| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
|
|
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is a preparation patch for simplifying the min/max quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
https://bugzilla.redhat.com/show_bug.cgi?id=1096436
Cc: stable@vger.kernel.org
Tested-and-reported-by: ajayr@bigfoot.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Recent ARM boards have the KMI devices share one interrupt line rather
than having dedicated IRQs. Update the driver to take that into account.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The number of columns of pxa27x-keypad used by various boards is not fixed.
When building keymap with call to:
matrix_keypad_build_keymap(keymap_data, NULL,
pdata->matrix_key_rows,
pdata->matrix_key_cols,
keypad->keycodes, input_dev);
it will internally calculate needed row shift and use it to fill the
keymap. Therefore when calculating the "scancode" we should no longer use
constant row shift but also calculate it from number of columns.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Building this driver on ARM/at91 always gives us this error message:
drivers/input/touchscreen/atmel-wm97xx.c:63:2: error: #error Unknown CPU, this driver only supports AT32AP700X CPUs.
Clearly this configuration is not meant to work, so let's just prevent
it in Kconfig. If we ever want to use it on another platform, we should
also pass proper resources for GPIO, IRQ and memory, which are hardcoded
to AT32AP700X at the moment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ps2 mouse and keyboard drivers use the "serio" framework that they
correctly select in Kconfig, and that in turn depends on the i8042 driver,
which is also allowed to be disabled for architectures that don't have an
i8042.
However, Kconfig also allows i8042 to be built as a module while
the serio framework is built-in, which causes this link error:
drivers/built-in.o: In function `ps2_begin_command':
:(.text+0x26b6cc): undefined reference to `i8042_check_port_owner'
:(.text+0x26b6d4): undefined reference to `i8042_lock_chip'
drivers/built-in.o: In function `ps2_end_command':
:(.text+0x26b734): undefined reference to `i8042_check_port_owner'
:(.text+0x26b73c): undefined reference to `i8042_unlock_chip'
On x86, a specific 'select SERIO_I8042' takes care of it, but
not on the other architecture that potentially have a i8042.
This patch changes the Kconfig logic to ensure that whenever
there is an i8042, it does get used for the serio driver, avoiding
the link error above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few fixups to various drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - fix touchpad initialization on Gigabyte U2442
Input: tca8418 - fix loading this driver as a module from a device tree
Input: bma150 - extend chip detection for bma180
Input: atkbd - fix keyboard not working on some LG laptops
Input: synaptics - add min/max quirk for ThinkPad Edge E431
|
|
The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Cc: stable@vger.kernel.org
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Loading the tca8418 driver as a module on a device tree based system needs
a MODULE_ALIAS because the driver name does not match the automatic
name generation rules of a 'compatible' entry on i2c bus.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This driver has been used while on the OpenPhoenux GTA04 with a BMA180.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
After issuing ATKBD_CMD_RESET_DIS, keyboard on some LG laptops stops
working. The workaround is to stop issuing ATKBD_CMD_RESET_DIS commands.
In order to keep changes in atkbd driver to the minimum we check DMI
signature and only skip ATKBD_CMD_RESET_DIS if we are running on LG
LW25-B7HV or P1-J273B.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng-Liang Song <ssl@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"The main change is that we now publish "firmware ID" for the serio
devices to help userspace figure out the kind of touchpads it is
dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.
You will also get more quirks for Synaptics touchpads in various
Lenovo laptops, a change to elantech driver to recognize even more
models, and fixups to wacom and couple other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for newer elantech touchpads
Input: soc_button_array - fix a crash during rmmod
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
Input: Add INPUT_PROP_TOPBUTTONPAD device property
Input: i8042 - add firmware_id support
Input: serio - add firmware_id sysfs attribute
Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
Input: wacom - references to 'wacom->data' should use 'unsigned char*'
Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
Input: wacom - use full 32-bit HID Usage value in switch statement
Input: wacom - missed the last bit of expresskey for DTU-1031
Input: ads7846 - fix device usage within attribute show
Input: da9055_onkey - remove use of regmap_irq_get_virq()
|
|
Newer elantech touchpads are not recognized by the current driver, since it
fails to detect their firmware version number. This prevents more advanced
touchpad features from being usable such as two-finger scrolling. This
patch allows newer touchpads to be detected and be fully functional. Tested
on Sony Vaio SVF13N17PXB.
Signed-off-by: Jordan Rife <jrife0@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When the system has zero or one button available, trying to rmmod
soc_button_array will cause crash. Fix this by properly handling -ENODEV
in probe().
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
and X1
We expect that all the Haswell series will need such quirks, sigh.
The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.
The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.
The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.
HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.
Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Check PNP ID of the PS/2 AUX port and report INPUT_PROP_TOPBUTTONPAD
property for for touchpads with top button areas.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fill in the new serio firmware_id sysfs attribute for pnp instantiated
8042 serio ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio devices exposed via platform firmware interfaces such as ACPI may
provide additional identifying information of use to userspace.
We don't associate the serio devices with the firmware device (we don't
set it as parent), so there's no way for userspace to make use of this
information.
We cannot change the parent for serio devices instantiated though a
firmware interface as that would break suspend / resume ordering.
Therefore this patch adds a new firmware_id sysfs attribute so that
userspace can get a string from there with any additional identifying
information the firmware interface may provide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some tablet PC sensors (e.g. the 0xEC found in the Thinkpad Yoga) report
more than 256 pressure levels and will experience wraparound unless the
full range is read.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
'wacom->data' contains raw binary data and can lead to unexpected behavior
if a byte under examination happens to have its MSB set.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The 0xEC sensor is used in multiple tablet PCs and curiously has versions
that report 256 levels of pressure (Samsung Slate 7) as well as versions
that report 1024 levels (Lenovo Thinkpad Yoga). To allow both versions to
work properly, we allow the value of HID_USAGE_PRESSURE reported to
override pressure_max.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
A HID Usage is a 32-bit value: an upper 16-bit "page" and a lower 16-bit
ID. While the two halves are normally reported seperately, only the
combination uniquely idenfifes a particular HID Usage.
The existing code performs the comparison in two steps, first performing a
switch on the ID and then verifying the page within each case. While this
works fine, it is very akward to handle two Usages that share a single ID,
such as HID_USAGE_PRESSURE and HID_USAGE_X because the case statement can
only have a single identifier.
To work around this, we now check the full 32-bit HID Usage directly rather
than first checking the ID and then the page. This allows the switch
statement to have distinct cases for e.g. HID_USAGE_PRESSURE and
HID_USAGE_X.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Aaron Skomra <Aaron.Skomra@wacom.com>
Reviewed-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
With commit e585c40ba (Input: ads7846 - convert to
hwmon_device_register_with_groups()) the device passed to the attribute's
show function isn't the spi device as before.
So fixup the passed device to ads7846_read12_ser.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Using platform_get_irq_byname() to retrieve the IRQ number returns the
VIRQ number rather than the local IRQ number for the device. Passing that
value then into regmap_irq_get_virq() causes a failure because the
function is expecting the local IRQ number (e.g. 0, 1, 2, 3, etc).
This patch removes use of regmap_irq_get_virq() to prevent this failure
from happening.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle"
* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: pxa: Constify OF match table
pwm: pxa: Fix typo "pwm" -> "PWM"
Revert "pwm: pxa: Use of_match_ptr()"
pwm: add support for Intel Low Power Subsystem PWM
pwm: Add CLPS711X PWM support
pwm: atmel: correct CDTY calculation
pwm: atmel: Fix polarity handling
Documentation: Add device tree bindings for Freescale FTM PWM.
pwm: Add Freescale FTM PWM driver support
pwm: pxa: Use of_match_ptr()
pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
pwm: renesas-tpu: Add dependency on HAS_IOMEM
pwm: Remove obsolete HAVE_PWM Kconfig symbol
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
Just new drivers and existing driver fixes, no core changes except for
the new uinput IOCTL to allow userspace to fetch sysfs name of the
input device that was created"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (43 commits)
Input: edt-ft5x06 - add a missing condition
Input: appletouch - fix jumps when additional fingers are detected
Input: appletouch - implement sensor data smoothing
Input: add driver for SOC button array
Input: pm8xxx-vibrator - add DT match table
Input: pmic8xxx-pwrkey - migrate to DT
Input: pmic8xxx-keypad - migrate to DT
Input: pmic8xxx-keypad - migrate to regmap APIs
Input: pmic8xxx-keypad - migrate to devm_* APIs
Input: pmic8xxx-keypad - fix build by removing gpio configuration
Input: add new driver for ARM CLPS711X keypad
Input: edt-ft5x06 - add support for M09 firmware version
Input: edt-ft5x06 - ignore touchdown events
Input: edt-ft5x06 - adjust delays to conform datasheet
Input: edt-ft5x06 - add DT support
Input: edt-ft5x06 - several cleanups; no functional change
Input: appletouch - dial back fuzz setting
Input: remove obsolete tnetv107x drivers
Input: sirfsoc-onkey - set the capability of reporting KEY_POWER
Input: da9052_onkey - use correct register bit for key status
...
|
|
First round of input updates for 3.15.
|
|
The if condition was accidentally deleted here so we return every time
instead of returning on error.
Fixes: fd335ab04b3f ('Input: edt-ft5x06 - add support for M09 firmware version')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
|
|
Addresses issues related to when a second finger enters or leaves the
field, causing the cursor to jump or the page to scroll unexpectedly; now,
we discard any movement change that happens at the exact moment we detect a
change in the number of fingers touching the trackpad. This doesn't
completely resolve the issue but does greatly mitigate it.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use smoothed version of sensor array data to calculate movement and add
weight to prior values when calculating average. This gives more granular
and more predictable movement.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch adds support for the GPIO buttons on some Intel Bay Trail
tablets originally running Windows 8. The ACPI description of these
buttons follows "Windows ACPI Design Guide for SoC Platforms".
Signed-off-by: Lejun Zhu <lejun.zhu@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Some more updates for the input subsystem.
You will get a fix for race in mousedev that has been causing quite a
few oopses lately and a small fixup for force feedback support in
evdev"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mousedev - fix race when creating mixed device
Input: don't modify the id of ioctl-provided ff effect on upload failure
|
|
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver is only supported on DT enabled platforms. Convert the
driver to DT so that it can probe properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use the regmap APIs for this driver instead of custom pm8xxx
APIs. This breaks this driver's dependency on the pm8xxx APIs and
allows us to easily port it to other bus protocols in the future.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Simplify the error paths and reduce the lines of code in this
driver by using the devm_* APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The gpio configuration in this driver doesn't work because the
gpio.h include doesn't exist. Remove the configuration as it
isn't strictly necessary, allowing us to actually compile this
driver. If it's needed in the future, it should be done via a
pinctrl driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch adds a new driver for keypad for Cirrus Logic CLPS711X CPUs.
Target CPU contain keyboard interface which can scan 8 column lines,
so we can read row GPIOs to read status and determine asserted state.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551
Reported-by: GiulioDP <depasquale.giulio@gmail.com>
Tested-by: GiulioDP <depasquale.giulio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
