| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 37f071ec327b04c83d47637c5e5c2199b39899ca ]
The i2c-mlxbf.c driver is currently broken because there is a bug
in the calculation of the frequency. core_f, core_r and core_od
are components read from hardware registers and are used to
compute the frequency used to compute different timing parameters.
The shifting mechanism used to get core_f, core_r and core_od is
wrong. Use FIELD_GET to mask and shift the bitfields properly.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de24aceb07d426b6f1c59f33889d6a964770547b ]
memcpy() is called in a loop while 'operation->length' upper bound
is not checked and 'data_idx' also increments.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2a5be6d1340c0fefcee8a6489cff7fd88a0d5b85 ]
Correct the base address used during io write.
This bug had no impact over the overall functionality of the read and write
transactions. MLXBF_I2C_CAUSE_OR_CLEAR=0x18 so writing to (smbus->io + 0x18)
instead of (mst_cause->ioi + 0x18) actually writes to the sc_low_timeout
register which just sets the timeout value before a read/write aborts.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 085aacaa73163f4b8a89dec24ecb32cfacd34017 ]
pm_runtime_get_sync() returning 1 also means the device is powered. So
resetting the chip registers in .remove() is possible and should be
done.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d98bdd3a5b50 ("i2c: imx: Make sure to unregister adapter on remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d98bdd3a5b50446d8e010be5b04ce81c4eabf728 upstream.
If for whatever reasons pm_runtime_resume_and_get() fails and .remove() is
exited early, the i2c adapter stays around and the irq still calls its
handler, while the driver data and the register mapping go away. So if
later the i2c adapter is accessed or the irq triggers this results in
havoc accessing freed memory and unmapped registers.
So unregister the software resources even if resume failed, and only skip
the hardware access in that case.
Fixes: 588eb93ea49f ("i2c: imx: add runtime pm support to improve the performance")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6435319c34704994e19b0767f6a4e6f37439867b ]
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9fdf6d97f03035ad5298e2d1635036c74c2090ed ]
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4c72c06c367758a14f227c847f9d623f1994ecf ]
Free the adap structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 611e12ea0f12 ("i2c: core: manage i2c bus device refcount in i2c_[get|put]_adapter")
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
[wsa: added comment to the code, added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d7aa1b149b8fc04d802879cf4662010aa4a42deb ]
Correct the slave transaction logic to be compatible with the generic
slave backend driver.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 47d506d1a28fd10a9fb1f33df5622d88fae72095 ]
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ca8ca873d454635c20d508261bfc0081af75cf8 ]
Problems were observed on the Xilinx ZynqMP platform with large I2C reads.
When a read of 277 bytes was performed, the controller NAKed the transfer
after only 252 bytes were transferred and returned an ENXIO error on the
transfer.
There is some code in cdns_i2c_master_isr to handle this case by resetting
the transfer count in the controller before it reaches 0, to allow larger
transfers to work, but it was conditional on the CDNS_I2C_BROKEN_HOLD_BIT
quirk being set on the controller, and ZynqMP uses the r1p14 version of
the core where this quirk is not being set. The requirement to do this to
support larger reads seems like an inherently required workaround due to
the core only having an 8-bit transfer size register, so it does not
appear that this should be conditional on the broken HOLD bit quirk which
is used elsewhere in the driver.
Remove the dependency on the CDNS_I2C_BROKEN_HOLD_BIT for this transfer
size reset logic to fix this problem.
Fixes: 63cab195bf49 ("i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3501f0c663063513ad604fb1b3f06af637d3396d ]
This patch ensures that the clock notifier is unregistered
when driver probe is returning error.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Satish Nagireddy <satish.nagireddy@getcruise.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27071b5cbca59d8e8f8750c199a6cbf8c9799963 ]
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit c62ebb3d5f0d ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit b33af11de236 ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: c62ebb3d5f0d ("i2c: designware: Add support for an interface clock")
Fixes: b33af11de236 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ba12b56b9b844b83ed54fb7ed59fb0eb41e4045 ]
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96789dce043f5bff8b7d62aa28d52a7c59403a84 ]
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fe2ec59db1a7569e18594b9c0cf1f4f1afd498e ]
We have to take care of ID_P_PM_BLOCKED when bailing out during probe.
Fixes: 7ee24eb508d6 ("i2c: rcar: disable PM in multi-master mode")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5222d408de2a88e6b206c38217b48d092184553 ]
On some platforms in rare cases (1 to 100,000 transactions),
the i2c gets a spurious interrupt which means that we enter an interrupt
but in the interrupt handler we don't find any status bit that points to
the reason we got this interrupt.
This may be a case of a rare HW issue or signal integrity issue that is
still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is not
enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the
transaction.
On next xmit transaction if the bus is still busy the master will issue a
recovery process before issuing the new transaction.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea9f8426d17620214ee345ffb77ee6cc196ff14f ]
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always
incorrect, but simply didn't cause a visible error on the 32-bit machine.
On the 64-bit machine, the kernel message reports that ESR value is
0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that
it's the alignment fault.
SMBnCTL3's address is 0xE.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 288b204492fddf28889cea6dc95a23976632c7a0 ]
Use adap.timeout for timeout calculation instead of hard-coded
value of 35ms.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6977262c2eee111645668fe9e235ef2f5694abf7 ]
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8bf ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03fbb903c8bf7e53e101e8d9a7b261264317c411 ]
The supplied buffer might be on the stack and we get the following error
message:
[ 3.312058] at91_i2c e0070600.i2c: rejecting DMA map of vmalloc memory
Use i2c_{get,put}_dma_safe_msg_buf() to get a DMA-able memory region if
necessary.
Fixes: 60937b2cdbf9 ("i2c: at91: add dma support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03a35bc856ddc09f2cc1f4701adecfbf3b464cb3 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17a0f3acdc6ec8b89ad40f6e22165a4beee25663 ]
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2537c98a8a3b57002e54a262d180b9490bc7190 ]
Fix the missing clk_disable_unprepare() before return
from mtk_i2c_probe() in the error handling case.
Fixes: d04913ec5f89 ("i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bd8963e602c77adc76dbbbfc3417c3cf14fed76b upstream.
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1a22aabf20adf89cb216f566913196128766f25b ]
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d44 ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cb13aa16f34f794a9cee2626862af8a95f0f0ee9 ]
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa490 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d366c2f9df8279df2adbb60471f86fc40a1c39e ]
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598cdc ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fd269e74f2feec973f45ee11d822faeda4fe284 ]
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5de717974005fcad2502281e9f82e139ca91f4bb ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b0dcb3882c8f08bdeafa03adb4487e104d26050 ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9495b9b31abe525ebd93da58de2c88b9f66d3a0e ]
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 834cea3a252ed4847db076a769ad9efe06afe2d5 upstream.
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02a4a69667a2ad32f3b52ca906f19628fbdd8a01 upstream.
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0d48505a1d68e27220369e2dd1e3573a2f362d2 upstream.
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d52097010078c1844348dc0e467305e5f90fd317 ]
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebe82cf92cd4825c3029434cabfcd2f1780e64be ]
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit effa453168a7eeb8a562ff4edc1dbf9067360a61 ]
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb436283e25aaf1533ce061605d23a9564447bdf ]
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655f2 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ]
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b12764695c3fcade145890b67f82f8b139174cc7 upstream.
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31b90a95ccbbb4b628578ac17e3b3cc8eeacfe31 upstream.
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b933d1faf8fa30d16171bcff404e39c41b2a7c84 upstream.
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c21d02ca469574d2082379db52d1a27b99eed0c upstream.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7f98960c046ee1136e7096aee168eda03aef8a5d ]
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372e4 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8228aea5a19d5111a7bf44f7de6749d1f5d487a ]
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f810 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3bce7703c7ba648bd9e174dc1413f422b7998833 ]
In the commit be5ce0e97cc7 ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97cc7 ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6558b646ce1c2a872fe1c2c7cb116f05a2c1950f ]
acpi_i2c_find_adapter_by_handle() calls bus_find_device() which takes a
reference on the adapter which is never released which will result in a
reference count leak and render the adapter unremovable. Make sure to
put the adapter after creating the client in the same manner that we do
for OF.
Fixes: 525e6fabeae2 ("i2c / ACPI: add support for ACPI reconfigure notifications")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: fixed title]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 661e8a88e8317eb9ffe69c69d6cb4876370fe7e2 ]
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2b ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58fb7c643d346e2364404554f531cfa6a1a3917c ]
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39ea ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
