| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The data sheet states that the maximum value for registers
0x0340/0x0341 FRM_LENGTH_LINES is 65525(decimal), not the
0xFFFF defined in this driver. Correct this limit.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The sensor supports the clock lane either remaining in HS mode
during frame blanking, or dropping to LP11.
Add configuration of the mode via V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Libcamera requires the cropping information for each mode, so
add this information to the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
V4L2 sensor drivers are expected to clip the supported exposure
range based on the VBLANK configured.
IMX258 wasn't doing that as register 0x350 (FRM_LENGTH_CTL)
switches it to a mode where frame length tracks coarse exposure time.
Disable this mode and clip the range for V4L2_CID_EXPOSURE appropriately
based on V4L2_CID_VBLANK.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Extends the driver to also support 2 data lanes.
Frame rates are obviously more restricted on 2 lanes, but some
hardware simply hasn't wired more up.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
There's no reason why only a clock of 19.2MHz is supported.
Indeed this isn't even a frequency listed in the datasheet.
Add support for 24MHz as well.
The PLL settings result in slightly different link frequencies,
so parameterise those.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Out of all the registers that are defined for each mode, only around
10 differ between the modes.
Split the table into common and mode specific ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The values and ranges of V4L2_CID_VBLANK are all computed,
so there is no reason for it to be a read only control.
Remove the register values from the mode lists, add the
handler, and remove the read only flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The device tree bindings define the relevant regulators for the
sensor, so update the driver to request the regulators and control
them at the appropriate times.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Registers 0x0202 and 0x0203 are written via the control handler
for V4L2_CID_EXPOSURE, so are not needed from the mode lists.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The binned modes set DIG_CROP_X_OFFSET and DIG_CROP_IMAGE_WIDTH
to less than the full image, even though the image being captured
is meant to be a scaled version of the full array size.
Reduce X_OFFSET to 0, and increase IMAGE_WIDTH to the full array.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The output image is defined as being 4208x3118 pixels in size.
Y_ADD_STA register was set to 0, and Y_ADD_END to 3118, giving
3119 lines total.
The datasheet lists a requirement for Y_ADD_STA to be a multiple
of a power of 2 depending on binning/scaling mode (2 for full pixel,
4 for x2-bin/scale, 8 for (x2-bin)+(x2-subsample) or x4-bin, or 16
for (x4-bin)+(x2-subsample)).
(Y_ADD_END – Y_ADD_STA + 1) also has to be a similar power of 2.
The current configuration for the full res modes breaks that second
requirement, and we can't increase Y_ADD_STA to 1 to retain exactly
the same field of view as that then breaks the first requirement.
For the binned modes, they are worse off as 3118 is not a multiple of
4.
Increase the main mode to 4208x3120 so that it is the same FOV as the
binned modes, with Y_ADD_STA at 0.
Fix Y_ADD_STA and Y_ADD_END for the binned modes so that they meet the
sensor requirements.
This does change the Bayer order as the default configuration is for
H&V flips to be enabled, so readout is from Y_STA_END to Y_ADD_STA,
and this patch has changed Y_STA_END.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The IMX258_FLL_* defines are unused. Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The current code does not return anything to the user.
Although the code looks a bit dangerous (using a pointer without
checking if it is valid), it should be fine. The core validates that
sel->pad has a valid value.
Fix the following smatch error:
drivers/media/i2c/hi846.c:1854 hi846_get_selection() warn: statement has no effect 31
Fixes: e8c0882685f9 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: code -> core.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Currently we have the following algorithm to calculate what value should be
written to the exposure control of imx412.
lpfr = imx412->vblank + imx412->cur_mode->height;
shutter = lpfr - exposure;
The 'shutter' value is given to IMX412_REG_EXPOSURE_CIT however, the above
algorithm will result in the value given to IMX412_REG_EXPOSURE_CIT
decreasing as the requested exposure value from user-space goes up.
e.g.
[ 2255.713989] imx412 20-001a: Received exp 1608, analog gain 0
[ 2255.714002] imx412 20-001a: Set exp 1608, analog gain 0, shutter 1938, lpfr 3546
[ 2256.302770] imx412 20-001a: Received exp 2586, analog gain 100
[ 2256.302800] imx412 20-001a: Set exp 2586, analog gain 100, shutter 960, lpfr 3546
[ 2256.753755] imx412 20-001a: Received exp 3524, analog gain 110
[ 2256.753772] imx412 20-001a: Set exp 3524, analog gain 110, shutter 22, lpfr 3546
This behaviour results in the image having less exposure as the requested
exposure value from user-space increases.
Other sensor drivers such as ov5675, imx218, hid556 and others take the
requested exposure value and use the value directly.
Take the example of the above cited sensor drivers and directly apply the
requested exposure value from user-space. The 'lpfr' variable still
functions as before but the 'shutter' variable can be dispensed with as a
result.
Once done a similar run of the test application requesting higher exposure
looks like this, with 'exp' written directly to the sensor.
[ 133.207884] imx412 20-001a: Received exp 1608, analog gain 0
[ 133.207899] imx412 20-001a: Set exp 1608, analog gain 0, lpfr 3546
[ 133.905309] imx412 20-001a: Received exp 2844, analog gain 100
[ 133.905344] imx412 20-001a: Set exp 2844, analog gain 100, lpfr 3546
[ 134.241705] imx412 20-001a: Received exp 3524, analog gain 110
[ 134.241775] imx412 20-001a: Set exp 3524, analog gain 110, lpfr 3546
The result is then setting the sensor exposure to lower values results in
darker, less exposure images and vice versa with higher exposure values.
Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver")
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5/imx577
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core removes an argument from the i2c_mux_add_adapter() call to
further deprecate class based I2C device instantiation. All users are
converted, too.
Other that that, Andi collected a number if I2C host driver patches.
Those merges have their own description"
* tag 'i2c-for-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (72 commits)
power: supply: sbs-manager: Remove class argument from i2c_mux_add_adapter()
i2c: mux: Remove class argument from i2c_mux_add_adapter()
i2c: synquacer: Fix an error handling path in synquacer_i2c_probe()
i2c: acpi: Unbind mux adapters before delete
i2c: designware: Replace MODULE_ALIAS() with MODULE_DEVICE_TABLE()
i2c: pxa: use 'time_left' variable with wait_event_timeout()
i2c: s3c2410: use 'time_left' variable with wait_event_timeout()
i2c: rk3x: use 'time_left' variable with wait_event_timeout()
i2c: qcom-geni: use 'time_left' variable with wait_for_completion_timeout()
i2c: jz4780: use 'time_left' variable with wait_for_completion_timeout()
i2c: synquacer: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f7: use 'time_left' variable with wait_for_completion_timeout()
i2c: stm32f4: use 'time_left' variable with wait_for_completion_timeout()
i2c: st: use 'time_left' variable with wait_for_completion_timeout()
i2c: omap: use 'time_left' variable with wait_for_completion_timeout()
i2c: imx-lpi2c: use 'time_left' variable with wait_for_completion_timeout()
i2c: hix5hd2: use 'time_left' variable with wait_for_completion_timeout()
i2c: exynos5: use 'time_left' variable with wait_for_completion_timeout()
i2c: digicolor: use 'time_left' variable with wait_for_completion_timeout()
i2c: amd-mp2-plat: use 'time_left' variable with wait_for_completion_timeout()
...
|
|
99a741aa7a2d ("i2c: mux: gpio: remove support for class-based device
instantiation") removed the last call to i2c_mux_add_adapter() with a
non-null class argument. Therefore the class argument can be removed.
Note: Class-based device instantiation is a legacy mechanism which
shouldn't be used in new code, so we can rule out that this argument
may be needed again in the future.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Before this commit on probe() the driver would do:
reset=1 // from probe() calling gpiod_get(GPIOD_OUT_HIGH)
reset=0 // from resume()
msleep(20) // from resume()
So if reset was 0 before getting the GPIO the reset line would only be
driven high for a very short time and sometimes there would be errors
reading the id register afterwards.
Add a msleep(20) after getting the reset line to ensure the sensor is
properly reset:
reset=1 // from probe() calling gpiod_get(GPIOD_OUT_HIGH)
msleep(20) // from probe()
reset=0 // from resume()
msleep(20) // from resume()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
fin does not fit in 32 bits in some arches.
Found by cocci:
drivers/media/i2c/tc358746.c:847:2-8: WARNING: do_div() does a 64-by-32 division, please consider using div64_ul instead.
Link: https://lore.kernel.org/linux-media/20240429-fix-cocci-v3-22-3c4865f5a4b0@chromium.org
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
link_freq does not fit in 32 bits.
Found by cocci:
drivers/media/i2c/st-mipid02.c:329:1-7: WARNING: do_div() does a 64-by-32 division, please consider using div64_s64 instead.
Link: https://lore.kernel.org/linux-media/20240429-fix-cocci-v3-21-3c4865f5a4b0@chromium.org
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The driver should disable regulators when fails to probe.
Link: https://lore.kernel.org/linux-media/20220510114852.1719018-1-zheyuma97@gmail.com
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Protect against multiple inclusions of the max9271.h header with include
guards.
Link: https://lore.kernel.org/linux-media/20220102224803.27463-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Fix a small indentation issue in a comment block.
Link: https://lore.kernel.org/linux-media/20220101173540.9090-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Drop dev_err() and use the dev_err_probe() helper on probe path.
No functional changes intended.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Set timing-related and BLC anchor registers via cci calls instead of
hardcoding them in the register table. This prepares the driver for
implementation of configurable analogue crop and binning. No
functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Pixel array dimensions and default crop size do not belong to the
ov4689_mode structure, since they are mode independent. Make them
defines instead.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The OV4689 sensor has separate red and blue gain settings (up to 4x).
Implement appropriate controls in the driver. Default gain values
are not modified.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The OV4689 sensor supports digital gain up to 16x. Implement
corresponding control in the driver. Default digital gain value is not
modified by this patch.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The OV4689 sensor supports horizontal and vertical flipping. Add
appropriate controls to the driver. Toggling both array flip and
digital flip bits allows to achieve flipping while maintaining output
Bayer order. Note that the default value of hflip control corresponds
to both bits set, as it was before this patch.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Make horizontal blanking configurable. To do so, set HTS register
according to the requested horizontal blanking in ov4689_set_ctrl
instead of the register table. Default HTS value is not changed by
this patch. Minimal HTS value is found experimentally and corresponds
to 90 fps framerate at minimum vertical blanking. Real HTS value is
the register value multiplied by 4.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
max_fps field of struct ov4689_mode is unused in this driver, so
remove it.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use runtime PM autosuspend to avoid powering off the sensor during
fast stop-reconfigure-restart cycles.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
As the sensor may be accessible right after its async sub-device is
registered, enable runtime PM before doing so.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Use sub-device active state. Employ control handler lock to
synchronize access to the active state and s_stream.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Introduce local variable for regmap within the ov4689_set_ctrl
function. This adjustment eliminates repetition within the function.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The 'client' field within the 'ov4689' structure is solely used to
access its 'dev' member. This commit removes the 'client' field and
directly stores a pointer to the 'struct device'.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Convert the i2c register accesses to utilize the CCI helper library
rather than relying on driver-specific functions. Also, set analogue
gain in a single 16-bit write instead of two 8-bit writes.
[Sakari Ailus: Initialise sensor_gain as 0.]
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Fix a spelling error in a comment.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Put register defininitions in the order of increasing register
address.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Many values in the register table are actually power-on
defaults. Remove those and also unused HDR exposures and gains.
Annotate the remaining values using the publicly available datasheet
to facilitate further development. No functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add description for 'struct regmap *cci' member of struct imx335.
This will fix the following compile-time warning:
warning: Function parameter or struct member 'cci' not described in 'imx335'
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the avdd regulator itself.
Add support for having the driver control the sensor's avdd regulator.
Note this relies on the regulator-core providing a dummy regulator
(which it does by default) on platforms where Linux is not aware of
the avdd regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the sensor's clock itself.
Add support for having the driver control an optional clock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
On some ACPI platforms, such as Chromebooks the ACPI methods to
change the power-state (_PS0 and _PS3) fully take care of powering
on/off the sensor.
On other ACPI platforms, such as e.g. various HP models with IPU6 +
hi556 sensor, the sensor driver must control the reset GPIO itself.
Add support for having the driver control an optional reset GPIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
With ipu bridge, endpoints may only be created when ipu bridge has
initialised. This may happen after the sensor driver has first probed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add camera orientation and sensor rotation controls using
the v4l2_fwnode_device_parse() and v4l2_ctrl_new_fwnode_properties()
helpers.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add hblank control so that the sensor has all the mandatory
controls for libcamera.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add vblank control to allow changing the framerate /
higher exposure values.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The hts, vts ov2680_mode struct members always contain
OV2680_PIXELS_PER_LINE resp. OV2680_LINES_PER_FRAME,
drop them and simply use these values directly.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
There is no reason to send OV2680_END_MARGIN extra columns on top of
the mode width and the same for sending extra lines over the mode height.
This sending of extra lines/columns was inherited from the atomisp
ov2680 driver, it is unclear why this was done and this complicates
adding V4L2_CID_VBLANK support, so remove it.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
