| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Introduce support for Invense ICM20608 IMU, a 6-axis motion tracking device
that combines a 3-axis gyroscope and a 3-axis accelerometer:
http://www.invensense.com/products/motion-tracking/6-axis/icm-20608-2
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
|
|
This device is a package containing a MPU6050-like sensor and an AK8975
magnetometer. The magnetometer component is supported by the existing
ak8975 driver.
This patch also rephrases the Kconfig descriptions.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Ge Gao <ggao@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Not all archs have io memory.
Instead of selecting I2C_MUX (and bypassing the HAS_IOMEM dependency)
depend directly on it.
Fixes the following kconfig warning:
warning: (MEDIA_SUBDRV_AUTOSELECT && VIDEO_CX231XX && INV_MPU6050_I2C) selects I2C_MUX which has unmet direct dependencies (I2C && HAS_IOMEM)
And this build error:
ERROR: "devm_ioremap_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The only difference between the MPU6000 and the
MPU6050 is that the first also supports SPI.
Add SPI driver for this chip.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Separate this driver into core and i2c functionality.
This is in preparation for adding spi support.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Use regmap instead of i2c specific functions.
This is in preparation of splitting this driver into core and
i2c specific functionality.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This chip allows some limited number of sensors connected to it as
slaves, which can be directly accessed by register interface of this
driver.But the current upstream driver doesn't support such mode.
To attach such slaves to main processor i2c bus, chip has to be set
up in bypass mode. This change adds i2c mux, which will enable/disable
this mode for transaction to/from such slave devices.
This was discussed for a while in mailing list, this was the outcome:
Reference:
http://www.spinics.net/lists/linux-iio/msg12126.html
http://comments.gmane.org/gmane.linux.kernel.iio/11470
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Adding MPU6500 in target list for this driver.
Description:
Source
Document: MPU-6500 Register Map and Descriptions Revision 2.1
Section 3: Register Map
This section describes difference in terms device programmability
between MPU6050 and MPU6500.
These are different registers, which differs between MPU6050 and
MPU6500.
Addr Name
---------------------
1E LP_ACCEL_ODR
6C PWR_MGMT_2
77 XA_OFFSET_H
78 XA_OFFSET_L
7A YA_OFFSET_H
7B YA_OFFSET_L
7D ZA_OFFSET_H
7E ZA_OFFSET_L
But the current MPU6050 driver doesn't use registers which are different
except PWR_MGMT_2. The difference is support of "LP_WAKE_CTRL" at bit6-7
in MPU6050 mode. In MPU6500 they are not defined.
In current mpu6050 driver, only values used for this register are for
standby mode for gyro and accelerometer.
In both case frequency of wakeups is set to default and not using
bit 6-7.
So this driver van as well support MPU6500. In addition MPU6500 can
run MPU6050 mode by changing device trim settings.
So changing config comments to allow MPU6500 to use this driver.
When the driver is enhanced to support more functions, i2c driver
data INV_MPU6500 or "WHO_AM_I" register can be used to add additional
functionality.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fix:
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c: In function ‘inv_mpu6050_read_fifo’:
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:176:3: error: implicit declaration of
function ‘iio_push_to_buffers’ [-Werror=implicit-function-declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This the basic functional Invensense MPU6050 Device driver.
Signed-off-by: Ge Gao <ggao@invensense.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
