summaryrefslogtreecommitdiff
path: root/drivers/mmc/host
AgeCommit message (Collapse)AuthorFilesLines
2020-02-15mmc: sdhci-of-at91: fix memleak on clk_get failureMichał Mirosław1-3/+6
[ Upstream commit a04184ce777b46e92c2b3c93c6dcb2754cb005e1 ] sdhci_alloc_host() does its work not using managed infrastructure, so needs explicit free on error path. Add it where needed. Cc: <stable@vger.kernel.org> Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/b2a44d5be2e06ff075f32477e466598bb0f07b36.1577961679.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-02-15mmc: spi: Toggle SPI polarity, do not hardcode itLinus Walleij1-3/+8
commit af3ed119329cf9690598c5a562d95dfd128e91d6 upstream. The code in mmc_spi_initsequence() tries to send a burst with high chipselect and for this reason hardcodes the device into SPI_CS_HIGH. This is not good because the SPI_CS_HIGH flag indicates logical "asserted" CS not always the physical level. In some cases the signal is inverted in the GPIO library and in that case SPI_CS_HIGH is already set, and enforcing SPI_CS_HIGH again will actually drive it low. Instead of hard-coding this, toggle the polarity so if the default is LOW it goes high to assert chipselect but if it is already high then toggle it low instead. Cc: Phil Elwell <phil@raspberrypi.org> Reported-by: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: sdhci: fix minimum clock rate for v3 controllerMichał Mirosław1-4/+6
commit 2a187d03352086e300daa2044051db00044cd171 upstream. For SDHCIv3+ with programmable clock mode, minimal clock frequency is still base clock / max(divider). Minimal programmable clock frequency is always greater than minimal divided clock frequency. Without this patch, SDHCI uses out-of-spec initial frequency when multiplier is big enough: mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz [for 480 MHz source clock divided by 1024] The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode. Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present Cc: <stable@vger.kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-29mmc: tegra: fix SDR50 tuning overrideMichał Mirosław1-1/+1
commit f571389c0b015e76f91c697c4c1700aba860d34f upstream. Commit 7ad2ed1dfcbe inadvertently mixed up a quirk flag's name and broke SDR50 tuning override. Use correct NVQUIRK_ name. Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes") Cc: <stable@vger.kernel.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Link: https://lore.kernel.org/r/9aff1d859935e59edd81e4939e40d6c55e0b55f6.1578390388.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-27mmc: sdhci-brcmstb: handle mmc_of_parse() errors during probeStefan Wahren1-1/+3
[ Upstream commit 1e20186e706da8446f9435f2924cd65ab1397e73 ] We need to handle mmc_of_parse() errors during probe otherwise the MMC driver could start without proper initialization (e.g. power sequence). Fixes: 476bf3d62d5c ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-31mmc: sdhci-of-esdhc: fix P2020 errata handlingYangbo Lu1-2/+2
commit fe0acab448f68c3146235afe03fb932e242ec94c upstream. Two previous patches introduced below quirks for P2020 platforms. - SDHCI_QUIRK_RESET_AFTER_REQUEST - SDHCI_QUIRK_BROKEN_TIMEOUT_VAL The patches made a mistake to add them in quirks2 of sdhci_host structure, while they were defined for quirks. host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; This patch is to fix them. host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST; host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support") Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31mmc: sdhci: Update the tuning failed messages to pr_debug levelFaiz Abbas1-2/+2
commit 2c92dd20304f505b6ef43d206fff21bda8f1f0ae upstream. Tuning support in DDR50 speed mode was added in SD Specifications Part1 Physical Layer Specification v3.01. Its not possible to distinguish between v3.00 and v3.01 from the SCR and that is why since commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode") tuning failures are ignored in DDR50 speed mode. Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this error gets printed during enumeration and also if retune is triggered at any time during operation. Update the printk level to pr_debug so that these errors don't lead to false error reports. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Cc: stable@vger.kernel.org # v4.4+ Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31mmc: sdhci-of-esdhc: Revert "mmc: sdhci-of-esdhc: add erratum A-009204 support"Rasmus Villemoes1-3/+0
commit 8b6dc6b2d60221e90703babbc141f063b8a07e72 upstream. This reverts commit 5dd195522562542bc6ebe6e7bd47890d8b7ca93c. First, the fix seems to be plain wrong, since the erratum suggests waiting 5ms before setting setting SYSCTL[RSTD], but this msleep() happens after the call of sdhci_reset() which is where that bit gets set (if SDHCI_RESET_DATA is in mask). Second, walking the whole device tree to figure out if some node has a "fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to 100 us on our mpc8309 board. Walking the device tree is done under a raw_spin_lock, so this is obviously really bad on an -rt system, and a waste of time on all. In fact, since esdhc_reset() seems to get called around 100 times per second, that mpc8309 now spends 0.8% of its time determining that it is not a p2020. Whether those 100 calls/s are normal or due to some other bug or misconfiguration, regularly hitting a 100 us non-preemptible window is unacceptable. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31mmc: mediatek: fix CMD_TA to 2 for MT8173 HS200/HS400 modeChaotian Jing1-0/+3
commit 8f34e5bd7024d1ffebddd82d7318b1be17be9e9a upstream. there is a chance that always get response CRC error after HS200 tuning, the reason is that need set CMD_TA to 2. this modification is only for MT8173. Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Tested-by: Hsin-Yi Wang <hsinyi@chromium.org> Cc: stable@vger.kernel.org Fixes: 1ede5cb88a29 ("mmc: mediatek: Use data tune for CMD line tune") Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31Revert "mmc: sdhci: Fix incorrect switch to HS mode"Faiz Abbas1-3/+1
commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream. This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37. This commit aims to treat SD High speed and SDR25 as the same while setting UHS Timings in HOST_CONTROL2 which leads to failures with some SD cards in AM65x. Revert this commit. The issue this commit was trying to fix can be implemented in a platform specific callback instead of common sdhci code. Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-31mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requestsEugeniu Rosca1-1/+1
[ Upstream commit c91843463e9e821dc3b48fe37e3155fa38299f6e ] Isolated initially to renesas_sdhi_internal_dmac [1], Ulf suggested adding MMC_CAP_ERASE to the TMIO mmc core: On Fri, Nov 15, 2019 at 10:27:25AM +0100, Ulf Hansson wrote: -- snip -- This test and due to the discussions with Wolfram and you in this thread, I would actually suggest that you enable MMC_CAP_ERASE for all tmio variants, rather than just for this particular one. In other words, set the cap in tmio_mmc_host_probe() should be fine, as it seems none of the tmio variants supports HW busy detection at this point. -- snip -- Testing on R-Car H3ULCB-KF doesn't reveal any issues (v5.4-rc7): root@rcar-gen3:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk0 179:0 0 59.2G 0 disk <--- eMMC mmcblk0boot0 179:8 0 4M 1 disk mmcblk0boot1 179:16 0 4M 1 disk mmcblk1 179:24 0 30G 0 disk <--- SD card root@rcar-gen3:~# time blkdiscard /dev/mmcblk0 real 0m8.659s user 0m0.001s sys 0m1.920s root@rcar-gen3:~# time blkdiscard /dev/mmcblk1 real 0m1.176s user 0m0.001s sys 0m0.124s [1] https://lore.kernel.org/linux-renesas-soc/20191112134808.23546-1-erosca@de.adit-jv.com/ Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Originally-by: Harish Jenny K N <harish_kandiga@mentor.com> Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-17mmc: host: omap_hsmmc: add code for special init of wl1251 to get rid of ↵H. Nikolaus Schaller1-0/+30
pandora_wl1251_init_card commit f6498b922e57aecbe3b7fa30a308d9d586c0c369 upstream. Pandora_wl1251_init_card was used to do special pdata based setup of the sdio mmc interface. This does no longer work with v4.7 and later. A fix requires a device tree based mmc3 setup. Therefore we move the special setup to omap_hsmmc.c instead of calling some pdata supplied init_card function. The new code checks for a DT child node compatible to wl1251 so it will not affect other MMC3 use cases. Generally, this code was and still is a hack and should be moved to mmc core to e.g. read such properties from optional DT child nodes. Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.7+ [Ulf: Fixed up some checkpatch complaints] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-05mmc: meson-gx: make sure the descriptor is stopped on errorsJerome Brunet1-10/+63
[ Upstream commit 18f92bc02f1739b5c4d5b70009fbb7eada45bca3 ] On errors, if we don't stop the descriptor chain, it may continue to run and raise IRQ after we have called mmc_request_done(). This is bad because we won't be able to get cmd anymore and properly deal with the IRQ. This patch makes sure the descriptor chain is stopped before calling mmc_request_done() Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-12-01mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready failChaotian Jing1-1/+1
[ Upstream commit f38a9774ddde9d79b3487dd888edd8b8623552af ] when msdc_cmd_is_ready return fail, the req_timeout work has not been inited and cancel_delayed_work() will return false, then, the request return directly and never call mmc_request_done(). so need call mod_delayed_work() before msdc_cmd_is_ready() Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-24mmc: tmio: fix SCC error handling to avoid false positive CRC errorTakeshi Saito1-1/+2
[ Upstream commit 51b72656bb39fdcb8f3174f4007bcc83ad1d275f ] If an SCC error occurs during a read/write command execution, a false positive CRC error message is output. mmcblk0: response CRC error sending r/w cmd command, card status 0x900 check_scc_error() checks SCC_RVSREQ.RVSERR bit. RVSERR detects a correction error in the next (up or down) delay tap position. However, since the command is successful, only retuning needs to be executed. This has been confirmed by HW engineers. Thus, on SCC error, set retuning flag instead of setting an error code. Fixes: b85fb0a1c8ae ("mmc: tmio: Fix SCC error detection") Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> [wsa: updated comment and commit message, removed some braces] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-24mmc: tmio: Fix SCC error detectionMasaharu Hayakawa1-2/+2
[ Upstream commit b85fb0a1c8aeaaa40d08945d51a6656b512173f0 ] SDR104, HS200 and HS400 need to check for SCC error. If SCC error is detected, retuning is necessary. Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com> [Niklas: update commit message] Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-11-20mmc: sdhci-of-at91: fix quirk2 overwriteEugen Hristev1-1/+1
commit fed23c5829ecab4ddc712d7b0046e59610ca3ba4 upstream. The quirks2 are parsed and set (e.g. from DT) before the quirk for broken HS200 is set in the driver. The driver needs to enable just this flag, not rewrite the whole quirk set. Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-11mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherenceRussell King1-1/+6
commit 121bd08b029e03404c451bb237729cdff76eafed upstream. We must not unconditionally set the DMA snoop bit; if the DMA API is assuming that the device is not DMA coherent, and the device snoops the CPU caches, the device can see stale cache lines brought in by speculative prefetch. This leads to the device seeing stale data, potentially resulting in corrupted data transfers. Commonly, this results in a descriptor fetch error such as: mmc0: ADMA error mmc0: sdhci: ============ SDHCI REGISTER DUMP =========== mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00002202 mmc0: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000001 mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013 mmc0: sdhci: Present: 0x01f50008 | Host ctl: 0x00000038 mmc0: sdhci: Power: 0x00000003 | Blk gap: 0x00000000 mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x000040d8 mmc0: sdhci: Timeout: 0x00000003 | Int stat: 0x00000001 mmc0: sdhci: Int enab: 0x037f108f | Sig enab: 0x037f108b mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202 mmc0: sdhci: Caps: 0x35fa0000 | Caps_1: 0x0000af00 mmc0: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000 mmc0: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x001d8a33 mmc0: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x3f400e00 mmc0: sdhci: Host ctl2: 0x00000000 mmc0: sdhci: ADMA Err: 0x00000009 | ADMA Ptr: 0x000000236d43820c mmc0: sdhci: ============================================ mmc0: error -5 whilst initialising SD card but can lead to other errors, and potentially direct the SDHCI controller to read/write data to other memory locations (e.g. if a valid descriptor is visible to the device in a stale cache line.) Fix this by ensuring that the DMA snoop bit corresponds with the behaviour of the DMA API. Since the driver currently only supports DT, use of_dma_is_coherent(). Note that device_get_dma_attr() can not be used as that risks re-introducing this bug if/when the driver is converted to ACPI. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-11mmc: sdhci: improve ADMA error reportingRussell King1-5/+10
commit d1c536e3177390da43d99f20143b810c35433d1f upstream. ADMA errors are potentially data corrupting events; although we print the register state, we do not usefully print the ADMA descriptors. Worse than that, we print them by referencing their virtual address which is meaningless when the register state gives us the DMA address of the failing descriptor. Print the ADMA descriptors giving their DMA addresses rather than their virtual addresses, and print them using SDHCI_DUMP() rather than DBG(). We also do not show the correct value of the interrupt status register; the register dump shows the current value, after we have cleared the pending interrupts we are going to service. What is more useful is to print the interrupts that _were_ pending at the time the ADMA error was encountered. Fix that too. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-05mmc: sdhci: Fix incorrect switch to HS modeAl Cooper1-1/+3
[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ] When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode. This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set. The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode. This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-09-06mmc: sdhci-of-at91: add quirk for broken HS200Eugen Hristev1-0/+3
commit 7871aa60ae0086fe4626abdf5ed13eeddf306c61 upstream. HS200 is not implemented in the driver, but the controller claims it through caps. Remove it via a quirk, to make sure the mmc core do not try to enable HS200, as it causes the eMMC initialization to fail. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-25mmc: sdhci-of-arasan: Do now show error message in case of deffered probeMichal Simek1-1/+2
commit 60208a267208c27fa3f23dfd36cbda180471fa98 upstream. When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return -EPROBE_DEFER because driver for power sequence provider is not probed yet. Do not show error message when this situation happens. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-16mmc: cavium: Add the missing dma unmap when the dma has finished.Kevin Hao1-0/+1
commit b803974a86039913d5280add083d730b2b9ed8ec upstream. This fixes the below calltrace when the CONFIG_DMA_API_DEBUG is enabled. DMA-API: thunderx_mmc 0000:01:01.4: cpu touching an active dma mapped cacheline [cln=0x000000002fdf9800] WARNING: CPU: 21 PID: 1 at kernel/dma/debug.c:596 debug_dma_assert_idle+0x1f8/0x270 Modules linked in: CPU: 21 PID: 1 Comm: init Not tainted 5.3.0-rc1-next-20190725-yocto-standard+ #64 Hardware name: Marvell OcteonTX CN96XX board (DT) pstate: 80400009 (Nzcv daif +PAN -UAO) pc : debug_dma_assert_idle+0x1f8/0x270 lr : debug_dma_assert_idle+0x1f8/0x270 sp : ffff0000113cfc10 x29: ffff0000113cfc10 x28: 0000ffff8c880000 x27: ffff800bc72a0000 x26: ffff000010ff8000 x25: ffff000010ff8940 x24: ffff000010ff8968 x23: 0000000000000000 x22: ffff000010e83700 x21: ffff000010ea2000 x20: ffff000010e835c8 x19: ffff800bc2c73300 x18: ffffffffffffffff x17: 0000000000000000 x16: 0000000000000000 x15: ffff000010e835c8 x14: 6d20616d64206576 x13: 69746361206e6120 x12: 676e696863756f74 x11: 20757063203a342e x10: 31303a31303a3030 x9 : 303020636d6d5f78 x8 : 3230303030303030 x7 : 00000000000002fd x6 : ffff000010fd57d0 x5 : 0000000000000000 x4 : ffff0000106c5210 x3 : 00000000ffffffff x2 : 0000800bee9c0000 x1 : 57d5843f4aa62800 x0 : 0000000000000000 Call trace: debug_dma_assert_idle+0x1f8/0x270 wp_page_copy+0xb0/0x688 do_wp_page+0xa8/0x5b8 __handle_mm_fault+0x600/0xd00 handle_mm_fault+0x118/0x1e8 do_page_fault+0x200/0x500 do_mem_abort+0x50/0xb0 el0_da+0x20/0x24 ---[ end trace a005534bd23e109f ]--- DMA-API: Mapped at: debug_dma_map_sg+0x94/0x350 cvm_mmc_request+0x3c4/0x988 __mmc_start_request+0x9c/0x1f8 mmc_start_request+0x7c/0xb0 mmc_blk_mq_issue_rq+0x5c4/0x7b8 Signed-off-by: Kevin Hao <haokexin@gmail.com> Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-16mmc: cavium: Set the correct dma max segment size for mmc_hostKevin Hao1-1/+2
commit fa25eba6993b3750f417baabba169afaba076178 upstream. We have set the mmc_host.max_seg_size to 8M, but the dma max segment size of PCI device is set to 64K by default in function pci_device_add(). The mmc_host.max_seg_size is used to set the max segment size of the blk queue. Then this mismatch will trigger a calltrace like below when a bigger than 64K segment request arrives at mmc dev. So we should consider the limitation of the cvm_mmc_host when setting the mmc_host.max_seg_size. DMA-API: thunderx_mmc 0000:01:01.4: mapping sg segment longer than device claims to support [len=131072] [max=65536] WARNING: CPU: 6 PID: 238 at kernel/dma/debug.c:1221 debug_dma_map_sg+0x2b8/0x350 Modules linked in: CPU: 6 PID: 238 Comm: kworker/6:1H Not tainted 5.3.0-rc1-next-20190724-yocto-standard+ #62 Hardware name: Marvell OcteonTX CN96XX board (DT) Workqueue: kblockd blk_mq_run_work_fn pstate: 80c00009 (Nzcv daif +PAN +UAO) pc : debug_dma_map_sg+0x2b8/0x350 lr : debug_dma_map_sg+0x2b8/0x350 sp : ffff00001770f9e0 x29: ffff00001770f9e0 x28: ffffffff00000000 x27: 00000000ffffffff x26: ffff800bc2c73180 x25: ffff000010e83700 x24: 0000000000000002 x23: 0000000000000001 x22: 0000000000000001 x21: 0000000000000000 x20: ffff800bc48ba0b0 x19: ffff800bc97e8c00 x18: ffffffffffffffff x17: 0000000000000000 x16: 0000000000000000 x15: ffff000010e835c8 x14: 6874207265676e6f x13: 6c20746e656d6765 x12: 7320677320676e69 x11: 7070616d203a342e x10: 31303a31303a3030 x9 : 303020636d6d5f78 x8 : 35363d78616d5b20 x7 : 00000000000002fd x6 : ffff000010fd57dc x5 : 0000000000000000 x4 : ffff0000106c61f0 x3 : 00000000ffffffff x2 : 0000800bee060000 x1 : 7010678df3041a00 x0 : 0000000000000000 Call trace: debug_dma_map_sg+0x2b8/0x350 cvm_mmc_request+0x3c4/0x988 __mmc_start_request+0x9c/0x1f8 mmc_start_request+0x7c/0xb0 mmc_blk_mq_issue_rq+0x5c4/0x7b8 mmc_mq_queue_rq+0x11c/0x278 blk_mq_dispatch_rq_list+0xb0/0x568 blk_mq_do_dispatch_sched+0x6c/0x108 blk_mq_sched_dispatch_requests+0x110/0x1b8 __blk_mq_run_hw_queue+0xb0/0x118 blk_mq_run_work_fn+0x28/0x38 process_one_work+0x210/0x490 worker_thread+0x48/0x458 kthread+0x130/0x138 ret_from_fork+0x10/0x1c Signed-off-by: Kevin Hao <haokexin@gmail.com> Fixes: ba3869ff32e4 ("mmc: cavium: Add core MMC driver for Cavium SOCs") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-06mmc: dw_mmc: Fix occasional hang after tuning on eMMCDouglas Anderson1-2/+1
commit ba2d139b02ba684c6c101de42fed782d6cd2b997 upstream. In commit 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") we fixed a tuning-induced hang that I saw when stress testing tuning on certain SD cards. I won't re-hash that whole commit, but the summary is that as a normal part of tuning you need to deal with transfer errors and there were cases where these transfer errors was putting my system into a bad state causing all future transfers to fail. That commit fixed handling of the transfer errors for me. In downstream Chrome OS my fix landed and had the same behavior for all SD/MMC commands. However, it looks like when the commit landed upstream we limited it to only SD tuning commands. Presumably this was to try to get around problems that Alim Akhtar reported on exynos [1]. Unfortunately while stress testing reboots (and suspend/resume) on some rk3288-based Chromebooks I found the same problem on the eMMC on some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC tuning command is different (MMC_SEND_TUNING_BLOCK_HS200 vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the same situation. I'm hoping that whatever problems exynos was having in the past are somehow magically fixed now and we can make the behavior the same for all commands. [1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com Fixes: 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Alim Akhtar <alim.akhtar@gmail.com> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-15mmc: mmci: Prevent polling for busy detection in IRQ contextLudovic Barre1-2/+3
[ Upstream commit 8520ce1e17799b220ff421d4f39438c9c572ade3 ] The IRQ handler, mmci_irq(), loops until all status bits have been cleared. However, the status bit signaling busy in variant->busy_detect_flag, may be set even if busy detection isn't monitored for the current request. This may be the case for the CMD11 when switching the I/O voltage, which leads to that mmci_irq() busy loops in IRQ context. Fix this problem, by clearing the status bit for busy, before continuing to validate the condition for the loop. This is safe, because the busy status detection has already been taken care of by mmci_cmd_irq(). Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 supportYinbo Zhu1-1/+3
[ Upstream commit 05cb6b2a66fa7837211a060878e91be5eb10cb07 ] eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock), and 0xC(2^25 SD clock). The data timeout counter can count from 2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout counter counts for only 2^13 SD clocks. A-008358: The data timeout counter value loaded into the timeout counter is less than expected and can result into early timeout error in case of eSDHC data transactions. The table below shows the expected vs actual timeout period for different values of SYSCTL[DTOCV]: these two erratum has the same quirk to control it, and set SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: sdhci-of-esdhc: add erratum A-009204 supportYinbo Zhu1-0/+3
[ Upstream commit 5dd195522562542bc6ebe6e7bd47890d8b7ca93c ] In the event of that any data error (like, IRQSTAT[DCE]) occurs during an eSDHC data transaction where DMA is used for data transfer to/from the system memory, setting the SYSCTL[RSTD] register may cause a system hang. If software sets the register SYSCTL[RSTD] to 1 for error recovery while DMA transferring is not complete, eSDHC may hang the system bus. This happens because the software register SYSCTL[RSTD] resets the DMA engine without waiting for the completion of pending system transactions. This erratum is to fix this issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: sdhci-of-esdhc: add erratum eSDHC5 supportYinbo Zhu1-0/+3
[ Upstream commit a46e42712596b51874f04c73f1cdf1017f88df52 ] Software writing to the Transfer Type configuration register (system clock domain) can cause a setup/hold violation in the CRC flops (card clock domain), which can cause write accesses to be sent with corrupt CRC values. This issue occurs only for write preceded by read. this erratum is to fix this issue. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc_spi: add a status check for spi_sync_lockedKangjie Lu1-0/+4
[ Upstream commit 611025983b7976df0183390a63a2166411d177f1 ] In case spi_sync_locked fails, the fix reports the error and returns the error code upstream. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-05-31mmc: sdhci-iproc: Set NO_HISPD bit to fix HS50 data hold time problemTrac Hoang1-1/+2
commit ec0970e0a1b2c807c908d459641a9f9a1be3e130 upstream. The iproc host eMMC/SD controller hold time does not meet the specification in the HS50 mode. This problem can be mitigated by disabling the HISPD bit; thus forcing the controller output data to be driven on the falling clock edges rather than the rising clock edges. Stable tag (v4.12+) chosen to assist stable kernel maintainers so that the change does not produce merge conflicts backporting to older kernel versions. In reality, the timing bug existed since the driver was first introduced but there is no need for this driver to be supported in kernel versions that old. Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Trac Hoang <trac.hoang@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-31mmc: sdhci-iproc: cygnus: Set NO_HISPD bit to fix HS50 data hold time problemTrac Hoang1-1/+2
commit b7dfa695afc40d5396ed84b9f25aa3754de23e39 upstream. The iproc host eMMC/SD controller hold time does not meet the specification in the HS50 mode. This problem can be mitigated by disabling the HISPD bit; thus forcing the controller output data to be driven on the falling clock edges rather than the rising clock edges. This change applies only to the Cygnus platform. Stable tag (v4.12+) chosen to assist stable kernel maintainers so that the change does not produce merge conflicts backporting to older kernel versions. In reality, the timing bug existed since the driver was first introduced but there is no need for this driver to be supported in kernel versions that old. Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Trac Hoang <trac.hoang@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-14x86/cpu: Sanitize FAM6_ATOM namingPeter Zijlstra1-1/+1
commit f2c4db1bd80720cd8cb2a5aa220d9bc9f374f04e upstream Going primarily by: https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors with additional information gleaned from other related pages; notably: - Bonnell shrink was called Saltwell - Moorefield is the Merriefield refresh which makes it Airmont The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE for i in `git grep -l FAM6_ATOM` ; do sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \ -e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \ -e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \ -e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \ -e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \ -e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \ -e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \ -e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \ -e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \ -e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \ -e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i} done Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: dave.hansen@linux.intel.com Cc: len.brown@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27mmc: sdhci: Handle auto-command errorsAdrian Hunter2-1/+41
[ Upstream commit af849c86109d79222e549826068bbf4e7f9a2472 ] If the host controller supports auto-commands then enable the auto-command error interrupt and handle it. In the case of auto-CMD23, the error is treated the same as manual CMD23 error. In the case of auto-CMD12, commands-during-transfer are not permitted, so the error handling is treated the same as a data error. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-27mmc: sdhci: Rename SDHCI_ACMD12_ERR and SDHCI_INT_ACMD12ERRAdrian Hunter3-10/+10
[ Upstream commit 869f8a69bb3a4aec4eb914a330d4ba53a9eed495 ] The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12 errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-27mmc: sdhci: Fix data command CRC error handlingAdrian Hunter1-25/+15
[ Upstream commit 4bf780996669280171c9cd58196512849b93434e ] Existing data command CRC error handling is non-standard and does not work with some Intel host controllers. Specifically, the assumption that the host controller will continue operating normally after the error interrupt, is not valid. Change the driver to handle the error in the same manner as a data CRC error, taking care to ensure that the data line reset is done for single or multi-block transfers, and it is done before unmapping DMA. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-20mmc: davinci: remove extraneous __init annotationArnd Bergmann1-1/+1
[ Upstream commit 9ce58dd7d9da3ca0d7cb8c9568f1c6f4746da65a ] Building with clang finds a mistaken __init tag: WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host() The function davinci_mmcsd_probe() references the function __init init_mmcsd_host(). This is often because davinci_mmcsd_probe lacks a __init annotation or the annotation of init_mmcsd_host is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-04-05mmc: omap: fix the maximum timeout settingAaro Koskinen1-1/+1
[ Upstream commit a6327b5e57fdc679c842588c3be046c0b39cc127 ] When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy: MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! [ad inf.] Emulator warnings appear to be valid. The TI document SPRU680 [1] ("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card (MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253 cycles and "0xff and 0xfe cannot be used". Fix by using 0xfd as the maximum timeout. Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810 (OMAP2420) that MMC works as before. [1] http://www.ti.com/lit/ug/spru680/spru680.pdf Fixes: 730c9b7e6630f ("[MMC] Add OMAP MMC host driver") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-03-27mmc: pxamci: fix enum type confusionArnd Bergmann1-1/+1
commit e60a582bcde01158a64ff948fb799f21f5d31a11 upstream. clang points out several instances of mismatched types in this drivers, all coming from a single declaration: drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion] direction = DMA_DEV_TO_MEM; ~ ^~~~~~~~~~~~~~ drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion] tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction, The behavior is correct, so this must be a simply typo from dma_data_direction and dma_transfer_direction being similarly named types with a similar purpose. Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-23mmc: sdhci-esdhc-imx: fix HS400 timing issueBOUGH CHEN1-0/+1
commit de0a0decf2edfc5b0c782915f4120cf990a9bd13 upstream. Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/ MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS, we can not do tuning reset, otherwise HS400 timing is not right. Here is the process of init HS400, first finish tuning in HS200 mode, then switch to HS mode and 8 bit DDR mode, finally switch to HS400 mode. If we do tuning reset in HS mode, this will cause HS400 mode lost the tuning setting, which will cause CRC error. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.12+ Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-05mmc: sdhci-esdhc-imx: correct the fix of ERR004536BOUGH CHEN1-4/+5
commit e30be063d6dbcc0f18b1eb25fa709fdef89201fb upstream. Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") involve the fix of ERR004536, but the fix is incorrect. Double confirm with IC, need to clear the bit 7 of register 0x6c rather than set this bit 7. Here is the definition of bit 7 of 0x6c: 0: enable the new IC fix for ERR004536 1: do not use the IC fix, keep the same as before Find this issue on i.MX845s-evk board when enable CMDQ, and let system in heavy loading. root@imx8mmevk:~# dd if=/dev/mmcblk2 of=/dev/null bs=1M & root@imx8mmevk:~# memtester 1000M > /dev/zero & root@imx8mmevk:~# [ 139.897220] mmc2: cqhci: timeout for tag 16 [ 139.901417] mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== [ 139.907862] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 [ 139.914311] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000000 [ 139.920753] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 [ 139.927193] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 [ 139.933634] mmc2: cqhci: TDL base: 0x7809c000 | TDL up32: 0x00000000 [ 139.940073] mmc2: cqhci: Doorbell: 0x00030000 | TCN: 0x00000000 [ 139.946518] mmc2: cqhci: Dev queue: 0x00010000 | Dev Pend: 0x00010000 [ 139.952967] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 [ 139.959411] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000 [ 139.965857] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 [ 139.972308] mmc2: cqhci: Resp idx: 0x0000002e | Resp arg: 0x00000900 [ 139.978761] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 139.985214] mmc2: sdhci: Sys addr: 0xb2c19000 | Version: 0x00000002 [ 139.991669] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000400 [ 139.998127] mmc2: sdhci: Argument: 0x40110400 | Trn mode: 0x00000033 [ 140.004618] mmc2: sdhci: Present: 0x01088a8f | Host ctl: 0x00000030 [ 140.011113] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 [ 140.017583] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f [ 140.024039] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 [ 140.030497] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 [ 140.036972] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502 [ 140.043426] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 [ 140.049867] mmc2: sdhci: Cmd: 0x00002c1a | Max curr: 0x00ffffff [ 140.056314] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0xffffffff [ 140.062755] mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d00f00 [ 140.069195] mmc2: sdhci: Host ctl2: 0x00000008 [ 140.073640] mmc2: sdhci: ADMA Err: 0x00000007 | ADMA Ptr: 0x7809c108 [ 140.080079] mmc2: sdhci: ============================================ [ 140.086662] mmc2: running CQE recovery Fixes: 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-05mmc: tmio: fix access width of Block Count RegisterTakeshi Saito3-1/+11
commit 5603731a15ef9ca317c122cc8c959f1dee1798b4 upstream. In R-Car Gen2 or later, the maximum number of transfer blocks are changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register should use iowrite32(). If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this value will not be cleared. So, SD/MMC card initialization fails. So, check for the bigger register and use apropriate write. Also, mark the register as extended on Gen2. Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> [wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au> [Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-05mmc: tmio_mmc_core: don't claim spurious interruptsSergei Shtylyov1-4/+7
commit 5c27ff5db1491a947264d6d4e4cbe43ae6535bae upstream. I have encountered an interrupt storm during the eMMC chip probing (and the chip finally didn't get detected). It turned out that U-Boot left the DMAC interrupts enabled while the Linux driver didn't use those. The SDHI driver's interrupt handler somehow assumes that, even if an SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think that if none of the enabled interrupts happened and got handled, we should return IRQ_NONE -- that way the kernel IRQ code recoginizes a spurious interrupt and masks it off pretty quickly... Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-05mmc: spi: Fix card detection during probeJonathan Neuschäfer1-0/+1
commit c9bd505dbd9d3dc80c496f88eafe70affdcf1ba6 upstream. When using the mmc_spi driver with a card-detect pin, I noticed that the card was not detected immediately after probe, but only after it was unplugged and plugged back in (and the CD IRQ fired). The call tree looks something like this: mmc_spi_probe mmc_add_host mmc_start_host _mmc_detect_change mmc_schedule_delayed_work(&host->detect, 0) mmc_rescan host->bus_ops->detect(host) mmc_detect _mmc_detect_card_removed host->ops->get_cd(host) mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set) mmc_gpiod_request_cd ctx->cd_gpio = desc To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ is registered. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12mmc: sdhci-xenon: Fix timeout checksAdrian Hunter2-6/+14
[ Upstream commit 0e6e7c2ff397e1bbebc882ca3132148aaaef1ddd ] Always check the wait condition before returning timeout. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Zhoujie Wu <zjwu@marvell.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12mmc: sdhci-of-esdhc: Fix timeout checksAdrian Hunter1-4/+12
[ Upstream commit ea6d027312111c6d96309ad1a684b33cb37e6764 ] Always check the wait condition before returning timeout. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12mmc: bcm2835: reset host on timeoutMichal Suchanek1-0/+3
[ Upstream commit f6000a4eb34e6462bc0dd39809c1bb99f9633269 ] The bcm2835 mmc host tends to lock up for unknown reason so reset it on timeout. The upper mmc block layer tries retransimitting with single blocks which tends to work out after a long wait. This is better than giving up and leaving the machine broken for no obvious reason. Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-12mmc: bcm2835: Recover from MMC_SEND_EXT_CSDPhil Elwell1-0/+9
[ Upstream commit 07d405769afea5718529fc9e341f0b13b3189b6f ] If the user issues an "mmc extcsd read", the SD controller receives what it thinks is a SEND_IF_COND command with an unexpected data block. The resulting operations leave the FSM stuck in READWAIT, a state which persists until the MMC framework resets the controller, by which point the root filesystem is likely to have been unmounted. A less heavyweight solution is to detect the condition and nudge the FSM by asserting the (self-clearing) FORCE_DATA_MODE bit. Link: https://github.com/raspberrypi/linux/issues/2728 Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-06mmc: sdhci-iproc: handle mmc_of_parse() errors during probeStefan Wahren1-1/+4
commit 2bd44dadd5bfb4135162322fd0b45a174d4ad5bf upstream. We need to handle mmc_of_parse() errors during probe. This finally fixes the wifi regression on Raspberry Pi 3 series. In error case the wifi chip was permanently in reset because of the power sequence depending on the deferred probe of the GPIO expander. Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver") Cc: stable@vger.kernel.org Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-06mmc: bcm2835: Fix DMA channel leak on probe errorLukas Wunner1-0/+2
commit 8c9620b1cc9b69e82fa8d4081d646d0016b602e7 upstream. The BCM2835 MMC host driver requests a DMA channel on probe but neglects to release the channel in the probe error path. The channel may therefore be leaked, in particular if devm_clk_get() causes probe deferral. Fix it. Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.12+ Cc: Frank Pavlic <f.pavlic@kunbus.de> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-25 08:09:28 +0300