| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.
Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This partially reverts ed8fe20205ac ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
DSA framework
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205ac ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYs
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d1d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_set_duplex
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51e8 ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 787799a9d555 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.
This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).
This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.
Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.
Fix this by using the source port ID for the violation, which really
is a port number.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Tested-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 65f60e4582bd ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b91 ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move .port_set_cmode next to .port_get_cmode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c5005 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
