| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 7890fce6201aed46d3576e3d641f9ee5c1f0e16f ]
Value comes from DT, so it could be 0. Unlikely, but could be.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6c29f710c1ff2590109f83be3e212b86c01e0f3 ]
If a SMBus alert is received and the originating device is not found,
the reason may be that the address reported on the SMBus alert address
is corrupted, for example because multiple devices asserted alert and
do not correctly implement SMBus arbitration.
If this happens, call alert handlers on all devices connected to the
given I2C bus, in the hope that this cleans up the situation.
This change reliably fixed the problem on a system with multiple devices
on a single bus. Example log where the device on address 0x18 (ADM1021)
and on address 0x4c (ADT7461A) both had the alert line asserted:
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
lm90 3-0018: temp1 out of range, please check!
lm90 3-0018: Disabling ALERT#
lm90 3-0029: Everything OK
lm90 3-002a: Everything OK
lm90 3-004c: temp1 out of range, please check!
lm90 3-004c: temp2 out of range, please check!
lm90 3-004c: Disabling ALERT#
Fixes: b5527a7766f0 ("i2c: Add SMBus alert support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[wsa: fixed a typo in the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37c526f00bc1c4f847fc800085f8f009d2e11be6 ]
The following messages were observed while testing alert functionality
on systems with multiple I2C devices on a single bus if alert was active
on more than one chip.
smbus_alert 3-000c: SMBALERT# from dev 0x0c, flag 0
smbus_alert 3-000c: no driver alert()!
and:
smbus_alert 3-000c: SMBALERT# from dev 0x28, flag 0
Once it starts, this message repeats forever at high rate. There is no
device at any of the reported addresses.
Analysis shows that this is seen if multiple devices have the alert pin
active. Apparently some devices do not support SMBus arbitration correctly.
They keep sending address bits after detecting an address collision and
handle the collision not at all or too late.
Specifically, address 0x0c is seen with ADT7461A at address 0x4c and
ADM1021 at address 0x18 if alert is active on both chips. Address 0x28 is
seen with ADT7483 at address 0x2a and ADT7461 at address 0x4c if alert is
active on both chips.
Once the system is in bad state (alert is set by more than one chip),
it often only recovers by power cycling.
To reduce the impact of this problem, abort the endless loop in
smbus_alert() if the same address is read more than once and not
handled by a driver.
Fixes: b5527a7766f0 ("i2c: Add SMBus alert support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[wsa: it also fixed an interrupt storm in one of my experiments]
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: rebased, moved a comment as well, improved the 'invalid' value]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 37a672be3ae357a0f87fbc00897fa7fcb3d7d782 upstream.
Return an error code if devm_reset_control_get_exclusive() fails.
The current code returns success.
Fixes: 0e864b552b23 ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fea6b5ebb71a2830b042e42de7ae255017ac3ce8 ]
We should allow RXDMA only if the reset was really successful, so clear
the flag after the reset call.
Fixes: 0e864b552b23 ("i2c: rcar: reset controller is mandatory for Gen3+")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea5ea84c9d3570dc06e8fc5ee2273eaa584aa3ac ]
R-Car Gen3+ needs a reset before every controller transfer. That erases
configuration of a potentially in parallel running local target
instance. To avoid this disruption, avoid controller transfers if a
local target is running. Also, disable SMBusHostNotify because it
requires being a controller and local target at the same time.
Fixes: 3b770017b03a ("i2c: rcar: handle RXDMA HW behaviour on Gen3")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b523c46e81ebd621515ab47117f95de197dfcbf ]
So far, we treated Gen4 as Gen3. But we are soon adding FM+ as a Gen4
specific feature, so prepare the code for the new devtype.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: ea5ea84c9d35 ("i2c: rcar: ensure Gen3+ reset does not disturb local targets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e864b552b2302e40b2277629ebac79544a5c433 ]
Initially, we only needed a reset controller to make sure RXDMA works at
least once per transfer. Meanwhile, documentation has been updated. It
now says that a reset has to be performed prior every transaction, even
if it is non-DMA. So, make the reset controller a requirement instead of
being optional. And bail out if resetting fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: ea5ea84c9d35 ("i2c: rcar: ensure Gen3+ reset does not disturb local targets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea01b71b07993d5c518496692f476a3c6b5d9786 ]
Add support for the I2C Bus Interface on R-Car Gen4 SoCs (e.g. R-Car
S4-8) by matching on a family-specific compatible value.
While I2C on R-Car Gen4 does support some extra features (Slave Clock
Stretch Select), for now it is treated the same as I2C on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: removed incorrect "FM+" from commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: ea5ea84c9d35 ("i2c: rcar: ensure Gen3+ reset does not disturb local targets")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd9f5348089b65612e5ca976e2ae22f005340331 ]
I2C core handles the local target for receiving HostNotify alerts. There
is no separate driver bound to that address. That means userspace can
access it if desired, leading to further complications if controllers
are not capable of reading their own local target. Bind the local target
to the dummy driver so it will be marked as "handled by the kernel" if
the HostNotify feature is used. That protects aginst userspace access
and prevents other drivers binding to it.
Fixes: 2a71593da34d ("i2c: smbus: add core function handling SMBus host-notify")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e36c0f20cb1c74c7bd7ea31ba432c1c4a989031 ]
When probing, the hardware is not brought into a known state. This may
be a problem when a hypervisor restarts Linux without resetting the
hardware, leaving an old state running. Make sure the hardware gets
initialized, especially interrupts should be cleared and disabled.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/r/20240702045535.2000393-1-dirk.behme@de.bosch.com
Fixes: 6ccbe607132b ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f63b94be6942ba82c55343e196bd09b53227618e ]
When del_timer_sync() is called in an interrupt context it throws a warning
because of potential deadlock. The timer is used only to exit from
wait_for_completion() after a timeout so replacing the call with
wait_for_completion_timeout() allows to remove the problematic timer and
its related functions altogether.
Fixes: 41561f28e76a ("i2c: New Philips PNX bus driver")
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 355b1513b1e97b6cef84b786c6480325dfd3753d ]
Annotate this variable as __ro_after_init to protect it from being
overwritten later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5a72477273066b5b357801ab2d315ef14949d402 upstream.
Setting IACK bit when core is disabled does not clear the "Interrupt Flag"
bit in the status register, and the interrupt remains pending.
Sometimes it causes failure for the very first message transfer, that is
usually a device probe.
Hence, set IACK bit after core is enabled to clear pending interrupt.
Fixes: 18f98b1e3147 ("[PATCH] i2c: New bus driver for the OpenCores I2C controller")
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cbf3fb5b29e99e3689d63a88c3cddbffa1b8de99 ]
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 5b6d721b266a ("i2c: designware: enable SLAVE in platform module")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Luis Oliveira <lolivei@synopsys.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6d5645e5fc1233a7ba950de4a72981c394a2557 ]
When an I2C adapter acts only as a slave, it should not claim to
support I2C master capabilities.
Fixes: 9d3ca54b550c ("i2c: at91: added slave mode support")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Juergen Fitschen <me@jue.yt>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 91811a31b68d3765b3065f4bb6d7d6d84a7cfc9f ]
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il
Fixes: 4b1acc43331d ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1c9d0f6f7f1dbf29db996bd8e166242843a5f21 ]
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c9453 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e1d6582f483a4dba4ea03445e6f2f05d9de5bcf ]
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: c1c9d0f6f7f1 ("i2c: i801: Fix block process call transactions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19cde9c92b8d3b7ee555d0da3bcb0232d3a784f4 ]
Possible deadlock scenario (on reboot):
rk3x_i2c_xfer_common(polling)
-> rk3x_i2c_wait_xfer_poll()
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock);
...
<rk3x i2c interrupt>
-> rk3x_i2c_irq(0, i2c);
--> spin_lock(&i2c->lock); (deadlock here)
Store the IRQ number and disable/enable it around the polling transfer.
This patch has been tested on NanoPC-T4.
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a3368e1186e3ce8e38f78cbca019622095b1f331 upstream.
Since commit aa49c90894d0 ("i2c: core: Run atomic i2c xfer when
!preemptible"), the whole reboot/power off sequence on non-preempt kernels
is using atomic i2c xfer, as !preemptible() always results to 1.
During device_shutdown(), the i2c might be used a lot and not all busses
have implemented an atomic xfer handler. This results in a lot of
avoidable noise, like:
[ 12.687169] No atomic I2C transfer handler for 'i2c-0'
[ 12.692313] WARNING: CPU: 6 PID: 275 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x118
...
Fix this by allowing non-atomic xfer when the interrupts are enabled, as
it was before.
Link: https://lore.kernel.org/r/20231222230106.73f030a5@yea
Link: https://lore.kernel.org/r/20240102150350.3180741-1-mwalle@kernel.org
Link: https://lore.kernel.org/linux-i2c/13271b9b-4132-46ef-abf8-2c311967bb46@mailbox.org/
Fixes: aa49c90894d0 ("i2c: core: Run atomic i2c xfer when !preemptible")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Tor Vic <torvic9@mailbox.org>
[wsa: removed a comment which needs more work, code is ok]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b4cc1cbba5195a4dd497cf2f8f09e7807977d543 ]
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350bb2 ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f726eaa787e9f9bc858c902d18a09af6bcbfcdaf ]
When running on a many core ARM64 server, errors were
happening in the ISR that looked like corrupted memory. These
corruptions would fix themselves if small delays were inserted
in the ISR. Errors reported by the driver included "i2c_designware
APMC0D0F:00: i2c_dw_xfer_msg: invalid target address" and
"i2c_designware APMC0D0F:00:controller timed out" during
in-band IPMI SSIF stress tests.
The problem was determined to be memory writes in the driver were not
becoming visible to all cores when execution rapidly shifted between
cores, like when a register write immediately triggers an ISR.
Processors with weak memory ordering, like ARM64, make no
guarantees about the order normal memory writes become globally
visible, unless barrier instructions are used to control ordering.
To solve this, regmap accessor functions configured by this driver
were changed to use non-relaxed forms of the low-level register
access functions, which include a barrier on platforms that require
it. This assures memory writes before a controller register access are
visible to all cores. The community concluded defaulting to correct
operation outweighed defaulting to the small performance gains from
using relaxed access functions. Being a low speed device added weight to
this choice of default register access behavior.
Signed-off-by: Jan Bottorff <janb@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f78ca48a8ba9cdec96e8839351e49eec3233b177 upstream.
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8183fa10c25c7b3c20670bf2b430ddcc1ee03c0 upstream.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa49c90894d06e18a1ee7c095edbd2f37c232d02 upstream.
Since bae1d3a05a8b, i2c transfers are non-atomic if preemption is
disabled. However, non-atomic i2c transfers require preemption (e.g. in
wait_for_completion() while waiting for the DMA).
panic() calls preempt_disable_notrace() before calling
emergency_restart(). Therefore, if an i2c device is used for the
restart, the xfer should be atomic. This avoids warnings like:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Use !preemptible() instead, which is basically the same check as
pre-v5.2.
Fixes: bae1d3a05a8b ("i2c: core: remove use of in_atomic()")
Cc: stable@vger.kernel.org # v5.2+
Suggested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-2-18699d5dcd76@skidata.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5ac61d26b8baff5b2e5a9f3dc1ef63297e4b53e7 ]
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 54f1840ddee9bbdc8dd89fbbfdfa632401244146 upstream.
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c896ff2dd8f30a6b0a922c83a96f6d43f05f0e92 upstream.
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6bfe ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fb118de5003028ad092a4e66fc6d07b86c3bc94 upstream.
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dc0ec46f6e7511fc4fdf6b6cda439382bc957f1 upstream.
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3171d37b58a76e1febbf3f4af2d06234a98cf88b upstream.
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0de ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b13e59e74ff71a1004e0508107e91e9a84fd7388 ]
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3914784553f68c931fc666dbe7e86fe881aada38 upstream.
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 92e73d807b68b2214fcafca4e130b5300a9d4b3c ]
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c0195fa9a9e263df204963f88a22b21688ffb66 ]
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac030 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fee465150b458351b6d9b9f66084f3cc3022b88b upstream.
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb98 ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69f035c480d76f12bf061148ccfd578e1099e5fc upstream.
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4caf4cb1eaed469742ef719f2cc024b1ec3fa9e6 upstream.
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a1038728037 ("i2c: iproc: add NIC I2C support")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 05f933d5f7318b03ff2028c1704dc867ac16f2c7 ]
Since commit 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba
driver"), there is no more request_mem_region() call in this driver.
So remove the release_mem_region() call from the remove function which is
likely a left over.
Fixes: 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba driver")
Cc: <stable@vger.kernel.org> # v3.6+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c7174db4cdd111e10d19eed5c36fd978a14c8a2 ]
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c5d33fff0d375e4ab7c4261dc62a286babbb4c6 ]
The err_no_mem goto label doesn't do anything. Remove it.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06e989578232da33a7fe96b04191b862af8b2cec ]
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding
size determination a bit safer according to the Linux coding style
convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b3b21a8542fd2fb6ffc61bc13b9419f0c58ebad ]
These issues were detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cd9489623c29aa2f8cc07088168afb6e0d5ef06d upstream.
Smatch Warns:
drivers/i2c/busses/i2c-qup.c:1784 qup_i2c_probe()
warn: missing unwind goto?
The goto label "fail_runtime" and "fail" will disable qup->pclk,
but here qup->pclk failed to obtain, in order to be consistent,
change the direct return to goto label "fail_dma".
Fixes: 9cedf3b2f099 ("i2c: qup: Add bam dma capabilities")
Signed-off-by: Shuai Jiang <d202180596@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb6e45c9a0ad9e0f8664fd06db0227d185dc76ab ]
In xiic_process, it is possible that error events such as arbitration
lost or TX error can be raised in conjunction with other interrupt flags
such as TX FIFO empty or bus not busy. Error events result in the
controller being reset and the error returned to the calling request,
but the function could potentially try to keep handling the other
events, such as by writing more messages into the TX FIFO. Since the
transaction has already failed, this is not helpful and will just cause
issues.
This problem has been present ever since:
commit 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
which allowed non-error events to be handled after errors, but became
more obvious after:
commit 743e227a8959 ("i2c: xiic: Defer xiic_wakeup() and
__xiic_start_xfer() in xiic_process()")
which reworked the code to add a WARN_ON which triggers if both the
xfer_more and wakeup_req flags were set, since this combination is
not supposed to happen, but was occurring in this scenario.
Skip further interrupt handling after error flags are detected to avoid
this problem.
Fixes: 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 743e227a895923c37a333eb2ebf3e391f00c406d ]
The __xiic_start_xfer() manipulates the interrupt flags, xiic_wakeup()
may result in return from xiic_xfer() early. Defer both to the end of
the xiic_process() interrupt thread, so that they are executed after
all the other interrupt bits handling completed and once it completely
safe to perform changes to the interrupt bits in the hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: cb6e45c9a0ad ("i2c: xiic: Don't try to handle more interrupt events after error")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e69b9bc170c6d93ee375a5cbfd15f74c0fb59bdd ]
Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
