| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 75fe87e19d8aff81eb2c64d15d244ab8da4de945 ]
appleir_remove() runs hid_hw_stop() before timer_delete_sync().
hid_hw_stop() synchronously unregisters the HID input device via
hid_disconnect() -> hidinput_disconnect() -> input_unregister_device(),
which drops the last reference and frees the underlying input_dev when
no userspace handle holds it open.
key_up_tick() reads appleir->input_dev and calls input_report_key() /
input_sync() on it. The timer is armed from appleir_raw_event() with
a HZ/8 (~125 ms) timeout on every keydown and key-repeat report. If a
key was pressed shortly before the device is disconnected, the timer
can fire after hid_hw_stop() has freed input_dev but before the
teardown drains it.
A simple reorder is not sufficient. Putting the timer drain first
still leaves a window where a USB URB completion (raw_event) running
during hid_hw_stop() can call mod_timer() and re-arm the timer, which
then fires after hidinput_disconnect() has freed input_dev. The same
URB-completion window also lets raw_event() reach key_up(), key_down()
and battery_flat() directly, all of which dereference
appleir->input_dev.
Introduce a 'removing' flag on struct appleir, gated by the existing
spinlock. appleir_remove() sets the flag under the lock and then
shuts down the timer with timer_shutdown_sync(), which both drains any
in-flight callback and permanently disables further mod_timer() calls.
appleir_raw_event() and key_up_tick() bail out early if the flag is
set, so no path can arm or run the timer, or dereference
appleir->input_dev, after remove() has started tearing down.
The keyrepeat and flatbattery branches of appleir_raw_event()
previously called into the input layer without holding the spinlock;
take it now so the flag check is well-defined. This incidentally
closes a pre-existing read-side race on appleir->current_key in the
keyrepeat branch.
This bug is structurally a sibling of commit 4db2af929279 ("HID:
appletb-kbd: fix UAF in inactivity-timer cleanup path") and has been
present since the driver was introduced.
Fixes: 9a4a5574ce42 ("HID: appleir: add support for Apple ir devices")
Cc: stable@vger.kernel.org
Signed-off-by: Manish Khadka <maskmemanish@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8813b0612275cc61fe9e6603d0ee019247ade6be ]
mt_io_flags is a single unsigned long, but mt_process_slot(),
mt_release_pending_palms() and mt_release_contacts() use it as a
per-slot bitmap indexed by the slot number. That slot number is only
bounded by td->maxcontacts, which is taken from the device's
ContactCountMaximum feature report and can be up to 255, not by
BITS_PER_LONG.
As a result, a multitouch device that advertises a large contact count
makes set_bit()/clear_bit() operate past the mt_io_flags word and
corrupt the adjacent members of struct mt_device. The sticky-fingers
release timer is the easiest way to reach this. mt_release_contacts()
runs
for (i = 0; i < mt->num_slots; i++)
clear_bit(i, &td->mt_io_flags);
with num_slots == maxcontacts. For maxcontacts around 250 the loop
clears the bits that overlap td->applications.next, zeroing that list
head, and the list_for_each_entry() that immediately follows then
dereferences NULL. The kernel panics from timer (softirq) context. On a
KASAN build this shows up as a general protection fault in
mt_release_contacts() with a null-ptr-deref at offset 0x58, which is
offsetof(struct mt_application, num_received).
The state is reachable from an untrusted USB or Bluetooth HID
multitouch device; no local privileges are required.
Store the per-slot active state in a separately allocated bitmap sized
for maxcontacts, the same pattern already used for pending_palm_slots,
and keep only MT_IO_FLAGS_RUNNING in mt_io_flags. The two
"mt_io_flags & MT_IO_SLOTS_MASK" arming checks become
bitmap_empty(td->active_slots, td->maxcontacts).
Move MT_IO_FLAGS_RUNNING back to bit 0. It was bumped to bit 32 by the
same commit to leave the low byte for the slot bits; with the slot bits
gone it fits in bit 0 again, which also keeps it within the unsigned
long on 32-bit.
Fixes: 46f781e0d151 ("HID: multitouch: fix sticky fingers")
Cc: stable@vger.kernel.org
Signed-off-by: Trung Nguyen <trungnh@cystack.net>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit af1a9b65ebe8a948eda805c14b78d4d0767cb1b5 ]
When a caller passes a size of 0 to hid_report_raw_event() for a
numbered report, the function originally called hid_get_report() before
performing any size validation.
Inside hid_get_report(), if the report is numbered (report_enum->numbered
is true), it unconditionally dereferences data[0] to extract the report ID.
With a size of 0, this results in an out-of-bounds read or kernel panic.
Fix this by moving the numbered report size validation check before the
call to hid_get_report(), ensuring that size is at least 1 before
dereferencing the data pointer.
Fixes: 2c85c61d1332 ("HID: pass the buffer size to hid_report_raw_event")
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0021eb09041f021c079be1022934a280f7f176c0 ]
In picolcd_send_and_wait(), an integer overflow of the signed loop counter
'k' can theoretically lead to a NULL pointer dereference of 'raw_data'.
If the loop executes more than INT_MAX times, 'k' becomes negative,
making the condition 'k < size' true even when 'size' is 0.
Change the type of 'k' to 'unsigned int' to prevent the overflow and
eliminate the out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
[jkosina@suse.com: extended hash length]
Fixes: fabdbf2fd22fa17 ("HID: picoLCD: split driver code")
Signed-off-by: Georgiy Osokin <g.osokin@auroraos.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f22a5db8a7d38152556f230d6d68e59dbc27971b ]
The @dev member described in the kernel-doc does not exist in the
struct. Remove the stale entry.
Fixes: 0610430e3dea ("HID: logitech-hidpp: add input_device ptr to struct hidpp_device")
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f784fcea450617055d2d12eec5b2f6e0e38bf878 upstream.
sensor_hub_input_attr_get_raw_value() is limited to returning a single
32-bit value, which is insufficient for sensors that report data larger
than 32 bits, such as a quaternion with four s16 elements.
Add sensor_hub_input_attr_read_values() that accepts a caller-provided
buffer and accumulates incoming data until the buffer is full. The two
paths are distinguished in sensor_hub_raw_event() by pending.max_raw_size
being non-zero, preserving backward compatibility.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Co-developed-by: Zhang Lixu <lixu.zhang@intel.com>
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7705b4140d188ce22656f6e541ae7ef834c7e11a upstream.
lg_g15_data is allocated with devm and holds a work item. The report
handlers schedule that work straight from device input.
lg_g15_event() and lg_g15_v2_event() do it on the backlight cycle key,
and lg_g510_leds_event() does it too. The worker dereferences the
lg_g15_data back through container_of.
The driver had no remove callback and never cancelled the work. So if a
report scheduled the work and the keyboard was then unplugged, devres
freed lg_g15_data while the work was still pending or running, and the
worker touched freed memory. This is a use-after-free. It is reachable
as a race on device unplug.
Add a remove callback that cancels the work before devres frees the
state. g15->work is only initialized for the models that schedule it
(G15, G15 v2, G510). The G13 and Z-10 leave it zeroed, so guard the
cancel on g15->work.func to avoid cancelling a work that was never set
up. The g15 NULL test mirrors the one already in lg_g15_raw_event().
Fixes: 97b741aba918 ("HID: lg-g15: Add keyboard and LCD backlight control")
Cc: stable@vger.kernel.org
Suggested-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec2612b8ad9e642596db011dd8b6568ef1edeaa1 upstream.
wacom_parse_and_register() starts HID hardware before registering inputs
and initializing pad LEDs/remotes. Those later steps can fail, but their
error paths currently release Wacom resources without stopping the HID
hardware.
Route post-hid_hw_start() failures through hid_hw_stop() before
releasing driver resources.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: c1d6708bf0d3 ("HID: wacom: Do not register input devices until after hid_hw_start")
Cc: stable@vger.kernel.org
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d3a2a466b8d68d852a1f3bbf11204b718428dc4 ]
When building for 32-bit platforms, for which 'size_t' is
'unsigned int', there are warnings around using the incorrect format
specifier to print bsize in hid_report_raw_event():
drivers/hid/hid-core.c:2054:29: error: format specifies type 'long' but the argument has type 'size_t' (aka 'unsigned int') [-Werror,-Wformat]
2053 | hid_warn_ratelimited(hid, "Event data for report %d is incorrect (%d vs %ld)\n",
| ~~~
| %zu
2054 | report->id, csize, bsize);
| ^~~~~
drivers/hid/hid-core.c:2076:29: error: format specifies type 'long' but the argument has type 'size_t' (aka 'unsigned int') [-Werror,-Wformat]
2075 | hid_warn_ratelimited(hid, "Event data for report %d was too short (%d vs %ld)\n",
| ~~~
| %zu
2076 | report->id, rsize, bsize);
| ^~~~~
Use the proper 'size_t' format specifier, '%zu', to clear up the
warnings.
Cc: stable@vger.kernel.org
Fixes: 2c85c61d1332 ("HID: pass the buffer size to hid_report_raw_event")
Reported-by: Miguel Ojeda <ojeda@kernel.org>
Closes: https://lore.kernel.org/20260516020430.110135-1-ojeda@kernel.org/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 3ab135238832446399614e7a4bb796d620717806)
Signed-off-by: Lee Jones <lee@kernel.org>
(cherry picked from commit 0f77a993b5426cca1b046c9ab4b2f8355a4d45dc)
Signed-off-by: Lee Jones <lee@kernel.org>
(cherry picked from commit 70333a8f866aad8cbd6956e2ec4ace159fa4243b)
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c85c61d1332e1e16f020d76951baf167dcb6f7a ]
commit 0a3fe972a7cb ("HID: core: Mitigate potential OOB by removing
bogus memset()") enforced the provided data to be at least the size of
the declared buffer in the report descriptor to prevent a buffer
overflow. However, we can try to be smarter by providing both the buffer
size and the data size, meaning that hid_report_raw_event() can make
better decision whether we should plaining reject the buffer (buffer
overflow attempt) or if we can safely memset it to 0 and pass it to the
rest of the stack.
Fixes: 0a3fe972a7cb ("HID: core: Mitigate potential OOB by removing bogus memset()")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Stable-dep-of: 206342541fc8 ("HID: core: introduce hid_safe_input_report()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 509c2605065004fc4cd86ee50a9350d402785307)
[Lee: Backported to linux-6.12.y and beyond]
Signed-off-by: Lee Jones <lee@kernel.org>
(cherry picked from commit f9393998660f146970047bda31526aeb96190f28)
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c0a8899e02ddebd51e2589835182c239c2e224ae upstream.
wacom_hid_set_device_mode() currently assumes that the HID_DG_INPUTMODE
usage is always located in the first field (field[0]) of the feature report.
However, a device can specify HID_DG_INPUTMODE in a different field.
If HID_DG_INPUTMODE is in a field other than the first one and the first
field has a report_count smaller than the usage_index of HID_DG_INPUTMODE,
this leads to an out-of-bounds write to r->field[0]->value.
Fix this by storing the field index of HID_DG_INPUTMODE in 'struct
hid_data' during feature mapping. In wacom_hid_set_device_mode(), use
this stored field index to access the correct field and add bounds
checks to ensure both the field index and the value index are within
valid ranges before writing.
Cc: stable@vger.kernel.org
Fixes: 5ae6e89f7409 ("HID: wacom: implement the finger part of the HID generic handling")
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f90dcfa8dc32a488581b78e575cdd7808ba5c78 ]
Commit c7fabe4ad921 ("HID: quirks: work around VID/PID conflict for
appledisplay") intends to add a quirk for kernels built with Apple Cinema
Display support, but it refers to the non-existing config option
CONFIG_APPLEDISPLAY, whereas the config option for Apple Cinema Display
support is named CONFIG_USB_APPLEDISPLAY.
Refer to the intended config option CONFIG_USB_APPLEDISPLAY in the ifdef
directive.
Fixes: c7fabe4ad921 ("HID: quirks: work around VID/PID conflict for appledisplay")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8df2c1b47ee3cd50fd454f75c7a7e2ae8a6adf72 ]
You can build a USB device that includes a HID component
and a storage or UAS component. The components can be reset
only together. That means that hid_pre_reset() and hid_post_reset()
are in the block IO error handling. Hence no memory allocation
used in them may do block IO because the IO can deadlock
on the mutex held while resetting a device and calling the
interface drivers.
Use GFP_NOIO for all allocations in them.
Fixes: dc3c78e434690 ("HID: usbhid: Check HID report descriptor contents after device reset")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7253091766ded0fd81fe8d8be9b8b835495b06e8 ]
In order to avoid dereferencing a NULL pointer asus_probe is aborted early
and control of some asus devices is transferred over hid-generic after
erroring out even when such NULL dereference cannot happen: only early
abort when the NULL dereference can happen.
Also make the code shorter and more adherent to coding standards
removing square brackets enclosing single-line if-else statements.
Fixes: d3af6ca9a8c3 ("HID: asus: fix UAF via HID_CLAIMED_INPUT validation")
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 51d33b42b8ae23da92819d28439fdd5636c45186 ]
Linux kernel coding standars requires functions opening brackets to be in
a newline: move the opening bracket of asus_resume in its own line.
Fixes: 546edbd26cff ("HID: hid-asus: reset the backlight brightness level on resume")
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 69c02ffde6ed4d535fa4e693a9e572729cad3d0d upstream.
s32ton() shifts by n-1 where n is the field's report_size, a value that
comes directly from a HID device. The HID parser bounds report_size
only to <= 256, so a broken HID device can supply a report descriptor
with a wide field that triggers shift exponents up to 256 on a 32-bit
type when an output report is built via hid_output_field() or
hid_set_field().
Commit ec61b41918587 ("HID: core: fix shift-out-of-bounds in
hid_report_raw_event") added the same n > 32 clamp to the function
snto32(), but s32ton() was never given the same fix as I guess syzbot
hadn't figured out how to fuzz a device the same way.
Fix this up by just clamping the max value of n, just like snto32()
does.
Cc: stable <stable@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <bentiss@kernel.org>
Cc: linux-input@vger.kernel.org
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1badfc4319224820d5d890f8eab6aa52e4e83339 upstream.
Commit ecfa6f34492c ("HID: Add HID_CLAIMED_INPUT guards in raw_event
callbacks missing them") attempted to fix up the HID drivers that had
missed the previous fix that was done in 2ff5baa9b527 ("HID: appleir:
Fix potential NULL dereference at raw event handle"), but the alps
driver was missed.
Fix this up by properly checking in the hid-alps driver that it had been
claimed correctly before attempting to process the raw event.
Fixes: 73196ebe134d ("HID: alps: add support for Alps T4 Touchpad device")
Cc: stable <stable@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <bentiss@kernel.org>
Cc: Masaki Ota <masaki.ota@jp.alps.com>
Cc: linux-input@vger.kernel.org
Assisted-by: gregkh_clanker_t1000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d802d848308b35220f21a8025352f0c0aba15c12 ]
roccat_report_event() iterates over the device->readers list without
holding the readers_lock. This allows a concurrent roccat_release() to
remove and free a reader while it's still being accessed, leading to a
use-after-free.
Protect the readers list traversal with the readers_lock mutex.
Signed-off-by: Benoît Sevens <bsevens@google.com>
Reviewed-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 532743944324a873bbaf8620fcabcd0e69e30c36 ]
According to a mailing list report [1], this controller's predecessor
has the same issue. However, it uses the xpad driver instead of HID, so
this quirk wouldn't apply.
[1]: https://lore.kernel.org/linux-input/unufo3$det$1@ciao.gmane.io/
Signed-off-by: leo vriska <leo@60228.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e716edafedad4952fe3a4a273d2e039a84e8681a ]
It is possible for a malicious (or clumsy) device to respond to a
specific report's feature request using a completely different report
ID. This can cause confusion in the HID core resulting in nasty
side-effects such as OOB writes.
Add a check to ensure that the report ID in the response, matches the
one that was requested. If it doesn't, omit reporting the raw event and
return early.
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f1763f62909ccb6386ac50350fa0abbf5bb16a9 ]
The wacom_intuos_bt_irq() function processes Bluetooth HID reports
without sufficient bounds checking. A maliciously crafted short report
can trigger an out-of-bounds read when copying data into the wacom
structure.
Specifically, report 0x03 requires at least 22 bytes to safely read
the processed data and battery status, while report 0x04 (which
falls through to 0x03) requires 32 bytes.
Add explicit length checks for these report IDs and log a warning if
a short report is received.
Signed-off-by: Benoît Sevens <bsevens@google.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e31b556c0ba21f20c298aa61181b96541140b7b9 ]
When an I2C SMBus read operation fails, the MCP2221 internal state machine
may not reset correctly, causing subsequent transactions to fail.
By adding a short delay and explicitly cancelling the last command,
we ensure the device is ready for the next operation.
Fix an issue where i2cdetect was not able to detect all devices correctly
on the bus.
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2bad24c17742fc88973d6aea526ce1353f5334a3 ]
The asus_report_fixup() function was returning a newly allocated
kmemdup()-allocated buffer, but never freeing it. Switch to
devm_kzalloc() to ensure the memory is managed and freed automatically
when the device is removed.
The caller of report_fixup() does not take ownership of the returned
pointer, but it is permitted to return a pointer whose lifetime is at
least that of the input buffer.
Also fix a harmless out-of-bounds read by copying only the original
descriptor size.
Assisted-by: Gemini-CLI:Google Gemini 3
Signed-off-by: Günther Noack <gnoack@google.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ecfa6f34492c493a9a1dc2900f3edeb01c79946b upstream.
In commit 2ff5baa9b527 ("HID: appleir: Fix potential NULL dereference at
raw event handle"), we handle the fact that raw event callbacks
can happen even for a HID device that has not been "claimed" causing a
crash if a broken device were attempted to be connected to the system.
Fix up the remaining in-tree HID drivers that forgot to add this same
check to resolve the same issue.
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <bentiss@kernel.org>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: linux-input@vger.kernel.org
Cc: stable <stable@kernel.org>
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1547d41f9f19d691c2c9ce4c29f746297baef9e9 ]
Do not crash when a report has no fields.
Fake USB gadgets can send their own HID report descriptors and can define report
structures without valid fields. This can be used to crash the kernel over USB.
Cc: stable@vger.kernel.org
Signed-off-by: Günther Noack <gnoack@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cee8337e1bad168136aecfe6416ecd7d3aa7529a ]
Fake USB devices can send their own report descriptors for which the
input_mapping() hook does not get called. In this case, pm->input_ep82 stays
NULL, which leads to a crash later.
This does not happen with the real device, but can be provoked by imposing as
one.
Cc: stable@vger.kernel.org
Signed-off-by: Günther Noack <gnoack@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 17abd396548035fbd6179ee1a431bd75d49676a7 ]
Fake USB devices can send their own report descriptors for which the
input_mapping() hook does not get called. In this case, msc->input stays NULL,
leading to a crash at a later time.
Detect this condition in the input_configured() hook and reject the device.
This is not supposed to happen with actual magic mouse devices, but can be
provoked by imposing as a magic mouse USB device.
Cc: stable@vger.kernel.org
Signed-off-by: Günther Noack <gnoack@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3756a272d2cf356d2203da8474d173257f5f8521 ]
Errors in init must be reported back or we'll
follow a NULL pointer the first time FF is used.
Fixes: 20eb127906709 ("hid: force feedback driver for PantherLord USB/PS2 2in1 Adapter")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e4ac86b2ddd36fe501e20ecfcc080e536df1f48 ]
Add support for the for the EXC3188 touchscreen from eGalaxy.
Signed-off-by: Thorsten Schmelzer <tschmelzer@topcon.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85a866809333cd2bf8ddac93d9a3e3ba8e4f807d ]
The USB speaker has a bug that causes it to reboot when changing the
brightness using the physical knob.
Add a new vendor and product ID entry in hid-ids.h, and register
the corresponding device in hid-quirks.c with the required quirk.
Signed-off-by: Rodrigo Lugathe da Conceição Alves <lugathe2@gmail.com>
Reviewed-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c06bc3557542307b9658fbd43cc946a14250347b ]
Another Chicony Electronics HP 5MP Camera with USB ID 04F2:B882
reports a HID sensor interface that is not actually implemented.
Add the device to the HID ignore list so the bogus sensor is never
exposed to userspace. Then the system won't hang when runtime PM
tries to wake the unresponsive device.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56e230723e3a818373bd62331bccb1c6d2b3881b ]
Some systems have enabled ISH without any sensors. In this case sending
HOSTIF_DM_ENUM_DEVICES results in 0 sensors. This triggers ISH hardware
reset on subsequent enumeration after S3/S4 resume.
The enum_devices_done flag was not reset before sending the
HOSTIF_DM_ENUM_DEVICES command. On subsequent enumeration calls (such as
after S3/S4 resume), this flag retains its previous true value, causing the
wait loop to be skipped and returning prematurely to hid_ishtp_cl_init().
If 0 HID devices are found, hid_ishtp_cl_init() skips getting HID device
descriptors and sets init_done to true. When the delayed enumeration
response arrives with init_done already true, the driver treats it as a bad
packet and triggers an ISH hardware reset.
Set enum_devices_done to false before sending the enumeration command,
consistent with similar functions like ishtp_get_hid_descriptor() and
ishtp_get_report_descriptor() which reset their respective flags.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff3f234ff1dcd6d626a989151db067a1b7f0f215 ]
Some VTL-class touchpads (e.g. TOPS0102:00 35CC:0104) intermittently
fail to release a finger contact. A previous slot remains logically
active, accompanied by stale BTN_TOOL_DOUBLETAP state, causing
gestures to stay latched and resulting in stuck two-finger
scrolling and false right-clicks.
Apply MT_QUIRK_STICKY_FINGERS to handle the unreleased contact correctly.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/1225
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: DaytonCL <artem749507@gmail.com>
Signed-off-by: DaytonCL <artem749507@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd07f751208ba190f9b0db5e5b7f35d5bb4a8a1e ]
devm_kasprintf() returns NULL when memory allocation fails. Currently,
uclogic_input_configured() does not check for this case, which results
in a NULL pointer dereference.
Add NULL check after devm_kasprintf() to prevent this issue.
Fixes: dd613a4e45f8 ("HID: uclogic: Correct devm device reference for hidinput input_dev name")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
[ Adjust context ]
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dd613a4e45f8d35f49a63a2064e5308fa5619e29 ]
Reference the HID device rather than the input device for the devm
allocation of the input_dev name. Referencing the input_dev would lead to a
use-after-free when the input_dev was unregistered and subsequently fires a
uevent that depends on the name. At the point of firing the uevent, the
name would be freed by devres management.
Use devm_kasprintf to simplify the logic for allocating memory and
formatting the input_dev name string.
Reported-by: syzbot+3a0ebe8a52b89c63739d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-input/ZOZIZCND+L0P1wJc@penguin/T/
Reported-by: Maxime Ripard <mripard@kernel.org>
Closes: https://lore.kernel.org/linux-input/ZOZIZCND+L0P1wJc@penguin/T/#m443f3dce92520f74b6cf6ffa8653f9c92643d4ae
Fixes: cce2dbdf258e ("HID: uclogic: name the input nodes based on their tool")
Suggested-by: Maxime Ripard <mripard@kernel.org>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230824061308.222021-2-sergeantsagara@protonmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
[ Adjust context ]
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f28beb69c51517aec7067dfb2074e7c751542384 upstream.
Some faulty devices (ZWO EFWmini) have a wrong optional HID class
descriptor count compared to the provided length.
Given that we plainly ignore those optional descriptor, we can attempt
to fix the provided number so we do not lock out those devices.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c7fabe4ad9219866c203164a214c474c95b36bf2 ]
For years I wondered why the Apple Cinema Display driver would not
just work for me. Turns out the hidraw driver instantly takes it
over. Fix by adding appledisplay VID/PIDs to hid_have_special_driver.
Fixes: 069e8a65cd79 ("Driver for Apple Cinema Display")
Signed-off-by: René Rebe <rene@exactco.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a6b87bfc2ab5bccb7ad953693c85d9062aef3fdd ]
Testing by the syzbot fuzzer showed that the HID core gets a
shift-out-of-bounds exception when it tries to convert a 32-bit
quantity to a 0-bit quantity. Ideally this should never occur, but
there are buggy devices and some might have a report field with size
set to zero; we shouldn't reject the report or the device just because
of that.
Instead, harden the s32ton() routine so that it returns a reasonable
result instead of crashing when it is called with the number of bits
set to 0 -- the same as what snto32() does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b63d677d63bcac06cf90@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/68753a08.050a0220.33d347.0008.GAE@google.com/
Tested-by: syzbot+b63d677d63bcac06cf90@syzkaller.appspotmail.com
Fixes: dde5845a529f ("[PATCH] Generic HID layer - code split")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/613a66cd-4309-4bce-a4f7-2905f9bce0c9@rowland.harvard.edu
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
[ s32ton() was moved by c653ffc28340 ("HID: stop exporting hid_snto32()").
Minor context change fixed. ]
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca389a55d8b2d86a817433bf82e0602b68c4d541 upstream.
logi_dj_recv_query_paired_devices() and logi_dj_recv_switch_to_dj_mode()
both have 2 callers which all log an error if the function fails. Move
the error logging to inside these 2 functions to remove the duplicated
error logging in the callers.
While at it also move the logi_dj_recv_send_report() call error handling
in logi_dj_recv_switch_to_dj_mode() to directly after the call. That call
only fails if the report cannot be found and in that case it does nothing,
so the msleep() is not necessary on failures.
Fixes: 6f20d3261265 ("HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7953794f741e94d30df9dafaaa4c031c85b891d6 upstream.
HID_GD_Z is mapped to ABS_Z for stylus and pen in hid-input.c. But HID_GD_Z
should be used to report ABS_DISTANCE for stylus and pen as described at:
Documentation/input/event-codes.rst#n226
* ABS_DISTANCE:
- Used to describe the distance of a tool from an interaction surface. This
event should only be emitted while the tool is hovering, meaning in close
proximity of the device and while the value of the BTN_TOUCH code is 0. If
the input device may be used freely in three dimensions, consider ABS_Z
instead.
- BTN_TOOL_<name> should be set to 1 when the tool comes into detectable
proximity and set to 0 when the tool leaves detectable proximity.
BTN_TOOL_<name> signals the type of tool that is currently detected by the
hardware and is otherwise independent of ABS_DISTANCE and/or BTN_TOUCH.
This patch makes the correct mapping. The ABS_DISTANCE is currently not mapped
by any HID usage in hid-generic driver.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit beab067dbcff642243291fd528355d64c41dc3b2 upstream.
Based on available evidence, the USB ID 4c4a:4155 used by multiple
devices has been attributed to Jieli. The commit 1a8953f4f774
("HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY") affected touchscreen
functionality. Added checks for manufacturer and serial number to
maintain microphone compatibility, enabling both devices to function
properly.
[jkosina@suse.com: edit shortlog]
Fixes: 1a8953f4f774 ("HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY")
Cc: stable@vger.kernel.org
Tested-by: staffan.melin@oscillator.se
Reviewed-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 53f731f5bba0cf03b751ccceb98b82fadc9ccd1e ]
Use a scope-based cleanup helper for the buffer allocated with kmalloc()
in ntrig_report_version() to simplify the cleanup logic and prevent
memory leaks (specifically the !hid_is_usb()-case one).
[jkosina@suse.com: elaborate on the actual existing leak]
Fixes: 185c926283da ("HID: hid-ntrig: fix unable to handle page fault in ntrig_report_version()")
Signed-off-by: Masami Ichikawa <masami256@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0be4253bf878d9aaa2b96031ac8683fceeb81480 ]
The Cooler Master Mice Dongle includes a vendor defined HID interface
alongside its mouse interface. Not polling it will cause the mouse to
stop responding to polls on any interface once woken up again after
going into power saving mode.
Add the HID_QUIRK_ALWAYS_POLL quirk alongside the Cooler Master VID and
the Dongle's PID.
Signed-off-by: Tristan Lobb <tristan.lobb@it-lobb.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 46f781e0d151844589dc2125c8cce3300546f92a upstream.
The sticky fingers quirk (MT_QUIRK_STICKY_FINGERS) was only considering
the case when slots were not released during the last report.
This can be problematic if the firmware forgets to release a finger
while others are still present.
This was observed on the Synaptics DLL0945 touchpad found on the Dell
XPS 9310 and the Dell Inspiron 5406.
Fixes: 4f4001bc76fd ("HID: multitouch: fix rare Win 8 cases when the touch up event gets missing")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b56cc41a3ae7323aa3c6165f93c32e020538b6d2 upstream.
As reported by syzbot, mcp2221_raw_event lacked
validation of incoming I2C read data sizes, risking buffer
overflows in mcp->rxbuf during multi-part transfers.
As highlighted in the DS20005565B spec, p44, we have:
"The number of read-back data bytes to follow in this packet:
from 0 to a maximum of 60 bytes of read-back bytes."
This patch enforces we don't exceed this limit.
Reported-by: syzbot+52c1a7d3e5b361ccd346@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=52c1a7d3e5b361ccd346
Tested-by: syzbot+52c1a7d3e5b361ccd346@syzkaller.appspotmail.com
Signed-off-by: Arnaud Lecomte <contact@arnaud-lcm.com>
Link: https://patch.msgid.link/20250726220931.7126-1-contact@arnaud-lcm.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2682468671aa0b4d52ae09779b48212a80d71b91 upstream.
When a user requests more than 60 bytes of data the MCP2221 must chunk
the data in chunks up to 60 bytes long (see command/response code 0x40
in the datasheet).
In order to signal that the device has more data the (undocumented) byte
at byte index 2 of the Get I2C Data response uses the value 0x54. This
contrasts with the case for the final data chunk where the value
returned is 0x55 (MCP2221_I2C_READ_COMPL). The fact that 0x55 was not
returned in the response was interpreted by the driver as a failure
meaning that all reads of more than 60 bytes would fail.
Add support for reads that are split over multiple chunks by looking for
the response code indicating that more data is expected and continuing
the read as the code intended. Some timing delays are required to ensure
the chip has time to refill its FIFO as data is read in from the I2C
bus. This timing has been tested in my system when configured for bus
speeds of 50KHz, 100KHz, and 400KHz and operates well.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes: 67a95c21463d0 ("HID: mcp2221: add usb to i2c-smbus host bridge")
[romain.sioen@microchip.com: backport to stable, up to 6.8. Add "Fixes" tag]
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02a46753601a24e1673d9c28173121055e8e6cc9 upstream.
Since the initial commit of this driver the I2C bus speed has been
reconfigured for every single transfer. This is despite the fact that we
never change the speed and it is never "lost" by the chip.
Upon investigation we find that what was really happening was that the
setting of the bus speed had the side effect of cancelling a previous
failed command if there was one, thereby freeing the bus. This is the
part that was actually required to keep the bus operational in the face
of failed commands.
Instead of always setting the speed, we now correctly cancel any failed
commands as they are detected. This means we can just set the bus speed
at probe time and remove the previous speed sets on each transfer.
This has the effect of improving performance and reducing the number of
commands required to complete transfers.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes: 67a95c21463d ("HID: mcp2221: add usb to i2c-smbus host bridge")
[romain.sioen@microchip.com: backport to stable, up to 6.8. Add "Fixes" tag]
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 185c926283da67a72df20a63a5046b3b4631b7d9 upstream.
in ntrig_report_version(), hdev parameter passed from hid_probe().
sending descriptor to /dev/uhid can make hdev->dev.parent->parent to null
if hdev->dev.parent->parent is null, usb_dev has
invalid address(0xffffffffffffff58) that hid_to_usb_dev(hdev) returned
when usb_rcvctrlpipe() use usb_dev,it trigger
page fault error for address(0xffffffffffffff58)
add null check logic to ntrig_report_version()
before calling hid_to_usb_dev()
Signed-off-by: Minjong Kim <minbell.kim@samsung.com>
Link: https://patch.msgid.link/20250813-hid-ntrig-page-fault-fix-v2-1-f98581f35106@samsung.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9fc51941d9e7793da969b2c66e6f8213c5b1237f upstream.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3af6ca9a8c34bbd8cff32b469b84c9021c9e7e4 upstream.
After hid_hw_start() is called hidinput_connect() will eventually be
called to set up the device with the input layer since the
HID_CONNECT_DEFAULT connect mask is used. During hidinput_connect()
all input and output reports are processed and corresponding hid_inputs
are allocated and configured via hidinput_configure_usages(). This
process involves slot tagging report fields and configuring usages
by setting relevant bits in the capability bitmaps. However it is possible
that the capability bitmaps are not set at all leading to the subsequent
hidinput_has_been_populated() check to fail leading to the freeing of the
hid_input and the underlying input device.
This becomes problematic because a malicious HID device like a
ASUS ROG N-Key keyboard can trigger the above scenario via a
specially crafted descriptor which then leads to a user-after-free
when the name of the freed input device is written to later on after
hid_hw_start(). Below, report 93 intentionally utilises the
HID_UP_UNDEFINED Usage Page which is skipped during usage
configuration, leading to the frees.
0x05, 0x0D, // Usage Page (Digitizer)
0x09, 0x05, // Usage (Touch Pad)
0xA1, 0x01, // Collection (Application)
0x85, 0x0D, // Report ID (13)
0x06, 0x00, 0xFF, // Usage Page (Vendor Defined 0xFF00)
0x09, 0xC5, // Usage (0xC5)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x04, // Report Count (4)
0xB1, 0x02, // Feature (Data,Var,Abs)
0x85, 0x5D, // Report ID (93)
0x06, 0x00, 0x00, // Usage Page (Undefined)
0x09, 0x01, // Usage (0x01)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x1B, // Report Count (27)
0x81, 0x02, // Input (Data,Var,Abs)
0xC0, // End Collection
Below is the KASAN splat after triggering the UAF:
[ 21.672709] ==================================================================
[ 21.673700] BUG: KASAN: slab-use-after-free in asus_probe+0xeeb/0xf80
[ 21.673700] Write of size 8 at addr ffff88810a0ac000 by task kworker/1:2/54
[ 21.673700]
[ 21.673700] CPU: 1 UID: 0 PID: 54 Comm: kworker/1:2 Not tainted 6.16.0-rc4-g9773391cf4dd-dirty #36 PREEMPT(voluntary)
[ 21.673700] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[ 21.673700] Call Trace:
[ 21.673700] <TASK>
[ 21.673700] dump_stack_lvl+0x5f/0x80
[ 21.673700] print_report+0xd1/0x660
[ 21.673700] kasan_report+0xe5/0x120
[ 21.673700] __asan_report_store8_noabort+0x1b/0x30
[ 21.673700] asus_probe+0xeeb/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
[ 21.673700]
[ 21.673700] Allocated by task 54:
[ 21.673700] kasan_save_stack+0x3d/0x60
[ 21.673700] kasan_save_track+0x18/0x40
[ 21.673700] kasan_save_alloc_info+0x3b/0x50
[ 21.673700] __kasan_kmalloc+0x9c/0xa0
[ 21.673700] __kmalloc_cache_noprof+0x139/0x340
[ 21.673700] input_allocate_device+0x44/0x370
[ 21.673700] hidinput_connect+0xcb6/0x2630
[ 21.673700] hid_connect+0xf74/0x1d60
[ 21.673700] hid_hw_start+0x8c/0x110
[ 21.673700] asus_probe+0x5a3/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
[ 21.673700]
[ 21.673700] Freed by task 54:
[ 21.673700] kasan_save_stack+0x3d/0x60
[ 21.673700] kasan_save_track+0x18/0x40
[ 21.673700] kasan_save_free_info+0x3f/0x60
[ 21.673700] __kasan_slab_free+0x3c/0x50
[ 21.673700] kfree+0xcf/0x350
[ 21.673700] input_dev_release+0xab/0xd0
[ 21.673700] device_release+0x9f/0x220
[ 21.673700] kobject_put+0x12b/0x220
[ 21.673700] put_device+0x12/0x20
[ 21.673700] input_free_device+0x4c/0xb0
[ 21.673700] hidinput_connect+0x1862/0x2630
[ 21.673700] hid_connect+0xf74/0x1d60
[ 21.673700] hid_hw_start+0x8c/0x110
[ 21.673700] asus_probe+0x5a3/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
Fixes: 9ce12d8be12c ("HID: asus: Add i2c touchpad support")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250810181041.44874-1-qasdev00@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
