summaryrefslogtreecommitdiff
path: root/drivers/mtd/devices
AgeCommit message (Collapse)AuthorFilesLines
2020-01-23mtd: devices: fix mchp23k256 read and writeAngelo Dureghello1-8/+12
commit 14f89e088155314d311e4d4dd9f2b4ccaeef92b2 upstream. Due to the use of sizeof(), command size set for the spi transfer was wrong. Driver was sending and receiving always 1 byte less and especially on write, it was hanging. echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1 And read part too now works as expected. hexdump -C -n16 /dev/mtd1 00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15 00000010 Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17mtd: spear_smi: Fix Write Burst modeMiquel Raynal1-1/+37
commit 69c7f4618c16b4678f8a4949b6bb5ace259c0033 upstream. Any write with either dd or flashcp to a device driven by the spear_smi.c driver will pass through the spear_smi_cpy_toio() function. This function will get called for chunks of up to 256 bytes. If the amount of data is smaller, we may have a problem if the data length is not 4-byte aligned. In this situation, the kernel panics during the memcpy: # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6 spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256 spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256 spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256 spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233 Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8 [...] PC is at memcpy+0xcc/0x330 The above error occurs because the implementation of memcpy_toio() tries to optimize the number of I/O by writing 4 bytes at a time as much as possible, until there are less than 4 bytes left and then switches to word or byte writes. Unfortunately, the specification states about the Write Burst mode: "the next AHB Write request should point to the next incremented address and should have the same size (byte, half-word or word)" This means ARM architecture implementation of memcpy_toio() cannot reliably be used blindly here. Workaround this situation by update the write path to stick to byte access when the burst length is not multiple of 4. Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash") Cc: Russell King <linux@armlinux.org.uk> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-24mtd: devices: m25p80: Make sure WRITE_EN is issued before each writeYogesh Gaur1-15/+8
[ Upstream commit 3baa8ec88c2feb902328e59a4dcf0f0aaab7d2ff ] Some SPI controllers can't write nor->page_size bytes in a single step because their TX FIFO is too small, but when that happens we should make sure a WRITE_EN command before each write access and READ_SR command after each write access is issued. The core is already taking care of that, so all we have to do here is return the actual number of bytes that were written during the spi_mem_exec_op() operation. Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2018-11-21mtd: docg3: don't set conflicting BCH_CONST_PARAMS optionArnd Bergmann1-1/+1
commit be2e1c9dcf76886a83fb1c433a316e26d4ca2550 upstream. I noticed during the creation of another bugfix that the BCH_CONST_PARAMS option that is set by DOCG3 breaks setting variable parameters for any other users of the BCH library code. The only other user we have today is the MTD_NAND software BCH implementation (most flash controllers use hardware BCH these days and are not affected). I considered removing BCH_CONST_PARAMS entirely because of the inherent conflict, but according to the description in lib/bch.c there is a significant performance benefit in keeping it. To avoid the immediate problem of the conflict between MTD_NAND_BCH and DOCG3, this only sets the constant parameters if MTD_NAND_BCH is disabled, which should fix the problem for all cases that are affected. This should also work for all stable kernels. Note that there is only one machine that actually seems to use the DOCG3 driver (arch/arm/mach-pxa/mioa701.c), so most users should have the driver disabled, but it almost certainly shows up if we wanted to test random kernels on machines that use software BCH in MTD. Fixes: d13d19ece39f ("mtd: docg3: add ECC correction code") Cc: stable@vger.kernel.org Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18mtd: devices: m25p80: Make sure the buffer passed in op is DMA-ableBoris Brezillon1-3/+23
As documented in spi-mem.h, spi_mem_op->data.buf.{in,out} must be DMA-able, and commit 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API") failed to follow this rule as buffers passed to ->{read,write}_reg() are usually placed on the stack. Fix that by allocating a scratch buffer and copying the data around. Fixes: 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API") Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
2018-08-14Merge tag 'spi-v4.19' of ↵Linus Torvalds1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "Quite an active release for the SPI subsystem, lots of small updates and fixes scattered about with highlights including: - 3-wire support in the GPIO driver. - support for setting a custom memory name in the memory mapped flash drivers. - support for extended mode in the Freescale DSPI controller. - support for the non-standard integration with the Microsemi Ocelot platform in the DesignWare driver. - new driver for the SocioNext UniPhier" * tag 'spi-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (47 commits) spi: davinci: fix a NULL pointer dereference spi: spi-mem: Constify spi_mem->name mtd: m25p80: Call spi_mem_get_name() to let controller set a custom name spi: spi-mem: Extend the SPI mem interface to set a custom memory name spi: spi-mem: Fix a typo in the documentation of struct spi_mem spi: uniphier: remove unnecessary include headers spi: spi-gpio: add SPI_3WIRE support spi: add flags parameter to txrx_word function pointers spi: add SPI controller driver for UniPhier SoC spi: add DT bindings for UniPhier SPI controller spi: dw: document Microsemi integration spi: img-spfi: Set device select bits for SPFI port state spi: omap2-mcspi: remove several redundant variables spi: dw-mmio: add MSCC Ocelot support spi: dw: export dw_spi_set_cs spi: spi-fsl-espi: Log fifo counters on error spi: imx: Use the longuest possible burst size when in dynamic_burst spi: imx: remove unnecessary check in spi_imx_can_dma spi: imx: Use correct number of bytes per words spi: imx: Use dynamic bursts only when bits_per_word is 8, 16 or 32 ...
2018-08-11Merge tag 'spi-nor/for-4.19' of git://git.infradead.org/linux-mtd into mtd/nextBoris Brezillon1-4/+1
Pull SPI NOR updates from Boris Brezillon: " Core changes: - Apply reset hacks only when reset is explicitly marked as broken in the DT Driver changes: - Minor cleanup/fixes in the m25p80 driver - Release flash_np in the nxp-spifi driver - Add suspend/resume hooks to the atmel-quadspi driver - Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver - Use %pK instead of %p in the stm32-quadspi driver - Improve timeout handling in the cadence-quadspi driver - Use mtd_device_register() instead of mtd_device_parse_register() in the intel-spi driver "
2018-08-11Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/nextBoris Brezillon1-2/+2
Pull NAND updates from Miquel Raynal: " NAND core changes: - Add the SPI-NAND framework. - Create a helper to find the best ECC configuration. - Create NAND controller operations. - Allocate dynamically ONFI parameters structure. - Add defines for ONFI version bits. - Add manufacturer fixup for ONFI parameter page. - Add an option to specify NAND chip as a boot device. - Add Reed-Solomon error correction algorithm. - Better name for the controller structure. - Remove unused caller_is_module() definition. - Make subop helpers return unsigned values. - Expose _notsupp() helpers for raw page accessors. - Add default values for dynamic timings. - Kill the chip->scan_bbt() hook. - Rename nand_default_bbt() into nand_create_bbt(). - Start to clean the nand_chip structure. - Remove stale prototype from rawnand.h. Raw NAND controllers drivers changes: - Qcom: structuring cleanup. - Denali: use core helper to find the best ECC configuration. - Possible build of almost all drivers by adding a dependency on COMPILE_TEST for almost all of them in Kconfig, implies various fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even changes in sparc64 and ia64 architectures. - Clean the ->probe() functions error path of a lot of drivers. - Migrate all drivers to use nand_scan() instead of nand_scan_ident()/nand_scan_tail() pair. - Use mtd_device_register() where applicable to simplify the code. - Marvell: * Handle on-die ECC. * Better clocks handling. * Remove bogus comment. * Add suspend and resume support. - Tegra: add NAND controller driver. - Atmel: * Add module param to avoid using dma. * Drop Wenyou Yang from MAINTAINERS. - Denali: optimize timings handling. - FSMC: Stop using chip->read_buf(). - FSL: * Switch to SPDX license tag identifiers. * Fix qualifiers in MXC init functions. Raw NAND chip drivers changes: - Micron: * Add fixup for ONFI revision. * Update ecc_stats.corrected. * Make ECC activation stateful. * Avoid enabling/disabling ECC when it can't be disabled. * Get the actual number of bitflips. * Allow forced on-die ECC. * Support 8/512 on-die ECC. * Fix on-die ECC detection logic. - Hynix: * Fix decoding the OOB size on H27UCG8T2BTR. * Use ->exec_op() in hynix_nand_reg_write_op(). "
2018-08-10Merge branch 'spi-4.19' into spi-nextMark Brown1-0/+3
2018-08-02mtd: m25p80: Call spi_mem_get_name() to let controller set a custom nameFrieder Schrempf1-0/+3
By calling spi_mem_get_name(), the driver of the (Q)SPI controller can set a custom name for the memory device if necessary. This is useful to keep mtdparts compatible when controller drivers are ported from the MTD to the SPI layer. Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-07-20mtd: Make Kconfig formatting consistentBoris Brezillon1-2/+2
Fix indentation and replace '---help---' by 'help' to make things consistent. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-18mtd: sst25l: use mtd_device_register()Rafał Miłecki1-3/+2
This driver doesn't specify parsers so it can use that little helper. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-07-18mtd: powernv_flash: set of_node in mtd's devRafał Miłecki1-0/+1
This enables some features implemented in mtd subsystem like reading label and partitioning info from DT. Reported-by: Timothy Pearson <tpearson@raptorengineering.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-22mtd: dataflash: Use ULL suffix for 64-bit constantsGeert Uytterhoeven1-2/+2
With gcc 4.1.2 when compiling for 32-bit: drivers/mtd/devices/mtd_dataflash.c:736: warning: integer constant is too large for ‘long’ type drivers/mtd/devices/mtd_dataflash.c:737: warning: integer constant is too large for ‘long’ type Add the missing "ULL" suffixes to fix this. Fixes: 67e4145ebf2c161d ("mtd: dataflash: Add flash_info for AT45DB641E") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-06-18mtd: m25p80: Use SPI_MEM_OP_NO_DUMMY instead of SPI_MEM_OP_DUMMY(0, x)Boris Brezillon1-2/+1
SPI_MEM_OP_DUMMY(0, x) means there's 0 dummy bytes to send, which is similar to SPI_MEM_OP_NO_DUMMY except it's less clear. Use SPI_MEM_OP_NO_DUMMY instead of SPI_MEM_OP_DUMMY(0, x) in m25p80_write(). Also stop updating op.dummy.buswidth since this value is only meaningful if you have dummy bytes. Reported-by: Cyrille Pitchen <cyrille.pitchen@microchip.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2018-06-18mtd: m25p80: Remove unneeded m25p->command fieldBoris Brezillon1-2/+0
The ->command field is no longer used, remove it. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2018-06-13treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook1-1/+1
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-13treewide: kzalloc() -> kcalloc()Kees Cook1-1/+1
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-08Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtdLinus Torvalds2-3/+2
Pull MTD updates from Boris Brezillon: "Core changes: - Add a sysfs attribute to expose available OOB size Driver changes: - Remove HAS_DMA dependency on various drivers - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3 - Replace msleep by usleep_range() in the dataflash driver - Avoid VLA usage in nftl layers - Remove useless .owner assignment in pismo - Fix various issues in the CFI driver - Improve TRX partition handling expose a DT compat for this part parser - Clarify OFFSET_CONTINUOUS meaning NAND core changes: - Add Miquel as a NAND maintainer - Add access mode to the nand_page_io_req struct - Fix kernel-doc in rawnand.h - Support bit-wise majority to recover from corrupted ONFI parameter pages - Stop checking FAIL bit after a SET_FEATURES, as documented in the ONFI spec Raw NAND Driver changes: - Fix and cleanup the error path of many NAND controller drivers - GPMI: + Cleanup/simplification of a few aspects in the driver + Take ECC setup specified in the DT into account - sunxi: remove support for GPIO-based R/B polling - MTK: + Use of_device_get_match_data() instead of of_match_device() + Add an entry in MAINTAINERS for this driver + Fix nand-ecc-step-size and nand-ecc-strength description in the DT bindings doc - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page OneNAND driver changes: - samsung: use dev_get_drvdata() instead of platform_get_drvdata() SPI NOR core changes: - Add support for a bunch of SPI NOR chips - Clear EAR reg when switching to 3-byte addressing mode on Winbond chips SPI NOR controller driver changes: - cadence: Add DMA support for direct mode reads - hisi: Prefix a few functions with hisi_ - intel: + Mark the driver as "dangerous" in Kconfig + Fix atomic sequence handling + Pass a 40us delay (instead of 0us) to readl_poll_timeout() - fsl: + fix a typo in a function name + add support for IP variants embedded in the ls2080a and ls1080a SoCs - stm32: request exclusive control of the reset line" * tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits) mtd: nand: Pass mode information to nand_page_io_req mtd: cfi_cmdset_0002: Change erase one block to enable XIP once mtd: cfi_cmdset_0002: Change erase functions to check chip good only mtd: cfi_cmdset_0002: Change erase functions to retry for error mtd: cfi_cmdset_0002: Change definition naming to retry write operation mtd: cfi_cmdset_0002: Change write buffer to check correct value mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS mtd: bcm47xxpart: add of_match_table with a new DT binding dt-bindings: mtd: document Broadcom's BCM47xx partitions mtd: spi-nor: Add support for EN25QH32 mtd: spi-nor: Add support for is25wp series chips mtd: spi-nor: Add Winbond w25q32jv support mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control mtd: spi-nor: intel: provide a range for poll_timout mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig mtd: spi-nor: intel-spi: Fix atomic sequence handling mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op mtd: rawnand: use bit-wise majority to recover the ONFI param page ...
2018-05-22mtd: devices: m25p80: Use spi_mem_set_drvdata() instead of spi_set_drvdata()Boris Brezillon1-1/+1
SPI mem drivers should use spi_mem_set_drvdata() not spi_set_drvdata() to store their private data. Using spi_set_drvdata() will mess the spi -> spi-mem link up and cause a kernel panic at shutdown or device removal time. Fixes: 4120f8d158ef ("mtd: spi-nor: Use the spi_mem_xx() API") Reported-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com> on R8A7791 Porter Signed-off-by: Mark Brown <broonie@kernel.org>
2018-05-11mtd: spi-nor: Use the spi_mem_xx() APIBoris Brezillon2-157/+80
The spi_mem_xxx() API has been introduced to replace the spi_flash_read() one. Make use of it so we can get rid of spi_flash_read(). Note that using spi_mem_xx() also simplifies the code because this API takes care of using the regular spi_sync() interface when the optimized ->mem_ops interface is not implemented by the controller. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de> Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-22mtd: dataflash: replace msleep with usleep_rangeLuca Ellero1-1/+1
Since msleep is based on jiffies, this 3 ms sleep becomes actually 20 ms. Worst of all, since this sleep is used in a loop when writing, a single page write (256 to 1024 bytes) causes 17 ms extra time. When writing large files (for example u-boot is usually 512 KB) this delay adds up to minutes. See Documentation/timers/timers-howto.txt "Why not msleep for (1ms - 20ms)". Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-04-22mtd: devices: simplify getting .drvdataWolfram Sang1-2/+1
We should get drvdata from struct device directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-21mtd: Stop updating erase_info->state and calling mtd_erase_callback()Boris Brezillon13-75/+8
MTD users are no longer checking erase_info->state to determine if the erase operation failed or succeeded. Moreover, mtd_erase_callback() is now a NOP. We can safely get rid of all mtd_erase_callback() calls and all erase_info->state assignments. While at it, get rid of the erase_info->state field, all MTD_ERASE_XXX definitions and the mtd_erase_callback() function. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Richard Weinberger <richard@nod.at> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Bert Kenward <bkenward@solarflare.com> --- Changes in v2: - Address a few coding style issues (reported by Miquel) - Remove comments that are no longer valid (reported by Miquel)
2018-03-15mtd: Stop assuming mtd_erase() is asynchronousBoris Brezillon1-3/+0
None of the mtd->_erase() implementations work in an asynchronous manner, so let's simplify MTD users that call mtd_erase(). All they need to do is check the value returned by mtd_erase() and assume that != 0 means failure. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Richard Weinberger <richard@nod.at>
2018-03-15mtd: st_spi_fsm: use %*ph to print small bufferAntonio Cardace1-2/+1
Use %*ph format to print small buffer as hex string. Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Antonio Cardace <anto.cardace@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15mtd: block2mtd: remove redundant initialization of 'bdev'Colin Ian King1-1/+1
Pointer bdev is being initialized however this value is never read as bdev is assigned an updated value from the returned call to blkdev_get_by_path. Remove the redundant assignment. Cleans up clang warning: drivers/mtd/devices/block2mtd.c:228:23: warning: Value stored to 'bdev' during its initialization is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-01-29Merge tag 'spi-nor/for-4.16' of git://git.infradead.org/linux-mtd into mtd/nextBoris Brezillon1-0/+9
Pull spi-nor changes from Cyrille Pitchen: " This pull-request contains the following notable changes: Core changes: * Add support to new ISSI and Cypress/Spansion memory parts. * Fix support of Micron memories by checking error bits in the FSR. * Fix update of block-protection bits by reading back the SR. * Restore the internal state of the SPI flash memory when removing the device. Driver changes: * Maintenance for Freescale, Intel and Metiatek drivers. * Add support of the direct access mode for the Cadence QSPI controller. "
2018-01-16mtd: Remove duplicate checks on mtd_oob_ops parameterBoris Brezillon1-5/+0
Some of the check done in custom ->_read/write_oob() implementation are already done by the core (in mtd_check_oob_ops()). Suggested-by: Peter Pan <peterpansjtu@gmail.com> [Remove redundant checks done in mtdpart.c] Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
2018-01-16mtd: Fallback to ->_read/write_oob() when ->_read/write() is missingBoris Brezillon1-65/+0
Some MTD sublayers/drivers are implementing ->_read/write_oob() and provide dummy wrappers for their ->_read/write() implementations. Let the core handle this case instead of duplicating the logic. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
2017-12-17mtd: mchp23k256: propagate return value of spi_sync()Antonio Borneo1-4/+14
The call to spi_sync() can fail. Check the return value and propagate it. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-13mtd: m25p80: restore the status of SPI flash when exitingHou Zhiqiang1-0/+9
Restore the status to be compatible with legacy devices. Take Freescale eSPI boot for example, it copies (in 3 Byte addressing mode) the RCW and bootloader images from SPI flash without firing a reset signal previously, so the reboot command will fail without resetting the addressing mode of SPI flash. This patch implements .shutdown function to restore the status in reboot process, and add the same operation to the .remove function. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-11-23Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtdLinus Torvalds5-20/+35
Pull MTD updates from Richard Weinberger: "General changes: - Unconfuse get_unmapped_area and point/unpoint driver methods - New partition parser: sharpslpart - Kill GENERIC_IO - Various fixes NAND changes: - Add a flag to mark NANDs that require 3 address cycles to encode a page address - Set a default ECC/free layout when NAND_ECC_NONE is requested - Fix a bug in panic_nand_write() - Another batch of cleanups for the denali driver - Fix PM support in the atmel driver - Remove support for platform data in the omap driver - Fix subpage write in the omap driver - Fix irq handling in the mtk driver - Change link order of mtk_ecc and mtk_nand drivers to speed up boot time - Change log level of ECC error messages in the mxc driver - Patch the pxa3xx driver to support Armada 8k platforms - Add BAM DMA support to the qcom driver - Convert gpio-nand to the GPIO desc API - Fix ECC handling in the mt29f driver SPI-NOR changes: - Introduce system power management support - New mechanism to select the proper .quad_enable() hook by JEDEC ID, when needed, instead of only by manufacturer ID - Add support to new memory parts from Gigadevice, Winbond, Macronix and Everspin - Maintainance for Cadence, Intel, Mediatek and STM32 drivers" * tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits) mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid mtd: sharpslpart: Add sharpslpart partition parser mtd: Add sanity checks in mtd_write/read_oob() mtd: remove the get_unmapped_area method mtd: implement mtd_get_unmapped_area() using the point method mtd: chips/map_rom.c: implement point and unpoint methods mtd: chips/map_ram.c: implement point and unpoint methods mtd: mtdram: properly handle the phys argument in the point method mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD' mtd: slram: use memremap() instead of ioremap() kconfig: kill off GENERIC_IO option mtd: Fix C++ comment in include/linux/mtd/mtd.h mtd: constify mtd_partition mtd: plat-ram: Replace manual resource management by devm mtd: nand: Fix writing mtdoops to nand flash. mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID mtd: nand: mtk: fix infinite ECC decode IRQ issue mtd: spi-nor: Add support for mr25h128 mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o mtd: spi-nor: enable 4B opcodes for mx66l51235l ...
2017-11-16Merge tag 'powerpc-4.15-1' of ↵Linus Torvalds1-30/+53
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: "A bit of a small release, I suspect in part due to me travelling for KS. But my backlog of patches to review is smaller than usual, so I think in part folks just didn't send as much this cycle. Non-highlights: - Five fixes for the >128T address space handling, both to fix bugs in our implementation and to bring the semantics exactly into line with x86. Highlights: - Support for a new OPAL call on bare metal machines which gives us a true NMI (ie. is not masked by MSR[EE]=0) for debugging etc. - Support for Power9 DD2 in the CXL driver. - Improvements to machine check handling so that uncorrectable errors can be reported into the generic memory_failure() machinery. - Some fixes and improvements for VPHN, which is used under PowerVM to notify the Linux partition of topology changes. - Plumbing to enable TM (transactional memory) without suspend on some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND). - Support for emulating vector loads form cache-inhibited memory, on some Power9 revisions. - Disable the fast-endian switch "syscall" by default (behind a CONFIG), we believe it has never had any users. - A major rework of the API drivers use when initiating and waiting for long running operations performed by OPAL firmware, and changes to the powernv_flash driver to use the new API. - Several fixes for the handling of FP/VMX/VSX while processes are using transactional memory. - Optimisations of TLB range flushes when using the radix MMU on Power9. - Improvements to the VAS facility used to access coprocessors on Power9, and related improvements to the way the NX crypto driver handles requests. - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit. Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A. Kennington III" * tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits) powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature powerpc/64s: Fix masking of SRR1 bits on instruction fault powerpc/64s: mm_context.addr_limit is only used on hash powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary powerpc/64s/hash: Fix fork() with 512TB process address space powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation powerpc/64s/hash: Fix 512T hint detection to use >= 128T powerpc: Fix DABR match on hash based systems powerpc/signal: Properly handle return value from uprobe_deny_signal() powerpc/fadump: use kstrtoint to handle sysfs store powerpc/lib: Implement UACCESS_FLUSHCACHE API powerpc/lib: Implement PMEM API powerpc/powernv/npu: Don't explicitly flush nmmu tlb powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm() powerpc/powernv/idle: Round up latency and residency values powerpc/kprobes: refactor kprobe_lookup_name for safer string operations powerpc/kprobes: Blacklist emulate_update_regs() from kprobes powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace powerpc/kprobes: Disable preemption before invoking probe handler for optprobes ...
2017-11-16Merge tag 'modules-for-v4.15' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux Pull module updates from Jessica Yu: "Summary of modules changes for the 4.15 merge window: - treewide module_param_call() cleanup, fix up set/get function prototype mismatches, from Kees Cook - minor code cleanups" * tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux: module: Do not paper over type mismatches in module_param_call() treewide: Fix function prototypes for module_param_call() module: Prepare to convert all module_param_call() prototypes kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
2017-11-14mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalidBoris Brezillon1-1/+6
Commit e8e3edb95ce6 ("mtd: create per-device and module-scope debugfs entries") tried to make MTD related debugfs stuff consistent across the MTD framework by creating a root <debugfs>/mtd/ directory containing one directory per MTD device. The problem is that, by default, the MTD layer only registers the master device if no partitions are defined for this master. This behavior breaks all drivers that expect mtd->dbg.dfs_dir to be filled correctly after calling mtd_device_register() in order to add their own debugfs entries. The only way we can force all MTD masters to be registered no matter if they expose partitions or not is by enabling the CONFIG_MTD_PARTITIONED_MASTER option. In such situations, there's no other solution but to accept skipping debugfs initialization when dbg.dfs_dir is invalid, and when this happens, inform the user that he should consider enabling CONFIG_MTD_PARTITIONED_MASTER. Fixes: e8e3edb95ce6 ("mtd: create per-device and module-scope debugfs entries") Cc: <stable@vger.kernel.org> Cc: Mario J. Rugiero <mrugiero@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reported-by: Richard Weinberger <richard@nod.at> Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13mtd: remove the get_unmapped_area methodNicolas Pitre1-14/+0
It is now unused. Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13mtd: mtdram: properly handle the phys argument in the point methodNicolas Pitre1-0/+22
When the phys pointer is non null, the point method is expected to return the physical address for the pointed area. In the case of the mtdram driver we have to retrieve the physical address for the corresponding vmalloc area. However, there is no guarantee that the vmalloc area is made of physically contiguous pages. In that case we simply limit retlen to the actually contiguous pages. Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13mtd: slram: use memremap() instead of ioremap()Roy Franz1-4/+5
Convert slram to use memremap() to map the memory it uses to back an MTD device, as this is the proper interface for mapping memory. This change enables normal memory to be used to back an MTD device on arm64, as arm64 prevents ioremap() being used on normal memory. Signed-off-by: Roy Franz <roy.franz@cavium.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Tested-by: David Daney <david.daney@cavium.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-07mtd: constify mtd_partitionArvind Yadav1-1/+1
mtd_partition are not supposed to change at runtime. Functions 'mtd_device_parse_register' working with const mtd_partition provided by <linux/mtd/mtd.h>. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-06mtd: powernv_flash: Use opal_async_wait_response_interruptible()Cyril Bur1-22/+35
The OPAL calls performed in this driver shouldn't be using opal_async_wait_response() as this performs a wait_event() which, on long running OPAL calls could result in hung task warnings. wait_event() prevents timely signal delivery which is also undesirable. This patch also attempts to quieten down the use of dev_err() when errors haven't actually occurred and also to return better information up the stack rather than always -EIO. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06mtd: powernv_flash: Don't return -ERESTARTSYS on interrupted token acquisitionCyril Bur1-0/+7
Because the MTD core might split up a read() or write() from userspace into several calls to the driver, we may fail to get a token but already have done some work, best to return -EINTR back to userspace and have them decide what to do. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06mtd: powernv_flash: Remove pointless goto in driver initCyril Bur1-10/+6
powernv_flash_probe() has pointless goto statements which jump to the end of the function to simply return a variable. Rather than checking for error and going to the label, just return the error as soon as it is detected. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06mtd: powernv_flash: Don't treat OPAL_SUCCESS as an errorCyril Bur1-5/+10
While this driver expects to interact asynchronously, OPAL is well within its rights to return OPAL_SUCCESS to indicate that the operation completed without the need for a callback. We shouldn't treat OPAL_SUCCESS as an error rather we should wrap up and return promptly to the caller. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06mtd: powernv_flash: Use WARN_ON_ONCE() rather than BUG_ON()Cyril Bur1-1/+3
BUG_ON() should be reserved in situations where we can not longer guarantee the integrity of the system. In the case where powernv_flash_async_op() receives an impossible op, we can still guarantee the integrity of the system. Signed-off-by: Cyril Bur <cyrilbur@gmail.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2-0/+2
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-31treewide: Fix function prototypes for module_param_call()Kees Cook2-2/+2
Several function prototypes for the set/get functions defined by module_param_call() have a slightly wrong argument types. This fixes those in an effort to clean up the calls when running under type-enforced compiler instrumentation for CFI. This is the result of running the following semantic patch: @match_module_param_call_function@ declarer name module_param_call; identifier _name, _set_func, _get_func; expression _arg, _mode; @@ module_param_call(_name, _set_func, _get_func, _arg, _mode); @fix_set_prototype depends on match_module_param_call_function@ identifier match_module_param_call_function._set_func; identifier _val, _param; type _val_type, _param_type; @@ int _set_func( -_val_type _val +const char * _val , -_param_type _param +const struct kernel_param * _param ) { ... } @fix_get_prototype depends on match_module_param_call_function@ identifier match_module_param_call_function._get_func; identifier _val, _param; type _val_type, _param_type; @@ int _get_func( -_val_type _val +char * _val , -_param_type _param +const struct kernel_param * _param ) { ... } Two additional by-hand changes are included for places where the above Coccinelle script didn't notice them: drivers/platform/x86/thinkpad_acpi.c fs/lockd/svc.c Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jessica Yu <jeyu@kernel.org>
2017-10-29mtd: spi-nor: Add support for mr25h128Philipp Puschmann1-0/+1
Add Everspin mr25h128 16KB MRAM to the list of supported chips. Signed-off-by: Philipp Puschmann <pp@emlix.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-09-01Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/nextBoris Brezillon1-8/+12
From Boris: " This pull request contains the following core changes: * Fix memory leaks in the core * Remove unused NAND locking support * Rename nand.h into rawnand.h (preparing support for spi NANDs) * Use NAND_MAX_ID_LEN where appropriate * Fix support for 20nm Hynix chips * Fix support for Samsung and Hynix SLC NANDs and the following driver changes: * Various cleanup, improvements and fixes in the qcom driver * Fixes for bugs detected by various static code analysis tools * Fix mxc ooblayout definition * Add a new part_parsers to tmio and sharpsl platform data in order to define a custom list of partition parsers * Request the reset line in exclusive mode in the sunxi driver * Fix a build error in the orion-nand driver when compiled for ARMv4 * Allow 64-bit mvebu platforms to select the PXA3XX driver "
2017-08-23mtd: st_spi_fsm: Handle clk_prepare_enable/clk_disable_unprepare.Arvind Yadav1-8/+12
- clk_prepare_enable() can fail here and we must check its return value. - stfsm_probe() can fail here and we must disable clock. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-26 12:25:32 +0300