| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 89c6efa61f5709327ecfa24bff18e57a4e80c7fa upstream.
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.
It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.
This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.
Call Trace:
[<ffffffff8139f695>] dump_stack+0x67/0x92
[<ffffffff811802a4>] panic+0xc5/0x1eb
[<ffffffff810ecb5f>] ? vprintk_default+0x1f/0x30
[<ffffffff817456d3>] ? i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff8109a68b>] __stack_chk_fail+0x1b/0x20
[<ffffffff817456d3>] i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff81745aed>] i2cdev_ioctl+0x4d/0x1e0
[<ffffffff811f761a>] do_vfs_ioctl+0x2ba/0x490
[<ffffffff81336e43>] ? security_file_ioctl+0x43/0x60
[<ffffffff811f7869>] SyS_ioctl+0x79/0x90
[<ffffffff81a22e97>] entry_SYSCALL_64_fastpath+0x12/0x6a
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5165da5923d6c7df6f2927b0113b2e4d9288661e upstream.
Since v4.9 i2c-tiny-usb generates the below call trace
and longer works, since it can't communicate with the
USB device. The reason is, that since v4.9 the USB
stack checks, that the buffer it should transfer is DMA
capable. This was a requirement since v2.2 days, but it
usually worked nevertheless.
[ 17.504959] ------------[ cut here ]------------
[ 17.505488] WARNING: CPU: 0 PID: 93 at drivers/usb/core/hcd.c:1587 usb_hcd_map_urb_for_dma+0x37c/0x570
[ 17.506545] transfer buffer not dma capable
[ 17.507022] Modules linked in:
[ 17.507370] CPU: 0 PID: 93 Comm: i2cdetect Not tainted 4.11.0-rc8+ #10
[ 17.508103] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[ 17.509039] Call Trace:
[ 17.509320] ? dump_stack+0x5c/0x78
[ 17.509714] ? __warn+0xbe/0xe0
[ 17.510073] ? warn_slowpath_fmt+0x5a/0x80
[ 17.510532] ? nommu_map_sg+0xb0/0xb0
[ 17.510949] ? usb_hcd_map_urb_for_dma+0x37c/0x570
[ 17.511482] ? usb_hcd_submit_urb+0x336/0xab0
[ 17.511976] ? wait_for_completion_timeout+0x12f/0x1a0
[ 17.512549] ? wait_for_completion_timeout+0x65/0x1a0
[ 17.513125] ? usb_start_wait_urb+0x65/0x160
[ 17.513604] ? usb_control_msg+0xdc/0x130
[ 17.514061] ? usb_xfer+0xa4/0x2a0
[ 17.514445] ? __i2c_transfer+0x108/0x3c0
[ 17.514899] ? i2c_transfer+0x57/0xb0
[ 17.515310] ? i2c_smbus_xfer_emulated+0x12f/0x590
[ 17.515851] ? _raw_spin_unlock_irqrestore+0x11/0x20
[ 17.516408] ? i2c_smbus_xfer+0x125/0x330
[ 17.516876] ? i2c_smbus_xfer+0x125/0x330
[ 17.517329] ? i2cdev_ioctl_smbus+0x1c1/0x2b0
[ 17.517824] ? i2cdev_ioctl+0x75/0x1c0
[ 17.518248] ? do_vfs_ioctl+0x9f/0x600
[ 17.518671] ? vfs_write+0x144/0x190
[ 17.519078] ? SyS_ioctl+0x74/0x80
[ 17.519463] ? entry_SYSCALL_64_fastpath+0x1e/0xad
[ 17.519959] ---[ end trace d047c04982f5ac50 ]---
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Till Harbaum <till@harbaum.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 30f939feaeee23e21391cfc7b484f012eb189c3c upstream.
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 147b36d5b70c083cc76770c47d60b347e8eaf231 upstream.
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 371a015344b6e270e7e3632107d9554ec6d27a6b upstream.
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit cdc5a3110e7c3ae793f367285789a6bc39c962dc upstream.
Adding Intel codename Lewisburg platform device IDs for SMBus.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2b630df721ee4c286d286ab5d5d958d34c86f067 upstream.
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dd77f423e516293c37c2370b44fd700900409c48 upstream.
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 84d7f2ebd70d36e9d83e0973d2f4dac56a671f4f upstream.
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2: no FEATURE_IRQ or FEATURE_TCO here]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3eee1799aed90e990e02a73a89bfcff1982c74dd upstream.
Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3e27a8445c21f8056517f188303827450590d868 upstream.
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 39e8e30ee544a62c148033d64a979028b958ca05 upstream.
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b299de839157852c563b9f133c8b7e630545a9c3 upstream.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ce3161106ab57afbfbe1c33d95bf4a569405983a upstream.
A long name broke the alignment, shift the columns a bit to fix it and
make the table look nice again. While we're here, switch to the
standard comment style to make checkpatch happy, and use tabs instead
of spaces for column alignment.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2: "Interrupt processing" isn't mentioned]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1b31e9b76ef8c62291e698dfdb973499986a7f68 upstream.
Add Device ID of Intel BayTrail SMBus Controller.
Signed-off-by: Chew, Kean ho <kean.ho.chew@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit afc659241258b40b683998ec801d25d276529f43 upstream.
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f39901c1befa556bc91902516a3e2e460000b4a8 upstream.
This patch adds the i801 SMBus Controller DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a3fc0ff00a46c4b32e7214961a5be9a1dc39b60e upstream.
This patch adds the SMBus Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c2db409cbc8751ccc7e6d2cc2e41af0d12ea637f upstream.
This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9ea359f7314132cbcb5a502d2d8ef095be1f45e4 upstream.
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ce78cc071f5f541480e381cc0241d37590041a9d upstream.
Don't unmark the device as suspended until after it's been re-setup.
The main race would be w.r.t. an i2c driver that gets resumed at the same
time (asyncronously), that is allowed to do a transfer since suspended
is set to 0 before reinit, but really should have seen the -EIO return
instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 47bb27e78867997040a228328f2a631c3c7f2c82 upstream.
There have been "i2c_designware 80860F41:00: controller timed out" errors
on a number of Baytrail platforms. The issue is caused by incorrect value in
Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled.
This causes call to __i2c_dw_enable() to immediately start the transfer which
leads to timeout. There are 3 failure modes observed:
1. Failure in S0 to S3 resume path
The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start
the first transaction after resuming from system sleep, TX_EMPTY interrupt
is already unmasked because of the hardware default.
2. Failure in normal operational path
This failure happens rarely and is hard to reproduce. Debug trace showed that
DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant
TX_EMPTY was unmasked.
3. Failure in S3 to S0 suspend path
This failure also happens rarely and is hard to reproduce. Adding debug trace
that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR
call trace we could conclude TX_EMPTY was unmasked when problem occurred.
The patch masks all interrupts before the controller is enabled to resolve the
faulty DW_IC_INTR_MASK conditions.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: improved the comment and removed typo in commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 032f708bc4f6da868ec49dac48ddf3670d8035d3 upstream.
The locations of SMBus register base address and enablement bit are changed
from AMD ML, which need this patch to be supported.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2:
- Adjust context
- Aux bus support is not included]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b996ac90f595dda271cbd858b136b45557fc1a57 upstream.
To add AMD CZ SMBus controller device ID.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2a2d95e9d6d29e726cc294b65391917ed2e32bf4 upstream.
If the I2C bus is put to a low power state by an ACPI method it might pull
the SDA line low (as its power is removed). Once the bus is put to full
power state again, the SDA line is pulled back to high. This transition
looks like a STOP condition from the controller point-of-view which sets
STOP detected bit in its status register causing the driver to fail
subsequent transfers.
Fix this by always clearing all interrupts before we start a transfer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c39e8e4354ce4daf23336de5daa28a3b01f00aa6 upstream.
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 132c803f7b70b17322579f6f4f3f65cf68e55135 upstream.
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2:
- Adjust context
- Keep calling clk_enable() directly]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4a8f1ddde942e232387e6129ce4f4c412e43802f upstream.
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 062737fb6d90c632439b1f77ad6a4965cfc84a20 upstream.
Add the SMBus controller device IDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
CONFIG_I2C_DESIGNWARE_PCI=y
commit e68bb91baa0bb9817567bd45d560919e8e26373b upstream.
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9868a060ccf769c08ec378a9829137e272e9a92c upstream.
The freed IRQ is not necessary the one requested in probe.
Even if it was, with two or more i2c-controllers it will fails anyway.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c889e91d2cc22123f20f40dde0c0a91856a20eea upstream.
The notification of the transfer complete by calling complete()
should be done after clearing all interrupt status.
This avoids the race condition of misconfigure the i2c controller
in multi-core environment.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8a52f9f347da721b199b7f9dcc0168bbe7d0baae upstream.
Currently, during i2c works alone, wait-event timeout is not occurred.
However, as CPU load increases, timeout occurs frequently.
So, I modified like this patch.
Modifying like this patch, I've never seen the timeout event with high
load test.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6c557cfee08751d22aed34840f389b846f0f4508 upstream.
In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[wsa: reworded commit header slightly]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8ee161ce5e0cfc689eb677f227a6248191165fac upstream.
When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.
To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 844990daa2e69a4258049ba9c2bae1180657dac3 upstream.
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff35e8b18984ad2a82cbd259fc07f0be4b34b1aa upstream.
This patch modified the setting value of
I2C Bus Transfer Rate Setting Counter regisrer.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2727b1753934e154931d6b3bdf20c9b2398457a2 upstream.
Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7c1f59c9d5caf3a84f35549b5d58f3c055a68da5 upstream.
When adding checks for ACPI resource conflicts to many bus drivers,
not enough attention was paid to the error paths, and for several
drivers this causes 0 to be returned on error in some cases. Fix this
by properly returning a non-zero value on every error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Before registering an adapter to i2c subsystem, we need make sure
driver is ready for incoming i2c xfer, becasue the i2c_add_adapter()
may trigger a i2c device driver's proble function which may start
some real i2c xfer. I met this issue when integrating a TSC2007 i2c
touch screen device with the i2c-eg20t driver.
This patch will call request_irq() and hw init before calling
i2c_add_adapter().
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Currently the fifo depth is set to zero for OMAP4 which disables
the FIFO usage. This patch enables the FIFO usage for I2C transactions
on OMAP4 also.
Tested on omap4430 and 3430.
Tested-and-Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
s3c24xx_i2c_parse_dt_gpio is called when cfg_gpio is not defined
in the platform data of the i2c device. When DT is not enabled,
the above function always returns -EINVAL. Since there can be
some i2c devices which don't need to configure any gpio lines,
the probe of such devices would fail here. Changing the default
return value to success would fix this issue.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Be a bit more friendly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7182/1: ARM cpu topology: fix warning
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
ARM: 7176/1: cpu_pm: register GIC PM notifier only once
ARM: 7175/1: add subname parameter to mfp_set_groupg callers
ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
ARM: 7170/2: fix compilation breakage in entry-armv.S
ARM: 7168/1: use cache type functions for arch_get_unmapped_area
ARM: perf: check that we have a platform device when reserving PMU
ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
ARM: 7163/2: PL330: Only register usable channels
ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
ARM: 7161/1: errata: no automatic store buffer drain
ARM: perf: initialise used_mask for fake PMU during validation
ARM: PMU: remove pmu_init declaration
ARM: PMU: re-export release_pmu symbol to modules
|
|
commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900"
adds subname parameter for mfp_set_groupg.
Thus add subname parameter to the callers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning
drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
The wrong bits were put on the wire, fix that.
This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
MIPS: O32: Provide definition of registers ta0 .. ta3.
MIPS: perf: Add Octeon support for hardware perf.
MIPS: perf: Add support for 64-bit perf counters.
MIPS: perf: Reorganize contents of perf support files.
MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
MIPS: Add accessor macros for 64-bit performance counter registers.
MIPS: Add probes for more Octeon II CPUs.
MIPS: Add more CPU identifiers for Octeon II CPUs.
MIPS: XLR, XLS: Add comment for smp setup
MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
MIPS: JZ4740: GPIO: Simplify IRQ demuxer
MIPS: JZ4740: Use generic irq chip
MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
MIPS: Alchemy: kill au1xxx.h header
MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
MIPS: Alchemy: Redo PCI as platform driver
MIPS: Alchemy: more base address cleanup
MIPS: Alchemy: rewrite USB platform setup.
MIPS: Alchemy: abstract USB block control register access
...
Fix up trivial conflicts in:
arch/mips/alchemy/devboards/db1x00/platform.c
drivers/ide/Kconfig
drivers/mmc/host/au1xmmc.c
drivers/video/Kconfig
sound/mips/Kconfig
|
