| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
nct7904_data struct.
SMI# interrupt for fan and voltage is Two-Times Interrupt Mode.
Fan or voltage exceeds high limit or going below low limit,
it will causes an interrupt if the previous interrupt has been
reset by reading all the interrupt Status Register. Thus, add the
array fan_alarm and vsen_alarm to store the alarms for all of the
fan and voltage sensors.
Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190919030205.11440-1-Amy.Shih@advantech.com.tw
Fixes: 486842db3b79 ("hwmon: (nct7904) Add extra sysfs support for fan, voltage and temperature.")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Voltage sensors overlap with external temperature sensors. Detect
the multi-function of voltage, thermal diode and thermistor from
register VT_ADC_MD_REG to set value of vsen_mask in nct7904_data
struct.
Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190918084801.9859-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much
discussion and review and a day-long in-person meeting, they were
decided to be reverted and a new set of patches is currently being
reviewed on the mailing list.
Other than that churn, there are two "persistent" branches in here
that other trees will be pulling in as well during the merge window.
One branch to add support for drivers to have the driver core
automatically add sysfs attribute files when a driver is bound to a
device so that the driver doesn't have to manually do it (and then
clean it up, as it always gets it wrong).
There's another branch in here for generic lookup helpers for the
driver core that lots of busses are starting to use. That's the
majority of the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to
hopefully get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues"
[ Note that the above-mentioned generic lookup helpers branch was
already brought in by the LED merge (commit 4feaab05dc1e) that had
shared it.
Also note that that common branch introduced an i2c bug due to a bad
conversion, which got fixed here. - Linus ]
* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
coccinelle: platform_get_irq: Fix parse error
driver-core: add include guard to linux/container.h
sysfs: add BIN_ATTR_WO() macro
driver core: platform: Export platform_get_irq_optional()
hwmon: pwm-fan: Use platform_get_irq_optional()
driver core: platform: Introduce platform_get_irq_optional()
Revert "driver core: Add support for linking devices during device addition"
Revert "driver core: Add edit_links() callback for drivers"
Revert "of/platform: Add functional dependency link from DT bindings"
Revert "driver core: Add sync_state driver/bus callback"
Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
Revert "of/platform: Create device links for all child-supplier depencencies"
Revert "of/platform: Don't create device links for default busses"
Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
Revert "of/platform: Disable generic device linking code for PowerPC"
devcoredump: fix typo in comment
devcoredump: use memory_read_from_buffer
of/platform: Disable generic device linking code for PowerPC
device.h: Fix warnings for mismatched parameter names in comments
...
|
|
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc:lock: remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
|
|
temperature and fan.
According to datasheet, the SMI status register setting of LTD
temperature is SMI_STS3, and the SMI status register setting
of fan is SMI_STS5 and SMI_STS6.
Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190912113300.4714-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the Sensirion SHTC3 humidity and temperature sensor to
the shtc1 module.
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-2-dan@dlrobertson.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.
Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Current sample time values are over estimated, this patches applies
values closer to the ones defined in the data-sheets.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
[groeck: resolved conflicts; use default conversion times]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
And simplify the error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-4-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
And simplify the error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-3-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
And simplify the error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190903181256.13450-2-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci
Fixes: 658e687b4218 ("hwmon: Add Synaptics AS370 PVT sensor driver")
CC: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909030646180.3228@hadrien
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
For PCT7027, the sampling period is configured using a dedicated
register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TMP112 uses an uncommon method to write the conversion time: its
configuration register is 16 bit wide, and the conversion time is
configured in its second byte.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We'll need per-chip handling for updating the sample interval.
To prepare for it, separate the code implementing it into its own
function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The conversion (sample) time is configurable for several chips supported
by the lm75 driver. With the necessary infrastructure in place, enable
this support for all chips using the configuration register for this
purpose.
DS1775:
Conversion time: 187.5, 375, 750, 1500 ms
Sensor resolution: 9, 10, 11, 12 bit
DS75, STDS75:
Conversion time: 150, 300, 600, 1200 ms
Sensor resolution: 9, 10, 11, 12 bit
DS7505:
Conversion time: 25, 50, 100, 200 ms
Sensor resolution: 9, 10, 11, 12 bit
MCP980[0123]:
Conversion time: 75, 150, 300, 600 ms
Sensor resolution: 9, 10, 11, 12 bit
TMP100, TMP101:
Conversion time: 75, 150, 300, 600 ms
Sensor resolution: 9, 10, 11, 12 bit
TMP75, TMP105, TMP175, TMP275:
Conversion time: 38, 75, 150, 300 ms
Sensor resolution: 9, 10, 11, 12 bit
While doing this, it became obvious that the masks and values to set
the converion (sample) time is similar for all those chips, and that
other chips with configurable sample times will need separate code anyway.
For that reason, replace the sample_set_masks and sample_clr_mask
configuration parameters with a single array and with a constant.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
According to kernel hwmon sysfs-interface documentation, temperature
critical max value, typically greater than corresponding temp_max values.
Thus, reads the LTD_HV_HL (LTD HIGH VALUE HIGH LIMITATION) and LTD_LV_HL
(LTD LOW VALUE HIGH LIMITATION) for case hwmon_temp_crit and
hwmon_temp_crit_hyst. Reads the LTD_HV_LL (HIGH VALUE LOW LIMITATION)
and LTD_LV_LL (LOW VALUE LOW LIMITATION) for case hwmon_temp_max
and hwmon_temp_max_hyst.
Signed-off-by: amy.shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20850618155720.24857-1-Amy.Shih@advantech.com.tw
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a new driver for Synaptics AS370 PVT sensors. Currently, only
temperature is supported.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190827113259.4fb64a17@xhacker.debian
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Version 2 of the PSU supports a second page of data and changes the
format of the FW version. Use the devicetree binding to differentiate
between the version the driver should use.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1567192263-15065-4-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There is no reason why power channel shouldn't be exported as is done for
voltage, current, temperature and humidity.
Power channel is available on iio ina226 driver.
Sysfs IIO documentation for power attribute added by commit 7c6d5c7ee883
("iio: Documentation: Add missing documentation for power attribute")
is declaring that value is in mili-Watts but hwmon interface is expecting
value in micro-Watts that's why there is a need for mili-Watts to
micro-Watts conversion.
Tested on Xilinx ZCU102 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/db71f5ae87e4521a2856a1be5544de0b6cede575.1566483741.git.michal.simek@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.
This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ltc2990 will now use device_property_read_u32_array() instead of
of_property_read_u32_array() - allowing the use of software nodes
via fwnode_create_software_node().
This allows code using i2c_new_device() to specify a default
measurement mode for the LTC2990 via fwnode_create_software_node().
Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20190819121618.16557-2-max@enpas.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The email address listed in MODULE_AUTHOR() will be disabled in the
near future. Replace it with my private one.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1565720249-6549-2-git-send-email-wahrenst@gmx.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
* Create two separate functions to write into hwmon_temp and hwmon_chip.
* Call the functions from lm75_write.
* Make hwm_chip writable if the chip supports more than one sample time.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-5-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The new fields are included to prepare the driver for next patch. The
fields are:
* *resolutions: Stores all the supported resolutions by the device.
* num_sample_times: Stores the number of possible sample times.
* *sample_times: Stores all the possible sample times to be set.
* sample_set_masks: The set_masks for the possible sample times
* sample_clr_mask: Clear mask to set the default sample time.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-4-iker.perez@codethink.co.uk
[groeck: Minor structure documentation fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Wrap the existing code to write configurations into registers in
a function.
Added error handling to the function.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-3-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
* Add to lm75_data kind field to store the kind of device the driver is
working with.
* Add an structure to store the configuration parameters of all the
supported devices.
* Delete resolution_limits from lm75_data and include them in the structure
described above.
* Add a pointer to the configuration parameters structure to be used as a
reference to obtain the parameters.
* Delete switch-case approach to get the device configuration parameters.
* The structure is cleaner and easier to maintain.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-2-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
NCT-7904D also supports reading of channel limitation registers as well
as SMI status registers for fan, voltage and temperature monitoring.
It also supports reading the temperature sensor type (thermal diode,
thermistor, AMD SB-TSI or Intel PECI).
Add the following sysfs nodes:
-fan[1-*]_min
-fan[1-*]_alarm
-in[1-*]_min
-in[1-*]_max
-in[1-*]_alarm
-temp[1-*]_max
-temp[1-*]_max_hyst
-temp[1-*]_emergency
-temp[1-*]_emergency_hyst
-temp[1-*]_alarm
-temp[1-*]_type
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190807013842.24451-1-Amy.Shih@advantech.com.tw
[groeck: Clarified description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
I have been using SENSORS_W83795_FANCTRL for several years and never
had any problem. When the driver was added, I had not tested that
part of the driver yet so I wanted to be super cautious, but time has
shown that it works just fine.
In the long run I even believe that we should drop the option and
enable the feature unconditionally. It doesn't do anything until the
user explicitly starts twiddling with sysfs attributes anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20190806102123.3118bcc5@endymion
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[groeck: Dropped jz4740-hwmon.c (driver is being removed)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.
While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.
The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.
Signed-off-by: Wang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for NCT6116D to nct6775 driver.
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
hwmon_device_register() is a deprecated function and produces a warning.
Converting the driver to use the hwmon_device_register_with_groups()
instead.
Signed-off-by: Grant McEwan <grant.mcewan@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20190721225530.28799-2-grant.mcewan@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-4-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-3-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20190722172611.3797-2-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
It would seem like model 70h is behaving in the same way as model 30h,
so let's just add the new F3 PCI ID to the list of compatible devices.
Unlike previous Ryzen/Threadripper, Ryzen gen 3 processors do not need
temperature offsets anymore. This has been reported in the press and
verified on my Ryzen 3700X by checking that the idle temperature
reported by k10temp is matching the temperature reported by the
firmware.
Vicki Pfau sent an identical patch after I checked that no-one had
written this patch. I would have been happy about dropping my patch but
unlike for his patch series, I had already Cc:ed the x86 people and
they already reviewed the changes. Since Vicki has not answered to
any email after his initial series, let's assume she is on vacation
and let's avoid duplication of reviews from the maintainers and merge
my series. To acknowledge Vicki's anteriority, I added her S-o-b to
the patch.
v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Tested-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: "Woods, Brian" <Brian.Woods@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20190722174653.2391-1-marcel.p.bocu@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Removes:
- hwmon_dev from k8temp_data struct, as that is now passed
to callbacks, anyway.
- other k8temp_data struct fields, too.
- k8temp_update_device()
Also reduces binary size:
text data bss dec hex filename
4139 1448 0 5587 15d3 drivers/hwmon/k8temp.ko.bak
3103 1220 0 4323 10e3 drivers/hwmon/k8temp.ko
Signed-off-by: Robert Karszniewicz <avoidr@firemail.cc>
Signed-off-by: Robert Karszniewicz <avoidr@riseup.net>
Link: https://lore.kernel.org/r/20190721120051.28064-1-avoidr@riseup.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There is a typo in MAX37185_NUM_FAN_PAGES. To be consistent, it should be
MAX31785_NUM_FAN_PAGES (1 and 7 switched).
At line 24, we already have:
#define MAX31785_NR_FAN_PAGES 6
and MAX37185_NUM_FAN_PAGES seems to be unused.
It is likely that it is only a typo and/or a left-over.
So, axe it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190721101553.20911-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The NXP PCT2075 is largely compatible with other chips already supported
by the LM75 driver. It uses an 11-bit resolution and defaults to 100 ms
sampling period. The datasheet is here:
https://www.nxp.com/docs/en/data-sheet/PCT2075.pdf
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20190711124504.7580-2-daniel@zonque.org
[groeck: Documentation update]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In coretemp_init(), 'zone_devices' is allocated through kcalloc().
However, it is not deallocated in the following execution if
platform_driver_register() fails, leading to a memory leak. To fix this
issue, introduce the 'outzone' label to free 'zone_devices' before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Link: https://lore.kernel.org/r/1566248402-6538-1-git-send-email-wenwen@cs.uga.edu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Writes into limit registers fail if the temperature written is negative.
The regmap write operation checks the value range, regmap_write accepts
an unsigned int as parameter, and the temperature value passed to
regmap_write is kept in a variable declared as long. Negative values
are converted large unsigned integers, which fails the range check.
Fix by type casting the temperature to u16 when calling regmap_write().
Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Fixes: e65365fed87f ("hwmon: (lm75) Convert to use regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Build bot reports the following build issue after commit 9091373ab7ea
("gpio: remove less important #ifdef around declarations):
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:576:1: error: redefinition of 'gpiochip_add_pin_range'
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:245:1: note: previous definition of 'gpiochip_add_pin_range' was here
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:583:1: error: redefinition of 'gpiochip_add_pingroup_range'
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:254:1: note: previous definition of 'gpiochip_add_pingroup_range' was here
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:591:1: error: redefinition of 'gpiochip_remove_pin_ranges'
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:263:1: note: previous definition of 'gpiochip_remove_pin_ranges' was here
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
This is caused by conflicting defines from linux/gpio.h and
linux/gpio/driver.h. Drivers should not include both the legacy and
the new API headers. This driver doesn't even use linux/gpio.h so
remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190808080144.6183-1-brgl@bgdev.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The PWM fan interrupt is optional, so we don't want an error message in
the kernel log if it wasn't specified.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://lore.kernel.org/r/20190828083411.2496-2-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.
In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The configuration register of the tmp75b sensor is 16bit long, however
the first byte is reserved, so there is not no need to take care of it.
Because the order of the bytes is little endian and it is only necessary
to write one byte, the desired bits must be shifted into a 8 bit range.
Fixes: 39abe9d88b30 ("hwmon: (lm75) Add support for TMP75B")
Cc: stable@vger.kernel.org
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190801075324.4638-1-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.
In detail:
- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.
Fix is_visible function to detect and report in4_input visibility
as expected.
Reported-by: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: stable@vger.kernel.org
Fixes: 3434f37835804 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
