summaryrefslogtreecommitdiff
path: root/drivers/i2c
AgeCommit message (Collapse)AuthorFilesLines
2020-08-15Merge tag 'acpi-5.9-rc1-2' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI updates from Rafael Wysocki: "Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk driver and the Designware i2c driver (changes from Akshu Agrawal and Pu Wen)" * tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: clk: x86: Support RV architecture ACPI: APD: Add a fmw property is_raven clk: x86: Change name from ST to FCH ACPI: APD: Change name from ST to FCH i2c: designware: Add device HID for Hygon I2C controller
2020-08-14Merge branch 'i2c/for-5.9' of ↵Linus Torvalds33-247/+379
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: - bus recovery can now be given a pinctrl handle and the I2C core will do all the steps to switch to/from GPIO which can save quite some boilerplate code from drivers - "fallthrough" conversion - driver updates, mostly ID additions * 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits) i2c: iproc: fix race between client unreg and isr i2c: eg20t: use generic power management i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume i2c: mediatek: Fix i2c_spec_values description i2c: mediatek: Add i2c compatible for MediaTek MT8192 dt-bindings: i2c: update bindings for MT8192 SoC i2c: mediatek: Add access to more than 8GB dram in i2c driver i2c: mediatek: Add apdma sync in i2c driver i2c: i801: Add support for Intel Tiger Lake PCH-H i2c: i801: Add support for Intel Emmitsburg PCH i2c: bcm2835: Replace HTTP links with HTTPS ones Documentation: i2c: dev: 'block process call' is supported i2c: at91: Move to generic GPIO bus recovery i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs i2c: core: add generic I2C GPIO recovery dt-bindings: i2c: add generic properties for GPIO bus recovery i2c: rcar: avoid race when unregistering slave i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c i2c: tegra: Fix runtime resume to re-init VI I2C i2c: tegra: Fix the error path in tegra_i2c_runtime_resume ...
2020-08-12i2c: iproc: fix race between client unreg and isrDhananjay Phadke1-1/+12
When i2c client unregisters, synchronize irq before setting iproc_i2c->slave to NULL. (1) disable_irq() (2) Mask event enable bits in control reg (3) Erase slave address (avoid further writes to rx fifo) (4) Flush tx and rx FIFOs (5) Clear pending event (interrupt) bits in status reg (6) enable_irq() (7) Set client pointer to NULL Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318 [ 371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.025098] lr : __handle_irq_event_percpu+0x6c/0x170 [ 371.030309] sp : ffff800010003e40 [ 371.033727] x29: ffff800010003e40 x28: 0000000000000060 [ 371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df [ 371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600 [ 371.050165] x23: 0000000000000003 x22: 0000000001600000 [ 371.055645] x21: ffff800010f18888 x20: 0000000001600000 [ 371.061124] x19: ffff0008f726f080 x18: 0000000000000000 [ 371.066603] x17: 0000000000000000 x16: 0000000000000000 [ 371.072082] x15: 0000000000000000 x14: 0000000000000000 [ 371.077561] x13: 0000000000000000 x12: 0000000000000001 [ 371.083040] x11: 0000000000000000 x10: 0000000000000040 [ 371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0 [ 371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000 [ 371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000 [ 371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0 [ 371.110436] x1 : 00000000c00000af x0 : 0000000000000000 [ 371.115916] Call trace: [ 371.118439] bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.122754] __handle_irq_event_percpu+0x6c/0x170 [ 371.127606] handle_irq_event_percpu+0x34/0x88 [ 371.132189] handle_irq_event+0x40/0x120 [ 371.136234] handle_fasteoi_irq+0xcc/0x1a0 [ 371.140459] generic_handle_irq+0x24/0x38 [ 371.144594] __handle_domain_irq+0x60/0xb8 [ 371.148820] gic_handle_irq+0xc0/0x158 [ 371.152687] el1_irq+0xb8/0x140 [ 371.155927] arch_cpu_idle+0x10/0x18 [ 371.159615] do_idle+0x204/0x290 [ 371.162943] cpu_startup_entry+0x24/0x60 [ 371.166990] rest_init+0xb0/0xbc [ 371.170322] arch_call_rest_init+0xc/0x14 [ 371.174458] start_kernel+0x404/0x430 Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode") Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: use generic power managementVaibhav Gupta1-29/+7
Drivers using legacy power management .suspen()/.resume() callbacks have to manage PCI states and device's PM states themselves. They also need to take care of standard configuration registers. Switch to generic power management framework using a single "struct dev_pm_ops" variable to take the unnecessary load from the driver. This also avoids the need for the driver to directly call most of the PCI helper functions and device power state control functions, as through the generic framework PCI Core takes care of the necessary operations, and drivers are required to do only device-specific jobs. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: Drop PCI wakeup calls from .suspend/.resumeVaibhav Gupta1-3/+0
The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well as pch_i2c_resume(). Either it should enable-wake the device in .suspend() or should not invoke pci_enable_wake() at all. Concluding that this driver doesn't support enable-wake and PCI core calls pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from .suspend() and .resume(). Reported-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: mediatek: Fix i2c_spec_values descriptionMatthias Brugger1-5/+4
The struct i2c_spec_values have it's members documented but is missing the starting '@', which leads to warings like: drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values' We also delete min_high_ns member as it is not used in the code. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-07i2c: designware: Add device HID for Hygon I2C controllerPu Wen1-0/+1
Add device HID HYGO0010 to match the Hygon ACPI Vendor ID (HYGO) that was registered in http://www.uefi.org/acpi_id_list, and the I2C controller on Hygon paltform will use the HID. Signed-off-by: Pu Wen <puwen@hygon.cn> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-08-06i2c: mediatek: Add i2c compatible for MediaTek MT8192Qii Wang1-0/+15
Add i2c compatible for MT8192. Compare to MT8183 i2c controller, MT8192 support more then 8GB DMA mode. Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-06i2c: mediatek: Add access to more than 8GB dram in i2c driverQii Wang1-22/+17
Newer MTK chip support more than 8GB of dram. Replace support_33bits with more general dma_max_support and remove mtk_i2c_set_4g_mode. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-06i2c: mediatek: Add apdma sync in i2c driverQii Wang1-3/+20
With the apdma remove hand-shake signal, it need to keep i2c and apdma in sync manually. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Tiger Lake PCH-HJarkko Nikula1-0/+4
Add SMBus PCI ID on Intel Tiger Lake PCH-H. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Emmitsburg PCHMika Westerberg2-0/+5
Add support for SMBus controller on Intel Emmitsburg PCH. This is the same IP as used in Cannon Lake and derivatives. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: bcm2835: Replace HTTP links with HTTPS onesAlexander A. Klimov1-1/+1
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> [wsa: shortened commit message] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: at91: Move to generic GPIO bus recoveryCodrin Ciubotariu2-69/+3
Make the Microchip at91 driver the first to use the generic GPIO bus recovery support from the I2C core and discard the driver implementation. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOsCodrin Ciubotariu1-12/+14
Even if I2C bus GPIO recovery is optional, devm_gpiod_get() can return -EPROBE_DEFER, so we should at least treat that. This ends up with i2c_register_adapter() to be able to return -EPROBE_DEFER. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: add generic I2C GPIO recoveryCodrin Ciubotariu1-0/+126
Multiple I2C bus drivers use similar bindings to obtain information needed for I2C recovery. For example, for platforms using device-tree, the properties look something like this: &i2c { ... pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c_default>; pinctrl-1 = <&pinctrl_i2c_gpio>; sda-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; scl-gpios = <&pio 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; ... } For this reason, we can add this common initialization in the core. This way, other I2C bus drivers will be able to support GPIO recovery just by providing a pointer to platform's pinctrl and calling i2c_recover_bus() when SDA is stuck low. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> [wsa: inverted one logic for better readability, minor update to kdoc] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-04Merge tag 'uninit-macro-v5.9-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull uninitialized_var() macro removal from Kees Cook: "This is long overdue, and has hidden too many bugs over the years. The series has several "by hand" fixes, and then a trivial treewide replacement. - Clean up non-trivial uses of uninitialized_var() - Update documentation and checkpatch for uninitialized_var() removal - Treewide removal of uninitialized_var()" * tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: compiler: Remove uninitialized_var() macro treewide: Remove uninitialized_var() usage checkpatch: Remove awareness of uninitialized_var() macro mm/debug_vm_pgtable: Remove uninitialized_var() usage f2fs: Eliminate usage of uninitialized_var() macro media: sur40: Remove uninitialized_var() usage KVM: PPC: Book3S PR: Remove uninitialized_var() usage clk: spear: Remove uninitialized_var() usage clk: st: Remove uninitialized_var() usage spi: davinci: Remove uninitialized_var() usage ide: Remove uninitialized_var() usage rtlwifi: rtl8192cu: Remove uninitialized_var() usage b43: Remove uninitialized_var() usage drbd: Remove uninitialized_var() usage x86/mm/numa: Remove uninitialized_var() usage docs: deprecated.rst: Add uninitialized_var()
2020-08-04Merge tag 'arm-drivers-5.9' of ↵Linus Torvalds1-1/+25
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "A couple of subsystems have their own subsystem maintainers but choose to have the code merged through the soc tree as upstream, as the code tends to be used across multiple SoCs or has SoC specific drivers itself: - memory controllers: Krzysztof Kozlowski takes ownership of the drivers/memory subsystem and its drivers, starting out with a set of cleanup patches. A larger driver for the Tegra memory controller that was accidentally missed for v5.8 is now added. - reset controllers: Only minor updates to drivers/reset this time - firmware: The "turris mox" firmware driver gains support for signed firmware blobs The tegra firmware driver gets extended to export some debug information Various updates to i.MX firmware drivers, mostly cosmetic - ARM SCMI/SCPI: A new mechanism for platform notifications is added, among a number of minor changes. - optee: Probing of the TEE bus is rewritten to better support detection of devices that depend on the tee-supplicant user space. A new firmware based trusted platform module (fTPM) driver is added based on OP-TEE - SoC attributes: A new driver is added to provide a generic soc_device for identifying a machine through the SMCCC ARCH_SOC_ID firmware interface rather than by probing SoC family specific registers. The series also contains some cleanups to the common soc_device code. There are also a number of updates to SoC specific drivers, the main ones are: - Mediatek cmdq driver gains a few in-kernel interfaces - Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding support for additional SoC variants - The Qualcomm GENI core code gains interconnect path voting and performance level support, and integrating this into a number of device drivers. - A new driver for Samsung Exynos5800 voltage coupler for - Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC specific device drivers - Updates to the TI K3 Ring Accelerator driver" * tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits) soc: qcom: geni: Fix unused label warning soc: qcom: smd-rpm: Fix kerneldoc memory: jz4780_nemc: Only request IO memory the driver will use soc: qcom: pdr: Reorder the PD state indication ack MAINTAINERS: Add Git repository for memory controller drivers memory: brcmstb_dpfe: Fix language typo memory: samsung: exynos5422-dmc: Correct white space issues memory: samsung: exynos-srom: Correct alignment memory: pl172: Enclose macro argument usage in parenthesis memory: of: Correct kerneldoc memory: omap-gpmc: Fix language typo memory: omap-gpmc: Correct white space issues memory: omap-gpmc: Use 'unsigned int' for consistency memory: omap-gpmc: Enclose macro argument usage in parenthesis memory: omap-gpmc: Correct kerneldoc memory: mvebu-devbus: Align with open parenthesis memory: mvebu-devbus: Add missing braces to all arms of if statement memory: bt1-l2-ctl: Add blank lines after declarations soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static firmware: ti_sci: Replace HTTP links with HTTPS ones ...
2020-08-04Merge tag 'rm-unicore32' of ↵Linus Torvalds3-287/+0
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux Pull unicore32 removal from Mike Rapoport: "Remove unicore32 support. The unicore32 port do not seem maintained for a long time now, there is no upstream toolchain that can create unicore32 binaries and all the links to prebuilt toolchains for unicore32 are dead. Even compilers that were available are not supported by the kernel anymore. Guenter Roeck says: "I have stopped building unicore32 images since v4.19 since there is no available compiler that is still supported by the kernel. I am surprised that support for it has not been removed from the kernel" However, it's worth pointing out two things: - Guan Xuetao is still listed as maintainer and asked for the port to be kept around the last time Arnd suggested removing it two years ago. He promised that there would be compiler sources (presumably llvm), but has not made those available since. - https://github.com/gxt has patches to linux-4.9 and qemu-2.7, both released in 2016, with patches dated early 2019. These patches mainly restore a syscall ABI that was never part of mainline Linux but apparently used in production. qemu-2.8 removed support for that ABI and newer kernels (4.19+) can no longer be built with the old toolchain, so apparently there will not be any future updates to that git tree" * tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux: MAINTAINERS: remove "PKUNITY SOC DRIVERS" entry rtc: remove fb-puv3 driver video: fbdev: remove fb-puv3 driver pwm: remove pwm-puv3 driver input: i8042: remove support for 8042-unicore32io i2c/buses: remove i2c-puv3 driver cpufreq: remove unicore32 driver arch: remove unicore32 port
2020-07-31i2c: rcar: avoid race when unregistering slaveWolfram Sang1-3/+5
Due to the lockless design of the driver, it is theoretically possible to access a NULL pointer, if a slave interrupt was running while we were unregistering the slave. To make this rock solid, disable the interrupt for a short time while we are clearing the interrupt_enable register. This patch is purely based on code inspection. The OOPS is super-hard to trigger because clearing SAR (the address) makes interrupts even more unlikely to happen as well. While here, reinit SCR to SDBS because this bit should always be set according to documentation. There is no effect, though, because the interface is disabled. Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-31Merge tag 'v5.8-rc7' into i2c/for-5.9Wolfram Sang8-22/+45
2020-07-28i2c: slave: add sanity check when unregisteringWolfram Sang1-0/+3
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: slave: improve sanity check when registeringWolfram Sang1-3/+1
Add check for ERR_PTR and simplify code while here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2cSowjanya Komatineni1-1/+1
VI I2C is on host1x bus so APB DMA can't be used for Tegra210 VI I2C and there are no tx and rx dma channels for VI I2C. So, avoid attempt of requesting DMA channels. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix runtime resume to re-init VI I2CSowjanya Komatineni1-0/+16
VI I2C is on host1x bus and is part of VE power domain. During suspend/resume VE power domain goes through power off/on. So, controller reset followed by i2c re-initialization is required after the domain power up. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix the error path in tegra_i2c_runtime_resumeSowjanya Komatineni1-3/+8
tegra_i2c_runtime_resume does not disable prior enabled clocks properly. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Remove NULL pointer check before ↵Sowjanya Komatineni1-41/+23
clk_enable/disable/prepare/unprepare clk_enable, clk_disable, clk_prepare, and clk_unprepare APIs have implementation for checking clk pointer not NULL and clock consumers can safely call these APIs without NULL pointer check. So, this patch cleans up Tegra i2c driver to remove explicit checks before these APIs. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Don't mark VI I2C as IRQ safe runtime PMSowjanya Komatineni1-1/+9
Tegra VI I2C is part of VE power domain and typically used for camera usecases. VE power domain is not always on and is non-IRQ safe. So, IRQ safe device cannot be attached to a non-IRQ safe domain as it prevents powering off the PM domain and generic power domain driver will warn. Current driver marks all I2C devices as IRQ safe and VI I2C device does not require IRQ safe as it will not be used for atomic transfers. This patch has fix to make VI I2C as non-IRQ safe. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-27i2c: core: do not use logical device when creating irq domainWolfram Sang1-1/+1
Let's rather use its physical parent device to give proper namings and connections in debugfs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-26i2c: rcar: slave: only send STOP event when we have been addressedWolfram Sang1-3/+4
When the SSR interrupt is activated, it will detect every STOP condition on the bus, not only the ones after we have been addressed. So, enable this interrupt only after we have been addressed, and disable it otherwise. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-24i2c: revert "i2c: core: Allow drivers to disable i2c-core irq mapping"Wolfram Sang1-3/+3
This manually reverts commit d1d84bb95364ed604015c2b788caaf3dbca0262f. The only user has gone two years ago with commit 589edb56b424 ("ACPI / scan: Create platform device for INT33FE ACPI nodes") and no new user has showed up. Remove and hope we will never need it again. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-24i2c: fsi: Prevent adding adapters for ports without dts nodesEddie James1-1/+1
Ports should be defined in the devicetree if they are to be enabled on the system. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-23i2c: i2c-qcom-geni: Fix DMA transfer raceDouglas Anderson1-2/+4
When I have KASAN enabled on my kernel and I start stressing the touchscreen my system tends to hang. The touchscreen is one of the only things that does a lot of big i2c transfers and ends up hitting the DMA paths in the geni i2c driver. It appears that KASAN adds enough delay in my system to tickle a race condition in the DMA setup code. When the system hangs, I found that it was running the geni_i2c_irq() over and over again. It had these: m_stat = 0x04000080 rx_st = 0x30000011 dm_tx_st = 0x00000000 dm_rx_st = 0x00000000 dma = 0x00000001 Notably we're in DMA mode but are getting M_RX_IRQ_EN and M_RX_FIFO_WATERMARK_EN over and over again. Putting some traces in geni_i2c_rx_one_msg() showed that when we failed we were getting to the start of geni_i2c_rx_one_msg() but were never executing geni_se_rx_dma_prep(). I believe that the problem here is that we are starting the geni command before we run geni_se_rx_dma_prep(). If a transfer makes it far enough before we do that then we get into the state I have observed. Let's change the order, which seems to work fine. Although problems were seen on the RX path, code inspection suggests that the TX should be changed too. Change it as well. Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller") Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-23i2c: rcar: always clear ICSAR to avoid side effectsWolfram Sang1-0/+3
On R-Car Gen2, we get a timeout when reading from the address set in ICSAR, even though the slave interface is disabled. Clearing it fixes this situation. Note that Gen3 is not affected. To reproduce: bind and undbind an I2C slave on some bus, run 'i2cdetect' on that bus. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-23i2c: busses: Use fallthrough pseudo-keywordGustavo A. R. Silva10-19/+17
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Acked-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-22Merge tag 'qcom-drivers-for-5.9' of ↵Arnd Bergmann1-1/+25
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers Qualcomm driver updates for v5.9 For RPMh this fixes an issue where ktime was used during suspend, allows the driver to be used on ARM targets and some minor cleanups. It adds support for the latest format version in the socinfo driver and adds identifiers for SM8250 and SDM630. SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM gains compatibles MSM8994 and IPQ8074. The GENI core code gains interconnect path voting and performance level support, with subsequent patches integrating this with the SPI, I2C, UART and QSPI drivers. Following this the KGDB support for the GENI serial driver is improved, the performance related to chip-select is improved for SPI and QSPI. * tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits) soc: qcom: geni: Fix NULL pointer dereference tty: serial: qcom-geni-serial: Drop the icc bw votes in suspend for console serial: qcom_geni_serial: Always use 4 bytes per TX FIFO word serial: qcom_geni_serial: Make kgdb work even if UART isn't console spi: spi-geni-qcom: Get rid of most overhead in prepare_message() spi: spi-geni-qcom: Set the clock properly at runtime resume spi: spi-geni-qcom: Avoid clock setting if not needed spi: spi-qcom-qspi: Set an autosuspend delay of 250 ms spi: spi-qcom-qspi: Avoid clock setting if not needed spi: spi-qcom-qspi: Use OPP API to set clk/perf state firmware: qcom_scm: Add msm8994 compatible firmware: qcom_scm: Fix legacy convention SCM accessors <linux/of.h>: add stub for of_get_next_parent() to fix qcom build error dt-bindings: firmware: qcom: Add compatible for IPQ8074 SoC spi: spi-geni-qcom: Use OPP API to set clk/perf state tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state spi: spi-qcom-qspi: Add interconnect support spi: spi-geni-qcom: Add interconnect support spi: spi-geni-qcom: Combine the clock setting code tty: serial: qcom_geni_serial: Add interconnect support ... Link: https://lore.kernel.org/r/20200721044812.3429652-1-bjorn.andersson@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-22i2c: cadence: Clear HOLD bit at correct time in Rx pathRaviteja Narayanam1-9/+10
There are few issues on Zynq SOC observed in the stress tests causing timeout errors. Even though all the data is received, timeout error is thrown. This is due to an IP bug in which the COMP bit in ISR is not set at end of transfer and completion interrupt is not generated. This bug is seen on Zynq platforms when the following condition occurs: Master read & HOLD bit set & Transfer size register reaches '0'. One workaround is to clear the HOLD bit before the transfer size register reaches '0'. The current implementation checks for this at the start of the loop and also only for less than FIFO DEPTH case (ignoring the equal to case). So clear the HOLD bit when the data yet to receive is less than or equal to the FIFO DEPTH. This avoids the IP bug condition. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-22Revert "i2c: cadence: Fix the hold bit setting"Raviteja Narayanam1-7/+2
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9. There are two issues with "i2c: cadence: Fix the hold bit setting" commit. 1. In case of combined message request from user space, when the HOLD bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent on the bus even before the last message is started. This is because when the HOLD bit is cleared, the FIFOS are empty and there is no pending transfer. The STOP condition should occur only after the last message is completed. 2. The code added by the commit is redundant. Driver is handling the setting/clearing of HOLD bit in right way before the commit. The setting of HOLD bit based on 'bus_hold_flag' is taken care in cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv functions. The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and cdns_i2c_recv functions based on bus_hold_flag and byte count. Since clearing of HOLD bit is done after the slave address is written to the register (writing to address register triggers the message transfer), it is ensured that STOP condition occurs at the right time after completion of the pending transfer (last message). Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-16treewide: Remove uninitialized_var() usageKees Cook1-1/+1
Using uninitialized_var() is dangerous as it papers over real bugs[1] (or can in the future), and suppresses unrelated compiler warnings (e.g. "unused variable"). If the compiler thinks it is uninitialized, either simply initialize the variable or make compiler changes. In preparation for removing[2] the[3] macro[4], remove all remaining needless uses with the following script: git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \ xargs perl -pi -e \ 's/\buninitialized_var\(([^\)]+)\)/\1/g; s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;' drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid pathological white-space. No outstanding warnings were found building allmodconfig with GCC 9.3.0 for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64, alpha, and m68k. [1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/ [2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/ [3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/ [4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/ Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5 Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs Signed-off-by: Kees Cook <keescook@chromium.org>
2020-07-04i2c: rk3x: support master_xfer_atomicJohn Keeping1-4/+35
Enable i2c transactions in irq disabled contexts like poweroff where the PMIC is connected via i2c. Signed-off-by: John Keeping <john@metanate.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: Use separate MODULE_AUTHOR() statements for multiple authorsJarkko Nikula13-24/+30
Modules with multiple authors should use multiple MODULE_AUTHOR() statements according to comment in include/linux/module.h. Split the i2c modules with multiple authors to use multiple MODULE_AUTHOR() statements. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: mlxcpld: check correct size of maximum RECV_LEN packetWolfram Sang1-2/+2
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno to what is suggested for this error. Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michael Shych <michaelsh@mellanox.com> Tested-by: Michael Shych <michaelsh@mellanox.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: add Kconfig help text for slave modeWolfram Sang1-0/+4
I can't recall why there was none, but we surely want to have it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: slave-eeprom: update documentationWolfram Sang1-0/+3
Add more details which have either been missing ever since or describe recent additions. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: eg20t: Load module automatically if ID matchesAndy Shevchenko1-0/+1
The driver can't be loaded automatically because it misses module alias to be provided. Add corresponding MODULE_DEVICE_TABLE() call to the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: designware: platdrv: Set class based on DMIRicardo Ribalda1-1/+14
Current AMD's zen-based APUs use this core for some of its i2c-buses. With this patch we re-enable autodetection of hwmon-alike devices, so lm-sensors will be able to work automatically. It does not affect the boot-time of embedded devices, as the class is set based on the DMI information. DMI is probed only on Qtechnology QT5222 Industrial Camera Platform. DocLink: https://qtec.com/camera-technology-camera-platforms/ Fixes: 3eddad96c439 ("i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"") Signed-off-by: Ricardo Ribalda <ribalda@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-04i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665Chris Packham1-1/+2
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck low, this differs to the PCA9564 which uses 90h for this indication. Treat either 0x78 or 0x90 as an indication that the SCL line is stuck. Based on looking through the PCA9564 and PCA9665 datasheets this should be safe for both chips. The PCA9564 should not return 0x78 for any valid state and the PCA9665 should not return 0x90. Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support") Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-01i2c/buses: remove i2c-puv3 driverMike Rapoport3-287/+0
The unicore32 port is removed from the kernel. There is no point to keep stale i2c bus driver for this architecture. Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Guenter Roeck <linux@roeck-us.net>
2020-06-26i2c: core: check returned size of emulated smbus block readMans Rullgard1-0/+7
If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued on some random device to return an arbitrary value in the first byte (and nothing else). When this happens, i2c_smbus_xfer_emulated() will happily write past the end of the supplied data buffer, thus causing Bad Things to happen. To prevent this, check the size before copying the data block and return an error if it is too large. Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C") Signed-off-by: Mans Rullgard <mans@mansr.com> [wsa: use better errno] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-06-26i2c: fsi: Fix the port number field in status registerEddie James1-1/+1
The port number field in the status register was not correct, so fix it. Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm") Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-13 13:11:45 +0300