0, 5, 10, 15" to "5, 5, 5, 5").
*/
To perform that task, it iterates over gating_cfg->entries, at each step
updating the interval of the _previous_ entry. So one interval remains
to be updated at the end of the loop: the last one (since it isn't
"prev" for anyone else).
But there was an erroneous check, that the last element's interval
should not be updated if it's also the only element. I'm not quite sure
why that check was there, but it's clearly incorrect, as a tc-gate
schedule with a single element would get an e->interval of zero,
regardless of the duration requested by the user. The switch wouldn't
even consider this configuration as valid: it will just drop all traffic
that matches the rule.
Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, tas_data->enabled would remain true even after deleting all
tc-gate rules from the switch ports, which would cause the
sja1105_tas_state_machine to get unnecessarily scheduled.
Also, if there were any errors which would prevent the hardware from
enabling the gating schedule, the sja1105_tas_state_machine would
continuously detect and print that, spamming the kernel log, even if the
rules were subsequently deleted.
The rules themselves are _not_ active, because sja1105_init_scheduling
does enough of a job to not install the gating schedule in the static
config. But the virtual link rules themselves are still present.
So call the functions that remove the tc-gate configuration from
priv->tas_data.gating_cfg, so that tas_data->enabled can be set to
false, and sja1105_tas_state_machine will stop from being scheduled.
Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently sja1105_compose_gating_subschedule is not prepared to be
called for the case where we want to recompute the global tc-gate
configuration after we've deleted those actions on a port.
After deleting the tc-gate actions on the last port, max_cycle_time
would become zero, and that would incorrectly prevent
sja1105_free_gating_config from getting called.
So move the freeing function above the check for the need to apply a new
configuration.
Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that sja1105_compose_gating_subschedule must also be called
from sja1105_vl_delete, to recalculate the overall tc-gate
configuration. Currently this is not possible without introducing a
forward declaration. So move the function at the top of the file, along
with its dependencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_find_node_by_name() will do an of_node_put() on the "from" argument.
With CONFIG_OF_DYNAMIC enabled which checks for device_node reference
counts, we would be getting a warning like this:
[ 6.347230] refcount_t: increment on 0; use-after-free.
[ 6.352498] WARNING: CPU: 3 PID: 77 at lib/refcount.c:156
refcount_inc_checked+0x38/0x44
[ 6.360601] Modules linked in:
[ 6.363661] CPU: 3 PID: 77 Comm: kworker/3:1 Tainted: G W
5.4.46-gb78b3e9956e6 #13
[ 6.372546] Hardware name: BCM97278SV (DT)
[ 6.376649] Workqueue: events deferred_probe_work_func
[ 6.381796] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 6.386595] pc : refcount_inc_checked+0x38/0x44
[ 6.391133] lr : refcount_inc_checked+0x38/0x44
...
[ 6.478791] Call trace:
[ 6.481243] refcount_inc_checked+0x38/0x44
[ 6.485433] kobject_get+0x3c/0x4c
[ 6.488840] of_node_get+0x24/0x34
[ 6.492247] of_irq_find_parent+0x3c/0xe0
[ 6.496263] of_irq_parse_one+0xe4/0x1d0
[ 6.500191] irq_of_parse_and_map+0x44/0x84
[ 6.504381] bcm_sf2_sw_probe+0x22c/0x844
[ 6.508397] platform_drv_probe+0x58/0xa8
[ 6.512413] really_probe+0x238/0x3fc
[ 6.516081] driver_probe_device+0x11c/0x12c
[ 6.520358] __device_attach_driver+0xa8/0x100
[ 6.524808] bus_for_each_drv+0xb4/0xd0
[ 6.528650] __device_attach+0xd0/0x164
[ 6.532493] device_initial_probe+0x24/0x30
[ 6.536682] bus_probe_device+0x38/0x98
[ 6.540524] deferred_probe_work_func+0xa8/0xd4
[ 6.545061] process_one_work+0x178/0x288
[ 6.549078] process_scheduled_works+0x44/0x48
[ 6.553529] worker_thread+0x218/0x270
[ 6.557285] kthread+0xdc/0xe4
[ 6.560344] ret_from_fork+0x10/0x18
[ 6.563925] ---[ end trace 68f65caf69bb152a ]---
Fix this by adding a of_node_get() to increment the reference count
prior to the call.
Fixes: afa3b592953b ("net: dsa: bcm_sf2: Ensure correct sub-node is parsed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: dfacc5a23e22 ("net: dsa: sja1105: support flow-based redirection via virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This shouldn't be there.
Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It isn't actually described clearly at all in UM10944.pdf, but on TX of
a management frame (such as PTP), this needs to happen:
- The destination MAC address (i.e. 01-80-c2-00-00-0e), along with the
desired destination port, need to be installed in one of the 4
management slots of the switch, over SPI.
- The host can poll over SPI for that management slot's ENFPORT field.
That gets unset when the switch has matched the slot to the frame.
And therein lies the problem. ENFPORT does not mean that the packet has
been transmitted. Just that it has been received over the CPU port, and
that the mgmt slot is yet again available.
This is relevant because of what we are doing in sja1105_ptp_txtstamp_skb,
which is called right after sja1105_mgmt_xmit. We are in a hard
real-time deadline, since the hardware only gives us 24 bits of TX
timestamp, so we need to read the full PTP clock to reconstruct it.
Because we're in a hurry (in an attempt to make sure that we have a full
64-bit PTP time which is as close as possible to the actual transmission
time of the frame, to avoid 24-bit wraparounds), first we read the PTP
clock, then we poll for the TX timestamp to become available.
But of course, we don't know for sure that the frame has been
transmitted when we read the full PTP clock. We had assumed that ENFPORT
means it has, but the assumption is incorrect. And while in most
real-life scenarios this has never been caught due to software delays,
nowhere is this fact more obvious than with a tc-taprio offload, where
PTP traffic gets a small timeslot very rarely (example: 1 packet per 10
ms). In that case, we will be reading the PTP clock for timestamp
reconstruction too early (before the packet has been transmitted), and
this renders the reconstruction procedure incorrect (see the assumptions
described in the comments found on function sja1105_tstamp_reconstruct).
So the PTP TX timestamps will be off by 1<<24 clock ticks, or 135 ms
(1 tick is 8 ns).
So fix this case of premature optimization by simply reordering the
sja1105_ptpegr_ts_poll and the sja1105_ptpclkval_read function calls. It
turns out that in practice, the 135 ms hard deadline for PTP timestamp
wraparound is not so hard, since even the most bandwidth-intensive PTP
profiles, such as 802.1AS-2011, have a sync frame interval of 125 ms.
So if we couldn't deliver a timestamp in 135 ms (which we can), we're
toast and have much bigger problems anyway.
Fixes: 47ed985e97f5 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
While trying to use the lantiq_gswip driver on one of my boards I made
a mistake when specifying the phy-mode (because the out-of-tree driver
wants phy-mode "gmii" or "mii" for the internal PHYs). In this case the
following error is printed multiple times:
Unsupported interface: 3
While it gives at least a hint at what may be wrong it is not very user
friendly. Print the human readable phy-mode and also which port is
configured incorrectly (this hardware supports ports 0..6) to improve
the cases where someone made a mistake.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
replaced the dsa_switch_alloc helper by devm_kzalloc in all DSA
drivers. Unfortunately it introduced a typo in qca8k.c driver and
wrong argument is passed to the devm_kzalloc function.
This fix mitigates the following kernel exception:
Unexpected gfp: 0x6 (__GFP_HIGHMEM|GFP_DMA32). Fixing up to gfp: 0x101 (GFP_DMA|__GFP_ZERO). Fix your code!
CPU: 1 PID: 44 Comm: kworker/1:1 Not tainted 5.5.9-yocto-ua #1
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: events deferred_probe_work_func
[<c0014924>] (unwind_backtrace) from [<c00123bc>] (show_stack+0x10/0x14)
[<c00123bc>] (show_stack) from [<c04c8fb4>] (dump_stack+0x90/0xa4)
[<c04c8fb4>] (dump_stack) from [<c00e1b10>] (new_slab+0x20c/0x214)
[<c00e1b10>] (new_slab) from [<c00e1cd0>] (___slab_alloc.constprop.0+0x1b8/0x540)
[<c00e1cd0>] (___slab_alloc.constprop.0) from [<c00e2074>] (__slab_alloc.constprop.0+0x1c/0x24)
[<c00e2074>] (__slab_alloc.constprop.0) from [<c00e4538>] (__kmalloc_track_caller+0x1b0/0x298)
[<c00e4538>] (__kmalloc_track_caller) from [<c02cccac>] (devm_kmalloc+0x24/0x70)
[<c02cccac>] (devm_kmalloc) from [<c030d888>] (qca8k_sw_probe+0x94/0x1ac)
[<c030d888>] (qca8k_sw_probe) from [<c0304788>] (mdio_probe+0x30/0x54)
[<c0304788>] (mdio_probe) from [<c02c93bc>] (really_probe+0x1e0/0x348)
[<c02c93bc>] (really_probe) from [<c02c9884>] (driver_probe_device+0x60/0x16c)
[<c02c9884>] (driver_probe_device) from [<c02c7fb0>] (bus_for_each_drv+0x70/0x94)
[<c02c7fb0>] (bus_for_each_drv) from [<c02c9708>] (__device_attach+0xb4/0x11c)
[<c02c9708>] (__device_attach) from [<c02c8148>] (bus_probe_device+0x84/0x8c)
[<c02c8148>] (bus_probe_device) from [<c02c8cec>] (deferred_probe_work_func+0x64/0x90)
[<c02c8cec>] (deferred_probe_work_func) from [<c0033c14>] (process_one_work+0x1d4/0x41c)
[<c0033c14>] (process_one_work) from [<c00340a4>] (worker_thread+0x248/0x528)
[<c00340a4>] (worker_thread) from [<c0039148>] (kthread+0x124/0x150)
[<c0039148>] (kthread) from [<c00090d8>] (ret_from_fork+0x14/0x3c)
Exception stack(0xee1b5fb0 to 0xee1b5ff8)
5fa0: 00000000 00000000 00000000 00000000
5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
qca8k 2188000.ethernet-1:0a: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
qca8k 2188000.ethernet-1:0a eth2 (uninitialized): PHY [2188000.ethernet-1:01] driver [Generic PHY]
qca8k 2188000.ethernet-1:0a eth1 (uninitialized): PHY [2188000.ethernet-1:02] driver [Generic PHY]
Fixes: 7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dynamic configuration interface for the General Params and the L2
Lookup Params tables was copy-pasted between E/T devices and P/Q/R/S
devices. Nonetheless, these interfaces are bitwise different.
The driver is using dynamic reconfiguration of the General Parameters
table for the port mirroring feature, which was therefore broken on
P/Q/R/S.
Note that this patch can't be backported easily very far to stable trees
(since it conflicts with some other development done since the
introduction of the driver). So the Fixes: tag is purely informational.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer compilers complain with W=1 builds that there are non-static
functions defined in sja1105_static_config.c that don't have a
prototype, because their prototype is defined in sja1105.h which this
translation unit does not include.
I don't entirely understand what is the point of these warnings, since
in principle there's nothing wrong with that. But let's move the
prototypes to a header file that _is_ included by
sja1105_static_config.c, since that will make these warnings go away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup,
both under the same VLAN-filtering bridge, both in the
SJA1105_VLAN_BEST_EFFORT state.
If we try to change the VLAN state of one of the switches (to
SJA1105_VLAN_FILTERING_FULL) we get the following error:
devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value
false cmode runtime
[ 38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory.
L2 memory partitions and VL memory partitions share the
same space. The sum of all 16 memory partitions is not
allowed to be larger than 929 128-byte blocks (or 910
with retagging). Please adjust
l2-forwarding-parameters-table.part_spc and/or
vl-forwarding-parameters-table.partspc.
[ 38.356803] sja1105 spi2.1: Invalid config, cannot upload
This is because the spi/spi2.1 switch doesn't support tagging anymore in
the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any
retagging rules defined. Great, so it can use more frame memory
(retagging consumes extra memory).
But the built-in low-level static config checker from the sja1105 driver
says "not so fast, you've increased the frame memory to non-retagging
values, but you still kept the retagging rules in the static config".
So we need to rebuild the VLAN table immediately before re-uploading the
static config, operation which will take care, based on the new VLAN
state, of removing the retagging rules.
Fixes: 3f01c91aab92 ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SJA1105, being AVB/TSN switches, provide hardware assist for the
Credit-Based Shaper as described in the IEEE 8021Q-2018 document.
First generation has 10 shapers, freely assignable to any of the 4
external ports and 8 traffic classes, and second generation has 16
shapers.
The Credit-Based Shaper tables are accessed through the dynamic
reconfiguration interface, so we have to restore them manually after a
switch reset. The tables are backed up by the static config only on
P/Q/R/S, and we don't want to add custom code only for that family,
since the procedure that is in place now works for both.
Tested with the following commands:
data_rate_kbps=67000
port_transmit_rate_kbps=1000000
idleslope=$data_rate_kbps
sendslope=$(($idleslope - $port_transmit_rate_kbps))
locredit=$((-0x80000000))
hicredit=$((0x7fffffff))
tc qdisc add dev swp2 root handle 1: mqprio hw 0 num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7
tc qdisc replace dev swp2 parent 1:1 cbs \
idleslope $idleslope \
sendslope $sendslope \
hicredit $hicredit \
locredit $locredit \
offload 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in other commits before (b9cd75e66895 and 87b0f983f66f),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.
But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:
bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16
(note that port 5 is the CPU port and not the front-panel swp0).
So this hardware will send all VLANs as tagged towards the CPU.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow DSA to add VLAN entries even if VLAN filtering is disabled, so
enabling it will not block the traffic of existent ports in the bridge
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d18 ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot VSC9959 switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. This patch add support for TAS configuration
on egress port of VSC9959 switch.
Felix driver is an instance of Ocelot family, with a DSA front-end. The
patch uses tc taprio hardware offload to setup TAS set function on felix
driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
