| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for adl8113 10MHz to 12GHz Low Noise Amplifier with
10MHz to 14GHz bypass switches.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add clk provider feature for the adf4377.
Even though the driver was sent as an IIO driver in most cases the
device is actually seen as a clock provider.
This patch aims to cover actual usecases requested by users in order to
completely control the output frequencies from userspace.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The NXP S32G2 and S32G3 platforms integrate a successive approximation
register (SAR) ADC. Two instances are available, each providing 8
multiplexed input channels with 12-bit resolution. The conversion rate
is up to 1 Msps depending on the configuration and sampling window.
The SAR ADC supports raw, buffer, and trigger modes. It can operate
in both single-shot and continuous conversion modes, with optional
hardware triggering through the cross-trigger unit (CTU) or external
events. An internal prescaler allows adjusting the sampling clock,
while per-channel programmable sampling times provide fine-grained
trade-offs between accuracy and latency. Automatic calibration is
performed at probe time to minimize offset and gain errors.
All modes have been validated on the S32G274-RDB2 platform using an
externally generated square wave captured by the ADC. Tests covered
buffered streaming via IIO, trigger synchronization, and accuracy
verification against a precision laboratory signal source.
One potential scenario, not detected during testing, is that in some
corner cases the DMA may already have been armed for the next
transfer, which can lead dmaengine_tx_status() to return an incorrect
residue. The callback_result() operation—intended to supply the
residue directly and eliminate the need to call
dmaengine_tx_status()—also does not work. Attempting to use
dmaengine_pause() and dmaengine_resume() to prevent the residue from
being updated does not work either.
This potential scenario should apply to any driver using cyclic DMA.
However, no current driver actually handles this case, and they all rely
on the same acquisition routine (e.g., the STM32 implementation).
The NXP SAR acquisition routine has been used in production for several
years, which is a good indication of its robustness.
As the IIO is implementing the cyclic DMA support API, it is not worth
to do more spins to the current routine as it will go away when the
new API will be available.
The driver is derived from the BSP implementation and has been partly
rewritten to comply with upstream requirements. For this reason, all
contributors to the original code are listed as co-developers.
Originally-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Co-developed-by: Alexandru-Catalin Ionita <alexandru-catalin.ionita@nxp.com>
Signed-off-by: Alexandru-Catalin Ionita <alexandru-catalin.ionita@nxp.com>
Co-developed-by: Ciprian Costea <ciprianmarian.costea@nxp.com>
Signed-off-by: Ciprian Costea <ciprianmarian.costea@nxp.com>
Co-developed-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Change 'depends on INPUT_ADXL34X=n' to '!(INPUT_ADXL34X)' to allow both
drivers to be compiled as modules. The user then can use the blacklist
to block loading one.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a new IIO ADC driver for Texas Instruments ADS131M0x devices
(ADS131M02/03/04/06/08). These are 24-bit, up to 64 kSPS, simultaneous-
sampling delta-sigma ADCs accessed via SPI.
Highlights:
- Supports 2/3/4/6/8-channel variants with per-channel RAW and SCALE.
- Implements device-required full-duplex fixed-frame transfers.
- Handles both input and output CRC
Note: Despite the almost identical name, this hardware is not
compatible with the ADS131E0x series handled by
drivers/iio/adc/ti-ads131e08.c.
Signed-off-by: David Jander <david@protonic.nl>
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In the IIO_CHAN_INFO_OVERSAMPLING_RATIO case, the type parameter
is assigned from smi330_average_attr.type and then immediately
overwritten with IIO_VAL_INT on the next line.
Since smi330_average_attr.type is already initialized to IIO_VAL_INT,
the second assignment is redundant. Remove the hardcoded assignment
to maintain consistency in the code.
Signed-off-by: Massimiliano Pellizzer <mpellizzer.dev@gmail.com>
Reviewed-by: Jianping Shen <Jianping.Shen@de.bosch.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch replaces sprintf() with sysfs_emit() and sysfs_emit_at() safer
alternative with no functional changes.
Signed-off-by: Tomas Borquez <tomasborquez13@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to allow sensors to advertise tap event capability and report tap
events, define a new struct iio_event_spec array that includes a tap event
spec, and a new struct iio_chan_spec array that references the new
iio_event_spec array; for the LSM6DSV chip family, use the new
iio_chan_spec array and define an event source for tap events.
Tested on LSMDSV16X.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In preparation for adding support for more event sources, add to the
ST_LSM6DSX_CHANNEL_ACC() iio_chan_spec initializer macro an iio_event_spec
array argument, so that this macro can be used with different arrays by
sensors that support different event sources; change the st_lsm6dsx_event
struct declaration to an array (renamed as st_lsm6dsx_ev_motion) so that it
can be passed to the macro (and opportunistically move it from the header
file where it does not belong to the C file where it is used).
In addition, remove from this macro the channel type parameter and
hard-code IIO_ACCEL in the macro definition, since all callers use
IIO_ACCEL as channel type argument.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The chip info for this variant (I2C, four channels, 14 bit, internal
reference) seems to have been left out due to oversight, so
ad5686_chip_info_tbl[ID_AD5695R] is all zeroes. Initialisation of an
AD5695R still succeeds, but the resulting IIO device has no channels and no
/dev/iio:device* node.
Add the missing chip info to the table.
Fixes: 4177381b4401 ("iio:dac:ad5686: Add AD5671R/75R/94/94R/95R/96/96R support")
Signed-off-by: Andreas Kübrich <andreas.kuebrich@spektra-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
fwnode_irq_get_byname() returns a negative value on failure; if a negative
value is returned, use it as `err` argument for dev_err_probe().
While at it, add a missing trailing newline to the dev_err_probe() error
message.
Fixes: df36de13677a ("iio: accel: add ADXL380 driver")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The st_lsm6dsx_acc_channels array of struct iio_chan_spec has a non-NULL
event_spec field, indicating support for IIO events. However, event
detection is not supported for all sensors, and if userspace tries to
configure accelerometer wakeup events on a sensor device that does not
support them (e.g. LSM6DS0), st_lsm6dsx_write_event() dereferences a NULL
pointer when trying to write to the wakeup register.
Define an additional struct iio_chan_spec array whose members have a NULL
event_spec field, and use this array instead of st_lsm6dsx_acc_channels for
sensors without event detection capability.
Fixes: b5969abfa8b8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The local variable 'curr_energy' was never clamped to
PAC_193X_MIN_POWER_ACC or PAC_193X_MAX_POWER_ACC because the return
value of clamp() was not used. Fix this by assigning the clamped value
back to 'curr_energy'.
Cc: stable@vger.kernel.org
Fixes: 0fb528c8255b ("iio: adc: adding support for PAC193x")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The mask setting is 5 bits wide for the ad9434
(ref. data sheet register 0x18 FLEX_VREF). Apparently the settings
from ad9265 were copied by mistake when support for the device was added
to the driver.
Fixes: 4606d0f4b05f ("iio: adc: ad9467: add support for AD9434 high-speed ADC")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The variable ret is declared as unsigned int but is used to store return
values from functions returning int, which may be negative error codes.
Change ret from unsigned int to int.
Fixes: 849cebf8dc67 ("iio: adc: ad7606: Add iio-backend support")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The probe() function ignored the return value of spi_setup(), leaving SPI
configuration failures undetected. If spi_setup() fails, the driver should
stop initialization and propagate the error to the caller.
Add proper error handling: check the return value of spi_setup() and return
it on failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2051f25d2a26 ("iio: adc: New driver for AD7280A Lithium Ion Battery Monitoring System")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
at91_adc_interrupt can call at91_adc_touch_data_handler function
to start the work by schedule_work(&st->touch_st.workq).
If we remove the module which will call at91_adc_remove to
make cleanup, it will free indio_dev through iio_device_unregister but
quite a bit later. While the work mentioned above will be used. The
sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| at91_adc_workq_handler
at91_adc_remove |
iio_device_unregister(indio_dev) |
//free indio_dev a bit later |
| iio_push_to_buffers(indio_dev)
| //use indio_dev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in at91_adc_remove.
Fixes: 23ec2774f1cc ("iio: adc: at91-sama5d2_adc: add support for position and pressure channels")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to be able to configure event detection on a per axis
basis (for either setting an event threshold/sensitivity value, or
enabling/disabling event detection), add new axis-specific fields
to struct st_lsm6dsx_event_src, and modify the logic that handles
event configuration to properly handle axis-specific settings when
supported by a given event source.
A future commit will add actual event sources with per-axis
configurability.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In preparation for adding support for more event types, use an array
indexed by event ID instead of a scalar value to store enabled events, and
refactor the functions to configure and report events so that their
implementation is not specific for wakeup events. Move the logic to update
the global event interrupt enable flag from st_lsm6dsx_event_setup() to its
calling function, so that it can take into account also event sources
different from the source being configured. While changing the signature of
the st_lsm6dsx_event_setup() function, opportunistically add the currently
unused `axis` parameter, which will be used when adding support for
enabling and disabling events on a per axis basis.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This field is used to store the wakeup event detection threshold value.
When adding support for more event types, some of which may have different
threshold values for different axes, storing all threshold values for all
event sources would be cumbersome. Thus, remove this field altogether, and
read the currently configured value from the sensor when requested by
userspace.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The enable_event field in struct st_lsm6dsx_hw does not lend itself well to
handling multiple event sources, so it will have to be modified to add
support for more event sources. As a preparatory step, remove references to
this field from code that does not deal with event management; rework the
st_lsm6dsx_check_events() function so that it returns whether any events
are currently enabled on a given sensor.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The mask value being assigned to the irq1_func and irq2_func fields of the
irq_config struct is specific to a single event source (i.e. the wakeup
event), and as such it should be separate from the definition of the
interrupt function registers, which cover multiple event sources.
In preparation for adding support for more event types, change the
irq1_func and irq2_func type from an {address, mask} pair to an address,
and move the mask value to a new field of struct st_lsm6dsx_event_src. No
functional changes.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The st_lsm6dsx_event_settings structure contains fields specific for one
event type (wakeup). In preparation for adding support for more event
types, introduce an event id enum and a generic event source structure, and
replace wakeup-specific data in struct st_lsm6dsx_event_settings with an
array of event source structures.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Support configuring output calibration value. Among the devices
currently supported by this driver, this setting is specific to
ad9434. The offset can be used to calibrate the output against
a known input. The register is called offset, but the procedure
is best mapped internally with calibbias operation.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc/IIO driver updates from Greg KH:
"Here is the big set of char/misc/iio driver updates for 6.19-rc1. Lots
of stuff in here including:
- lots of IIO driver updates, cleanups, and additions
- large interconnect driver changes as they get converted over to a
dynamic system of ids
- coresight driver updates
- mwave driver updates
- binder driver updates and changes
- comedi driver fixes now that the fuzzers are being set loose on
them
- nvmem driver updates
- new uio driver addition
- lots of other small char/misc driver updates, full details in the
shortlog
All of these have been in linux-next for a while now"
* tag 'char-misc-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (304 commits)
char: applicom: fix NULL pointer dereference in ac_ioctl
hangcheck-timer: fix coding style spacing
hangcheck-timer: Replace %Ld with %lld
hangcheck-timer: replace printk(KERN_CRIT) with pr_crit
uio: Add SVA support for PCI devices via uio_pci_generic_sva.c
dt-bindings: slimbus: fix warning from example
intel_th: Fix error handling in intel_th_output_open
misc: rp1: Fix an error handling path in rp1_probe()
char: xillybus: add WQ_UNBOUND to alloc_workqueue users
misc: bh1770glc: use pm_runtime_resume_and_get() in power_state_store
misc: cb710: Fix a NULL vs IS_ERR() check in probe()
mux: mmio: Add suspend and resume support
virt: acrn: split acrn_mmio_dev_res out of acrn_mmiodev
greybus: gb-beagleplay: Fix timeout handling in bootloader functions
greybus: add WQ_PERCPU to alloc_workqueue users
char/mwave: drop typedefs
char/mwave: drop printk wrapper
char/mwave: remove printk tracing
char/mwave: remove unneeded fops
char/mwave: remove MWAVE_FUTZ_WITH_OTHER_DEVICES ifdeffery
...
|
|
Pull bitmap updates from Yury Norov:
- Runtime field_{get,prep}() (Geert)
- Rust ID pool updates (Alice)
- min_t() simplification (David)
- __sw_hweightN kernel-doc fixes (Andy)
- cpumask.h headers cleanup (Andy)
* tag 'bitmap-for-6.19' of github.com:/norov/linux: (32 commits)
rust_binder: use bitmap for allocation of handles
rust: id_pool: do not immediately acquire new ids
rust: id_pool: do not supply starting capacity
rust: id_pool: rename IdPool::new() to with_capacity()
rust: bitmap: add BitmapVec::new_inline()
rust: bitmap: add MAX_LEN and MAX_INLINE_LEN constants
cpumask: Don't use "proxy" headers
soc: renesas: Use bitfield helpers
clk: renesas: Use bitfield helpers
ALSA: usb-audio: Convert to common field_{get,prep}() helpers
soc: renesas: rz-sysc: Convert to common field_get() helper
pinctrl: ma35: Convert to common field_{get,prep}() helpers
iio: mlx90614: Convert to common field_{get,prep}() helpers
iio: dac: Convert to common field_prep() helper
gpio: aspeed: Convert to common field_{get,prep}() helpers
EDAC/ie31200: Convert to common field_get() helper
crypto: qat - convert to common field_get() helper
clk: at91: Convert to common field_{get,prep}() helpers
bitfield: Add non-constant field_{prep,get}() helpers
bitfield: Add less-checking __FIELD_{GET,PREP}()
...
|
|
Drop the driver-specific field_get() and field_prep() macros, in favor
of the globally available variants from <linux/bitfield.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
Drop the driver-specific field_prep() macro, in favor of the globally
available variant from <linux/bitfield.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
Prepare for the advent of globally available common field_get() and
field_prep() macros by undefining the symbols before defining local
variants. This prevents redefinition warnings from the C preprocessor
when introducing the common macros later.
Suggested-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
Prepare for the advent of a globally available common field_prep() macro
by undefining the symbol before defining a local variant. This prevents
redefinition warnings from the C preprocessor when introducing the common
macro later.
Suggested-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
Fix hp206c and st_pressure_* entries in pressure Makefiles to follow
alphabetical order as per guideline mentioned in iio/pressure/Makefile.
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for pressure and temperature rising threshold events. For
both channels *_en and *_value (in raw units) attributes are exposed.
Since in write_event_config() the ctrl_reg1.active and ctrl_reg4
are modified, accessing the data->ctrl_reg{1,4} in set_trigger_state()
and write_event_config() needs to be now guarded by data->lock.
Otherwise, it would be possible that 2 concurrent threads executing
these functions would access the data->ctrl_reg{1,4} at the same time
and then one would overwrite the other's result.
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The pressure measurement result is arranged as 20-bit unsigned value
residing in three 8-bit registers. Hence, it can be retrieved using
get_unaligned_be24() and by applying 4-bit shift.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace open-coded dma_resv_lock()/dma_resv_unlock() around
dma_buf_unmap_attachment() in iio_buffer_dmabuf_release() with the
dma_buf_unmap_attachment_unlocked() helper.
This aligns with the standard DMA-BUF API, avoids duplicating
locking logic and eases future maintenance. No functional change.
Reviewed-by: fanggeng <fanggeng@lixiang.com>
Signed-off-by: Liang Jie <liangjie@lixiang.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace lockdep_set_class() + mutex_init() by combined call
mutex_init_with_key().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Once we called device_initialize() we have to call put_device()
on it. Refactor the code to make it in the right order.
Fixes: fe6f45f6ba22 ("iio: core: check return value when calling dev_set_name()")
Fixes: 847ec80bbaa7 ("Staging: IIO: core support for device registration and management")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add missing mutex_destroy() call in iio_dev_release() to properly
clean up the mutex initialized in iio_device_alloc(). Ensure proper
resource cleanup and follows kernel practices.
Found by code review.
While at it, create a lockdep key before mutex initialisation.
This will help with converting it to the better API in the future.
Fixes: 847ec80bbaa7 ("Staging: IIO: core support for device registration and management")
Fixes: ac917a81117c ("staging:iio:core set the iio_dev.info pointer to null on unregister under lock.")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADXL318 and ADXL319 are low noise density, low power, 3-axis
accelerometers based on ADXL380 and ADXL382, respectively. The main
difference between the new parts and the existing ones are the absence
of interrupts and events like tap detection, activity/inactivity, and
free-fall detection.
Other differences in the new parts are fewer power modes, basically
allowing only idle and measurement modes, and the removal of the 12-bit
SAR ADC path for the 3-axis signals (known as lower signal chain),
being excluisive for the temperature sensor in the ADXL318/319.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The code in bmc150-accel-core.c unconditionally calls
bmc150_accel_set_interrupt() in the iio_buffer_setup_ops,
such as on the runtime PM resume path giving a kernel
splat like this if the device has no interrupts:
Unable to handle kernel NULL pointer dereference at virtual
address 00000001 when read
PC is at bmc150_accel_set_interrupt+0x98/0x194
LR is at __pm_runtime_resume+0x5c/0x64
(...)
Call trace:
bmc150_accel_set_interrupt from bmc150_accel_buffer_postenable+0x40/0x108
bmc150_accel_buffer_postenable from __iio_update_buffers+0xbe0/0xcbc
__iio_update_buffers from enable_store+0x84/0xc8
enable_store from kernfs_fop_write_iter+0x154/0x1b4
This bug seems to have been in the driver since the beginning,
but it only manifests recently, I do not know why.
Store the IRQ number in the state struct, as this is a common
pattern in other drivers, then use this to determine if we have
IRQ support or not.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The sleep variable in inv_icm45600_buffer_postdisable() could be used without
being assigned in case of error. It must be initialized to 0 by default.
Fixes: 06674a72cf7a ("iio: imu: inv_icm45600: add buffer support in iio devices")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-iio/aPi6Xw-ZoUkW76zR@stanley.mountain/
Signed-off-by: Remi Buisson <remi.buisson@tdk.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
system_percpu_wq replaced system_wq, so change the wq in iio/adc/pac1934.
The old wq (system_wq) will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This adds support for the AD5542 single channel Current Source and
Voltage Output DACs.
It is similar to the AD5542A model so just use the same id.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Co-developed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix style issues as reported by checkpatch.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make sure include files are given in alphabetical order and that we include
the ones that were missing and remove the ones we don't really use.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use the auto unlocking helpers from cleanup.h. Allows for some code
simplification.
While at it, don't use the ternary operator in
ad5446_write_dac_powerdown() and add an helper function to write the DAC
code. The reason for the function was purely to avoid having to use
unreachable().
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_mutex_init() which is helpful with CONFIG_DEBUG_MUTEXES.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Properly separate the I2C and SPI drivers into two different drivers
living in their own source file (as usual). So that no need for the
hacky ifdefery.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add missing of_device_id compatibles for the i2c and spi drivers.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Do not use an array with an enum id kind of thing. Use the more
maintainable chip_info variable per chip.
Adapt the probe functions to use the proper helpers (for SPI and I2c).
Note that in a following patch we'll also add the chip_info variables to
the of_device_id tables. Hence already use the helpers that internally use
device_get_match_data().
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
If the chip does not have an internal reference, do not ignore a missing
regulator as we won't be able to actually provide a proper scale for the
DAC. Since it's now seen as an error, flip the if() logic so errors are
treated first (which is the typical pattern).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
