| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 222cfa0118aa68687ace74aab8fdf77ce8fbd7e6 upstream.
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before amd_probe() returns. There is no problem for the 'smbus_dev ==
NULL' branch because pci_dev_put() can also handle the NULL input
parameter case.
Fixes: 659c9bc114a8 ("mmc: sdhci-pci: Build o2micro support in the same module")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221114083100.149200-1-wangxiongfeng2@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
timeout
commit 096cc0cddf58232bded309336961784f1d1c85f8 upstream.
The SD card is recognized failed sometimes when resume from suspend.
Because CD# debounce time too long then card present report wrong.
Finally, card is recognized failed.
Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221104095512.4068-1-chevron.li@bayhubtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39a72dbfe188291b156dd6523511e3d5761ce775 upstream.
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
Fixes: ce69d37b7d8f ("mmc: core: Prevent violation of specs while initializing cards")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb1dec44c6750bb414f47b929c8c175a1a127c31 upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: bb6e358169bf ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.4.I7d01f9ad11bacdc9213dee61b7918982aea39115@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f002f45a00ee14214d96b18b9a555fe2c56afb20 upstream.
MMC_CAP_8_BIT_DATA belongs to struct mmc_host, not struct sdhci_host.
So correct it here.
Fixes: 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1667893503-20583-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 836078449464e6af3b66ae6652dae79af176f21e upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 3c4019f97978 ("mmc: tegra: HW Command Queue Support for Tegra SDMMC")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.5.I418c9eaaf754880fcd2698113e8c3ef821a944d7@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 162503fd1c3a1d4e14dbe7f399c1d1bec1c8abbc upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: f545702b74f9 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.6.I35ca9d6220ba48304438b992a76647ca8e5b126f@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56baa208f91061ff27ec2d93fbc483f624d373b4 upstream.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
I only patch the bcm7216 variant even though others potentially *could*
provide the 'supports-cqe' property (and thus enable CQHCI), because
d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing
(CQE)") and some Broadcom folks confirm that only the 7216 variant
actually supports it.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.3.I6a715feab6d01f760455865e968ecf0d85036018@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d249ac37fc2396e8acc1adb0650cdacae5a990d upstream.
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but one
particular case I hit commonly enough: mmc_suspend() -> mmc_power_off().
Typically we will eventually deactivate CQE (cqhci_suspend() ->
cqhci_deactivate()), but that's not guaranteed -- in particular, if
we perform a partial (e.g., interrupted) system suspend.
The same bug was already found and fixed for two other drivers, in v5.7
and v5.9:
5cf583f1fb9c ("mmc: sdhci-msm: Deactivate CQE during SDHC reset")
df57d73276b8 ("mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel
GLK-based controllers")
The latter is especially prescient, saying "other drivers using CQHCI
might benefit from a similar change, if they also have CQHCI reset by
SDHCI_RESET_ALL."
So like these other patches, deactivate CQHCI when resetting the
controller. Do this via the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221026124150.v4.2.I29f6a2189e84e35ad89c1833793dca9e36c64297@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebb5fd38f41132e6924cb33b647337f4a5d5360c upstream.
Several SDHCI drivers need to deactivate command queueing in their reset
hook (see sdhci_cqhci_reset() / sdhci-pci-core.c, for example), and
several more are coming.
Those reset implementations have some small subtleties (e.g., ordering
of initialization of SDHCI vs. CQHCI might leave us resetting with a
NULL ->cqe_private), and are often identical across different host
drivers.
We also don't want to force a dependency between SDHCI and CQHCI, or
vice versa; non-SDHCI drivers use CQHCI, and SDHCI drivers might support
command queueing through some other means.
So, implement a small helper, to avoid repeating the same mistakes in
different drivers. Simply stick it in a header, because it's so small it
doesn't deserve its own module right now, and inlining to each driver is
pretty reasonable.
This is marked for -stable, as it is an important prerequisite patch for
several SDHCI controller bugfixes that follow.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221026124150.v4.1.Ie85faa09432bfe1b0890d8c24ff95e17f3097317@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ed5c3b22fc78735c539e4767832aea58db6761c upstream.
The core issues the warning "drop HS400 support since no 8-bit bus" when
one of the ESDHC_FLAG_HS400* flags is set on a non 8bit capable host. To
avoid this warning set these flags only on hosts that actually can do
8bit, i.e. have bus-width = <8> set in the device tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 029e2476f9e6 ("mmc: sdhci-esdhc-imx: add HS400_ES support for i.MX8QXP")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221013093248.2220802-1-s.hauer@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9dc0033e4658d6f9d9952c3c0c6be3ec25bc2985 upstream.
Enhanced Strobe (ES) does not work correctly on the ASUS 1100 series of
devices. Jasper Lake eMMCs (pci_id 8086:4dc4) are supposed to support
ES. There are also two system families under the series, thus this is
being scoped to the ASUS BIOS.
The failing ES prevents the installer from writing to disk. Falling back
to HS400 without ES fixes the issue.
Signed-off-by: Patrick Thompson <ptf@google.com>
Fixes: 315e3bd7ac19 ("mmc: sdhci-pci: Add support for Intel JSL")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221013210017.3751025-1-ptf@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 028822b714bd3a159d65416c53f1549345b53d9e upstream.
WRITE_ZEROES requests use TRIM, so mark them as needing to be issued
synchronously even when a CQE is being used. Without this,
mmc_blk_mq_issue_rq() triggers a WARN_ON_ONCE() and fails the request
since we don't have any handling for issuing this asynchronously.
Fixes: f7b6fc327327 ("mmc: core: Support zeroout using TRIM for eMMC")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221020130123.4033218-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9972e6b404884adae9eec7463e30d9b3c9a70b18 upstream.
SDIO tuple is only allocated for standard SDIO card, especially it causes
memory corruption issues when the non-standard SDIO card has removed, which
is because the card device's reference counter does not increase for it at
sdio_init_func(), but all SDIO card device reference counter gets decreased
at sdio_release_func().
Fixes: 6f51be3d37df ("sdio: allow non-standard SDIO cards")
Signed-off-by: Matthew Ma <mahongwei@zeku.com>
Reviewed-by: Weizhao Ouyang <ouyangweizhao@zeku.com>
Reviewed-by: John Wang <wangdayu@zeku.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221014034951.2300386-1-ouyangweizhao@zeku.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 339e3eb1facd18a98ceb1171d70674780e5014a7 upstream.
To prevent any recovery work running after the queue cleanup cancel it.
Any recovery running post-cleanup dereferenced mq->card as NULL
and was not meaningful to begin with.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/c865c0c9789d428494b67b820a78923e@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 406e14808ee695cbae1eafa5fd3ac563c29470ab upstream.
Before switching back to the right partition in mmc_blk_reset there used
to be a check if hw_reset was even supported. This return value
was removed, so there is no reason to check. Furthermore ensure
part_curr is not falsely set to a valid value on reset or
partition switch error.
As part of this change the code paths of mmc_blk_reset calls were checked
to ensure no commands are issued after a failed mmc_blk_reset directly
without going through the block layer.
Fixes: fefdd3c91e0a ("mmc: core: Drop superfluous validations in mmc_hw|sw_reset()")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/e91be6199d04414a91e20611c81bfe1d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d280b1df87e0b3d1355aeac7e62b62214b93f1c upstream.
REGMAP_MMIO is not user-configurable, so we can only satisfy this
dependency by enabling some other Kconfig symbol that properly 'select's
it. Use select like everybody else.
Noticed when trying to enable this driver for compile testing.
Fixes: 59592cc1f593 ("mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221024180300.2292208-1-briannorris@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4de95950d970c71a9e82a24573bb7a44fd95baa1 ]
The Snapdragon 670 has the same quirk as Snapdragon 845 (needing to
restore the dll config). Add a compatible string check to detect the need
for this.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220923014322.33620-3-mailingradian@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cb58188ad90a61784a56a64f5107faaf2ad323e7 ]
A dma_free_coherent() call is missing in the error handling path of the
probe, as already done in the remove function.
Fixes: 3a96dff0f828 ("mmc: SD/MMC Host Controller for Wondermedia WM8505/WM8650")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/53fc6ffa5d1c428fefeae7d313cf4a669c3a1e98.1663873255.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5cbedf52608cc3cbc1c2a9a861fb671620427a20 ]
If clk_prepare_enable() fails, there is no point in calling
clk_disable_unprepare() in the error handling path.
Move the out_clk label at the right place.
Fixes: b6507596dfd6 ("MIPS: Alchemy: au1xmmc: use clk framework")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/21d99886d07fa7fcbec74992657dabad98c935c4.1661412818.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6e141772e6465f937458b35ddcfd0a981b6f5280 upstream.
The Spreadtrum controller supports 100KHz minimal clock rate, which means
that the current value 400KHz is wrong.
Unfortunately this has also lead to fail to initialize some cards, which
are allowed to require 100KHz to work. So, let's fix the problem by
changing the minimal supported clock rate to 100KHz.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221011104935.10980-1-wenchao.chen666@gmail.com
[Ulf: Clarified to commit-message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b78870e7f41534cc719c295d1f8809aca93aeeab upstream.
Ensure tegra_host member "curr_clk_rate" holds the actual clock rate
instead of requested clock rate for proper use during tuning correction
algorithm. Actual clk rate may not be the same as the requested clk
frequency depending on the parent clock source set. Tuning correction
algorithm depends on certain parameters which are sensitive to current
clk rate. If the host clk is selected instead of the actual clock rate,
tuning correction algorithm may end up applying invalid correction,
which could result in errors
Fixes: ea8fc5953e8b ("mmc: tegra: update hw tuning process")
Signed-off-by: Aniruddha TVS Rao <anrao@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221006130622.22900-4-pshete@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0c00454bf78975925eccc9737faaa4d4951edbf upstream.
Due to clk rounding errors on RZ/G2L platforms, it selects a clock source
with a lower clock rate compared to a higher one.
For eg: The rounding error (533333333 Hz / 4 * 4 = 533333332 Hz < 5333333
33 Hz) selects a clk source of 400 MHz instead of 533.333333 MHz.
This patch fixes this issue by adding a margin of (1/1024) higher to
the clock rate.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: bb6d3fa98a41 ("clk: renesas: rcar-gen3: Switch to new SD clock handling")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220928110755.849275-1-biju.das.jz@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07d2872bf4c864eb83d034263c155746a2fb7a3b upstream.
Some SD-cards from Sandisk that are SDA-6.0 compliant reports they supports
discard, while they actually don't. This might cause mk2fs to fail while
trying to format the card and revert it to a read-only mode.
To fix this problem, let's add a card quirk (MMC_QUIRK_BROKEN_SD_DISCARD)
to indicate that we shall fall-back to use the legacy erase command
instead.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220928095744.16455-1-avri.altman@wdc.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The block device uses multiple queues to access emmc. There will be up to 3
requests in the hsq of the host. The current code will check whether there
is a request doing recovery before entering the queue, but it will not check
whether there is a request when the lock is issued. The request is in recovery
mode. If there is a request in recovery, then a read and write request is
initiated at this time, and the conflict between the request and the recovery
request will cause the data to be trampled.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: 511ce378e16f ("mmc: Add MMC host software queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220916090506.10662-1-wenchao.chen666@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This loop intends to retry a max of 10 times, with some implicit
termination based on the SD_{R,}OCR_S18A bit. Unfortunately, the
termination condition depends on the value reported by the SD card
(*rocr), which may or may not correctly reflect what we asked it to do.
Needless to say, it's not wise to rely on the card doing what we expect;
we should at least terminate the loop regardless. So, check both the
input and output values, so we ensure we will terminate regardless of
the SD card behavior.
Note that SDIO learned a similar retry loop in commit 0797e5f1453b
("mmc: core: Fixup signal voltage switch"), but that used the 'ocr'
result, and so the current pre-terminating condition looks like:
rocr & ocr & R4_18V_PRESENT
(i.e., it doesn't have the same bug.)
This addresses a number of crash reports seen on ChromeOS that look
like the following:
... // lots of repeated: ...
<4>[13142.846061] mmc1: Skipping voltage switch
<4>[13143.406087] mmc1: Skipping voltage switch
<4>[13143.964724] mmc1: Skipping voltage switch
<4>[13144.526089] mmc1: Skipping voltage switch
<4>[13145.086088] mmc1: Skipping voltage switch
<4>[13145.645941] mmc1: Skipping voltage switch
<3>[13146.153969] INFO: task halt:30352 blocked for more than 122 seconds.
...
Fixes: f2119df6b764 ("mmc: sd: add support for signal voltage switch procedure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220914014010.2076169-1-briannorris@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the datasheet [1] at page 377, 4-bit bus width is turned on by
bit 2 of the Bus Width Register. Thus the current bitmask is wrong: define
BUS_WIDTH_4 BIT(1)
BIT(1) does not work but BIT(2) works. This has been verified on real MOXA
hardware with FTSDC010 controller revision 1_6_0.
The corrected value of BUS_WIDTH_4 mask collides with: define BUS_WIDTH_8
BIT(2). Additionally, 8-bit bus width mode isn't supported according to the
datasheet, so let's remove the corresponding code.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220907205753.1577434-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When data crc occurs, the kernel will panic because host->cmd is null.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: efe8f5c9b5e1 ("mmc: sdhci: Capture eMMC and SD card errors")
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220907035847.13783-1-wenchao.chen666@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix workaround for SD UHS-I voltage switch
* tag 'mmc-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failure
mmc: core: Fix UHS-I SD 1.8V workaround branch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Fix for a mmc test and to load .kunit_test_suites section when
CONFIG_KUNIT=m, and not just when KUnit is built-in"
* tag 'linux-kselftest-kunit-fixes-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
module: kunit: Load .kunit_test_suites section when CONFIG_KUNIT=m
mmc: sdhci-of-aspeed: test: Fix dependencies when KUNIT=m
|
|
If re-initialization results is a different signal voltage, because the
voltage switch failed previously, but not this time (or vice versa), then
sd3_bus_mode will be inconsistent with the card because the SD_SWITCH
command is done only upon first initialization.
Fix by always reading SD_SWITCH information during re-initialization, which
also means it does not need to be re-read later for the 1.8V fixup
workaround.
Note, brief testing showed SD_SWITCH took about 1.8ms to 2ms which added
about 1% to 1.5% to the re-initialization time, so it's not particularly
significant.
Reported-by: Seunghui Lee <sh043.lee@samsung.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Seunghui Lee <sh043.lee@samsung.com>
Tested-by: Seunghui Lee <sh043.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220815073321.63382-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When introduced, upon success, the 1.8V fixup workaround in
mmc_sd_init_card() would branch to practically the end of the function, to
a label named "done". Unfortunately, perhaps due to the label name, over
time new code has been added that really should have come after "done" not
before it. Let's fix the problem by moving the label to the correct place
and rename it "cont".
Fixes: 045d705dc1fb ("mmc: core: Enable the MMC host software queue for the SD card")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Seunghui Lee <sh043.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220815073321.63382-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While the sdhci-of-aspeed KUnit tests do work when builtin, and do work
when KUnit itself is being built as a module, the two together break.
This is because the KUnit tests (understandably) depend on KUnit, so a
built-in test cannot build if KUnit is a module.
Fix this by adding a dependency on (MMC_SDHCI_OF_ASPEED=m || KUNIT=y),
which only excludes this one problematic configuration.
This was reported on a nasty openrisc-randconfig run by the kernel test
robot, though for some reason (compiler optimisations removing the test
code?) I wasn't able to reproduce it locally on x86:
https://lore.kernel.org/linux-mm/202207140122.fzhlf60k-lkp@intel.com/T/
Fixes: 291cd54e5b05 ("mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The commit 08f3dff799d4 (mmc: sdhci-of-dwcmshc: add rockchip platform
support") introduces the use of_device_get_match_data() to check for some
chips. Unfortunately, it also breaks the BlueField-3 FW, which uses ACPI.
To fix the problem, let's add the ACPI match data and the corresponding
quirks to re-enable the support for the BlueField-3 SoC.
Reviewed-by: David Woods <davwoods@nvidia.com>
Signed-off-by: Liming Sun <limings@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 08f3dff799d4 ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220809173742.178440-1-limings@nvidia.com
[Ulf: Clarified the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit in Fixes has introduced a new error handling which should goto
the existing error handling path.
Otherwise some resources leak.
Fixes: 19c6beaa064c ("mmc: meson-gx: add device reset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/be4b863bacf323521ba3a02efdc4fca9cdedd1a6.1659855351.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently we don't clear MSDC interrupts when cqe off/disable, which led
to the data complete interrupt will be reserved for the next command.
If the next command with data transfer after cqe off/disable, we process
the CMD ready interrupt and trigger DMA start for data, but the data
complete interrupt is already exists, then SW assume that the data transfer
is complete, SW will trigger DMA stop, but the data may not be transmitted
yet or is transmitting, so we may encounter the following error:
mtk-msdc 11230000.mmc: CMD bus busy detected.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220728080048.21336-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit in Fixes: has introduced an new error handling without branching
to the existing error handling path.
Update it now and release some resources if pxamci_init_ocr() fails.
Fixes: 61951fd6cb49 ("mmc: pxamci: let mmc core handle regulators")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/07a2dcebf8ede69b484103de8f9df043f158cffd.1658862932.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit in Fixes: has moved some code around without updating gotos to
the error handling path.
Update it now and release some resources if pxamci_of_init() fails.
Fixes: fa3a5115469c ("mmc: pxamci: call mmc_of_parse()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/6d75855ad4e2470e9ed99e0df21bc30f0c925a29.1658862932.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups"
* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
mmc: mediatek: add support for SDIO eint wakup IRQ
mmc: core: Add support for SDIO wakeup interrupt
dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
mmc: renesas_sdhi: newer SoCs don't need manual tap correction
mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
mmc: cavium-octeon: Add of_node_put() when breaking out of loop
mmc: core: quirks: Add of_node_put() when breaking out of loop
mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
mmc: sdhci-msm: drop redundant of_device_id entries
dt-bindings: mmc: sdhci-msm: add MSM8998
mmc: block: Add single read for 4k sector cards
mmc: mxcmmc: Use mmc_card_sdio macro
mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
dt-bindings: mmc: sdhci-msm: fix reg-names entries
dt-bindings: mmc: Add compatible for MediaTek MT8188
dt-bindings: mmc: sdhci-msm: document resets
mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
|
|
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
|
|
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
|
|
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If wakeup-source flag is set in host dts node, parse EAI information
from SDIO CCCR interrupt externsion segment for in-band wakeup. If
async interrupt is supported by SDIO card then enable it and set
enable_async_irq flag in sdio_cccr structure to 1. The parse flow is
implemented in sdio_read_cccr().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased, renamed the quirk variable, removed stale comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220720072901.1266-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In thunder_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 166bac38c3c5 ("mmc: cavium: Add MMC PCI driver for ThunderX SOCs")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-2-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In octeon_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 01d95843335c ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.
Fixes: b360b1102670 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of adding disk failure, the disk needs to be released, otherwise
disk/queue is leaked.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220718160851.312972-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
