summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)AuthorFilesLines
2021-03-17mmc: core: Fix partition switch time for eMMCAdrian Hunter1-4/+11
commit 66fbacccbab91e6e55d9c8f1fc0910a8eb6c81f7 upstream. Avoid the following warning by always defining partition switch time: [ 3.209874] mmc1: unspecified timeout for CMD6 - use generic [ 3.222780] ------------[ cut here ]------------ [ 3.233363] WARNING: CPU: 1 PID: 111 at drivers/mmc/core/mmc_ops.c:575 __mmc_switch+0x200/0x204 Reported-by: Paul Fertser <fercerpav@gmail.com> Fixes: 1c447116d017 ("mmc: mmc: Fix partition switch timeout for some eMMCs") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/168bbfd6-0c5b-5ace-ab41-402e7937c46e@intel.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-17mmc: mediatek: fix race condition between msdc_request_timeout and irqChaotian Jing1-8/+10
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ] when get request SW timeout, if CMD/DAT xfer done irq coming right now, then there is race between the msdc_request_timeout work and irq handler, and the host->cmd and host->data may set to NULL in irq handler. also, current flow ensure that only one path can go to msdc_request_done(), so no need check the return value of cancel_delayed_work(). Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-17mmc: mxs-mmc: Fix a resource leak in an error handling path in 'mxs_mmc_probe()'Christophe JAILLET1-1/+1
[ Upstream commit 0bb7e560f821c7770973a94e346654c4bdccd42c ] If 'mmc_of_parse()' fails, we must undo the previous 'dma_request_chan()' call. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201208203527.49262-1-christophe.jaillet@wanadoo.fr Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-07mmc: sdhci-esdhc-imx: fix kernel panic when remove moduleFrank Li1-1/+2
commit a56f44138a2c57047f1ea94ea121af31c595132b upstream. In sdhci_esdhc_imx_remove() the SDHCI_INT_STATUS in read. Under some circumstances, this may be done while the device is runtime suspended, triggering the below splat. Fix the problem by adding a pm_runtime_get_sync(), before reading the register, which will turn on clocks etc making the device accessible again. [ 1811.323148] mmc1: card aaaa removed [ 1811.347483] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP [ 1811.354988] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core [last unloaded: mmc_core] [ 1811.365726] CPU: 0 PID: 3464 Comm: rmmod Not tainted 5.10.1-sd-99871-g53835a2e8186 #5 [ 1811.373559] Hardware name: Freescale i.MX8DXL EVK (DT) [ 1811.378705] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 1811.384723] pc : sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx] [ 1811.391090] lr : platform_drv_remove+0x2c/0x50 [ 1811.395536] sp : ffff800012c7bcb0 [ 1811.398855] x29: ffff800012c7bcb0 x28: ffff00002c72b900 [ 1811.404181] x27: 0000000000000000 x26: 0000000000000000 [ 1811.409497] x25: 0000000000000000 x24: 0000000000000000 [ 1811.414814] x23: ffff0000042b3890 x22: ffff800009127120 [ 1811.420131] x21: ffff00002c4c9580 x20: ffff0000042d0810 [ 1811.425456] x19: ffff0000042d0800 x18: 0000000000000020 [ 1811.430773] x17: 0000000000000000 x16: 0000000000000000 [ 1811.436089] x15: 0000000000000004 x14: ffff000004019c10 [ 1811.441406] x13: 0000000000000000 x12: 0000000000000020 [ 1811.446723] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f [ 1811.452040] x9 : fefefeff6364626d x8 : 7f7f7f7f7f7f7f7f [ 1811.457356] x7 : 78725e6473607372 x6 : 0000000080808080 [ 1811.462673] x5 : 0000000000000000 x4 : 0000000000000000 [ 1811.467990] x3 : ffff800011ac1cb0 x2 : 0000000000000000 [ 1811.473307] x1 : ffff8000091214d4 x0 : ffff8000133a0030 [ 1811.478624] Call trace: [ 1811.481081] sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx] [ 1811.487098] platform_drv_remove+0x2c/0x50 [ 1811.491198] __device_release_driver+0x188/0x230 [ 1811.495818] driver_detach+0xc0/0x14c [ 1811.499487] bus_remove_driver+0x5c/0xb0 [ 1811.503413] driver_unregister+0x30/0x60 [ 1811.507341] platform_driver_unregister+0x14/0x20 [ 1811.512048] sdhci_esdhc_imx_driver_exit+0x1c/0x3a8 [sdhci_esdhc_imx] [ 1811.518495] __arm64_sys_delete_module+0x19c/0x230 [ 1811.523291] el0_svc_common.constprop.0+0x78/0x1a0 [ 1811.528086] do_el0_svc+0x24/0x90 [ 1811.531405] el0_svc+0x14/0x20 [ 1811.534461] el0_sync_handler+0x1a4/0x1b0 [ 1811.538474] el0_sync+0x174/0x180 [ 1811.541801] Code: a9025bf5 f9403e95 f9400ea0 9100c000 (b9400000) [ 1811.547902] ---[ end trace 3fb1a3bd48ff7be5 ]--- Signed-off-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org # v4.0+ Link: https://lore.kernel.org/r/20210210181933.29263-1-Frank.Li@nxp.com [Ulf: Clarified the commit message a bit] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> [iwamatsu: adjust context] Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-03mmc: usdhi6rol0: Fix a resource leak in the error handling path of the probeChristophe JAILLET1-1/+3
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ] A call to 'ausdhi6_dma_release()' to undo a previous call to 'usdhi6_dma_request()' is missing in the error handling path of the probe function. It is already present in the remove function. Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-02-10mmc: core: Limit retries when analyse of SDIO tuples failsFengnan Chang1-0/+6
commit f92e04f764b86e55e522988e6f4b6082d19a2721 upstream. When analysing tuples fails we may loop indefinitely to retry. Let's avoid this by using a 10s timeout and bail if not completed earlier. Signed-off-by: Fengnan Chang <fengnanchang@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210123033230.36442-1-fengnanchang@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10mmc: via-sdmmc: Fix data race bugMadhuparna Bhowmik1-0/+3
[ Upstream commit 87d7ad089b318b4f319bf57f1daa64eb6d1d10ad ] via_save_pcictrlreg() should be called with host->lock held as it writes to pm_pcictrl_reg, otherwise there can be a race condition between via_sd_suspend() and via_sdc_card_detect(). The same pattern is used in the function via_reset_pcictrl() as well, where via_save_pcictrlreg() is called with host->lock held. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29mmc: sdio: Check for CISTPL_VERS_1 buffer sizePali Rohár1-0/+3
[ Upstream commit 8ebe2607965d3e2dc02029e8c7dd35fbe508ffd0 ] Before parsing CISTPL_VERS_1 structure check that its size is at least two bytes to prevent buffer overflow. Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-05-10mmc: sdhci: Fix regression setting power on Trats2 boardAdrian Hunter3-9/+56
commit 1dceb0415aa0c6bc11dacdab47c9ef83a3604166 upstream. Several commits relating to setting power have been introducing problems by putting driver-specific rules into generic SDHCI code. Krzysztof Kozlowski reported that after commit 918f4cbd4340 ("mmc: sdhci: restore behavior when setting VDD via external regulator") on Trats2 board there are warnings for invalid VDD value (2.8V): [ 3.119656] ------------[ cut here ]------------ [ 3.119666] WARNING: CPU: 3 PID: 90 at ../drivers/mmc/host/sdhci.c:1234 sdhci_do_set_ios+0x4cc/0x5e0 [ 3.119669] mmc0: Invalid vdd 0x10 [ 3.119673] Modules linked in: [ 3.119679] CPU: 3 PID: 90 Comm: kworker/3:1 Tainted: G W 4.5.0-next-20160324 #23 [ 3.119681] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [ 3.119690] Workqueue: events_freezable mmc_rescan [ 3.119708] [<c010e0ac>] (unwind_backtrace) from [<c010ae10>] (show_stack+0x10/0x14) [ 3.119719] [<c010ae10>] (show_stack) from [<c0323260>] (dump_stack+0x88/0x9c) [ 3.119728] [<c0323260>] (dump_stack) from [<c011b754>] (__warn+0xe8/0x100) [ 3.119734] [<c011b754>] (__warn) from [<c011b7a4>] (warn_slowpath_fmt+0x38/0x48) [ 3.119740] [<c011b7a4>] (warn_slowpath_fmt) from [<c0527d28>] (sdhci_do_set_ios+0x4cc/0x5e0) [ 3.119748] [<c0527d28>] (sdhci_do_set_ios) from [<c0528018>] (sdhci_runtime_resume_host+0x60/0x114) [ 3.119758] [<c0528018>] (sdhci_runtime_resume_host) from [<c0402570>] (__rpm_callback+0x2c/0x60) [ 3.119767] [<c0402570>] (__rpm_callback) from [<c04025c4>] (rpm_callback+0x20/0x80) [ 3.119773] [<c04025c4>] (rpm_callback) from [<c04034b8>] (rpm_resume+0x36c/0x558) [ 3.119780] [<c04034b8>] (rpm_resume) from [<c04036f0>] (__pm_runtime_resume+0x4c/0x64) [ 3.119788] [<c04036f0>] (__pm_runtime_resume) from [<c0512728>] (__mmc_claim_host+0x170/0x1b0) [ 3.119795] [<c0512728>] (__mmc_claim_host) from [<c0514e2c>] (mmc_rescan+0x54/0x348) [ 3.119807] [<c0514e2c>] (mmc_rescan) from [<c0130dac>] (process_one_work+0x120/0x3f4) [ 3.119815] [<c0130dac>] (process_one_work) from [<c01310b8>] (worker_thread+0x38/0x554) [ 3.119823] [<c01310b8>] (worker_thread) from [<c01365a4>] (kthread+0xdc/0xf4) [ 3.119831] [<c01365a4>] (kthread) from [<c0107878>] (ret_from_fork+0x14/0x3c) [ 3.119834] ---[ end trace a22d652aa3276886 ]--- Fix by adding a 'set_power' callback and restoring the default behaviour prior to commit 918f4cbd4340 ("mmc: sdhci: restore behavior when setting VDD via external regulator"). The desired behaviour of that commit is gotten by having sdhci-pxav3 provide its own set_power callback. Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Link: http://lkml.kernel.org/r/CAJKOXPcGDnPm-Ykh6wHqV1YxfTaov5E8iVqBoBn4OJc7BnhgEQ@mail.gmail.com Fixes: 918f4cbd4340 ("mmc: sdhci: restore behavior when setting VDD...) Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org # v4.5+ Reviewed-by: Jisheng Zhang <jszhang@marvell.com> Tested-by: Jisheng Zhang <jszhang@marvell.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: moxart: fix wait_for_completion_interruptible_timeout return variable typeNicholas Mc Guire1-2/+3
commit 41f469cac2663a41a7b0c84cb94e8f7024385ae4 upstream. wait_for_completion_timeout_interruptible returns long not unsigned long so dma_time, which is used exclusively here, is changed to long. Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver") Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: dw_mmc: rockchip: Set the drive phase properlyDouglas Anderson1-0/+64
commit d4aa908c7978f60557a799ca53b5ae4166fd8355 upstream. Historically for Rockchip devices we've relied on the power-on default (or perhaps the firmware setting) to get the correct drive phase for dw_mmc devices. This worked OK for the most part, but: * Relying on the setting just "being right" is a bit fragile. * As soon as there is an instance where the power on default is wrong or where the firmware didn't configure this properly then we'll get a mysterious failure. In commit 7a03fe6f48f3 ("clk: rockchip: reset init state before mmc card initialization") we actually started setting this explicitly in the kernel, but that commit wasn't quite right and also wasn't quite enough. See <https://patchwork.kernel.org/patch/9085311/> for some details. Let's explicitly set this phase in dw_mmc. The comments inside this patch try to explain the situation quite throughly, but the high level overview of this is: Before this patch on rk3288 devices tested (after revert of the clock patch described above): * eMMC: 180 degrees * SDMMC/SDIO0/SDIO1: 90 degrees After this patch: * Use 90 degree phase offset usually. * Use 180 degree phase offset for MMC_DDR52, SDR104, HS200. That means we are _changing_ behavior for those devices in this way: * If we have HS200 eMMC or DDR52 eMMC, we'll run ID mode at 90 degrees (vs 180) but otherwise have no change. * For any non-HS200 / non-DDR52 eMMC devices we'll now _always_ run at 90 degrees (vs 180). It seems fairly unlikely that building modern hardware is using an eMMC that isn't using DDR52 or HS200, of course. * For SDR104 cards we'll now run with 180 degree phase offset (vs 90). It's expected that 90 degree phase offset would have worked OK, but this gives us extra margin. I have tested this by inserting my collection of uSD cards (mostly UHS, though a few not) into a veyron_minnie and confirmed that they still seem to enumerate properly. For a subset of them I tried putting a filesystem on them and also tried running mmc_test. Fixes: 7a03fe6f48f3 ("clk: rockchip: reset init state before mmc card initialization") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: block: return error on failed mmc_blk_get()Olof Johansson1-1/+3
commit f00ab14c252ac459e86194747a1f580ab503c954 upstream. This used to return -EFAULT, but the function above returns -EINVAL on the same condition so let's stick to that. The removal of error return on this path was introduced with b093410c9aef ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD'). Fixes: b093410c9aef ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD'). Signed-off-by: Olof Johansson <olof@lixom.net> Cc: Grant Grundler <grundler@google.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: debugfs: correct wrong voltage valueChuanxiao Dong1-1/+1
commit 0036e74686344f1051afc3107740140abfd03616 upstream. Correct the wrong voltage value shown in debugfs for mmc/sd/sdio. Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com> Fixes: 42cd95a0603e ("mmc: core: debugfs: Add signal_voltage to ios dump") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: sd: limit SD card power limit according to cards capabilitiesRussell King1-4/+16
commit d9812780a020bcec44565b5950b2a8b31afb5545 upstream. The SD card specification allows cards to error out a SWITCH command where the requested function in a group is not supported. The spec provides for a set of capabilities which indicate which functions are supported. In the case of the power limit, requesting an unsupported power level via the SWITCH command fails, resulting in the power level remaining at the power-on default of 0.72W, even though the host and card may support higher powers levels. This has been seen with SanDisk 8GB cards, which support the default 0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host, supporting up to 2.88W (800mA). This currently causes us to try to set a power limit function value of '3' (2.88W) which the card errors out on, and thereby causes the power level to remain at 0.72W rather than the desired 1.44W. Arrange to limit the selected current limit by the capabilities reported by the card to avoid the SWITCH command failing. Select the highest current limit that the host and card combination support. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Fixes: a39ca6ae0a08 ("mmc: core: Simplify and fix for SD switch processing") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-10mmc: sdhci: restore behavior when setting VDD via external regulatorJisheng Zhang1-13/+6
commit 918f4cbd4340ddd1eb389cd8efa3b07ac74ec4c0 upstream. After commit 52221610dd84 ("mmc: sdhci: Improve external VDD regulator support"), for the VDD is supplied via external regulators, we ignore the code to convert a VDD voltage request into one of the standard SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This brings two issues: 1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any more. 2. What's more, once SDHCI_POWER_ON bit is set, some controllers such as the sdhci-pxav3 used in marvell berlin SoCs require the voltage levels programming in the SDHCI_POWER_CONTROL register, even the VDD is supplied by external regulator. So the host in marvell berlin SoCs still works fine after the commit. However, commit 3cbc6123a93d ("mmc: sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON bit, this would make the host in marvell berlin SoCs won't work any more with external vmmc. This patch restores the behavior when setting VDD through external regulator by moving the call of mmc_regulator_set_ocr() to the end of sdhci_set_power() function. After this patch, the sdcard on Marvell Berlin SoC boards work again. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Fixes: 52221610dd84 ("mmc: sdhci: Improve external VDD ...") Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-15mmc: spi: Toggle SPI polarity, do not hardcode itLinus Walleij1-3/+8
commit af3ed119329cf9690598c5a562d95dfd128e91d6 upstream. The code in mmc_spi_initsequence() tries to send a burst with high chipselect and for this reason hardcodes the device into SPI_CS_HIGH. This is not good because the SPI_CS_HIGH flag indicates logical "asserted" CS not always the physical level. In some cases the signal is inverted in the GPIO library and in that case SPI_CS_HIGH is already set, and enforcing SPI_CS_HIGH again will actually drive it low. Instead of hard-coding this, toggle the polarity so if the default is LOW it goes high to assert chipselect but if it is already high then toggle it low instead. Cc: Phil Elwell <phil@raspberrypi.org> Reported-by: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: sdhci: fix minimum clock rate for v3 controllerMichał Mirosław1-4/+6
commit 2a187d03352086e300daa2044051db00044cd171 upstream. For SDHCIv3+ with programmable clock mode, minimal clock frequency is still base clock / max(divider). Minimal programmable clock frequency is always greater than minimal divided clock frequency. Without this patch, SDHCI uses out-of-spec initial frequency when multiplier is big enough: mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz [for 480 MHz source clock divided by 1024] The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode. Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present Cc: <stable@vger.kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04mmc: sdhci: Update the tuning failed messages to pr_debug levelFaiz Abbas1-1/+1
[ Upstream commit 2c92dd20304f505b6ef43d206fff21bda8f1f0ae ] Tuning support in DDR50 speed mode was added in SD Specifications Part1 Physical Layer Specification v3.01. Its not possible to distinguish between v3.00 and v3.01 from the SCR and that is why since commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode") tuning failures are ignored in DDR50 speed mode. Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this error gets printed during enumeration and also if retune is triggered at any time during operation. Update the printk level to pr_debug so that these errors don't lead to false error reports. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Cc: stable@vger.kernel.org # v4.4+ Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04mmc: sdhci-of-esdhc: fix P2020 errata handlingYangbo Lu1-2/+2
commit fe0acab448f68c3146235afe03fb932e242ec94c upstream. Two previous patches introduced below quirks for P2020 platforms. - SDHCI_QUIRK_RESET_AFTER_REQUEST - SDHCI_QUIRK_BROKEN_TIMEOUT_VAL The patches made a mistake to add them in quirks2 of sdhci_host structure, while they were defined for quirks. host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; This patch is to fix them. host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support") Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-04Revert "mmc: sdhci: Fix incorrect switch to HS mode"Faiz Abbas1-3/+1
commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream. This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37. This commit aims to treat SD High speed and SDR25 as the same while setting UHS Timings in HOST_CONTROL2 which leads to failures with some SD cards in AM65x. Revert this commit. The issue this commit was trying to fix can be implemented in a platform specific callback instead of common sdhci code. Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-28mmc: block: Fix tag condition with packed writesAdrian Hunter1-2/+1
commit d806b46e5f496a6335ebd7f8432d2533507ce9a2 upstream. Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data size even though 'brq' has not been set up. Instead use blk_rq_sectors(). Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-28mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready failChaotian Jing1-1/+1
[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ] when msdc_cmd_is_ready return fail, the req_timeout work has not been inited and cancel_delayed_work() will return false, then, the request return directly and never call mmc_request_done(). so need call mod_delayed_work() before msdc_cmd_is_ready() Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-25mmc: sdhci-of-at91: fix quirk2 overwriteEugen Hristev1-1/+1
commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream. The quirks2 are parsed and set (e.g. from DT) before the quirk for broken HS200 is set in the driver. The driver needs to enable just this flag, not rewrite the whole quirk set. Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-05mmc: sdhci: Fix incorrect switch to HS modeAl Cooper1-1/+3
[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ] When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode. This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set. The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode. This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-09-06mmc: core: Fix init of SD cards reporting an invalid VDD rangeUlf Hansson1-0/+6
commit 72741084d903e65e121c27bd29494d941729d4a1 upstream. The OCR register defines the supported range of VDD voltages for SD cards. However, it has turned out that some SD cards reports an invalid voltage range, for example having bit7 set. When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from the invalid VDD range, this triggers the core to run a power cycle of the card to try to initialize it at the lowest common supported voltage. Obviously this fails, since the card can't support it. Let's fix this problem, by clearing invalid bits from the read OCR register for SD cards, before proceeding with the VDD voltage negotiation. Cc: stable@vger.kernel.org Reported-by: Philip Langdale <philipl@overt.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Philip Langdale <philipl@overt.org> Tested-by: Philip Langdale <philipl@overt.org> Tested-by: Manuel Presnitz <mail@mpy.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-06mmc: sdhci-of-at91: add quirk for broken HS200Eugen Hristev1-0/+3
commit 7871aa60ae0086fe4626abdf5ed13eeddf306c61 upstream. HS200 is not implemented in the driver, but the controller claims it through caps. Remove it via a quirk, to make sure the mmc core do not try to enable HS200, as it causes the eMMC initialization to fail. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-11mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 supportYinbo Zhu1-1/+3
[ Upstream commit 05cb6b2a66fa7837211a060878e91be5eb10cb07 ] eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock), and 0xC(2^25 SD clock). The data timeout counter can count from 2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout counter counts for only 2^13 SD clocks. A-008358: The data timeout counter value loaded into the timeout counter is less than expected and can result into early timeout error in case of eSDHC data transactions. The table below shows the expected vs actual timeout period for different values of SYSCTL[DTOCV]: these two erratum has the same quirk to control it, and set SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-11mmc: sdhci-of-esdhc: add erratum eSDHC5 supportYinbo Zhu1-0/+3
[ Upstream commit a46e42712596b51874f04c73f1cdf1017f88df52 ] Software writing to the Transfer Type configuration register (system clock domain) can cause a setup/hold violation in the CRC flops (card clock domain), which can cause write accesses to be sent with corrupt CRC values. This issue occurs only for write preceded by read. this erratum is to fix this issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-11mmc_spi: add a status check for spi_sync_lockedKangjie Lu1-0/+4
[ Upstream commit 611025983b7976df0183390a63a2166411d177f1 ] In case spi_sync_locked fails, the fix reports the error and returns the error code upstream. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-11mmc: core: Verify SD bus widthRaul E Rangel1-0/+8
[ Upstream commit 9e4be8d03f50d1b25c38e2b59e73b194c130df7d ] The SD Physical Layer Spec says the following: Since the SD Memory Card shall support at least the two bus modes 1-bit or 4-bit width, then any SD Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101"). This change verifies the card has specified a bus width. AMD SDHC Device 7806 can get into a bad state after a card disconnect where anything transferred via the DATA lines will always result in a zero filled buffer. Currently the driver will continue without error if the HC is in this condition. A block device will be created, but reading from it will result in a zero buffer. This makes it seem like the SD device has been erased, when in actuality the data is never getting copied from the DATA lines to the data buffer. SCR is the first command in the SD initialization sequence that uses the DATA lines. By checking that the response was invalid, we can abort mounting the card. Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Raul E Rangel <rrangel@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-27mmc: davinci: remove extraneous __init annotationArnd Bergmann1-1/+1
[ Upstream commit 9ce58dd7d9da3ca0d7cb8c9568f1c6f4746da65a ] Building with clang finds a mistaken __init tag: WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host() The function davinci_mmcsd_probe() references the function __init init_mmcsd_host(). This is often because davinci_mmcsd_probe lacks a __init annotation or the annotation of init_mmcsd_host is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-27mmc: omap: fix the maximum timeout settingAaro Koskinen1-1/+1
[ Upstream commit a6327b5e57fdc679c842588c3be046c0b39cc127 ] When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy: MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! [ad inf.] Emulator warnings appear to be valid. The TI document SPRU680 [1] ("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card (MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253 cycles and "0xff and 0xfe cannot be used". Fix by using 0xfd as the maximum timeout. Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810 (OMAP2420) that MMC works as before. [1] http://www.ti.com/lit/ug/spru680/spru680.pdf Fixes: 730c9b7e6630f ("[MMC] Add OMAP MMC host driver") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-03mmc: mmc: fix switch timeout issue caused by jiffies precisionChaotian Jing1-1/+1
[ Upstream commit 987aa5f8059613bf85cbb6f64ffbd34f5cb7a9d1 ] with CONFIG_HZ=100, the precision of jiffies is 10ms, and the generic_cmd6_time of some card is also 10ms. then, may be current time is only 5ms, but already timed out caused by jiffies precision. Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-03Revert "mmc: block: don't use parameter prefix if built as module"Ulf Hansson1-3/+0
[ Upstream commit a5ebb87db84392edfd3142c3a6a78431d820a789 ] This reverts commit 829b6962f7e3cfc06f7c5c26269fd47ad48cf503. Revert this change as it causes a sysfs path to change and therefore introduces and ABI regression. More precisely Android's vold is not being able to access /sys/module/mmcblk/parameters/perdev_minors any more, since the path becomes changed to: "/sys/module/mmc_block/..." Fixes: 829b6962f7e3 ("mmc: block: don't use parameter prefix if built as module") Reported-by: John Stultz <john.stultz@linaro.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-03mmc: block: Allow more than 8 partitions per cardColin Cross1-5/+2
[ Upstream commit 382c55f88ffeb218c446bf0c46d0fc25d2795fe2 ] It is quite common for Android devices to utilize more then 8 partitions on internal eMMC storage. The vanilla kernel can support this via CONFIG_MMC_BLOCK_MINORS, however that solution caps the system to 256 minors total, which limits the number of mmc cards the system can support. This patch, which has been carried for quite awhile in the AOSP common tree, provides an alternative solution that doesn't seem to limit the total card count. So I wanted to submit it for consideration upstream. This patch sets the GENHD_FL_EXT_DEVT flag, which will allocate minor number in major 259 for partitions past disk->minors. It also removes the use of disk_devt to determine devidx from md->disk. md->disk->first_minor is always initialized from devidx and can always be used to recover it. Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Chuanxiao Dong <chuanxiao.dong@intel.com> Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Austin S Hemmelgarn <ahferroin7@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Android Kernel Team <kernel-team@android.com> Cc: linux-mmc@vger.kernel.org Signed-off-by: Colin Cross <ccross@android.com> [jstultz: Added context to commit message] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-03mmc: core: fix using wrong io voltage if mmc_select_hs200 failsDong Aisheng1-3/+9
commit e51534c806609c806d81bfb034f02737461f855c upstream. Currently MMC core will keep going if HS200/HS timing switch failed with -EBADMSG error by the assumption that the old timing is still valid. However, for mmc_select_hs200 case, the signal voltage may have already been switched. If the timing switch failed, we should fall back to the old voltage in case the card is continue run with legacy timing. If fall back signal voltage failed, we explicitly report an EIO error to force retry during the next power cycle. Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: core: shut up "voltage-ranges unspecified" pr_info()Russell King1-2/+6
commit 10a16a01d8f72e80f4780e40cf3122f4caffa411 upstream. Each time a driver such as sdhci-esdhc-imx is probed, we get a info printk complaining that the DT voltage-ranges property has not been specified. However, the DT binding specifically says that the voltage-ranges property is optional. That means we should not be complaining that DT hasn't specified this property: by indicating that it's optional, it is valid not to have the property in DT. Silence the warning if the property is missing. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: sanitize 'bus width' in debug outputWolfram Sang2-2/+2
commit ed9feec72fc1fa194ebfdb79e14561b35decce63 upstream. The bus width is sometimes the actual bus width, and sometimes indices to different arrays encoding the bus width. In my debugging case "2" could mean 8-bit as well as 4-bit, which was extremly confusing. Let's use the human-readable actual bus width in all places. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: make MAN_BKOPS_EN message a debugWolfram Sang1-1/+1
commit 4ec96b4cbde8d5714a4477b5a2562c3dd40bc5fa upstream. IMO this info is only useful for developers. Most users won't need this information, since there is not much they can do about it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: debugfs: Add a restriction to mmc debugfs clock settingChuanxiao Dong1-1/+1
commit e5905ff1281f0a0f5c9863c430ac1ed5faaf5707 upstream. Clock frequency values written to an mmc host should not be less than the minimum clock frequency which the mmc host supports. Signed-off-by: Yuan Juntao <juntaox.yuan@intel.com> Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: pwrseq_simple: Make reset-gpios optional to match docMartin Fuzzey1-8/+14
commit 64a67d4762ce3ce4c9466eadd152d825fbf84967 upstream. The DT binding doc says reset-gpios is an optional property but the code currently bails out if it is omitted. This is a regression since it breaks previously working device trees. Fix it by restoring the original documented behaviour. Fixes: ce037275861e ("mmc: pwrseq_simple: use GPIO descriptors array API") Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: tmio_mmc_core: don't claim spurious interruptsSergei Shtylyov1-5/+3
commit 5c27ff5db1491a947264d6d4e4cbe43ae6535bae upstream. I have encountered an interrupt storm during the eMMC chip probing (and the chip finally didn't get detected). It turned out that U-Boot left the DMAC interrupts enabled while the Linux driver didn't use those. The SDHI driver's interrupt handler somehow assumes that, even if an SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think that if none of the enabled interrupts happened and got handled, we should return IRQ_NONE -- that way the kernel IRQ code recoginizes a spurious interrupt and masks it off pretty quickly... Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03mmc: pxamci: fix enum type confusionArnd Bergmann1-1/+1
commit e60a582bcde01158a64ff948fb799f21f5d31a11 upstream. clang points out several instances of mismatched types in this drivers, all coming from a single declaration: drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion] direction = DMA_DEV_TO_MEM; ~ ^~~~~~~~~~~~~~ drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion] tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction, The behavior is correct, so this must be a simply typo from dma_data_direction and dma_transfer_direction being similarly named types with a similar purpose. Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-23mmc: spi: Fix card detection during probeJonathan Neuschäfer1-0/+1
commit c9bd505dbd9d3dc80c496f88eafe70affdcf1ba6 upstream. When using the mmc_spi driver with a card-detect pin, I noticed that the card was not detected immediately after probe, but only after it was unplugged and plugged back in (and the CD IRQ fired). The call tree looks something like this: mmc_spi_probe mmc_add_host mmc_start_host _mmc_detect_change mmc_schedule_delayed_work(&host->detect, 0) mmc_rescan host->bus_ops->detect(host) mmc_detect _mmc_detect_card_removed host->ops->get_cd(host) mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set) mmc_gpiod_request_cd ctx->cd_gpio = desc To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ is registered. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-06mmc: sdhci-iproc: handle mmc_of_parse() errors during probeStefan Wahren1-1/+4
commit 2bd44dadd5bfb4135162322fd0b45a174d4ad5bf upstream. We need to handle mmc_of_parse() errors during probe. This finally fixes the wifi regression on Raspberry Pi 3 series. In error case the wifi chip was permanently in reset because of the power sequence depending on the deferred probe of the GPIO expander. Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver") Cc: stable@vger.kernel.org Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-26mmc: atmel-mci: do not assume idle after atmci_request_endJonas Danielsson1-1/+2
[ Upstream commit ae460c115b7aa50c9a36cf78fced07b27962c9d0 ] On our AT91SAM9260 board we use the same sdio bus for wifi and for the sd card slot. This caused the atmel-mci to give the following splat on the serial console: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44 Modules linked in: CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14 Hardware name: Atmel AT91SAM9 [<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14) [<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4) [<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24) [<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44) [<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc) [<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164) [<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0) [<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330) [<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310) [<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac) [<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118) [<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118) [<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34) ---[ end trace 594371ddfa284bd6 ]--- This is: WARN_ON(host->cmd); This was fixed on our board by letting atmci_request_end determine what state we are in. Instead of unconditionally setting it to STATE_IDLE on STATE_END_REQUEST. Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-01-13mmc: omap_hsmmc: fix DMA API warningRussell King1-1/+11
commit 0b479790684192ab7024ce6a621f93f6d0a64d92 upstream. While booting with rootfs on MMC, the following warning is encountered on OMAP4430: omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536] This is because the DMA engine has a default maximum segment size of 64K but HSMMC sets: mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; mmc->max_seg_size = mmc->max_req_size; which ends up telling the block layer that we support a maximum segment size of 65535*512, which exceeds the advertised DMA engine capabilities. Fix this by clamping the maximum segment size to the lower of the maximum request size and of the DMA engine device used for either DMA channel. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-13mmc: core: Reset HPI enabled state during re-init and in case of errorsUlf Hansson1-1/+3
commit a0741ba40a009f97c019ae7541dc61c1fdf41efb upstream. During a re-initialization of the eMMC card, we may fail to re-enable HPI. In these cases, that isn't properly reflected in the card->ext_csd.hpi_en bit, as it keeps being set. This may cause following attempts to use HPI, even if's not enabled. Let's fix this! Fixes: eb0d8f135b67 ("mmc: core: support HPI send command") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-21MMC: OMAP: fix broken MMC on OMAP15XX/OMAP5910/OMAP310Aaro Koskinen1-2/+9
commit e8cde625bfe8a714a856e1366bcbb259d7346095 upstream. Since v2.6.22 or so there has been reports [1] about OMAP MMC being broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") that changed clock enabling to be done on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX the hardware doesn't seem to like it and the MMC just stops responding. Fix by memorizing the power mode and do the init only when necessary. Before the patch (on Palm TE): mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmci-omap mmci-omap.0: command timeout (CMD8) mmci-omap mmci-omap.0: command timeout (CMD18) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD13) mmci-omap mmci-omap.0: command timeout (CMD12) [x 6] mmci-omap mmci-omap.0: command timeout (CMD13) [x 6] mmcblk0: error -110 requesting status mmcblk0: recovery failed! print_req_error: I/O error, dev mmcblk0, sector 0 Buffer I/O error on dev mmcblk0, logical block 0, async page read mmcblk0: unable to read partition table After the patch: mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SDC 977 MiB mmcblk0: p1 The patch is based on a fix and analysis done by Ladislav Michl. Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770) and OMAP2420 (Nokia N810). [1] https://marc.info/?t=123175197000003&r=1&w=2 Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON") Reported-by: Ladislav Michl <ladis@linux-mips.org> Reported-by: Andrzej Zaborowski <balrogg@gmail.com> Tested-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-21mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01Yu Zhao1-0/+3
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ] This device reports SDHCI_CLOCK_INT_STABLE even though it's not ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 | SDHCI_CLOCK_CARD_EN but only observed the first operand). mmc1: Timeout waiting for hardware cmd interrupt. mmc1: sdhci: ============ SDHCI REGISTER DUMP =========== mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603 mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001 mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000 mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03 mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083 mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077 mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8 mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000 mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000 mmc1: sdhci: Host ctl2: 0x00000008 mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000 mmc1: sdhci: ============================================ The problem happens during wakeup from S3. Adding a delay quirk after power up reliably fixes the problem. Signed-off-by: Yu Zhao <yuzhao@google.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-08 20:25:40 +0300