| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 3318dc299b072a0511d6dfd8367f3304fb6d9827 ]
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca28 ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d51a15af37ce8cf59e73de51dcdce3c9f4944974 ]
They are all part of the init sequence.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221121140048.534395323@linutronix.de
Stable-dep-of: 3318dc299b07 ("irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c10f2f8b5d8027c1ea77f777f2d16cb9043a6c09 ]
struct of_device_id should normally be const.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211209132453.25623-1-wangxiang@cdjrlc.com
Stable-dep-of: 3318dc299b07 ("irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3a748d483d80f066ca4b26abe45cdc0c367d13e9 ]
Some boards with Allwinner SoCs connect the PMIC's IRQ pin to the SoC's NMI
pin instead of a normal GPIO. Since the power key is connected to the PMIC,
and people expect to wake up a suspended system via this key, the NMI IRQ
controller must stay alive when the system goes into suspend.
Add the SKIP_WAKE flag to prevent the sunxi NMI controller from going to
sleep, so that the power key can wake up those systems.
[ tglx: Fixed up coding style ]
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250112123402.388520-1-simons.philippe@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0d62a49ab55c99e8deb4593b8d9f923de1ab5c18 upstream.
When a CPU attempts to enter low power mode, it disables the redistributor
and Group 1 interrupts and reinitializes the system registers upon wakeup.
If the transition into low power mode fails, then the CPU_PM framework
invokes the PM notifier callback with CPU_PM_ENTER_FAILED to allow the
drivers to undo the state changes.
The GIC V3 driver ignores CPU_PM_ENTER_FAILED, which leaves the GIC in
disabled state.
Handle CPU_PM_ENTER_FAILED in the same way as CPU_PM_EXIT to restore normal
operation.
[ tglx: Massage change log, add Fixes tag ]
Fixes: 3708d52fc6bb ("irqchip: gic-v3: Implement CPU PM notifier")
Signed-off-by: Yogesh Lal <quic_ylal@quicinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241220093907.2747601-1-quic_ylal@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a1855f1b7c33642c9f7a01991fb763342a312e9b ]
percpu_base is used in various percpu functions that expect variable in
__percpu address space. Correct the declaration of percpu_base to
void __iomem * __percpu *percpu_base;
to declare the variable as __percpu pointer.
The patch fixes several sparse warnings:
irq-gic.c:1172:44: warning: incorrect type in assignment (different address spaces)
irq-gic.c:1172:44: expected void [noderef] __percpu *[noderef] __iomem *percpu_base
irq-gic.c:1172:44: got void [noderef] __iomem *[noderef] __percpu *
...
irq-gic.c:1231:43: warning: incorrect type in argument 1 (different address spaces)
irq-gic.c:1231:43: expected void [noderef] __percpu *__pdata
irq-gic.c:1231:43: got void [noderef] __percpu *[noderef] __iomem *percpu_base
There were no changes in the resulting object files.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/all/20241213145809.2918-2-ubizjak@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e9c4666abb5bb444dac37e2d7eb5250c8d52a45 ]
Controllers, supported by this driver, have two sets of registers:
* (main) interrupt registers control peripheral interrupt sources.
* device interrupt registers configure per-device (network interface)
interrupts and act as an extra stage before the main interrupt
registers.
In the driver unmask code, device trigger registers are used in the mask
calculation of the main interrupt sticky register, mixing two kinds of
registers.
Use the main interrupt trigger register instead.
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240925184416.54204-2-matsievskiysv@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 464cb98f1c07298c4c10e714ae0c36338d18d316 upstream.
Christoffer reports that on some implementations, writing to
GICR_ISACTIVER0 (and similar GICD registers) can race badly with a guest
issuing a deactivation of that interrupt via the system register interface.
There are multiple reasons to this:
- this uses an early write-acknoledgement memory type (nGnRE), meaning
that the write may only have made it as far as some interconnect
by the time the store is considered "done"
- the GIC itself is allowed to buffer the write until it decides to
take it into account (as long as it is in finite time)
The effects are that the activation may not have taken effect by the time
the kernel enters the guest, forcing an immediate exit, or that a guest
deactivation occurs before the interrupt is active, doing nothing.
In order to guarantee that the write to the ISACTIVER register has taken
effect, read back from it, forcing the interconnect to propagate the write,
and the GIC to process the write before returning the read.
Reported-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241106084418.3794612-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1442ee0011983f0c5c4b92380e6853afb513841a upstream.
Kunkun Jiang reported that there is a small window of opportunity for
userspace to force a change of affinity for a VPE while the VPE has already
been unmapped, but the corresponding doorbell interrupt still visible in
/proc/irq/.
Plug the race by checking the value of vmapp_count, which tracks whether
the VPE is mapped ot not, and returning an error in this case.
This involves making vmapp_count common to both GICv4.1 and its v4.0
ancestor.
Fixes: 64edfaa9a234 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP")
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/c182ece6-2ba0-ce4f-3404-dba7a3ab6c52@huawei.com
Link: https://lore.kernel.org/all/20241002204959.2051709-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80e9963fb3b5509dfcabe9652d56bf4b35542055 upstream.
As per the GICv4.1 spec (Arm IHI 0069H, 5.3.19):
"A VMAPP with {V, Alloc}=={0, x} is self-synchronizing, This means the ITS
command queue does not show the command as consumed until all of its
effects are completed."
Furthermore, VSYNC is allowed to deliver an SError when referencing a
non existent VPE.
By these definitions, a VMAPP followed by a VSYNC is a bug, as the
later references a VPE that has been unmapped by the former.
Fix it by eliding the VSYNC in this scenario.
Fixes: 64edfaa9a234 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP")
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240406022737.3898763-1-tangnianyao@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3cef738208e5c3cb7084e208caf9bbf684f24feb ]
IRQs 0 (IPI) and 1 (MSI) are handled internally by this driver,
generic_handle_domain_irq() is never called for these IRQs.
Disallow mapping these IRQs.
[ Marek: changed commit message ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c5af2c90ba5629f0424a8d315f75fb8d91713c3c upstream.
gicv2m_of_init() fails to perform an of_node_put() when
of_address_to_resource() fails, leading to a refcount leak.
Address this by moving the error handling path outside of the loop and
making it common to all failure modes.
Fixes: 4266ab1a8ff5 ("irqchip/gic-v2m: Refactor to prepare for ACPI support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240820092843.1219933-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 382d2ffe86efb1e2fa803d2cf17e5bfc34e574f3 ]
This BUG_ON() is useless, because the same effect will be obtained
by letting the code run its course and vm being dereferenced,
triggering an exception.
So just remove this check.
Signed-off-by: Guanrui Huang <guanrui.huang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240418061053.96803-3-guanrui.huang@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d73f0f49daa84176c3beee1606e73c7ffb6af8b2 upstream.
The device tree property 'xlnx,kind-of-intr' is sanity checked that the
bitmask contains only set bits which are in the range of the number of
interrupts supported by the controller.
The check is done by shifting the mask right by the number of supported
interrupts and checking the result for zero.
The data type of the mask is u32 and the number of supported interrupts is
up to 32. In case of 32 interrupts the shift is out of bounds, resulting in
a mismatch warning. The out of bounds condition is also reported by UBSAN:
UBSAN: shift-out-of-bounds in irq-xilinx-intc.c:332:22
shift exponent 32 is too large for 32-bit type 'unsigned int'
Fix it by promoting the mask to u64 for the test.
Fixes: d50466c90724 ("microblaze: intc: Refactor DT sanity check")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/1723186944-3571957-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f872d4af79fe8c71ae291ce8875b477e1669a6c7 ]
This lock is acquired under irq_desc::lock with interrupts disabled.
When PREEMPT_RT is enabled, 'spinlock_t' becomes preemptible, which results
in invalid lock acquire context;
[ BUG: Invalid wait context ]
swapper/0/1 is trying to lock:
ffff0000008fed30 (&ctl->lock){....}-{3:3}, at: meson_gpio_irq_update_bits0
other info that might help us debug this:
context-{5:5}
3 locks held by swapper/0/1:
#0: ffff0000003cd0f8 (&dev->mutex){....}-{4:4}, at: __driver_attach+0x90c
#1: ffff000004714650 (&desc->request_mutex){+.+.}-{4:4}, at: __setup_irq0
#2: ffff0000047144c8 (&irq_desc_lock_class){-.-.}-{2:2}, at: __setup_irq0
stack backtrace:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.9.9-sdkernel #1
Call trace:
_raw_spin_lock_irqsave+0x60/0x88
meson_gpio_irq_update_bits+0x34/0x70
meson8_gpio_irq_set_type+0x78/0xc4
meson_gpio_irq_set_type+0x30/0x60
__irq_set_trigger+0x60/0x180
__setup_irq+0x30c/0x6e0
request_threaded_irq+0xec/0x1a4
Fixes: 215f4cc0fb20 ("irqchip/meson: Add support for gpio interrupt controller")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240729131850.3015508-1-avkrasnov@salutedevices.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc311074f681443266ed9f5969a5b5a0e833c5bc ]
Current meson gpio irqchip driver only support 8 channels for gpio irq
line, later chips may have more then 8 channels, so need to modify code
to support more.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-3-qianggui.song@amlogic.com
Stable-dep-of: f872d4af79fe ("irqchip/meson-gpio: Convert meson_gpio_irq_controller::lock to 'raw_spinlock_t'")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6be6cba9c4371d27f78d900ccfe34bb880d9ee20 ]
The mbigen interrupt chip has its per node registers located in a
contiguous region of page sized chunks. The code maps them into virtual
address space as a contiguous region and determines the address of a node
by using the node ID as index.
mbigen chip
|-----------------|------------|--------------|
mgn_node_0 mgn_node_1 ... mgn_node_i
|--------------| |--------------| |----------------------|
[0x0000, 0x0x0FFF] [0x1000, 0x1FFF] [i*0x1000, (i+1)*0x1000 - 1]
This works correctly up to 10 nodes, but then fails because the 11th's
array slot is used for the MGN_CLEAR registers.
mbigen chip
|-----------|--------|--------|---------------|--------|
mgn_node_0 mgn_node_1 ... mgn_clear_register ... mgn_node_i
|-----------------|
[0xA000, 0xAFFF]
Skip the MGN_CLEAR register space when calculating the offset for node IDs
greater than or equal to ten.
Fixes: a6c2f87b8820 ("irqchip/mbigen: Implement the mbigen irq chip operation functions")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240730014400.1751530-1-zouyipeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33b1c47d1fc0b5f06a393bb915db85baacba18ea ]
The power domain is automatically activated from clk_prepare(). However, on
certain platforms like i.MX8QM and i.MX8QXP, the power-on handling invokes
sleeping functions, which triggers the 'scheduling while atomic' bug in the
context switch path during device probing:
BUG: scheduling while atomic: kworker/u13:1/48/0x00000002
Call trace:
__schedule_bug+0x54/0x6c
__schedule+0x7f0/0xa94
schedule+0x5c/0xc4
schedule_preempt_disabled+0x24/0x40
__mutex_lock.constprop.0+0x2c0/0x540
__mutex_lock_slowpath+0x14/0x20
mutex_lock+0x48/0x54
clk_prepare_lock+0x44/0xa0
clk_prepare+0x20/0x44
imx_irqsteer_resume+0x28/0xe0
pm_generic_runtime_resume+0x2c/0x44
__genpd_runtime_resume+0x30/0x80
genpd_runtime_resume+0xc8/0x2c0
__rpm_callback+0x48/0x1d8
rpm_callback+0x6c/0x78
rpm_resume+0x490/0x6b4
__pm_runtime_resume+0x50/0x94
irq_chip_pm_get+0x2c/0xa0
__irq_do_set_handler+0x178/0x24c
irq_set_chained_handler_and_data+0x60/0xa4
mxc_gpio_probe+0x160/0x4b0
Cure this by implementing the irq_bus_lock/sync_unlock() interrupt chip
callbacks and handle power management in them as they are invoked from
non-atomic context.
[ tglx: Rewrote change log, added Fixes tag ]
Fixes: 0136afa08967 ("irqchip: Add driver for imx-irqsteer controller")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240703163250.47887-1-shenwei.wang@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4730d2233311d86cad9dc510318d1b40e4b53cf2 ]
There are now SoCs that integrate the irqsteer controller within
a separate power domain. In order to allow this domain to be
powered down when not needed, add runtime PM support to the driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220406163701.1277930-2-l.stach@pengutronix.de
Stable-dep-of: 33b1c47d1fc0 ("irqchip/imx-irqsteer: Handle runtime power management correctly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9a50f12e579a48e124ac5adb93dafc35f0a46b8 ]
The imx_irqsteer_irq_chip struct is constant data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220406163701.1277930-1-l.stach@pengutronix.de
Stable-dep-of: 33b1c47d1fc0 ("irqchip/imx-irqsteer: Handle runtime power management correctly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b327708798809328f21da8dc14cc8883d1e8a4b3 ]
When pch_msi_parent_domain_alloc() returns an error, there is an off-by-one
in the number of interrupts to be freed.
Fix it by passing the number of successfully allocated interrupts, instead of the
relative index of the last allocated one.
Fixes: 632dcc2c75ef ("irqchip: Add Loongson PCH MSI controller")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/20240327142334.1098-1-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff3669a71afa06208de58d6bea1cc49d5e3fcbd1 ]
When alpine_msix_gic_domain_alloc() fails, there is an off-by-one in the
number of interrupts to be freed.
Fix it by passing the number of successfully allocated interrupts, instead
of the relative index of the last allocated one.
Fixes: 3841245e8498 ("irqchip/alpine-msi: Fix freeing of interrupts on allocation error path")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240327142305.1048-1-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c26591afd33adce296c022e3480dea4282b7ef91 upstream.
The error handling path in its_vpe_irq_domain_alloc() causes a double free
when its_vpe_init() fails after successfully allocating at least one
interrupt. This happens because its_vpe_irq_domain_free() frees the
interrupts along with the area bitmap and the vprop_page and
its_vpe_irq_domain_alloc() subsequently frees the area bitmap and the
vprop_page again.
Fix this by unconditionally invoking its_vpe_irq_domain_free() which
handles all cases correctly and by removing the bitmap/vprop_page freeing
from its_vpe_irq_domain_alloc().
[ tglx: Massaged change log ]
Fixes: 7d75bbb4bc1a ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Guanrui Huang <guanrui.huang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240418061053.96803-2-guanrui.huang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af9acbfc2c4b72c378d0b9a2ee023ed01055d3e2 upstream.
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a216e (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP)
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0344d6854d25a8b3b901c778b1728885dd99007 upstream.
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e92766e ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8554cba1d6dbd3c74e0549e28ddbaccbb1d6b30a ]
The STM32F4/7 EXTI driver was missing the xlate callback, so IRQ trigger
flags specified in the device tree were being ignored. This was
preventing the RTC alarm interrupt from working, because it must be set
to trigger on the rising edge to function correctly.
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231003162003.1649967-1-ben.wolsieffer@hefring.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e13cd66bd821be417c498a34928652db4ac6b436 ]
The RISC-V INTC local interrupts are per-HART (or per-CPU) so we
create INTC IRQ domain only for the INTC node belonging to the boot
HART. This means only the boot HART INTC node will be marked as
initialized and other INTC nodes won't be marked which results
downstream interrupt controllers (such as PLIC, IMSIC and APLIC
direct-mode) not being probed due to missing device suppliers.
To address this issue, we mark all INTC node for which we don't
create IRQ domain as initialized.
Reported-by: Dmitry Dunaev <dunaev@tecon.ru>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230926102801.1591126-1-dunaev@tecon.ru
Link: https://lore.kernel.org/r/20231003044403.1974628-4-apatel@ventanamicro.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 926846a703cbf5d0635cc06e67d34b228746554b ]
We normally rely on the irq_to_cpuid_[un]lock() primitives to make
sure nothing will change col->idx while performing a LPI invalidation.
However, these primitives do not cover VPE doorbells, and we have
some open-coded locking for that. Unfortunately, this locking is
pretty bogus.
Instead, extend the above primitives to cover VPE doorbells and
convert the whole thing to it.
Fixes: f3a059219bc7 ("irqchip/gic-v4.1: Ensure mutual exclusion between vPE affinity change and RD access")
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Cc: wanghaibin.wang@huawei.com
Tested-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20230617073242.3199746-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 55ad24857341c36616ecc1d9580af5626c226cf1 ]
The irq to block mapping is fixed, and interrupts from the first block
will always be routed to the first parent IRQ. But the parent interrupts
themselves can be routed to any available CPU.
This is used by the bootloader to map the first parent interrupt to the
boot CPU, regardless wether the boot CPU is the first one or the second
one.
When booting from the second CPU, the assumption that the first block's
IRQ is mapped to the first CPU breaks, and the system hangs because
interrupts do not get routed correctly.
Fix this by passing the appropriate bcm6434_l1_cpu to the interrupt
handler instead of the chip itself, so the handler always has the right
block.
Fixes: c7c42ec2baa1 ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230629072620.62527-1-jonas.gorski@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4848229494a323eeaab62eee5574ef9f7de80374 ]
The initialization function for the J-Core AIC aic_irq_of_init() is
currently missing the call to irq_alloc_descs() which allocates and
initializes all the IRQ descriptors. Add missing function call and
return the error code from irq_alloc_descs() in case the allocation
fails.
Fixes: 981b58f66cfc ("irqchip/jcore-aic: Add J-Core AIC driver")
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Tested-by: Rob Landley <rob@landley.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230510163343.43090-1-glaubitz@physik.fu-berlin.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91539341a3b6e9c868024a4292455dae36e6f58c ]
When checking for OF quirks, make sure either 'compatible' or 'property'
is set, and give up otherwise.
This avoids non-OF quirks being randomly applied as they don't have any
of the OF data that need checking.
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 44bd78dd2b88 ("irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issues")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44bd78dd2b8897f59b7e3963f088caadb7e4f047 ]
Some Chromebooks with Mediatek SoCs have a problem where the firmware
doesn't properly save/restore certain GICR registers. Newer
Chromebooks should fix this issue and we may be able to do firmware
updates for old Chromebooks. At the moment, the only known issue with
these Chromebooks is that we can't enable "pseudo NMIs" since the
priority register can be lost. Enabling "pseudo NMIs" on Chromebooks
with the problematic firmware causes crashes and freezes.
Let's detect devices with this problem and then disable "pseudo NMIs"
on them. We'll detect the problem by looking for the presence of the
"mediatek,broken-save-restore-fw" property in the GIC device tree
node. Any devices with fixed firmware will not have this property.
Our detection plan works because we never bake a Chromebook's device
tree into firmware. Instead, device trees are always bundled with the
kernel. We'll update the device trees of all affected Chromebooks and
then we'll never enable "pseudo NMI" on a kernel that is bundled with
old device trees. When a firmware update is shipped that fixes this
issue it will know to patch the device tree to remove the property.
In order to make this work, the quick detection mechanism of the GICv3
code is extended to be able to look for properties in addition to
looking at "compatible".
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230515131353.v2.2.I88dc0a0eb1d9d537de61604cd8994ecc55c0cac1@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c6c9c049510163090b979ea5f92a68ae8d93c45 ]
When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.
Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.
Before dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.
Fixes: dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d6a0e4197c04599d75d85a608c8bb16a630a38c ]
Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.
Fixes BUG:
[ 0.426106] =============================
[ 0.426257] [ BUG: Invalid wait context ]
[ 0.426422] 6.3.0-rc7-next-20230421-dirty #54 Not tainted
[ 0.426638] -----------------------------
[ 0.426766] swapper/0/1 is trying to lock:
[ 0.426954] ffffffff8104e7b8 (gic_lock){....}-{3:3}, at: gic_set_type+0x30/08
Fixes: 95150ae8b330 ("irqchip: mips-gic: Implement irq_set_type callback")
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230424103156.66753-3-jiaxun.yang@flygoat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd098a0e031928cf88c89f7577d31821e1f0e6de ]
The MIPS GIC driver uses irq_cpu_online() to go and program the
per-CPU interrupts. However, this method iterates over all IRQs
in the system, despite only 3 per-CPU interrupts being of interest.
Let's be terribly bold and do the iteration ourselves. To ensure
mutual exclusion, hold the gic_lock spinlock that is otherwise
taken while dealing with these interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20211021170414.3341522-3-maz@kernel.org
Stable-dep-of: 3d6a0e4197c0 ("irqchip/mips-gic: Use raw spinlock for gic_lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 073352e951f60946452da358d64841066c3142ff ]
Some architectures and irqchip drivers modify the cpumask returned by
irq_data_get_affinity_mask, usually by copying in to it. This is
problematic for uniprocessor configurations, where the affinity mask
should be constant, as it is known at compile time.
Add and use a setter for the affinity mask, following the pattern of
irq_data_update_effective_affinity. This allows the getter function to
return a const cpumask pointer.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> # Xen bits
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220701200056.46555-7-samuel@sholland.org
Stable-dep-of: feabecaff590 ("genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 13a157b38ca5b4f9eed81442b8821db293755961 ]
When support for the interrupt controller was added with a5042de2688d,
we forgot to update the flags to be set to contain IRQ_LEVEL. While the
flow handler is correct, the output from /proc/interrupts does not show
such interrupts as being level triggered when they are, correct that.
Fixes: a5042de2688d ("irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221216230934.2478345-3-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 94debe03e8afa1267f95a9001786a6aa506b9ff3 ]
When support for the level triggered interrupt controller flavor was
added with c0ca7262088e, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: c0ca7262088e ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02298b7bae12936ca313975b02e7f98b06670d37 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: cd844b0715ce ("irqchip/ti-sci-intr: Add support for Interrupt Router driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102085611.3955984-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9419e700021a393f67be36abd0c4f3acc6139041 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: a68a63cb4dfc ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102084208.3951758-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 071d068b89e95d1b078aa6bbcb9d0961b77d6aa1 ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: e6b78f2c3e14 ("irqchip: Add the Alpine MSIX interrupt controller")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102082811.3947760-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6caa5a2b78f5f53c433d3a3781e53325da22f0ac ]
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: f8410e626569 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230102121318.3990586-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4208d4faf36573a507b5e5de17abe342e9276759 ]
If of_iomap() failed, 'aic' should be freed before return. Otherwise
there is a memory leak.
Fixes: fead4dd49663 ("irqchip: Add driver for WPCM450 interrupt controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221115092532.1704032-1-weiyongjun@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f9ee20c85b3a3ba0afd3672630ec4f93d339f015 ]
gic_probe() calls pm_runtime_get_sync() and added fail path as
rpm_put to put usage_counter. However, pm_runtime_get_sync()
will increment usage_counter even it failed. Fix it by replacing it with
pm_runtime_resume_and_get() to keep usage counter balanced.
Fixes: 9c8edddfc992 ("irqchip/gic: Add platform driver for non-root GICs that require RPM")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221124065150.22809-1-shangxiaojing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
From: Marc Zyngier <maz@kernel.org>
commit 3f893a5962d31c0164efdbf6174ed0784f1d7603 upstream.
Now that the core code has been fixed to always give us an affinity
that only includes online CPUs, directly use this affinity when
computing a target CPU.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220405185040.206297-4-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 443685992bda9bb4f8b17fc02c9f6c60e62b1461 ]
Fix -Woverflow warnings for tegra irqchip driver which is a result
of moving arm64 custom MMIO accessor macros to asm-generic function
implementations giving a bonus type-checking now and uncovering these
overflow warnings.
drivers/irqchip/irq-tegra.c: In function ‘tegra_ictlr_suspend’:
drivers/irqchip/irq-tegra.c:151:18: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~0ul, ictlr + ICTLR_COP_IER_CLR);
^
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71349cc85e5930dce78ed87084dee098eba24b59 ]
The function ioremap() in gic_of_init() can fail, so
its return value should be checked.
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@163.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220723100128.2964304-1-williamsukatube@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f5209fee90b4544c58b4278d944425292789967 ]
The generic IPI code depends on the IRQ affinity mask being allocated
and initialized. This will not be the case if SMP is disabled. Fix up
the remaining driver that selected GENERIC_IRQ_IPI in a non-SMP config.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220701200056.46555-3-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8190cc572981f2f13b6ffc26c7cfa7899e5d3ccc ]
The MIPS GIC irqchip driver may be selected in a uniprocessor
configuration, but it unconditionally registers an IPI domain.
Limit the part of the driver dealing with IPIs to only be compiled when
GENERIC_IRQ_IPI is enabled, which corresponds to an SMP configuration.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220701200056.46555-2-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8520501346ed8d1c4a6dfa751cb57328a9c843f1 ]
The mask_ack operation clears the interrupt by writing to the PICSR
register. This we don't want for level triggered interrupt because
it does not actually clear the interrupt on the source hardware.
This was causing issues in qemu with multi core setups where
interrupts would continue to fire even though they had been cleared in
PICSR.
Just remove the mask_ack operation.
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
