summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand/raw/brcmnand
AgeCommit message (Collapse)AuthorFilesLines
2022-09-21mtd: rawnand: brcmnand: Add individual glue driver selectionFlorian Fainelli2-4/+32
Allow each platform to define a dedicated Kconfig entry for its glue driver such that we can decide on a per-platfomr basis whether to build it or not. This allows for a finer grained control over the resulting kernel image or set of modules. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-3-f.fainelli@gmail.com
2022-09-21mtd: rawnand: brcmnand: Move Kconfig to driver folderFlorian Fainelli1-0/+21
In preparation for allowing each of the brcmnand stub to be built separately, move the Kconfig entry to the driver folder. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-2-f.fainelli@gmail.com
2022-03-23Merge tag 'nand/for-5.18' into mtd/nextMiquel Raynal4-52/+271
Raw NAND core changes: * Rework of_get_nand_bus_width() * Remove of_get_nand_on_flash_bbt() wrapper * Protect access to rawnand devices while in suspend * bindings: Document the wp-gpios property Rax NAND controller driver changes: * atmel: Fix refcount issue in atmel_nand_controller_init * nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc * rockchip: Fix platform_get_irq.cocci warning * stm32_fmc2: Add NAND Write Protect support * pl353: Set the nand chip node as the flash node * brcmnand: Fix sparse warnings in bcma_nand * omap_elm: Remove redundant variable 'errors' * gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting * brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: * Check for error irq Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-03-18Merge tag 'spi-nor/for-5.18' into mtd/nextMiquel Raynal1-1/+1
SPI NOR core changes: - move vendor specific code out of the core into vendor drivers. - unify all function and object names in the vendor modules. - make setup() callback optional to improve readability. - skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-01-31mtd: rawnand: Fix misuses of of_match_node()Miquel Raynal1-1/+1
On non-OF enabled platforms (CONFIG_OF is not set), of_match_node() will expand to NULL. The of_device_id array pointed by the macro will then be left unused. Let's mark the array __maybe_unused in this case to prevent compiler warnings. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/linux-mtd/20220127110802.1064963-1-miquel.raynal@bootlin.com
2022-01-31mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC statusdavid regan1-1/+1
The brcmnand driver contains a bug in which if a page (example 2k byte) is read from the parallel/ONFI NAND and within that page a subpage (512 byte) has correctable errors which is followed by a subpage with uncorrectable errors, the page read will return the wrong status of correctable (as opposed to the actual status of uncorrectable.) The bug is in function brcmnand_read_by_pio where there is a check for uncorrectable bits which will be preempted if a previous status for correctable bits is detected. The fix is to stop checking for bad bits only if we already have a bad bits status. Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by: david regan <dregan@mail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
2022-01-26mtd: rawnand: brcmnand: Fix sparse warnings in bcma_nandFlorian Fainelli1-2/+2
sparse was unhappy about the way we woulc call cpu_to_be32/be32_to_cpu, apply the appropriate casting to silence the warnings. Reported-by: kernel test robot <lkp@intel.com> Link: https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/ZNHPJFYLO64EGI5QUT7HZ63J7O5J2G7N/ Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220125225243.15201-1-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Add BCMA shimFlorian Fainelli3-0/+138
Add a BCMA shim to allow us to register the brcmnand driver using the BCMA bus which provides indirect memory mapped access to SoC registers. There are a number of registers that need to be byte swapped because they are natively big endian, coming directly from the NAND chip, and there is no bus interface unlike the iProc or STB platforms that performs the byte swapping for us. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-10-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: BCMA controller uses command shift of 0Florian Fainelli1-0/+6
For some odd and unexplained reason the BCMA NAND controller, albeit revision 3.4 uses a command shift of 0 instead of 24 as it should be, quirk that. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-9-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Allow platform data instantationFlorian Fainelli1-10/+35
Make use of the recently refactored code in brcmnand_init_cs() and derive the chip-select from the platform data that is supplied. Update the various code paths to avoid relying on possibly non-existent resources, too. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-8-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Allow working without interruptsFlorian Fainelli1-28/+24
The BCMA devices include the brcmnand controller but they do not wire up any interrupt line, allow the main interrupt to be optional and update the completion path to also check for the lack of an interrupt line. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-6-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Move OF operations out of brcmnand_init_cs()Florian Fainelli1-9/+11
In order to initialize a given chip select object for use by the brcmnand driver, move all of the Device Tree specific routines outside of brcmnand_init_cs() in order to make it usable in a platform data configuration which will be necessary for supporting BCMA chips. No functional changes introduced. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-5-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Avoid pdev in brcmnand_init_cs()Florian Fainelli1-4/+4
In preparation for encapsulating more of what the loop calling brcmnand_init_cs() does, avoid using platform_device when it is the device behind platform_device that we are using for printing errors. No functional changes introduced. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-4-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Allow SoC to provide I/O operationsFlorian Fainelli2-2/+55
Allow a brcmnand_soc instance to provide a custom set of I/O operations which we will require when using this driver on a BCMA bus which is not directly memory mapped I/O. Update the nand_{read,write}_reg accordingly to use the SoC operations if provided. To minimize the penalty on other SoCs which do support standard MMIO accesses, we use a static key which is disabled by default and gets enabled if a soc implementation does provide I/O operations. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-3-f.fainelli@gmail.com
2022-01-23mtd: rawnand: brcmnand: Assign soc as early as possibleFlorian Fainelli1-2/+1
In order to key off the brcmnand_probe() code in subsequent changes depending upon ctrl->soc, assign that variable as early as possible, instead of much later when we have checked that it is non-NULL. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-2-f.fainelli@gmail.com
2021-09-14mtd: rawnand: bcm6368: Make use of the helper function ↵Cai Huoqing1-4/+1
devm_platform_ioremap_resource_byname() Use the devm_platform_ioremap_resource_byname() helper instead of calling platform_get_resource_byname() and devm_ioremap_resource() separately Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210901074108.8933-1-caihuoqing@baidu.com
2021-03-28mtd: rawnand: brcmnand: move to polling in pio mode on oops writeKamal Dasu1-0/+4
This change makes sure that Broadcom NAND driver moves to interrupt polling on the first brcmnand_write() call. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210311170909.9031-2-kdasu.kdev@gmail.com
2021-03-28mtd: rawnand: brcmnand: read/write oob during EDU transferKamal Dasu1-7/+52
Added support to read/write oob during EDU transfers. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210311170909.9031-1-kdasu.kdev@gmail.com
2021-03-11mtd: rawnand: brcmnand: fix OOB R/W with Hamming ECCÁlvaro Fernández Rojas1-0/+6
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall always be done without ECC enabled. This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2 clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed from ff ff ff to 00 00 00, reporting incorrect ECC errors. Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
2020-11-20mtd: rawnand: brcmnand: Demote non-conformant kernel-doc headersLee Jones1-3/+3
Fixes the following W=1 kernel build warning(s): drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'host' not described in 'brcmnand_edu_trans' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'addr' not described in 'brcmnand_edu_trans' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'buf' not described in 'brcmnand_edu_trans' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'len' not described in 'brcmnand_edu_trans' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'cmd' not described in 'brcmnand_edu_trans' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'host' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'desc' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'addr' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'buf' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'len' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'dma_cmd' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'begin' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'end' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'next_desc' not described in 'brcmnand_fill_dma_desc' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'host' not described in 'brcmnand_dma_run' drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'desc' not described in 'brcmnand_dma_run' Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kamal Dasu <kdasu.kdev@gmail.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: linux-mtd@lists.infradead.org Cc: bcm-kernel-feedback-list@broadcom.com Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-14-lee.jones@linaro.org
2020-09-28mtd: rawnand: Use nanddev_get/set_ecc_requirements() when relevantMiquel Raynal1-3/+5
Instead of accessing ->strength/step_size directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-15-miquel.raynal@bootlin.com
2020-09-28mtd: rawnand: Use the new ECC engine type enumerationMiquel Raynal1-4/+4
Mechanical switch from the legacy "mode" enumeration to the new "engine type" enumeration in drivers and board files. The device tree parsing is also updated to return the new enumeration from the old strings. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
2020-08-27mtd: rawnand: Rename the ECC algorithm enumeration itemsMiquel Raynal1-6/+6
NAND_ECC_ is not a meaningful prefix, use NAND_ECC_ALGO_ instead. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-3-miquel.raynal@bootlin.com
2020-06-26mtd: rawnand: brcmnand: ECC error handling on EDU transfersKamal Dasu1-0/+26
Implement ECC correctable and uncorrectable error handling for EDU reads. If ECC correctable bitflips are encountered on EDU transfer, read page again using PIO. This is needed due to a NAND controller limitation where corrected data is not transferred to the DMA buffer on ECC error. This applies to ECC correctable errors that are reported by the controller hardware based on set number of bitflips threshold in the controller threshold register, bitflips below the threshold are corrected silently and are not reported by the controller hardware. Fixes: a5d53ad26a8b ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-3-kdasu.kdev@gmail.com
2020-06-26mtd: rawnand: brcmnand: Don't default to edu transferKamal Dasu1-2/+3
When flash-dma is absent do not default to using flash-edu. Make sure flash-edu is enabled before setting EDU transfer function. Fixes: a5d53ad26a8b ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-2-kdasu.kdev@gmail.com
2020-06-01Merge tag 'nand/for-5.8' of ↵Richard Weinberger1-44/+120
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next Raw NAND core changes: * Stop using nand_release(), patched all drivers. * Give more information about the ECC weakness when not matching the chip's requirement. * MAINTAINERS updates. * Support emulated SLC mode on MLC NANDs. * Support "constrained" controllers, adapt the core and ONFI/JEDEC table parsing and Micron's code. * Take check_only into account. * Add an invalid ECC mode to discriminate with valid ones. * Return an enum from of_get_nand_ecc_algo(). * Drop OOB_FIRST placement scheme. * Introduce nand_extract_bits(). * Ensure a consistent bitflips numbering. * BCH lib: - Allow easy bit swapping. - Rework a little bit the exported function names. * Fix nand_gpio_waitrdy(). * Propage CS selection to sub operations. * Add a NAND_NO_BBM_QUIRK flag. * Give the possibility to verify a read operation is supported. * Add a helper to check supported operations. * Avoid indirect access to ->data_buf(). * Rename the use_bufpoi variables. * Fix comments about the use of bufpoi. * Rename a NAND chip option. * Reorder the nand_chip->options flags. * Translate obscure bitfields into readable macros. * Timings: - Fix default values. - Add mode information to the timings structure. Raw NAND controller driver changes: * Fixed many error paths. * Arasan - New driver * Au1550nd: - Various cleanups - Migration to ->exec_op() * brcmnand: - Misc cleanup. - Support v2.1-v2.2 controllers. - Remove unused including <linux/version.h>. - Correctly verify erased pages. - Fix Hamming OOB layout. * Cadence - Make cadence_nand_attach_chip static. * Cafe: - Set the NAND_NO_BBM_QUIRK flag * cmx270: - Remove this controller driver. * cs553x: - Misc cleanup - Migration to ->exec_op() * Davinci: - Misc cleanup. - Migration to ->exec_op() * Denali: - Add more delays before latching incoming data * Diskonchip: - Misc cleanup - Migration to ->exec_op() * Fsmc: - Change to non-atomic bit operations. * GPMI: - Use nand_extract_bits() - Fix runtime PM imbalance. * Ingenic: - Migration to exec_op() - Fix the RB gpio active-high property on qi, lb60 - Make qi_lb60_ooblayout_ops static. * Marvell: - Misc cleanup and small fixes * Nandsim: - Fix the error paths, driver wide. * Omap_elm: - Fix runtime PM imbalance. * STM32_FMC2: - Misc cleanups (error cases, comments, timeout valus, cosmetic changes).
2020-05-31mtd: rawnand: brcmnand: support v2.1-v2.2 controllersÁlvaro Fernández Rojas1-9/+76
v2.1: tested on Netgear DGND3700v1 (BCM6368) v2.2: tested on Netgear DGND3700v2 (BCM6362) Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-6-noltari@gmail.com
2020-05-31mtd: rawnand: brcmnand: rename page sizesÁlvaro Fernández Rojas1-2/+2
Current pages sizes apply to controllers after v3.4 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-4-noltari@gmail.com
2020-05-31mtd: rawnand: brcmnand: fix CS0 layoutÁlvaro Fernández Rojas1-2/+3
Only v3.3-v5.0 have a different CS0 layout. Controllers before v3.3 use the same layout for every CS. Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
2020-05-31mtd: rawnand: brcmnand: rename v4 registersÁlvaro Fernández Rojas1-4/+4
These registers are also used on v3.3. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-2-noltari@gmail.com
2020-05-31mtd: rawnand: brcmnand: Stop using nand_release()Miquel Raynal1-2/+8
This helper is not very useful and very often people get confused: they use nand_release() instead of nand_cleanup(). Let's stop using nand_release() by calling mtd_device_unregister() and nand_cleanup() directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kamal Dasu <kdasu.kdev@gmail.com> Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-5-miquel.raynal@bootlin.com
2020-05-24mtd: rawnand: brcmnand: correctly verify erased pagesÁlvaro Fernández Rojas1-8/+11
The current code checks that the whole OOB area is erased. This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will fail due to the usable OOB bytes not being 0xff. Correct this by only checking that data and ECC bytes aren't 0xff. Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
2020-05-24mtd: rawnand: brcmnand: improve hamming oob layoutÁlvaro Fernández Rojas1-19/+16
The current code generates 8 oob sections: S1 1-5 ECC 6-8 S2 9-15 S3 16-21 ECC 22-24 S4 25-31 S5 32-37 ECC 38-40 S6 41-47 S7 48-53 ECC 54-56 S8 57-63 Change it by merging continuous sections: S1 1-5 ECC 6-8 S2 9-21 ECC 22-24 S3 25-37 ECC 38-40 S4 41-53 ECC 54-56 S5 57-63 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200512075733.745374-3-noltari@gmail.com
2020-05-24mtd: rawnand: brcmnand: fix hamming oob layoutÁlvaro Fernández Rojas1-4/+7
First 2 bytes are used in large-page nand. Fixes: ef5eeea6e911 ("mtd: nand: brcm: switch to mtd_ooblayout_ops") Cc: stable@vger.kernel.org Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200512075733.745374-2-noltari@gmail.com
2020-05-19mtd:rawnand: brcmnand: Fix PM resume crashKamal Dasu1-2/+1
This change fixes crash observed on PM resume. This bug was introduced in the change made for flash-edu support. Fixes: a5d53ad26a8b ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2020-05-11mtd: rawnand: Rename a NAND chip optionMiquel Raynal1-1/+1
NAND controller drivers can set the NAND_USE_BOUNCE_BUFFER flag to a chip 'option' field. With this flag, the core is responsible of providing DMA-able buffers. The current behavior is to not force the use of a bounce buffer when the core thinks this is not needed. So in the end the name is a bit misleading, because in theory we will always have a DMA buffer but in practice it will not always be a bounce buffer. Rename this flag NAND_USES_DMA to be more accurate. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-4-miquel.raynal@bootlin.com
2020-05-10mtd: rawnand: brcmnand: Remove unused including <linux/version.h>YueHaibing1-1/+0
Remove including <linux/version.h> that don't need it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200417101129.35556-1-yuehaibing@huawei.com
2020-03-11mtd: rawnand: brcmnand: Add support for flash-edu for dma transfersKamal Dasu1-6/+287
Legacy mips soc platforms that have controller v5.0 and 6.0 use flash-edu block for dma transfers. This change adds support for nand dma transfers using the EDU block. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-4-kdasu.kdev@gmail.com
2020-01-21mtd: rawnand: brcmnand: Set appropriate DMA maskFlorian Fainelli1-0/+10
NAND controllers >= 7.0 with FLASH_DMA support physical addresses up to 40-bit, set an appropriate DMA mask for that purpose. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-10-29mtd: rawnand: brcmnand: Fix NULL pointer assignmentFlorian Fainelli1-1/+1
Sparse complained about the following: drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer fix this issue by assigning the pointer to NULL. Fixes: c1ac2dc34b51 ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-10-04mtd: nand: brcmnand: Add support for flash-dma v0Kamal Dasu1-2/+19
This change adds support for flash dma v0.0. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-08-29mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page bitfipsClaire Lin1-1/+4
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation while correcting erased page bitflips is wrong, fix it. Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips") Signed-off-by: Claire Lin <claire.lin@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: rawnand: brcmnand: Add support for v7.3 controllerKamal Dasu1-22/+80
This change adds support for brcm NAND v7.3 controller. This controller uses a newer version of flash_dma engine and change mostly implements these differences. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: rawnand: brcmnand: Refactored code to introduce helper functionsKamal Dasu1-38/+62
Refactored NAND ECC and CMD address configuration code to use helper functions. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: rawnand: brcmnand: When oops in progress use pio and interrupt pollingKamal Dasu1-3/+45
If mtd_oops is in progress, switch to polling during NAND command completion instead of relying on DMA/interrupts so that the mtd_oops buffer can be completely written in the assigned NAND partition. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: rawnand: brcmnand: fallback to detected ecc-strength, ecc-step-sizeKamal Dasu1-0/+11
This change supports nand-ecc-step-size and nand-ecc-strength fields in brcmnand DT node to be optional. see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt If both nand-ecc-strength and nand-ecc-step-size are not specified in device tree node for NAND, raw NAND layer does detect ECC information by reading ONFI extended parameter page for parts using ONFI >= 2.1. In case of non-ONFI NAND parts there could be a nand_id table entry with ECC information. If there is valid device tree entry for nand-ecc-strength and nand-ecc-step-size fields it still shall override the detected values. Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-06-27mtd: rawnand: brcmnand: Fix BCH ECC layout for large page NAND partsKamal Dasu1-1/+1
The way oobregion->offset is derived for large page NAND parts is wrong, fixes it. Fixes: ef5eeea6e911 ("mtd: nand: brcm: switch to mtd_ooblayout_ops") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174Thomas Gleixner6-54/+6
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 655 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-08mtd: rawnand: Provide a helper to get chip->data_bufBoris Brezillon1-5/+2
We plan to move cache related fields to a pagecache struct in nand_chip but some drivers access ->pagebuf directly to invalidate the cache before they start using ->data_buf. Let's provide an helper that returns a pointer to ->data_buf after invalidating the cache. Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2018-10-03mtd: rawnand: Deprecate ->dev_ready() and ->waitfunc()Boris Brezillon1-1/+1
Those hooks have been replaced by ->exec_op(). Move them to the nand_legacy struct. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-19 16:36:38 +0300