summaryrefslogtreecommitdiff
path: root/drivers/mmc/core
AgeCommit message (Collapse)AuthorFilesLines
2024-06-16mmc: core: Add mmc_gpiod_set_cd_config() functionHans de Goede1-0/+20
commit 63a7cd660246aa36af263b85c33ecc6601bf04be upstream. Some mmc host drivers may need to fixup a card-detection GPIO's config to e.g. enable the GPIO controllers builtin pull-up resistor on devices where the firmware description of the GPIO is broken (e.g. GpioInt with PullNone instead of PullUp in ACPI DSDT). Since this is the exception rather then the rule adding a config parameter to mmc_gpiod_request_cd() seems undesirable, so instead add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper to call gpiod_set_config() on the card-detect GPIO acquired through mmc_gpiod_request_cd(). Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-16mmc: core: Do not force a retune before RPMB switchJorge Ramirez-Ortiz1-2/+1
commit 67380251e8bbd3302c64fea07f95c31971b91c22 upstream. Requesting a retune before switching to the RPMB partition has been observed to cause CRC errors on the RPMB reads (-EILSEQ). Since RPMB reads can not be retried, the clients would be directly affected by the errors. This commit disables the retune request prior to switching to the RPMB partition: mmc_retune_pause() no longer triggers a retune before the pause period begins. This was verified with the sdhci-of-arasan driver (ZynqMP) configured for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both cases, the error was easy to reproduce triggering every few tenths of reads. With this commit, systems that were utilizing OP-TEE to access RPMB variables will experience an enhanced performance. Specifically, when OP-TEE is configured to employ RPMB as a secure storage solution, it not only writes the data but also the secure filesystem within the partition. As a result, retrieving any variable involves multiple RPMB reads, typically around five. For context, on ZynqMP, each retune request consumed approximately 8ms. Consequently, reading any RPMB variable used to take at the very minimum 40ms. After droping the need to retune before switching to the RPMB partition, this is no longer the case. Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Acked-by: Avri Altman <avri.altman@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-13mmc: core: Avoid negative index with array accessMikko Rapeli1-1/+1
commit cf55a7acd1ed38afe43bba1c8a0935b51d1dc014 upstream. Commit 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") assigns prev_idata = idatas[i - 1], but doesn't check that the iterator i is greater than zero. Let's fix this by adding a check. Fixes: 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") Link: https://lore.kernel.org/all/20231129092535.3278-1-avri.altman@wdc.com/ Cc: stable@vger.kernel.org Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org> Reviewed-by: Avri Altman <avri.altman@wdc.com> Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://lore.kernel.org/r/20240313133744.2405325-2-mikko.rapeli@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-13mmc: core: Initialize mmc_blk_ioc_dataMikko Rapeli1-1/+1
commit 0cdfe5b0bf295c0dee97436a8ed13336933a0211 upstream. Commit 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") adds flags uint to struct mmc_blk_ioc_data, but it does not get initialized for RPMB ioctls which now fails. Let's fix this by always initializing the struct and flags to zero. Fixes: 4d0c8d0aef63 ("mmc: core: Use mrq.sbc in close-ended ffu") Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218587 Link: https://lore.kernel.org/all/20231129092535.3278-1-avri.altman@wdc.com/ Cc: stable@vger.kernel.org Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://lore.kernel.org/r/20240313133744.2405325-1-mikko.rapeli@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-13mmc: core: Fix switch on gp3 partitionDominique Martinet1-4/+6
[ Upstream commit 4af59a8df5ea930038cd3355e822f5eedf4accc1 ] Commit e7794c14fd73 ("mmc: rpmb: fixes pause retune on all RPMB partitions.") added a mask check for 'part_type', but the mask used was wrong leading to the code intended for rpmb also being executed for GP3. On some MMCs (but not all) this would make gp3 partition inaccessible: armadillo:~# head -c 1 < /dev/mmcblk2gp3 head: standard input: I/O error armadillo:~# dmesg -c [ 422.976583] mmc2: running CQE recovery [ 423.058182] mmc2: running CQE recovery [ 423.137607] mmc2: running CQE recovery [ 423.137802] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 423.237125] mmc2: running CQE recovery [ 423.318206] mmc2: running CQE recovery [ 423.397680] mmc2: running CQE recovery [ 423.397837] blk_update_request: I/O error, dev mmcblk2gp3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 423.408287] Buffer I/O error on dev mmcblk2gp3, logical block 0, async page read the part_type values of interest here are defined as follow: main 0 boot0 1 boot1 2 rpmb 3 gp0 4 gp1 5 gp2 6 gp3 7 so mask with EXT_CSD_PART_CONFIG_ACC_MASK (7) to correctly identify rpmb Fixes: e7794c14fd73 ("mmc: rpmb: fixes pause retune on all RPMB partitions.") Cc: stable@vger.kernel.org Cc: Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240306-mmc-partswitch-v1-1-bf116985d950@codewreck.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-06mmc: core: Fix eMMC initialization with 1-bit bus connectionIvan Semenov1-0/+2
commit ff3206d2186d84e4f77e1378ba1d225633f17b9b upstream. Initializing an eMMC that's connected via a 1-bit bus is current failing, if the HW (DT) informs that 4-bit bus is supported. In fact this is a regression, as we were earlier capable of falling back to 1-bit mode, when switching to 4/8-bit bus failed. Therefore, let's restore the behaviour. Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin) Before patch: [134509.044225] mmc0: switch to bus width 4 failed [134509.044509] mmc0: new high speed MMC card at address 0001 [134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB [134509.281602] mmc0: switch to bus width 4 failed [134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read [134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read [134509.284609] ldm_validate_partition_table(): Disk read failed. [134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read [134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read [134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read [134509.289553] mmcblk0: unable to read partition table [134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB [134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB [134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read After patch: [134551.089613] mmc0: switch to bus width 4 failed [134551.090377] mmc0: new high speed MMC card at address 0001 [134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB [134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 [134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB [134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode") Cc: stable@vger.kernel.org Signed-off-by: Ivan Semenov <ivan@semenov.dev> Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-23mmc: slot-gpio: Allow non-sleeping GPIO roAlexander Stein1-1/+5
commit cc9432c4fb159a3913e0ce3173b8218cd5bad2e0 upstream. This change uses the appropriate _cansleep or non-sleeping API for reading GPIO read-only state. This allows users with GPIOs that never sleepbeing called in atomic context. Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow non-sleeping GPIO cd"). Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240206083912.2543142-1-alexander.stein@ew.tq-group.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-02-23mmc: core: Use mrq.sbc in close-ended ffuAvri Altman1-3/+43
commit 4d0c8d0aef6355660b6775d57ccd5d4ea2e15802 upstream. Field Firmware Update (ffu) may use close-ended or open ended sequence. Each such sequence is comprised of a write commands enclosed between 2 switch commands - to and from ffu mode. So for the close-ended case, it will be: cmd6->cmd23-cmd25-cmd6. Some host controllers however, get confused when multi-block rw is sent without sbc, and may generate auto-cmd12 which breaks the ffu sequence. I encountered this issue while testing fwupd (github.com/fwupd/fwupd) on HP Chromebook x2, a qualcomm based QC-7c, code name - strongbad. Instead of a quirk, or hooking the request function of the msm ops, it would be better to fix the ioctl handling and make it use mrq.sbc instead of issuing SET_BLOCK_COUNT separately. Signed-off-by: Avri Altman <avri.altman@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231129092535.3278-1-avri.altman@wdc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-15mmc: core: Cancel delayed work before releasing hostGeert Uytterhoeven1-0/+1
commit 1036f69e251380573e256568cf814506e3fb9988 upstream. On RZ/Five SMARC EVK, where probing of SDHI is deferred due to probe deferral of the vqmmc-supply regulator: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/time/timer.c:1738 __run_timers.part.0+0x1d0/0x1e8 Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 6.7.0-rc4 #101 Hardware name: Renesas SMARC EVK based on r9a07g043f01 (DT) epc : __run_timers.part.0+0x1d0/0x1e8 ra : __run_timers.part.0+0x134/0x1e8 epc : ffffffff800771a4 ra : ffffffff80077108 sp : ffffffc800003e60 gp : ffffffff814f5028 tp : ffffffff8140c5c0 t0 : ffffffc800000000 t1 : 0000000000000001 t2 : ffffffff81201300 s0 : ffffffc800003f20 s1 : ffffffd8023bc4a0 a0 : 00000000fffee6b0 a1 : 0004010000400000 a2 : ffffffffc0000016 a3 : ffffffff81488640 a4 : ffffffc800003e60 a5 : 0000000000000000 a6 : 0000000004000000 a7 : ffffffc800003e68 s2 : 0000000000000122 s3 : 0000000000200000 s4 : 0000000000000000 s5 : ffffffffffffffff s6 : ffffffff81488678 s7 : ffffffff814886c0 s8 : ffffffff814f49c0 s9 : ffffffff81488640 s10: 0000000000000000 s11: ffffffc800003e60 t3 : 0000000000000240 t4 : 0000000000000a52 t5 : ffffffd8024ae018 t6 : ffffffd8024ae038 status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003 [<ffffffff800771a4>] __run_timers.part.0+0x1d0/0x1e8 [<ffffffff800771e0>] run_timer_softirq+0x24/0x4a [<ffffffff80809092>] __do_softirq+0xc6/0x1fa [<ffffffff80028e4c>] irq_exit_rcu+0x66/0x84 [<ffffffff80800f7a>] handle_riscv_irq+0x40/0x4e [<ffffffff80808f48>] call_on_irq_stack+0x1c/0x28 ---[ end trace 0000000000000000 ]--- What happens? renesas_sdhi_probe() { tmio_mmc_host_alloc() mmc_alloc_host() INIT_DELAYED_WORK(&host->detect, mmc_rescan); devm_request_irq(tmio_mmc_irq); /* * After this, the interrupt handler may be invoked at any time * * tmio_mmc_irq() * { * __tmio_mmc_card_detect_irq() * mmc_detect_change() * _mmc_detect_change() * mmc_schedule_delayed_work(&host->detect, delay); * } */ tmio_mmc_host_probe() tmio_mmc_init_ocr() -EPROBE_DEFER tmio_mmc_host_free() mmc_free_host() } When expire_timers() runs later, it warns because the MMC host structure containing the delayed work was freed, and now contains an invalid work function pointer. Fix this by cancelling any pending delayed work before releasing the MMC host structure. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/205dc4c91b47e31b64392fe2498c7a449e717b4b.1701689330.git.geert+renesas@glider.be Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-01-15mmc: rpmb: fixes pause retune on all RPMB partitions.Jorge Ramirez-Ortiz1-3/+4
commit e7794c14fd73e5eb4a3e0ecaa5334d5a17377c50 upstream. When RPMB was converted to a character device, it added support for multiple RPMB partitions (Commit 97548575bef3 ("mmc: block: Convert RPMB to a character device"). One of the changes in this commit was transforming the variable target_part defined in __mmc_blk_ioctl_cmd into a bitmask. This inadvertently regressed the validation check done in mmc_blk_part_switch_pre() and mmc_blk_part_switch_post(), so let's fix it. Fixes: 97548575bef3 ("mmc: block: Convert RPMB to a character device") Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20231201153143.1449753-1-jorge@foundries.io Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-13mmc: block: Be sure to wait while busy in CQE error recoveryAdrian Hunter3-1/+5
commit c616696a902987352426fdaeec1b0b3240949e6b upstream. STOP command does not guarantee to wait while busy, but subsequent command MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so be sure to wait by employing mmc_poll_for_busy(). Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Christian Loehle <christian.loehle@arm.com> Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-08mmc: core: add helpers mmc_regulator_enable/disable_vqmmcHeiner Kallweit1-0/+41
[ Upstream commit 8d91f3f8ae57e6292142ca89f322e90fa0d6ac02 ] There's a number of drivers (e.g. dw_mmc, meson-gx, mmci, sunxi) using the same mechanism and a private flag vqmmc_enabled to deal with enabling/disabling the vqmmc regulator. Move this to the core and create new helpers mmc_regulator_enable_vqmmc and mmc_regulator_disable_vqmmc. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/71586432-360f-9b92-17f6-b05a8a971bc2@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Stable-dep-of: 477865af60b2 ("mmc: sdhci-sprd: Fix vqmmc not shutting down after the card was pulled") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-12-08mmc: block: Retry commands in CQE error recoveryAdrian Hunter1-2/+5
[ Upstream commit 8155d1fa3a747baad5caff5f8303321d68ddd48c ] It is important that MMC_CMDQ_TASK_MGMT command to discard the queue is successful because otherwise a subsequent reset might fail to flush the cache first. Retry it and the previous STOP command. Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Link: https://lore.kernel.org/r/20231103084720.6886-5-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-12-08mmc: core: convert comma to semicolonZheng Yongjun1-4/+4
[ Upstream commit 6b1dc6229aecbcb45e8901576684a8c09e25ad7b ] Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Link: https://lore.kernel.org/r/20201216131737.14883-1-zhengyongjun3@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Stable-dep-of: 8155d1fa3a74 ("mmc: block: Retry commands in CQE error recovery") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-12-08mmc: block: Do not lose cache flush during CQE error recoveryAdrian Hunter1-0/+2
commit 174925d340aac55296318e43fd96c0e1d196e105 upstream. During CQE error recovery, error-free data commands get requeued if there is any data left to transfer, but non-data commands are completed even though they have not been processed. Requeue them instead. Note the only non-data command is cache flush, which would have resulted in a cache flush being lost if it was queued at the time of CQE recovery. Fixes: 1e8e55b67030 ("mmc: block: Add CQE support") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Link: https://lore.kernel.org/r/20231103084720.6886-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-11-20Revert "mmc: core: Capture correct oemid-bits for eMMC cards"Dominique Martinet1-1/+1
commit 421b605edb1ce611dee06cf6fd9a1c1f2fd85ad0 upstream. This reverts commit 84ee19bffc9306128cd0f1c650e89767079efeff. The commit above made quirks with an OEMID fail to be applied, as they were checking card->cid.oemid for the full 16 bits defined in MMC_FIXUP macros but the field would only contain the bottom 8 bits. eMMC v5.1A might have bogus values in OEMID's higher bits so another fix will be made, but it has been decided to revert this until that is ready. Fixes: 84ee19bffc93 ("mmc: core: Capture correct oemid-bits for eMMC cards") Link: https://lkml.kernel.org/r/ZToJsSLHr8RnuTHz@codewreck.org Link: https://lkml.kernel.org/r/CAPDyKFqkKibcXnwjnhc3+W1iJBHLeqQ9BpcZrSwhW2u9K2oUtg@mail.gmail.com Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com> Cc: stable@vger.kernel.org Cc: Alex Fetters <Alex.Fetters@garmin.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Link: https://lore.kernel.org/r/20231103004220.1666641-1-asmadeus@codewreck.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-25mmc: core: Capture correct oemid-bits for eMMC cardsAvri Altman1-1/+1
commit 84ee19bffc9306128cd0f1c650e89767079efeff upstream. The OEMID is an 8-bit binary number rather than 16-bit as the current code parses for. The OEMID occupies bits [111:104] in the CID register, see the eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from the legacy MMC specs (v3.31 and before). Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This means we ignore the impact on some of those old MMC cards that may be out there, but on the other hand this shouldn't be a problem as the OEMID seems not be an important feature for these cards. Signed-off-by: Avri Altman <avri.altman@wdc.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230927071500.1791882-1-avri.altman@wdc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-25mmc: core: sdio: hold retuning if sdio in 1-bit modeHaibo Chen1-1/+7
commit 32a9cdb8869dc111a0c96cf8e1762be9684af15b upstream. tuning only support in 4-bit mode or 8 bit mode, so in 1-bit mode, need to hold retuning. Find this issue when use manual tuning method on imx93. When system resume back, SDIO WIFI try to switch back to 4 bit mode, first will trigger retuning, and all tuning command failed. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: dfa13ebbe334 ("mmc: host: Add facility to support re-tuning") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230830093922.3095850-1-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-26mmc: block: Fix in_flight[issue_type] value errorYibin Ding1-3/+4
commit 4b430d4ac99750ee2ae2f893f1055c7af1ec3dc5 upstream. For a completed request, after the mmc_blk_mq_complete_rq(mq, req) function is executed, the bitmap_tags corresponding to the request will be cleared, that is, the request will be regarded as idle. If the request is acquired by a different type of process at this time, the issue_type of the request may change. It further caused the value of mq->in_flight[issue_type] to be abnormal, and a large number of requests could not be sent. p1: p2: mmc_blk_mq_complete_rq blk_mq_free_request blk_mq_get_request blk_mq_rq_ctx_init mmc_blk_mq_dec_in_flight mmc_issue_type(mq, req) This strategy can ensure the consistency of issue_type before and after executing mmc_blk_mq_complete_rq. Fixes: 81196976ed94 ("mmc: block: Add blk-mq support") Cc: stable@vger.kernel.org Signed-off-by: Yibin Ding <yibin.ding@unisoc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230802023023.1318134-1-yunlong.xing@unisoc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-26mmc: core: add devm_mmc_alloc_hostHeiner Kallweit1-0/+26
[ Upstream commit 80df83c2c57e75cb482ccf0c639ce84703ab41a2 ] Add a device-managed version of mmc_alloc_host(). The argument order is reversed compared to mmc_alloc_host() because device-managed functions typically have the device argument first. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/6d8f9fdc-7c9e-8e4f-e6ef-5470b971c74e@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Stable-dep-of: b8ada54fa1b8 ("mmc: meson-gx: fix deferred probing") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-07-27mmc: core: disable TRIM on Micron MTFC4GACAJCN-1MRobert Marko1-0/+7
commit dbfbddcddcebc9ce8a08757708d4e4a99d238e44 upstream. It seems that Micron MTFC4GACAJCN-1M despite advertising TRIM support does not work when the core is trying to use REQ_OP_WRITE_ZEROES. We are seeing the following errors in OpenWrt under 6.1 on Qnap Qhora 301W that we did not previously have and tracked it down to REQ_OP_WRITE_ZEROES: [ 18.085950] I/O error, dev loop0, sector 596 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 2 Disabling TRIM makes the error go away, so lets add a quirk for this eMMC to disable TRIM. Signed-off-by: Robert Marko <robimarko@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230530213259.1776512-1-robimarko@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-27mmc: core: disable TRIM on Kingston EMMC04G-M627Robert Marko1-0/+7
commit f1738a1f816233e6dfc2407f24a31d596643fd90 upstream. It seems that Kingston EMMC04G-M627 despite advertising TRIM support does not work when the core is trying to use REQ_OP_WRITE_ZEROES. We are seeing I/O errors in OpenWrt under 6.1 on Zyxel NBG7815 that we did not previously have and tracked it down to REQ_OP_WRITE_ZEROES. Trying to use fstrim seems to also throw errors like: [93010.835112] I/O error, dev loop0, sector 16902 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 2 Disabling TRIM makes the error go away, so lets add a quirk for this eMMC to disable TRIM. Signed-off-by: Robert Marko <robimarko@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230619193621.437358-1-robimarko@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-06-21mmc: block: ensure error propagation for non-blkChristian Loehle1-0/+5
commit 003fb0a51162d940f25fc35e70b0996a12c9e08a upstream. Requests to the mmc layer usually come through a block device IO. The exceptions are the ioctl interface, RPMB chardev ioctl and debugfs, which issue their own blk_mq requests through blk_execute_rq and do not query the BLK_STS error but the mmcblk-internal drv_op_result. This patch ensures that drv_op_result defaults to an error and has to be overwritten by the operation to be considered successful. The behavior leads to a bug where the request never propagates the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged) and thus may assume that their call executed successfully when it did not. While always checking the blk_execute_rq return value would be advised, let's eliminate the error by always setting drv_op_result as -EIO to be overwritten on success (or other error) Fixes: 614f0388f580 ("mmc: block: move single ioctl() commands to block requests") Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-02-22mmc: sdio: fix possible resource leaks in some error pathsYang Yingliang2-15/+14
commit 605d9fb9556f8f5fb4566f4df1480f280f308ded upstream. If sdio_add_func() or sdio_init_func() fails, sdio_remove_func() can not release the resources, because the sdio function is not presented in these two cases, it won't call of_node_put() or put_device(). To fix these leaks, make sdio_func_present() only control whether device_del() needs to be called or not, then always call of_node_put() and put_device(). In error case in sdio_init_func(), the reference of 'card->dev' is not get, to avoid redundant put in sdio_free_func_cis(), move the get_device() to sdio_alloc_func() and put_device() to sdio_release_func(), it can keep the get/put function be balanced. Without this patch, while doing fault inject test, it can get the following leak reports, after this fix, the leak is gone. unreferenced object 0xffff888112514000 (size 2048): comm "kworker/3:2", pid 65, jiffies 4294741614 (age 124.774s) hex dump (first 32 bytes): 00 e0 6f 12 81 88 ff ff 60 58 8d 06 81 88 ff ff ..o.....`X...... 10 40 51 12 81 88 ff ff 10 40 51 12 81 88 ff ff .@Q......@Q..... backtrace: [<000000009e5931da>] kmalloc_trace+0x21/0x110 [<000000002f839ccb>] mmc_alloc_card+0x38/0xb0 [mmc_core] [<0000000004adcbf6>] mmc_sdio_init_card+0xde/0x170 [mmc_core] [<000000007538fea0>] mmc_attach_sdio+0xcb/0x1b0 [mmc_core] [<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core] unreferenced object 0xffff888112511000 (size 2048): comm "kworker/3:2", pid 65, jiffies 4294741623 (age 124.766s) hex dump (first 32 bytes): 00 40 51 12 81 88 ff ff e0 58 8d 06 81 88 ff ff .@Q......X...... 10 10 51 12 81 88 ff ff 10 10 51 12 81 88 ff ff ..Q.......Q..... backtrace: [<000000009e5931da>] kmalloc_trace+0x21/0x110 [<00000000fcbe706c>] sdio_alloc_func+0x35/0x100 [mmc_core] [<00000000c68f4b50>] mmc_attach_sdio.cold.18+0xb1/0x395 [mmc_core] [<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core] Fixes: 3d10a1ba0d37 ("sdio: fix reference counting in sdio_remove_func()") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230130125808.3471254-1-yangyingliang@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-12-08mmc: core: Fix ambiguous TRIM and DISCARD argChristian Löhle1-2/+7
commit 489d144563f23911262a652234b80c70c89c978b upstream. Clean up the MMC_TRIM_ARGS define that became ambiguous with DISCARD introduction. While at it, let's fix one usage where MMC_TRIM_ARGS falsely included DISCARD too. Fixes: b3bf915308ca ("mmc: core: new discard feature support at eMMC v4.5") Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/11376b5714964345908f3990f17e0701@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-12-08mmc: mmc_test: Fix removal of debugfs fileYe Bin1-1/+2
commit f4307b4df1c28842bb1950ff0e1b97e17031b17f upstream. In __mmc_test_register_dbgfs_file(), we need to assign 'file', as it's being used when removing the debugfs files when the mmc_test module is removed. Fixes: a04c50aaa916 ("mmc: core: no need to check return value of debugfs_create functions") Signed-off-by: Ye Bin <yebin10@huawei.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org [Ulf: Re-wrote the commit msg] Link: https://lore.kernel.org/r/20221123095506.1965691-1-yebin@huaweicloud.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-25mmc: core: properly select voltage range without power cycleYann Gautier1-1/+7
commit 39a72dbfe188291b156dd6523511e3d5761ce775 upstream. In mmc_select_voltage(), if there is no full power cycle, the voltage range selected at the end of the function will be on a single range (e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V), the mask shift should be reduced by 1. This issue was triggered by using a specific SD-card (Verbatim Premium 16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes and there is no power cycle. And the card was failing to switch to high-speed mode. When adding the range 3.2V/3.3V for this card with the proposed shift change, the card can switch to high-speed mode. Fixes: ce69d37b7d8f ("mmc: core: Prevent violation of specs while initializing cards") Signed-off-by: Yann Gautier <yann.gautier@foss.st.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-11-03mmc: core: Fix kernel panic when remove non-standard SDIO cardMatthew Ma1-1/+2
commit 9972e6b404884adae9eec7463e30d9b3c9a70b18 upstream. SDIO tuple is only allocated for standard SDIO card, especially it causes memory corruption issues when the non-standard SDIO card has removed, which is because the card device's reference counter does not increase for it at sdio_init_func(), but all SDIO card device reference counter gets decreased at sdio_release_func(). Fixes: 6f51be3d37df ("sdio: allow non-standard SDIO cards") Signed-off-by: Matthew Ma <mahongwei@zeku.com> Reviewed-by: Weizhao Ouyang <ouyangweizhao@zeku.com> Reviewed-by: John Wang <wangdayu@zeku.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221014034951.2300386-1-ouyangweizhao@zeku.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-10-30mmc: core: Add SD card quirk for broken discardAvri Altman3-1/+18
commit 07d2872bf4c864eb83d034263c155746a2fb7a3b upstream. Some SD-cards from Sandisk that are SDA-6.0 compliant reports they supports discard, while they actually don't. This might cause mk2fs to fail while trying to format the card and revert it to a read-only mode. To fix this problem, let's add a card quirk (MMC_QUIRK_BROKEN_SD_DISCARD) to indicate that we shall fall-back to use the legacy erase command instead. Signed-off-by: Avri Altman <avri.altman@wdc.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220928095744.16455-1-avri.altman@wdc.com [Ulf: Updated the commit message] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-10-15mmc: core: Terminate infinite loop in SD-UHS voltage switchBrian Norris1-1/+2
[ Upstream commit e9233917a7e53980664efbc565888163c0a33c3f ] This loop intends to retry a max of 10 times, with some implicit termination based on the SD_{R,}OCR_S18A bit. Unfortunately, the termination condition depends on the value reported by the SD card (*rocr), which may or may not correctly reflect what we asked it to do. Needless to say, it's not wise to rely on the card doing what we expect; we should at least terminate the loop regardless. So, check both the input and output values, so we ensure we will terminate regardless of the SD card behavior. Note that SDIO learned a similar retry loop in commit 0797e5f1453b ("mmc: core: Fixup signal voltage switch"), but that used the 'ocr' result, and so the current pre-terminating condition looks like: rocr & ocr & R4_18V_PRESENT (i.e., it doesn't have the same bug.) This addresses a number of crash reports seen on ChromeOS that look like the following: ... // lots of repeated: ... <4>[13142.846061] mmc1: Skipping voltage switch <4>[13143.406087] mmc1: Skipping voltage switch <4>[13143.964724] mmc1: Skipping voltage switch <4>[13144.526089] mmc1: Skipping voltage switch <4>[13145.086088] mmc1: Skipping voltage switch <4>[13145.645941] mmc1: Skipping voltage switch <3>[13146.153969] INFO: task halt:30352 blocked for more than 122 seconds. ... Fixes: f2119df6b764 ("mmc: sd: add support for signal voltage switch procedure") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20220914014010.2076169-1-briannorris@chromium.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-10-15mmc: core: Replace with already defined values for readabilityChanWoo Lee1-1/+1
[ Upstream commit e427266460826bea21b70f9b2bb29decfb2c2620 ] SD_ROCR_S18A is already defined and is used to check the rocr value, so let's replace with already defined values for readability. Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220706004840.24812-1-cw9316.lee@samsung.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Stable-dep-of: e9233917a7e5 ("mmc: core: Terminate infinite loop in SD-UHS voltage switch") Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-28mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failureAdrian Hunter1-26/+16
[ Upstream commit 63f1560930e4e1c4f6279b8ae715c9841fe1a6d3 ] If re-initialization results is a different signal voltage, because the voltage switch failed previously, but not this time (or vice versa), then sd3_bus_mode will be inconsistent with the card because the SD_SWITCH command is done only upon first initialization. Fix by always reading SD_SWITCH information during re-initialization, which also means it does not need to be re-read later for the 1.8V fixup workaround. Note, brief testing showed SD_SWITCH took about 1.8ms to 2ms which added about 1% to 1.5% to the re-initialization time, so it's not particularly significant. Reported-by: Seunghui Lee <sh043.lee@samsung.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Seunghui Lee <sh043.lee@samsung.com> Tested-by: Seunghui Lee <sh043.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220815073321.63382-3-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-09-08mmc: core: Fix UHS-I SD 1.8V workaround branchAdrian Hunter1-3/+3
commit 15c56208c79c340686869c31595c209d1431c5e8 upstream. When introduced, upon success, the 1.8V fixup workaround in mmc_sd_init_card() would branch to practically the end of the function, to a label named "done". Unfortunately, perhaps due to the label name, over time new code has been added that really should have come after "done" not before it. Let's fix the problem by moving the label to the correct place and rename it "cont". Fixes: 045d705dc1fb ("mmc: core: Enable the MMC host software queue for the SD card") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Seunghui Lee <sh043.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220815073321.63382-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> [Backport to 5.10] Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-21mmc: block: Add single read for 4k sector cardsChristian Loehle1-14/+14
[ Upstream commit b3fa3e6dccc465969721b8bd2824213bd235efeb ] Cards with 4k native sector size may only be read 4k-aligned, accommodate for this in the single read recovery and use it. Fixes: 81196976ed946 (mmc: block: Add blk-mq support) Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Link: https://lore.kernel.org/r/cf4f316274c5474586d0d99b17db4a4c@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-14mmc: block: Fix CQE recovery reset successAdrian Hunter1-2/+1
commit a051246b786af7e4a9d9219cc7038a6e8a411531 upstream. The intention of the use of mmc_blk_reset_success() in mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and getting the same error. However, that may not be the case - any amount of time and I/O may pass before another recovery is needed, in which case there would be no reason to deny it the opportunity to recover via a reset if necessary. CQE recovery is expected seldom and failure to recover (if the clear tasks command fails), even more seldom, so it is better to allow the reset always, which can be done by calling mmc_blk_reset_success() always. Fixes: 1e8e55b67030c6 ("mmc: block: Add CQE support") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-12mmc: core: Set HS clock speed before sending HS CMD13Brian Norris1-4/+19
commit 4bc31edebde51fcf8ad0794763b8679a7ecb5ec0 upstream. Way back in commit 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that some eMMC don't respond to SEND_STATUS commands very reliably if they're still running at a low initial frequency. As mentioned in that commit, JESD84-B51 P49 suggests a sequence in which the host: 1. sets HS_TIMING 2. bumps the clock ("<= 52 MHz") 3. sends further commands It doesn't exactly require that we don't use a lower-than-52MHz frequency, but in practice, these eMMC don't like it. The aforementioned commit tried to get that right for HS400ES, although it's unclear whether this ever truly worked as committed into mainline, as other changes/refactoring adjusted the sequence in conflicting ways: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch") 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc") In any case, today we do step 3 before step 2. Let's fix that, and also apply the same logic to HS200/400, where this eMMC has problems too. Resolves errors like this seen when booting some RK3399 Gru/Scarlet systems: [ 2.058881] mmc1: CQHCI version 5.10 [ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA [ 2.209804] mmc1: mmc_select_hs400es failed, error -84 [ 2.215597] mmc1: error -84 whilst initialising MMC card [ 2.417514] mmc1: mmc_select_hs400es failed, error -110 [ 2.423373] mmc1: error -110 whilst initialising MMC card [ 2.605052] mmc1: mmc_select_hs400es failed, error -110 [ 2.617944] mmc1: error -110 whilst initialising MMC card [ 2.835884] mmc1: mmc_select_hs400es failed, error -110 [ 2.841751] mmc1: error -110 whilst initialising MMC card Ealier versions of this patch bumped to 200MHz/HS200 speeds too early, which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for the report Luca!) After a second look, it appears that aligns with JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz) rates first. Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch") Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc") Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es") Cc: Shawn Lin <shawn.lin@rock-chips.com> Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/ Reported-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Brian Norris <briannorris@chromium.org> Tested-by: Luca Weiss <luca@z3ntu.xyz> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-08mmc: host: Return an error when ->enable_sdio_irq() ops is missingUlf Hansson1-2/+13
[ Upstream commit d6c9219ca1139b74541b2a98cee47a3426d754a9 ] Even if the current WARN() notifies the user that something is severely wrong, we can still end up in a PANIC() when trying to invoke the missing ->enable_sdio_irq() ops. Therefore, let's also return an error code and prevent the host from being added. While at it, move the code into a separate function to prepare for subsequent changes and for further host caps validations. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-23mmc: block: fix read single on recovery logicChristian Löhle1-14/+14
commit 54309fde1a352ad2674ebba004a79f7d20b9f037 upstream. On reads with MMC_READ_MULTIPLE_BLOCK that fail, the recovery handler will use MMC_READ_SINGLE_BLOCK for each of the blocks, up to MMC_READ_SINGLE_RETRIES times each. The logic for this is fixed to never report unsuccessful reads as success to the block layer. On command error with retries remaining, blk_update_request was called with whatever value error was set last to. In case it was last set to BLK_STS_OK (default), the read will be reported as success, even though there was no data read from the device. This could happen on a CRC mismatch for the response, a card rejecting the command (e.g. again due to a CRC mismatch). In case it was last set to BLK_STS_IOERR, the error is reported correctly, but no retries will be attempted. Fixes: 81196976ed946c ("mmc: block: Add blk-mq support") Cc: stable@vger.kernel.org Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-27mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIOUlf Hansson1-1/+3
[ Upstream commit 8c3e5b74b9e2146f564905e50ca716591c76d4f1 ] The mmc core takes a specific path to support initializing of a non-standard SDIO card. This is triggered by looking for the card-quirk, MMC_QUIRK_NONSTD_SDIO. In mmc_sdio_init_card() this gets rather messy, as it causes the code to bail out earlier, compared to the usual path. This leads to that the OCR doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops. To make the behaviour consistent, let's instead rely on the core to save the OCR in card->ocr during initialization. Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-12-29mmc: core: Disable card detect during shutdownUlf Hansson3-1/+16
commit 66c915d09b942fb3b2b0cb2f56562180901fba17 upstream. It's seems prone to problems by allowing card detect and its corresponding mmc_rescan() work to run, during platform shutdown. For example, we may end up turning off the power while initializing a card, which potentially could damage it. To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host class device and then turn of the card detect from there. Reported-by: Al Cooper <alcooperx@gmail.com> Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211203141555.105351-1-ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-18mmc: core: Return correct emmc response in case of ioctl errorNishad Kamdar1-2/+1
[ Upstream commit e72a55f2e5ddcfb3dce0701caf925ce435b87682 ] When a read/write command is sent via ioctl to the kernel, and the command fails, the actual error response of the emmc is not sent to the user. IOCTL read/write tests are carried out using commands 17 (Single BLock Read), 24 (Single Block Write), 18 (Multi Block Read), 25 (Multi Block Write) The tests are carried out on a 64Gb emmc device. All of these tests try to access an "out of range" sector address (0x09B2FFFF). It is seen that without the patch the response received by the user is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per JEDEC specification. After applying the patch proper response is seen. This is because the function returns without copying the response to the user in case of failure. This patch fixes the issue. Hence, this memcpy is required whether we get an error response or not. Therefor it is moved up from the current position up to immediately after we have called mmc_wait_for_req(). The test code and the output of only the CMD17 is included in the commit to limit the message length. CMD17 (Test Code Snippet): ========================== printf("Forming CMD%d\n", opt_idx); /* single block read */ cmd.blksz = 512; cmd.blocks = 1; cmd.write_flag = 0; cmd.opcode = 17; //cmd.arg = atoi(argv[3]); cmd.arg = 0x09B2FFFF; /* Expecting response R1B */ cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC; memset(data, 0, sizeof(__u8) * 512); mmc_ioc_cmd_set_data(cmd, data); printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg); if(ioctl(fd, MMC_IOC_CMD, &cmd)) perror("Error"); printf("\nResponse: %08x\n", cmd.response[0]); CMD17 (Output without patch): ============================= test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17 Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4 Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF] Forming CMD17 Sending CMD17: ARG[0x09b2ffff] Error: Connection timed out Response: 00000000 (Incorrect response) CMD17 (Output with patch): ========================== test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17 [sudo] password for test: Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4 Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF] Forming CMD17 Sending CMD17: ARG[0x09b2ffff] Error: Connection timed out Response: 80000900 (Correct OUT_OF_ERROR response as per JEDEC specification) Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-07-28mmc: core: Don't allocate IDA for OF aliasesStephen Boyd1-10/+10
commit 10252bae863d09b9648bed2e035572d207200ca1 upstream. There's a chance that the IDA allocated in mmc_alloc_host() is not freed for some time because it's freed as part of a class' release function (see mmc_host_classdev_release() where the IDA is freed). If another thread is holding a reference to the class, then only once all balancing device_put() calls (in turn calling kobject_put()) have been made will the IDA be released and usable again. Normally this isn't a problem because the kobject is released before anything else that may want to use the same number tries to again, but with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty easy to try to allocate an alias from the IDA twice while the first time it was allocated is still pending a call to ida_simple_remove(). It's also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and probe defering a driver at boot that calls mmc_alloc_host() before trying to get resources that may defer likes clks or regulators. Instead of allocating from the IDA in this scenario, let's just skip it if we know this is an OF alias. The number is already "claimed" and devices that aren't using OF aliases won't try to use the claimed numbers anyway (see mmc_first_nonreserved_index()). This should avoid any issues with mmc_alloc_host() returning failures from the ida_simple_get() in the case that we're using an OF alias. Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Cc: Sujit Kautkar <sujitka@chromium.org> Reported-by: Zubin Mithra <zsm@chromium.org> Fixes: fa2d0aa96941 ("mmc: core: Allow setting slot index via device tree alias") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-19mmc: core: Allow UHS-I voltage switch for SDSC cards if supportedChristian Löhle1-4/+6
commit 09247e110b2efce3a104e57e887c373e0a57a412 upstream. While initializing an UHS-I SD card, the mmc core first tries to switch to 1.8V I/O voltage, before it continues to change the settings for the bus speed mode. However, the current behaviour in the mmc core is inconsistent and doesn't conform to the SD spec. More precisely, an SD card that supports UHS-I must set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register response. When switching to 1.8V I/O the mmc core correctly checks both of the bits, but only the SD_OCR_S18R bit when changing the settings for bus speed mode. Rather than actually fixing the code to confirm to the SD spec, let's deliberately deviate from it by requiring only the SD_OCR_S18R bit for both parts. This enables us to support UHS-I for SDSC cards (outside spec), which is actually being supported by some existing SDSC cards. Moreover, this fixes the inconsistent behaviour. Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM Cc: stable@vger.kernel.org [Ulf: Rewrote commit message and comments to clarify the changes] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-19mmc: core: clear flags before allowing to retuneWolfram Sang1-2/+5
commit 77347eda64ed5c9383961d1de9165f9d0b7d8df6 upstream. It might be that something goes wrong during tuning so the MMC core will immediately trigger a retune. In our case it was: - we sent a tuning block - there was an error so we need to send an abort cmd to the eMMC - the abort cmd had a CRC error - retune was set by the MMC core This lead to a vicious circle causing a performance regression of 75%. So, clear retuning flags before we enable retuning to start with a known cleared state. Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-14mmc: block: Disable CMDQ on the ioctl pathBean Huo1-0/+8
commit 70b52f09080565030a530a784f1c9948a7f48ca3 upstream. According to the eMMC Spec: "When command queuing is enabled (CMDQ Mode En bit in CMDQ_MODE_EN field is set to ‘1’) class 11 commands are the only method through which data transfer tasks can be issued. Existing data transfer commands, namely CMD18/CMD17 and CMD25/CMD24, are not supported when command queuing is enabled." which means if CMDQ is enabled, the FFU commands will not be supported. To fix this issue, just simply disable CMDQ on the ioctl path, and re-enable CMDQ once ioctl request is completed. Tested-by: Michael Brunner <Michael.Brunner@kontron.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 1e8e55b67030 (mmc: block: Add CQE support) Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210504203209.361597-1-huobean@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-11mmc: core: Fix hanging on I/O during system suspend for removable cardsUlf Hansson4-91/+59
commit 17a17bf50612e6048a9975450cf1bd30f93815b5 upstream. The mmc core uses a PM notifier to temporarily during system suspend, turn off the card detection mechanism for removal/insertion of (e)MMC/SD/SDIO cards. Additionally, the notifier may be used to remove an SDIO card entirely, if a corresponding SDIO functional driver don't have the system suspend/resume callbacks assigned. This behaviour has been around for a very long time. However, a recent bug report tells us there are problems with this approach. More precisely, when receiving the PM_SUSPEND_PREPARE notification, we may end up hanging on I/O to be completed, thus also preventing the system from getting suspended. In the end what happens, is that the cancel_delayed_work_sync() in mmc_pm_notify() ends up waiting for mmc_rescan() to complete - and since mmc_rescan() wants to claim the host, it needs to wait for the I/O to be completed first. Typically, this problem is triggered in Android, if there is ongoing I/O while the user decides to suspend, resume and then suspend the system again. This due to that after the resume, an mmc_rescan() work gets punted to the workqueue, which job is to verify that the card remains inserted after the system has resumed. To fix this problem, userspace needs to become frozen to suspend the I/O, prior to turning off the card detection mechanism. Therefore, let's drop the PM notifiers for mmc subsystem altogether and rely on the card detection to be turned off/on as a part of the system_freezable_wq, that we are already using. Moreover, to allow and SDIO card to be removed during system suspend, let's manage this from a ->prepare() callback, assigned at the mmc_host_class level. In this way, we can use the parent device (the mmc_host_class device), to remove the card device that is the child, in the device_prepare() phase. Reported-by: Kiwoong Kim <kwmad.kim@samsung.com> Cc: stable@vger.kernel.org # v4.5+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210310152900.149380-1-ulf.hansson@linaro.org Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-11mmc: core: Set read only for SD cards with permanent write protect bitSeunghui Lee1-0/+6
commit 917a5336f2c27928be270226ab374ed0cbf3805d upstream. Some of SD cards sets permanent write protection bit in their CSD register, due to lifespan or internal problem. To avoid unnecessary I/O write operations, let's parse the bits in the CSD during initialization and mark the card as read only for this case. Signed-off-by: Seunghui Lee <sh043.lee@samsung.com> Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-11mmc: core: Do a power cycle when the CMD11 failsDooHyun Hwang1-1/+1
commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream. A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure into 1.8V I/O. According to the SD spec a power cycle is needed of the card, if it turns out that the CMD11 fails. Let's fix this, to allow a retry of the initialization without the voltage switch, to succeed. Note that, whether it makes sense to also retry with the voltage switch after the power cycle is a bit more difficult to know. At this point, we treat it like the CMD11 isn't supported and therefore we skip it when retrying. Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com> Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-11mmc: block: Issue a cache flush only when it's enabledAvri Altman4-3/+21
commit 97fce126e279690105ee15be652b465fd96f9997 upstream. In command queueing mode, the cache isn't flushed via the mmc_flush_cache() function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a FLUSH_CACHE opcode. In this path, we need to check if cache has been enabled, before deciding to flush the cache, along the lines of what's being done in mmc_flush_cache(). To fix this problem, let's add a new bus ops callback ->cache_enabled() and implement it for the mmc bus type. In this way, the mmc block device driver can call it to know whether cache flushing should be done. Fixes: 1e8e55b67030 (mmc: block: Add CQE support) Cc: stable@vger.kernel.org Reported-by: Brendan Peter <bpeter@lytx.com> Signed-off-by: Avri Altman <avri.altman@wdc.com> Tested-by: Brendan Peter <bpeter@lytx.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com [Ulf: Squashed the two patches and made some minor updates] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-11mmc: block: Update ext_csd.cache_ctrl if it was writtenAvri Altman1-0/+12
commit aea0440ad023ab0662299326f941214b0d7480bd upstream. The cache function can be turned ON and OFF by writing to the CACHE_CTRL byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only set on init if cache size > 0. Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write. Signed-off-by: Avri Altman <avri.altman@wdc.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-28 05:04:41 +0300