summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/mmci.c
AgeCommit message (Collapse)AuthorFilesLines
2012-01-20ARM: 7221/1: mmc: mmci: Change from using legacy suspendUlf Hansson1-10/+12
This patch switch from using the legacy suspend/resume to the new way of registering PM callbacks. No functional change is done. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-20ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handlerUlf Hansson1-4/+4
The purpose of the vdd_handler does not make sense. We remove it and use a generic approach instead. A new ios_handler is added, the purpose of which e.g. can be to control GPIO pins to a levelshifter. Previously the vdd_handler was also used for making additional changes to the power register bits. This option is superfluous and is therefore removed. Adaptaptions from the old vdd_handler to the new ios_handler is done for mach-ux500 board, which was the only one using the vdd_handler. This patch is based upon a patch from Sebastian Rasmussen. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-20ARM: 7218/1: mmc: mmci: Provide option to configure bus signal directionUlf Hansson1-0/+21
The ST Micro variant supports bus signal direction indication. A new member in the variant struct is added for this. Moreover the actual signal direction configuration is board specific, thus the amba mmci platform data is extended with a new member to be able provide mmci with these specific board configurations. This patch is based upon a patch from Sebastian Rasmussen. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-20ARM: 7217/1: mmc: mmci: Put power register deviations in variant dataUlf Hansson1-5/+17
Use variant data to store hardware controller deviations concerning power registers to improve readability of the code. Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Tested-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-20ARM: 7216/1: mmc: mmci: Do not release spinlock in request_endUlf Hansson1-6/+0
The patch "mmc: core: move ->request() call from atomic context", is the reason to why this change is possible. This simplifies the error handling code execution path quite a lot and potentially also fixes some error handling hang problems. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2012-01-18Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds1-4/+7
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits) ARM: mach-shmobile: specify CHCLR registers on SH7372 dma: shdma: fix runtime PM: clear channel buffers on reset dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit dmaengine/ste_dma40: clear LNK on channel startup dmaengine: intel_mid_dma: remove legacy pm interface ASoC: mxs: correct 'direction' of device_prep_dma_cyclic dmaengine: intel_mid_dma: error path fix dmaengine: intel_mid_dma: locking and freeing fixes mtd: gpmi-nand: move to dma_transfer_direction mtd: fix compile error for gpmi-nand mmc: mxs-mmc: fix the dma_transfer_direction migration dmaengine: add DMA_TRANS_NONE to dma_transfer_direction dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled. dma: mxs-dma: fix a typo in comment DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove video i.MX IPU: Fix display connections i.MX IPU DMA: Fix wrong burstsize settings dmaengine/ste_dma40: allow fixed physical channel ... Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c} The conflicts looked pretty trivial, but I'll ask people to verify them.
2012-01-14Merge tag 'mmc-merge-for-3.3-rc1' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc MMC highlights for 3.3: Core: * Support for the HS200 high-speed eMMC mode. * Support SDIO 3.0 Ultra High Speed cards. * Kill pending block requests immediately if card is removed. * Enable the eMMC feature for locking boot partitions read-only until next power on, exposed via sysfs. Drivers: * Runtime PM support for Intel Medfield SDIO. * Suspend/resume support for sdhci-spear. * sh-mmcif now processes requests asynchronously. * tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits) mmc: fix a deadlock between system suspend and MMC block IO mmc: sdhci: restore the enabled dma when do reset all mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation mmc: host: Adds support for eMMC 4.5 HS200 mode mmc: core: HS200 mode support for eMMC 4.5 mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT() mmc: core: Separate the timeout value for cache-ctrl mmc: sdhci-spear: Fix compilation error mmc: sdhci: Deal with failure case in sdhci_suspend_host mmc: dw_mmc: Clear the DDR mode for non-DDR mmc: sd: Fix SDR12 timing regression mmc: sdhci: Fix tuning timer incorrect setting when suspending host mmc: core: Add option to prevent eMMC sleep command mmc: omap_hsmmc: use threaded irq handler for card-detect. mmc: sdhci-pci: enable runtime PM for Medfield SDIO mmc: sdhci: Always pass clock request value zero to set_clock host op mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION mmc: sdhci-pci: get gpio numbers from platform data mmc: sdhci-pci: add platform data mmc: sdhci: prevent card detection activity for non-removable cards ...
2012-01-12mmc: mmci: add capabilities2 for MMC_CAP2Per Forlin1-0/+1
Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-07Merge branch 'amba-modalias' of ↵Linus Torvalds1-0/+2
git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm * 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: sound: aaci: Enable module alias autogeneration for AMBA drivers watchdog: sp805: Enable module alias autogeneration for AMBA drivers fbdev: amba: Enable module alias autogeneration for AMBA drivers serial: pl011: Enable module alias autogeneration for AMBA drivers serial: pl010: Enable module alias autogeneration for AMBA drivers spi: pl022: Enable module alias autogeneration for AMBA drivers rtc: pl031: Enable module alias autogeneration for AMBA drivers rtc: pl030: Enable module alias autogeneration for AMBA drivers mmc: mmci: Enable module alias autogeneration for AMBA drivers input: ambakmi: Enable module alias autogeneration for AMBA drivers gpio: pl061: Enable module alias autogeneration for AMBA drivers dmaengine: pl330: Enable module alias autogeneration for AMBA drivers dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers hwrng: nomadik: Enable module alias autogeneration for AMBA drivers ARM: amba: Auto-generate AMBA driver module aliases during modpost ARM: amba: Move definition of struct amba_id to mod_devicetable.h
2011-12-19ARM: 7220/1: mmc: mmci: Fixup error handling for dmaUlf Hansson1-1/+5
When getting a cmd irq during an ongoing data transfer with dma, the dma job were never terminated. This is now corrected. Cc: <stable@vger.kernel.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-12-19ARM: 7214/1: mmc: mmci: Fixup handling of MCI_STARTBITERRUlf Hansson1-3/+5
The interrupt was previously enabled and then correctly cleared. Now we also handle it correctly. Cc: <stable@vger.kernel.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-11-22mmc: mmci: Enable module alias autogeneration for AMBA driversDave Martin1-0/+2
Signed-off-by: Dave Martin <dave.martin@linaro.org>
2011-11-17Merge branch 'dma_slave_direction' into next_test_dirnVinod Koul1-4/+7
resolved conflicts: drivers/media/video/mx3_camera.c
2011-10-31mmc-host: move to dma_transfer_directionVinod Koul1-4/+7
fixup usage of dma direction by introducing dma_transfer_direction, this patch moves mmc drivers to use new enum Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Chris Ball <cjb@laptop.org> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2011-10-29Merge branch 'for-linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits) mmc: fix compile error when CONFIG_BLOCK is not enabled mmc: core: Cleanup eMMC4.5 conditionals mmc: omap_hsmmc: if multiblock reads are broken, disable them mmc: core: add workaround for controllers with broken multiblock reads mmc: core: Prevent too long response times for suspend mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00 mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode mmc: core: support HPI send command mmc: core: Add cache control for eMMC4.5 device mmc: core: Modify the timeout value for writing power class mmc: core: new discard feature support at eMMC v4.5 mmc: core: mmc sanitize feature support for v4.5 mmc: dw_mmc: modify DATA register offset mmc: sdhci-pci: add flag for devices that can support runtime PM mmc: omap_hsmmc: ensure pbias configuration is always done mmc: core: Add Power Off Notify Feature eMMC 4.5 mmc: sdhci-s3c: fix potential NULL dereference mmc: replace printk with appropriate display macro mmc: core: Add default timeout value for CMD6 mmc: sdhci-pci: add runtime pm support ...
2011-10-27mmc: replace printk with appropriate display macroGirish K S1-1/+1
All the files using printk function for displaying kernel messages in the mmc driver have been replaced with corresponding macro. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-27mmc: mmci: simplify err check in mmci_post_requestPer Forlin1-1/+1
The error condition indicates that mmci_post_request() should cleanup after the mmci_pre_request(). In this case the resources allocated by device_prep_slave_sg() are freed by calling dmaengine_terminate_all(). dma_unmap_sg() should always be performed if the host_cookie is set. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-09-27clk: mmci: convert to clk_prepare()/clk_unprepare()Russell King1-1/+8
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-22PM: add runtime PM support to MMCIRussell King1-0/+12
Add runtime PM support to the MMCI primecell driver, making use of the core primecell bus runtime PM support. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-07-24Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds1-1/+9
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits) ARM: 7004/1: fix traps.h compile warnings ARM: 6998/2: kernel: use proper memory barriers for bitops ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM ARM: Fix build errors caused by adding generic macros ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU ARM: CPU hotplug: pass in proper affinity mask on IRQ migration ARM: GIC: avoid routing interrupts to offline CPUs ARM: CPU hotplug: fix abuse of irqdesc->node ARM: 6981/2: mmci: adjust calculation of f_min ARM: 7000/1: LPAE: Use long long printk format for displaying the pud ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence ARM: ARM_DMA_ZONE_SIZE is no more ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ...
2011-07-23Merge branches 'btc', 'dma', 'entry', 'fixes', 'linker-layout', 'misc', ↵Russell King1-1/+11
'mmci', 'suspend' and 'vfp' into for-next
2011-07-21mmc: mmci: implement pre_req() and post_req()Per Forlin1-13/+134
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next mmc data transfer. post_req() runs dma_unmap_sg. If not calling pre_req() before mmci_request(), mmci_request() will prepare the cache and dma just like it did it before. It is optional to use pre_req() and post_req() for mmci. Signed-off-by: Per Forlin <per.forlin@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-19ARM: 6981/2: mmci: adjust calculation of f_minLinus Walleij1-1/+9
The ARM version maximum clock divider is 512 whereas for the ST variants it's 257. Let's use DIV_ROUND_UP() for both cases so we can see clearly what's going on here. [Use DIV_ROUND_UP to clarify elder code] Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-07-06ARM: 6980/1: mmci: use StartBitErr to detect bad connectionsLinus Walleij1-0/+2
Stresstesting insert/remove of SD-cards can trigger a StartBitErr. This made the driver to hang in forever waiting for a non ocurring data timeout. This bit and interrupt is documented in the original PL180 TRM, just never implemented until now. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Reviewed-by: Linus Walleij <linus.walleij@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-06ARM: 6894/1: mmci: trigger card detect IRQs on falling and rising edgesLinus Walleij1-2/+10
Right now the card detect IRQ for MMCI is requested without any flags which will give some default machine-specified IRQ behaviour. However on the U300 rising+falling edges (such as can be expected from a simple GPIO to generate when inserting/removing a card) need to be requested explicitly. Cc: Rabin Vincent <rabin.vincent@stericsson.com> Cc: Ulf Hansson <ulf.hansson@stericsson.com> Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-26ARM: 6832/1: mmci: support for ST-Ericsson db8500v2Philippe Langlais1-2/+23
ST-Ericsson modified ARM PrimeCell PL180 block has not got an updated corresponding amba-id, althought the IP block has changed in db8500v2. The change was done to the datactrl register. Using the overrided subversion ID, account for this. Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-12ARM: 6858/1: mmci: force negative edge on clock bypass for ux500Linus Walleij1-0/+2
This fixes a regression on high clock speeds with the MMCI on ux500. We need to make sure we derive the passthru clock on the falling edge of the incoming clock if it shall work at high frequencies, and on the ux500's there is a special bit for this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-11ARM: 6785/1: mmci: separate out ST Micro register definesLinus Walleij1-2/+2
The mmci.h header contained a few registers not clearly marked as ST Micro only, rectify this and remove the HWFC magic in the process. The idea is to make the mmci.h header file more ordered so other vendors with PL180 derivates can see where to put in their custom register defines. Includes portions of an earlier patch from Sebastian Rasmussen. Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-03-25mmc: mmci: Add ARM variant with extended FIFOPawel Moll1-1/+12
New IO FPGA implementation for Versatile Express boards contain MMCI (PL180) cell with FIFO extended to 128 words (512 bytes). Matt Waddel reports that this patch improves MMC performance on his vexpress system, and also fixes "mmcblk0: error -5 transferring data" errors. Signed-off-by: Pawel Moll <pawel.moll@arm.com> Tested-by: Matt Waddel <matt.waddel@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-17Merge branches 'aaci', 'mmci-dma', 'pl' and 'pl011' into driversRussell King1-121/+322
2011-02-23ARM: amba: make probe() functions take const id tablesRussell King1-1/+2
Make Primecell driver probe functions take a const pointer to their ID tables. Drivers should never modify their ID tables in their probe handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: add dmaengine-based DMA supportRussell King1-8/+274
Based on a patch from Linus Walleij. Add dmaengine based support for DMA to the MMCI driver, using the Primecell DMA engine interface. The changes over Linus' driver are: - rename txsize_threshold to dmasize_threshold, as this reflects the purpose more. - use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'. - clean up requesting of dma channels. - don't release a single channel twice when it's shared between tx and rx. - get rid of 'dma_enable' bool - instead check whether the channel is NULL. - detect incomplete DMA at the end of a transfer. Some DMA controllers (eg, PL08x) are unable to be configured for scatter DMA and also listen to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI. They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the final burst/words, PL08x does not transfer the last few words. - map and unmap DMA buffers using the DMA engine struct device, not the MMCI struct device - the DMA engine is doing the DMA transfer, not us. - avoid double-unmapping of the DMA buffers on MMCI data errors. - don't check for negative values from the dmaengine tx submission function - Dan says this must never fail. - use new dmaengine helper functions rather than using the ugly function pointers directly. - allow DMA code to be fully optimized away using dma_inprogress() which is defined to constant 0 if DMA engine support is disabled. - request maximum segment size from the DMA engine struct device and set this appropriately. - removed checking of buffer alignment - the DMA engine should deal with its own restrictions on buffer alignment, not the individual DMA engine users. - removed setting DMAREQCTL - this confuses some DMA controllers as it causes LBREQ to be asserted for the last seven transfers, rather than six SREQ and one LSREQ. - removed burst setting - the DMA controller should not burst past the transfer size required to complete the DMA operation. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: no need for separate host->data_xferedRussell King1-6/+3
We don't need to store the number of bytes transferred in our host structure - we can store this directly in data->bytes_xfered. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: avoid unnecessary switch to data available PIO interruptsRussell King1-6/+7
We don't need to switch to data available interrupts if there's at least half a FIFO depth worth of data remaining, as we'll still get the FIFO half full interrupt. Keep this interrupt masked off until we have less than half the FIFO depth worth of data remaining. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: no need to call flush_dcache_page() with sg_miter APIRussell King1-19/+0
The sg_miter API provides the required cache maintainence, so we don't need to do that ourselves. Remove the unnecessary additional cache maintainence. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: avoid reporting too many completed bytes on fifo overrunRussell King1-6/+18
The data counter counts the number of bytes transferred on the MMC bus. When a FIFO overrun occurs, we will not have transferred a FIFOs-worth of data to memory, and so the data counter will be a FIFOs-worth ahead. If this occurs on a block boundary, we will report one too many sectors as successful. Fix this. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-31ARM: mmci: round down the bytes transferred on errorRussell King1-3/+4
We should not report incomplete blocks on error. Return the number of bytes successfully transferred, rounded down to the nearest block. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-31ARM: mmci: complete the transaction on errorRussell King1-1/+1
When we encounter an error, make sure we complete the transaction otherwise we'll leave the request dangling. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-28ARM: 6642/1: mmci: calculate remaining bytes at error correctlyLinus Walleij1-2/+2
The MMCIDATACNT register contain the number of byte left at error not the number of words, so loose the << 2 thing. Further if CRC fails on the first block, we may end up with a negative number of transferred bytes which is not good, and the formula was in wrong order. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-26mmc: mmci: don't read command response when invalidRussell King - ARM Linux1-5/+5
Don't read the command response from the registers when either the command timed out (because there was no response from the card) or the checksum on the response was invalid. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-24ARM: 6632/3: mmci: stop using the blockend interruptsLinus Walleij1-78/+20
Implement a suggestion from Russell to drop the use of blockend interrupts altogether and instead rely on the data counter. Tested with error-free cards on U300, U8500 and RealView PB1176. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-30ARM: mmci: Clean up MMCI announcement printkRussell King1-4/+4
Make the MMCI announcement printk say which primecell part number has been found. Display the revision as an unsigned decimal, and display only the first 8 hex digits of the base address unless it's larger. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-19ARM: 6530/1: mmci: partially revert clock divisor codeLinus Walleij1-7/+1
I misread the datasheet as if bypass mode was not available at all on the ux500's, I was wrong. It is there, the datasheet just states that you should not have to use it. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-19ARM: 6526/1: mmci: corrected calculation of clock div for ux500Linus Walleij1-1/+26
The Ux500 variant of this block has a different divider. The value used right now is too big and which means a loss in performance. This fix corrects it. Also expand the math comments a bit so it's clear what's happening. Further the Ux500 variant does not like if we use the BYPASS bit, instead we are supposed to set the clock divider to zero. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6438/2: mmci: add SDIO support for ST VariantsLinus Walleij1-1/+36
This adds some minor variant data and trickery to enable SDIO on the ST Micro variants of MMCI/PL180. Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6399/3: mmci: handle broken MCI_DATABLOCKEND hardwareLinus Walleij1-16/+77
On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive out-of-order. Replace an ugly #ifdef hack with a proper runtime solution which models what is really happening. In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND flag isn't properly cleared in hardware following and ACK leading to all kind of weird behaviour when the flag is still up in subsequent interrupts, so we add two flags indicating the error and handle this runtime. Cc: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6311/2: mmci: work with only one irqLinus Walleij1-9/+41
The DBx500 variants have only one IRQ line hooked up. Allow these (and any other implementations which choose to use only one irq) to work by directing the PIO interrupts also to the first IRQ line. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-23mmc: Move regulator handling closer to coreLinus Walleij1-10/+18
After discovering a problem in regulator reference counting I took Mark Brown's advice to move the reference count into the MMC core by making the regulator status a member of struct mmc_host. I took this opportunity to also implement NULL versions of the regulator functions so as to rid the driver code from some ugly #ifdef CONFIG_REGULATOR clauses. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Tony Lindgren <tony@atomide.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Sundar Iyer <sundar.iyer@stericsson.com> Cc: Daniel Mack <daniel@caiaq.de> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Matt Fleming <matt@console-pimps.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Cliff Brake <cbrake@bec-systems.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: Remove distinction between hw and phys segmentsMartin K. Petersen1-2/+1
We have deprecated the distinction between hardware and physical segments in the block layer. Consolidate the two limits into one in drivers/mmc/. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-09-23ARM: 6370/1: mmci: use _cansleep GPIO functionsLinus Walleij1-2/+3
Currently the kernel is screaming about slowpath at me for the wp/cd callbacks. Switch to the _cansleep variants so as to silence this. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-15 22:55:06 +0300