summaryrefslogtreecommitdiff
path: root/drivers/i2c/busses
AgeCommit message (Collapse)AuthorFilesLines
2021-12-22i2c: rk3x: Handle a spurious start completion interrupt flagOndrej Jirman1-2/+2
[ Upstream commit 02fe0fbd8a21e183687925c3a266ae27dda9840f ] In a typical read transfer, start completion flag is being set after read finishes (notice ipd bit 4 being set): trasnfer poll=0 i2c start rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10 i2c read rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b i2c stop rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33 This causes I2C transfer being aborted in polled mode from a stop completion handler: trasnfer poll=1 i2c start rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10 i2c read rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0 rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b i2c stop rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13 i2c stop rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10 Clearing the START flag after read fixes the issue without any obvious side effects. This issue was dicovered on RK3566 when adding support for powering off the RK817 PMIC. Signed-off-by: Ondrej Jirman <megous@megous.com> Reviewed-by: John Keeping <john@metanate.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-12-08i2c: stm32f7: stop dma transfer in case of NACKAlain Volmat1-2/+7
commit 31b90a95ccbbb4b628578ac17e3b3cc8eeacfe31 upstream. In case of receiving a NACK, the dma transfer should be stopped to avoid feeding data into the FIFO. Also ensure to properly return the proper error code and avoid waiting for the end of the dma completion in case of error happening during the transmission. Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support") Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-08i2c: stm32f7: recover the bus on access timeoutAlain Volmat1-0/+2
commit b933d1faf8fa30d16171bcff404e39c41b2a7c84 upstream. When getting an access timeout, ensure that the bus is in a proper state prior to returning the error. Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver") Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-26i2c: xlr: Fix a resource leak in the error handling path of 'xlr_i2c_probe()'Christophe JAILLET1-1/+5
[ Upstream commit 7f98960c046ee1136e7096aee168eda03aef8a5d ] A successful 'clk_prepare()' call should be balanced by a corresponding 'clk_unprepare()' call in the error handling path of the probe, as already done in the remove function. More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is also already called. So just the unprepare step has still to be done. Update the error handling path accordingly. Fixes: 75d31c2372e4 ("i2c: xlr: add support for Sigma Designs controller variant") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-22i2c: mt65xx: fix IRQ checkSergey Shtylyov1-1/+1
[ Upstream commit 58fb7c643d346e2364404554f531cfa6a1a3917c ] Iff platform_get_irq() returns 0, the driver's probe() method will return 0 early (as if the method's call was successful). Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always override that decision... Fixes: ce38815d39ea ("I2C: mediatek: Add driver for MediaTek I2C controller") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Reviewed-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-22i2c: s3c2410: fix IRQ checkSergey Shtylyov1-1/+1
[ Upstream commit d6840a5e370b7ea4fde16ce2caf431bcc87f9a75 ] Iff platform_get_irq() returns 0, the driver's probe() method will return 0 early (as if the method's call was successful). Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always override that decision... Fixes: e0d1ec97853f ("i2c-s3c2410: Change IRQ to be plain integer.") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-22i2c: iop3xx: fix deferred probingSergey Shtylyov1-4/+2
[ Upstream commit a1299505162ad00def3573260c2c68b9c8e8d697 ] When adding the code to handle platform_get_irq*() errors in the commit 489447380a29 ("handle errors returned by platform_get_irq*()"), the actual error code was enforced to be -ENXIO in the driver for some strange reason. This didn't matter much until the deferred probing was introduced -- which requires an actual error code to be propagated upstream from the failure site. While fixing this, also stop overriding the errors from request_irq() to -EIO (done since the pre-git era). Fixes: 489447380a29 ("[PATCH] handle errors returned by platform_get_irq*()") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-22i2c: highlander: add IRQ checkSergey Shtylyov1-1/+1
[ Upstream commit f16a3bb69aa6baabf8f0aca982c8cf21e2a4f6bc ] The driver is written as if platform_get_irq() returns 0 on errors (while actually it returns a negative error code), blithely passing these error codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with -EINVAL. Add the necessary error check to the pre-existing *if* statement forcing the driver into the polling mode... Fixes: 4ad48e6ab18c ("i2c: Renesas Highlander FPGA SMBus support") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-06-30i2c: robotfuzz-osif: fix control-request directionsJohan Hovold1-2/+2
commit 4ca070ef0dd885616ef294d269a9bf8e3b258e1a upstream. The direction of the pipe argument must match the request-type direction bit or control requests may fail depending on the host-controller-driver implementation. Control transfers without a data stage are treated as OUT requests by the USB stack and should be using usb_sndctrlpipe(). Failing to do so will now trigger a warning. Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously used the osif_usb_read() helper and set the IN direction bit. Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com Fixes: 83e53a8f120f ("i2c: Add bus driver for for OSIF USB i2c device.") Cc: stable@vger.kernel.org # 3.14 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-16i2c: mpc: implement erratum A-004447 workaroundChris Packham1-1/+78
[ Upstream commit 8f0cdec8b5fd94135d643662506ee94ae9e98785 ] The P2040/P2041 has an erratum where the normal i2c recovery mechanism does not work. Implement the alternative recovery mechanism documented in the P2040 Chip Errata Rev Q. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-06-16i2c: mpc: Make use of i2c_recover_bus()Chris Packham1-2/+16
[ Upstream commit 65171b2df15eb7545431d75c2729b5062da89b43 ] Move the existing calls of mpc_i2c_fixup() to a recovery function registered via bus_recovery_info. This makes it more obvious that recovery is supported and allows for a future where recovery is triggered by the i2c core. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-06-03i2c: i801: Don't generate an interrupt on bus resetJean Delvare1-4/+2
commit e4d8716c3dcec47f1557024add24e1f3c09eb24b upstream. Now that the i2c-i801 driver supports interrupts, setting the KILL bit in a attempt to recover from a timed out transaction triggers an interrupt. Unfortunately, the interrupt handler (i801_isr) is not prepared for this situation and will try to process the interrupt as if it was signaling the end of a successful transaction. In the case of a block transaction, this can result in an out-of-range memory access. This condition was reproduced several times by syzbot: https://syzkaller.appspot.com/bug?extid=ed71512d469895b5b34e https://syzkaller.appspot.com/bug?extid=8c8dedc0ba9e03f6c79e https://syzkaller.appspot.com/bug?extid=c8ff0b6d6c73d81b610e https://syzkaller.appspot.com/bug?extid=33f6c360821c399d69eb https://syzkaller.appspot.com/bug?extid=be15dc0b1933f04b043a https://syzkaller.appspot.com/bug?extid=b4d3fd1dfd53e90afd79 So disable interrupts while trying to reset the bus. Interrupts will be enabled again for the following transaction. Fixes: 636752bcb517 ("i2c-i801: Enable IRQ for SMBus transactions") Reported-by: syzbot+b4d3fd1dfd53e90afd79@syzkaller.appspotmail.com Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-06-03i2c: s3c2410: fix possible NULL pointer deref on read message after writeKrzysztof Kozlowski1-0/+3
commit 24990423267ec283b9d86f07f362b753eb9b0ed5 upstream. Interrupt handler processes multiple message write requests one after another, till the driver message queue is drained. However if driver encounters a read message without preceding START, it stops the I2C transfer as it is an invalid condition for the controller. At least the comment describes a requirement "the controller forces us to send a new START when we change direction". This stop results in clearing the message queue (i2c->msg = NULL). The code however immediately jumped back to label "retry_write" which dereferenced the "i2c->msg" making it a possible NULL pointer dereference. The Coverity analysis: 1. Condition !is_msgend(i2c), taking false branch. if (!is_msgend(i2c)) { 2. Condition !is_lastmsg(i2c), taking true branch. } else if (!is_lastmsg(i2c)) { 3. Condition i2c->msg->flags & 1, taking true branch. if (i2c->msg->flags & I2C_M_RD) { 4. write_zero_model: Passing i2c to s3c24xx_i2c_stop, which sets i2c->msg to NULL. s3c24xx_i2c_stop(i2c, -EINVAL); 5. Jumping to label retry_write. goto retry_write; 6. var_deref_model: Passing i2c to is_msgend, which dereferences null i2c->msg. if (!is_msgend(i2c)) {" All previous calls to s3c24xx_i2c_stop() in this interrupt service routine are followed by jumping to end of function (acknowledging the interrupt and returning). This seems a reasonable choice also here since message buffer was entirely emptied. Addresses-Coverity: Explicit null dereferenced Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-22i2c: sh7760: fix IRQ error pathSergey Shtylyov1-1/+1
[ Upstream commit 92dfb27240fea2776f61c5422472cb6defca7767 ] While adding the invalid IRQ check after calling platform_get_irq(), I managed to overlook that the driver has a complex error path in its probe() method, thus a simple *return* couldn't be used. Use a proper *goto* instead! Fixes: e5b2e3e74201 ("i2c: sh7760: add IRQ check") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-05-22i2c: sh7760: add IRQ checkSergey Shtylyov1-1/+4
[ Upstream commit e5b2e3e742015dd2aa6bc7bcef2cb59b2de1221c ] The driver neglects to check the result of platform_get_irq()'s call and blithely passes the negative error codes to devm_request_irq() (which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original error code. Stop calling devm_request_irq() with invalid IRQ #s. Fixes: a26c20b1fa6d ("i2c: Renesas SH7760 I2C master driver") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-05-22i2c: jz4780: add IRQ checkSergey Shtylyov1-1/+4
[ Upstream commit c5e5f7a8d931fb4beba245bdbc94734175fda9de ] The driver neglects to check the result of platform_get_irq()'s call and blithely passes the negative error codes to devm_request_irq() (which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original error code. Stop calling devm_request_irq() with invalid IRQ #s. Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-05-22i2c: emev2: add IRQ checkSergey Shtylyov1-1/+4
[ Upstream commit bb6129c32867baa7988f7fd2066cf18ed662d240 ] The driver neglects to check the result of platform_get_irq()'s call and blithely passes the negative error codes to devm_request_irq() (which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original error code. Stop calling devm_request_irq() with invalid IRQ #s. Fixes: 5faf6e1f58b4 ("i2c: emev2: add driver") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-05-22i2c: cadence: add IRQ checkSergey Shtylyov1-1/+4
[ Upstream commit 5581c2c5d02bc63a0edb53e061c8e97cd490646e ] The driver neglects to check the result of platform_get_irq()'s call and blithely passes the negative error codes to devm_request_irq() (which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original error code. Stop calling devm_request_irq() with invalid IRQ #s. Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-17i2c: rcar: optimize cacheline to minimize HW race conditionWolfram Sang1-1/+1
[ Upstream commit 25c2e0fb5fefb8d7847214cf114d94c7aad8e9ce ] 'flags' and 'io' are needed first, so they should be at the beginning of the private struct. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-03-04i2c: brcmstb: Fix brcmstd_send_i2c_cmd conditionMaxime Ripard1-1/+1
[ Upstream commit a1858ce0cfe31368b23ba55794e409fb57ced4a4 ] The brcmstb_send_i2c_cmd currently has a condition that is (CMD_RD || CMD_WR) which always evaluates to true, while the obvious fix is to test whether the cmd variable passed as parameter holds one of these two values. Fixes: dd1aa2524bc5 ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver") Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-02-23i2c: stm32f7: fix configuration of the digital filterAlain Volmat1-1/+10
[ Upstream commit 3d6a3d3a2a7a3a60a824e7c04e95fd50dec57812 ] The digital filter related computation are present in the driver however the programming of the filter within the IP is missing. The maximum value for the DNF is wrong and should be 15 instead of 16. Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver") Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-01-27i2c: octeon: check correct size of maximum RECV_LEN packetWolfram Sang1-1/+1
[ Upstream commit 1b2cfa2d1dbdcc3b6dba1ecb7026a537a1d7277f ] I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the SMBus 2.0 specs. No reason to add one to it. Fixes: 886f6f8337dd ("i2c: octeon: Support I2C_M_RECV_LEN") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Robert Richter <rric@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-01-27i2c: bpmp-tegra: Ignore unknown I2C_M flagsMikko Perttunen1-1/+1
commit bc1c2048abbe3c3074b4de91d213595c57741a6b upstream. In order to not to start returning errors when new I2C_M flags are added, change behavior to just ignore all flags that we don't know about. This includes the I2C_M_DMA_SAFE flag that already exists but causes -EINVAL to be returned for valid transactions. Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-17i2c: sprd: use a specific timeout to avoid system hang up issueChunyan Zhang1-1/+7
commit 0b884fe71f9ee6a5df35e677154256ea2099ebb8 upstream. If the i2c device SCL bus being pulled up due to some exception before message transfer done, the system cannot receive the completing interrupt signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT jiffies eclipse, that would make the system seemed hang up. To avoid that happen, this patch adds a specific timeout for message transfer. Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver") Signed-off-by: Linhua Xu <linhua.xu@unisoc.com> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> [wsa: changed errno to ETIMEDOUT] Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-11i2c: qup: Fix error return code in qup_i2c_bam_schedule_desc()Zhihao Cheng1-1/+2
commit e9acf0298c664f825e6f1158f2a97341bf9e03ca upstream. Fix to return the error code from qup_i2c_change_state() instaed of 0 in qup_i2c_bam_schedule_desc(). Fixes: fbf9921f8b35d9b2 ("i2c: qup: Fix error handling") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-11i2c: imx: Check for I2SR_IAL after every byteChristian Eggers1-0/+10
commit 1de67a3dee7a279ebe4d892b359fe3696938ec15 upstream. Arbitration Lost (IAL) can happen after every single byte transfer. If arbitration is lost, the I2C hardware will autonomously switch from master mode to slave. If a transfer is not aborted in this state, consecutive transfers will not be executed by the hardware and will timeout. Signed-off-by: Christian Eggers <ceggers@arri.de> Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-11i2c: imx: Fix reset of I2SR_IAL flagChristian Eggers1-5/+15
commit 384a9565f70a876c2e78e58c5ca0bbf0547e4f6d upstream. According to the "VFxxx Controller Reference Manual" (and the comment block starting at line 97), Vybrid requires writing a one for clearing an interrupt flag. Syncing the method for clearing I2SR_IIF in i2c_imx_isr(). Signed-off-by: Christian Eggers <ceggers@arri.de> Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-11i2c: imx: Don't generate STOP condition if arbitration has been lostChristian Eggers1-2/+10
commit 61e6fe59ede155881a622f5901551b1cc8748f6a upstream. If arbitration is lost, the master automatically changes to slave mode. I2SR_IBB may or may not be reset by hardware. Raising a STOP condition by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB. So calling i2c_imx_bus_busy() is not required and would busy-wait until timeout. Signed-off-by: Christian Eggers <ceggers@arri.de> Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove # the 3rd argument from the calls to # i2c_imx_bus_busy(). Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-05i2c: imx: Fix external abort on interrupt in exit pathsKrzysztof Kozlowski1-11/+13
commit e50e4f0b85be308a01b830c5fbdffc657e1a6dd0 upstream. If interrupt comes late, during probe error path or device remove (could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler i2c_imx_isr() will access registers with the clock being disabled. This leads to external abort on non-linefetch on Toradex Colibri VF50 module (with Vybrid VF5xx): Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003 Internal error: : 1008 [#1] ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607 Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) (i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0) (free_irq) from [<805844ec>] (release_nodes+0x178/0x284) (release_nodes) from [<80580030>] (really_probe+0x10c/0x348) (really_probe) from [<80580380>] (driver_probe_device+0x60/0x170) (driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60) (device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0) (__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4) (bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec) (bus_add_driver) from [<80581320>] (driver_register+0x78/0x110) (driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4) (do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc) (kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110) (kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20) Additionally, the i2c_imx_isr() could wake up the wait queue (imx_i2c_struct->queue) before its initialization happens. The resource-managed framework should not be used for interrupt handling, because the resource will be released too late - after disabling clocks. The interrupt handler is not prepared for such case. Fixes: 1c4b6c3bcf30 ("i2c: imx: implement bus recovery") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-30i2c: rcar: Auto select RESET_CONTROLLERDirk Behme1-0/+1
[ Upstream commit 5b9bacf28a973a6b16510493416baeefa2c06289 ] The i2c-rcar driver utilizes the Generic Reset Controller kernel feature, so select the RESET_CONTROLLER option when the I2C_RCAR option is selected with a Gen3 SoC. Fixes: 2b16fd63059ab9 ("i2c: rcar: handle RXDMA HW behaviour on Gen3") Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Andy Lowe <andy_lowe@mentor.com> [erosca: Add "if ARCH_RCAR_GEN3" per Wolfram's request] Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-14i2c: owl: Clear NACK and BUS error bitsCristian Ciocaltea1-0/+6
commit f5b3f433641c543ebe5171285a42aa6adcdb2d22 upstream. When the NACK and BUS error bits are set by the hardware, the driver is responsible for clearing them by writing "1" into the corresponding status registers. Hence perform the necessary operations in owl_i2c_interrupt(). Fixes: d211e62af466 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver") Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-14i2c: meson: fixup rate calculation with filter delayNicolas Belin1-11/+12
commit 1334d3b4e49e35d8912a7c37ffca4c5afb9a0516 upstream. Apparently, 15 cycles of the peripheral clock are used by the controller for sampling and filtering. Because this was not known before, the rate calculation is slightly off. Clean up and fix the calculation taking this filtering delay into account. Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller") Signed-off-by: Nicolas Belin <nbelin@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-14i2c: meson: fix clock setting overwriteJerome Brunet1-1/+18
commit 28683e847e2f20eed22cdd24f185d7783db396d3 upstream. When the slave address is written in do_start(), SLAVE_ADDR is written completely. This may overwrite some setting related to the clock rate or signal filtering. Fix this by writing only the bits related to slave address. To avoid causing unexpected changed, explicitly disable filtering or high/low clock mode which may have been left over by the bootloader. Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-14i2c: i801: Exclude device from suspend direct complete optimizationJean Delvare1-0/+1
commit 845b89127bc5458d0152a4d63f165c62a22fcb70 upstream. By default, PCI drivers with runtime PM enabled will skip the calls to suspend and resume on system PM. For this driver, we don't want that, as we need to perform additional steps for system PM to work properly on all systems. So instruct the PM core to not skip these calls. Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM") Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> [iwamatsu: Use DPM_FLAG_NEVER_SKIP instead of DPM_FLAG_NO_DIRECT_COMPLETE] Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-07i2c: cpm: Fix i2c_ram structureNicolas VINCENT1-0/+3
[ Upstream commit a2bd970aa62f2f7f80fd0d212b1d4ccea5df4aed ] the i2c_ram structure is missing the sdmatmp field mentionned in datasheet for MPC8272 at paragraph 36.5. With this field missing, the hardware would write past the allocated memory done through cpm_muram_alloc for the i2c_ram structure and land in memory allocated for the buffers descriptors corrupting the cbd_bufaddr field. Since this field is only set during setup(), the first i2c transaction would work and the following would send data read from an arbitrary memory location. Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers") Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-09-23i2c: i801: Fix resume bugVolker Rümelin1-7/+14
commit 66d402e2e9455cf0213c42b97f22a0493372d7cc upstream. On suspend the original host configuration gets restored. The resume routine has to undo this, otherwise the SMBus master may be left in disabled state or in i2c mode. [JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.] Signed-off-by: Volker Rümelin <vr_qemu@t-online.de> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03i2c: rcar: in slave mode, clear NACK earlierWolfram Sang1-0/+1
[ Upstream commit 914a7b3563b8fb92f976619bbd0fa3a4a708baae ] Currently, a NACK in slave mode is set/cleared when SCL is held low by the IP core right before the bit is about to be pushed out. This is too late for clearing and then a NACK from the previous byte is still used for the current one. Now, let's clear the NACK right after we detected the STOP condition following the NACK. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-08-21i2c: rcar: avoid race when unregistering slaveWolfram Sang1-3/+5
[ Upstream commit c7c9e914f9a0478fba4dc6f227cfd69cf84a4063 ] Due to the lockless design of the driver, it is theoretically possible to access a NULL pointer, if a slave interrupt was running while we were unregistering the slave. To make this rock solid, disable the interrupt for a short time while we are clearing the interrupt_enable register. This patch is purely based on code inspection. The OOPS is super-hard to trigger because clearing SAR (the address) makes interrupts even more unlikely to happen as well. While here, reinit SCR to SDBS because this bit should always be set according to documentation. There is no effect, though, because the interface is disabled. Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-08-21i2c: rcar: slave: only send STOP event when we have been addressedWolfram Sang1-3/+4
[ Upstream commit 314139f9f0abdba61ed9a8463bbcb0bf900ac5a2 ] When the SSR interrupt is activated, it will detect every STOP condition on the bus, not only the ones after we have been addressed. So, enable this interrupt only after we have been addressed, and disable it otherwise. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-08-05Revert "i2c: cadence: Fix the hold bit setting"Raviteja Narayanam1-7/+2
[ Upstream commit 0db9254d6b896b587759e2c844c277fb1a6da5b9 ] This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9. There are two issues with "i2c: cadence: Fix the hold bit setting" commit. 1. In case of combined message request from user space, when the HOLD bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent on the bus even before the last message is started. This is because when the HOLD bit is cleared, the FIFOS are empty and there is no pending transfer. The STOP condition should occur only after the last message is completed. 2. The code added by the commit is redundant. Driver is handling the setting/clearing of HOLD bit in right way before the commit. The setting of HOLD bit based on 'bus_hold_flag' is taken care in cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv functions. The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and cdns_i2c_recv functions based on bus_hold_flag and byte count. Since clearing of HOLD bit is done after the slave address is written to the register (writing to address register triggers the message transfer), it is ensured that STOP condition occurs at the right time after completion of the pending transfer (last message). Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-29i2c: rcar: always clear ICSAR to avoid side effectsWolfram Sang1-0/+3
[ Upstream commit eb01597158ffb1853a7a7fc2c57d4c844640f75e ] On R-Car Gen2, we get a timeout when reading from the address set in ICSAR, even though the slave interface is disabled. Clearing it fixes this situation. Note that Gen3 is not affected. To reproduce: bind and undbind an I2C slave on some bus, run 'i2cdetect' on that bus. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-22i2c: eg20t: Load module automatically if ID matchesAndy Shevchenko1-0/+1
[ Upstream commit 5f90786b31fb7d1e199a8999d46c4e3aea672e11 ] The driver can't be loaded automatically because it misses module alias to be provided. Add corresponding MODULE_DEVICE_TABLE() call to the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-09i2c: mlxcpld: check correct size of maximum RECV_LEN packetWolfram Sang1-2/+2
[ Upstream commit 597911287fcd13c3a4b4aa3e0a52b33d431e0a8e ] I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno to what is suggested for this error. Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Michael Shych <michaelsh@mellanox.com> Tested-by: Michael Shych <michaelsh@mellanox.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-01i2c: fsi: Fix the port number field in status registerEddie James1-1/+1
[ Upstream commit 502035e284cc7e9efef22b01771d822d49698ab9 ] The port number field in the status register was not correct, so fix it. Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm") Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-01i2c: tegra: Fix Maximum transfer sizeSowjanya Komatineni1-1/+14
[ Upstream commit b67d4530cdade7ebfafa2c6b46f2a0dad3e41bcb ] Tegra194 supports maximum 64K Bytes transfer per packet. Tegra186 and prior supports maximum 4K Bytes transfer per packet. This patch fixes this payload difference between Tegra194 and prior Tegra chipsets using separate i2c_adapter_quirks. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-01i2c: tegra: Add missing kerneldoc for some fieldsThierry Reding1-0/+15
[ Upstream commit 0604ee4aefa20f493a32dc223599f922fb615367 ] Not all fields were properly documented. Add kerneldoc for the missing fields to prevent the build from flagging them. Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-07-01i2c: tegra: Cleanup kerneldoc commentsThierry Reding1-12/+11
[ Upstream commit c990bbafdb11c608bba2d529f72ded9bdff88678 ] Some of the kerneldoc uses a strange spelling for abbreviations. Turn them into all-uppercase and clean up some whitespace issues while at it. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-25i2c: pxa: fix i2c_pxa_scream_blue_murder() debug outputRussell King1-4/+3
[ Upstream commit 88b73ee7ca4c90baf136ed5a8377fc5a9b73ac08 ] The IRQ log output is supposed to appear on a single line. However, commit 3a2dc1677b60 ("i2c: pxa: Update debug function to dump more info on error") resulted in it being printed one-entry-per-line, which is excessively long. Fixing this is not a trivial matter; using pr_cont() doesn't work as the previous dev_dbg() may not have been compiled in, or may be dynamic. Since the rest of this function output is at error level, and is also debug output, promote this to error level as well to avoid this problem. Reduce the number of always zero prefix digits to save screen real- estate. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-25i2c: pxa: clear all master action bits in i2c_pxa_stop_message()Russell King1-4/+2
[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ] If we timeout during a message transfer, the control register may contain bits that cause an action to be set. Read-modify-writing the register leaving these bits set may trigger the hardware to attempt one of these actions unintentionally. Always clear these bits when cleaning up after a message or after a timeout. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-06-25i2c: piix4: Detect secondary SMBus controller on AMD AM4 chipsetsAdam Honse1-1/+2
[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ] The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper equivalents have a secondary SMBus controller at I/O port address 0x0B20. This bus is used by several manufacturers to control motherboard RGB lighting via embedded controllers. I have been using this bus in my OpenRGB project to control the Aura RGB on many motherboards and ASRock also uses this bus for their Polychrome RGB controller. I am not aware of any CZ-compatible platforms which do not have the second SMBus channel. All of AMD's AM4- and Threadripper- series chipsets that OpenRGB users have tested appear to have this secondary bus. I also noticed this secondary bus is present on older AMD platforms including my FM1 home server. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587 Signed-off-by: Adam Honse <calcprogrammer1@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-03-01 23:20:06 +0300